added firmware retract. disabled by default

This commit is contained in:
Bernhard 2012-06-02 20:32:28 +02:00
parent 88d2a671cc
commit bf077125b9
5 changed files with 722 additions and 317 deletions

View File

@ -179,6 +179,16 @@ const int dropsegments=5; //everything with less than this number of steps will
#define MAX_CMD_SIZE 96
#define BUFSIZE 4
// Firmware based and LCD controled retract
// M207 and M208 can be used to define parameters for the retraction.
// The retraction can be called by the slicer using G10 and G11
// until then, intended retractions can be detected by moves that only extrude and the direction.
// the moves are than replaced by the firmware controlled ones.
// #define FWRETRACT //ONLY PARTIALLY TESTED
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
//===========================================================================
//============================= Define Defines ============================
//===========================================================================

View File

@ -50,6 +50,8 @@
// G2 - CW ARC
// G3 - CCW ARC
// G4 - Dwell S<seconds> or P<milliseconds>
// G10 - retract filament according to settings of M207
// G11 - retract recover filament according to settings of M208
// G28 - Home all Axis
// G90 - Use Absolute Coordinates
// G91 - Use Relative Coordinates
@ -102,6 +104,9 @@
// M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate
// M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk
// M206 - set additional homeing offset
// M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop]
// M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec]
// M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
// M220 S<factor in percent>- set speed factor override percentage
// M221 S<factor in percent>- set extrude factor override percentage
// M240 - Trigger a camera to take a photograph
@ -139,6 +144,12 @@ float add_homeing[3]={0,0,0};
uint8_t active_extruder = 0;
unsigned char FanSpeed=0;
#ifdef FWRETRACT
bool autoretract_enabled=true;
bool retracted=false;
float retract_length=3, retract_feedrate=17*60, retract_zlift=0.8;
float retract_recover_length=0, retract_recover_feedrate=8*60;
#endif
//===========================================================================
//=============================private variables=============================
@ -179,6 +190,7 @@ static unsigned long stoptime=0;
static uint8_t tmp_extruder;
bool Stopped=false;
//===========================================================================
@ -601,6 +613,36 @@ void process_commands()
LCD_STATUS;
}
break;
#ifdef FWRETRACT
case 10: // G10 retract
if(!retracted)
{
destination[X_AXIS]=current_position[X_AXIS];
destination[Y_AXIS]=current_position[Y_AXIS];
destination[Z_AXIS]=current_position[Z_AXIS];
current_position[Z_AXIS]+=-retract_zlift;
destination[E_AXIS]=current_position[E_AXIS]-retract_length;
feedrate=retract_feedrate;
retracted=true;
prepare_move();
}
break;
case 11: // G10 retract_recover
if(!retracted)
{
destination[X_AXIS]=current_position[X_AXIS];
destination[Y_AXIS]=current_position[Y_AXIS];
destination[Z_AXIS]=current_position[Z_AXIS];
current_position[Z_AXIS]+=retract_zlift;
current_position[E_AXIS]+=-retract_recover_length;
feedrate=retract_recover_feedrate;
retracted=false;
prepare_move();
}
break;
#endif //FWRETRACT
case 28: //G28 Home all Axis one at a time
saved_feedrate = feedrate;
saved_feedmultiply = feedmultiply;
@ -1212,6 +1254,53 @@ void process_commands()
if(code_seen(axis_codes[i])) add_homeing[i] = code_value();
}
break;
#ifdef FWRETRACT
case 207: //M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop]
{
if(code_seen('S'))
{
retract_length = code_value() ;
}
if(code_seen('F'))
{
retract_feedrate = code_value() ;
}
if(code_seen('Z'))
{
retract_zlift = code_value() ;
}
}break;
case 208: // M208 - set retract recover length S[positive mm surplus to the M207 S*] F[feedrate mm/sec]
{
if(code_seen('S'))
{
retract_recover_length = code_value() ;
}
if(code_seen('F'))
{
retract_recover_feedrate = code_value() ;
}
}break;
case 209: // M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
{
if(code_seen('S'))
{
int t= code_value() ;
switch(t)
{
case 0: autoretract_enabled=false;retracted=false;break;
case 1: autoretract_enabled=true;retracted=false;break;
default:
SERIAL_ECHO_START;
SERIAL_ECHOPGM(MSG_UNKNOWN_COMMAND);
SERIAL_ECHO(cmdbuffer[bufindr]);
SERIAL_ECHOLNPGM("\"");
}
}
}break;
#endif
case 220: // M220 S<factor in percent>- set speed factor override percentage
{
if(code_seen('S'))
@ -1373,14 +1462,55 @@ void ClearToSend()
void get_coordinates()
{
bool seen[4]={false,false,false,false};
for(int8_t i=0; i < NUM_AXIS; i++) {
if(code_seen(axis_codes[i])) destination[i] = (float)code_value() + (axis_relative_modes[i] || relative_mode)*current_position[i];
if(code_seen(axis_codes[i]))
{
destination[i] = (float)code_value() + (axis_relative_modes[i] || relative_mode)*current_position[i];
seen[i]=true;
}
else destination[i] = current_position[i]; //Are these else lines really needed?
}
if(code_seen('F')) {
next_feedrate = code_value();
if(next_feedrate > 0.0) feedrate = next_feedrate;
}
#ifdef FWRETRACT
if(autoretract_enabled)
if( !(seen[X_AXIS] || seen[Y_AXIS] || seen[Z_AXIS]) && seen[E_AXIS])
{
float echange=destination[E_AXIS]-current_position[E_AXIS];
if(echange<-MIN_RETRACT) //retract
{
if(!retracted)
{
destination[Z_AXIS]+=retract_zlift; //not sure why chaninging current_position negatively does not work.
//if slicer retracted by echange=-1mm and you want to retract 3mm, corrrectede=-2mm additionally
float correctede=-echange-retract_length;
//to generate the additional steps, not the destination is changed, but inversely the current position
destination[E_AXIS]+=correctede;
feedrate=retract_feedrate;
retracted=true;
}
}
else
if(echange>MIN_RETRACT) //retract_recover
{
if(retracted)
{
//current_position[Z_AXIS]+=-retract_zlift;
//if slicer retracted_recovered by echange=+1mm and you want to retract_recover 3mm, corrrectede=2mm additionally
float correctede=-echange+0*retract_length+retract_recover_length; //total unretract=retract_length+retract_recover_length[surplus]
current_position[E_AXIS]+=-correctede; //to generate the additional steps, not the destination is changed, but inversely the current position
feedrate=retract_recover_feedrate;
retracted=false;
}
}
}
#endif //FWRETRACT
}
void get_arc_coordinates()

View File

@ -1,316 +1,325 @@
#ifndef LANGUAGE_H
#define LANGUAGE_H
// Languages
// 1 Custom (For you to add your own messages)
// 2 English
// 3 French (Waiting translation)
// 4 German (Waiting translation)
// 5 Etc
#define LANGUAGE_CHOICE 1 // Pick your language from the list above
#define PROTOCOL_VERSION "1.0"
#if MOTHERBOARD == 7 || MOTHERBOARD == 71
#define MACHINE_NAME "Ultimaker"
#define FIRMWARE_URL "http://firmware.ultimaker.com"
#else
#define MACHINE_NAME "Mendel"
#define FIRMWARE_URL "http://www.mendel-parts.com"
#endif
#define STRINGIFY_(n) #n
#define STRINGIFY(n) STRINGIFY_(n)
#if LANGUAGE_CHOICE == 1
// LCD Menu Messages
#define WELCOME_MSG MACHINE_NAME " Ready."
#define MSG_SD_INSERTED "Card inserted"
#define MSG_SD_REMOVED "Card removed"
#define MSG_MAIN " Main \003"
#define MSG_AUTOSTART " Autostart"
#define MSG_DISABLE_STEPPERS " Disable Steppers"
#define MSG_AUTO_HOME " Auto Home"
#define MSG_SET_ORIGIN " Set Origin"
#define MSG_COOLDOWN " Cooldown"
#define MSG_EXTRUDE " Extrude"
#define MSG_PREHEAT_PLA " Preheat PLA"
#define MSG_PREHEAT_ABS " Preheat ABS"
#define MSG_MOVE_AXIS " Move Axis \x7E"
#define MSG_SPEED " Speed:"
#define MSG_NOZZLE " \002Nozzle:"
#define MSG_NOZZLE1 " \002Nozzle2:"
#define MSG_NOZZLE2 " \002Nozzle3:"
#define MSG_BED " \002Bed:"
#define MSG_FAN_SPEED " Fan speed:"
#define MSG_FLOW " Flow:"
#define MSG_CONTROL " Control \003"
#define MSG_MIN " \002 Min:"
#define MSG_MAX " \002 Max:"
#define MSG_FACTOR " \002 Fact:"
#define MSG_AUTOTEMP " Autotemp:"
#define MSG_ON "On "
#define MSG_OFF "Off"
#define MSG_PID_P " PID-P: "
#define MSG_PID_I " PID-I: "
#define MSG_PID_D " PID-D: "
#define MSG_PID_C " PID-C: "
#define MSG_ACC " Acc:"
#define MSG_VXY_JERK " Vxy-jerk: "
#define MSG_VMAX " Vmax "
#define MSG_X "x:"
#define MSG_Y "y:"
#define MSG_Z "z:"
#define MSG_E "e:"
#define MSG_VMIN " Vmin:"
#define MSG_VTRAV_MIN " VTrav min:"
#define MSG_AMAX " Amax "
#define MSG_A_RETRACT " A-retract:"
#define MSG_XSTEPS " Xsteps/mm:"
#define MSG_YSTEPS " Ysteps/mm:"
#define MSG_ZSTEPS " Zsteps/mm:"
#define MSG_ESTEPS " Esteps/mm:"
#define MSG_MAIN_WIDE " Main \003"
#define MSG_TEMPERATURE_WIDE " Temperature \x7E"
#define MSG_MOTION_WIDE " Motion \x7E"
#define MSG_STORE_EPROM " Store memory"
#define MSG_LOAD_EPROM " Load memory"
#define MSG_RESTORE_FAILSAFE " Restore Failsafe"
#define MSG_REFRESH "\004Refresh"
#define MSG_WATCH " Watch \003"
#define MSG_PREPARE " Prepare \x7E"
#define MSG_PREPARE_ALT " Prepare \003"
#define MSG_CONTROL_ARROW " Control \x7E"
#define MSG_TUNE " Tune \x7E"
#define MSG_STOP_PRINT " Stop Print \x7E"
#define MSG_CARD_MENU " Card Menu \x7E"
#define MSG_NO_CARD " No Card"
#define MSG_SERIAL_ERROR_MENU_STRUCTURE "Something is wrong in the MenuStructure."
#define MSG_DWELL "Sleep..."
#define MSG_USERWAIT "Wait for user..."
#define MSG_NO_MOVE "No move."
#define MSG_PART_RELEASE "Partial Release"
#define MSG_KILLED "KILLED. "
#define MSG_STOPPED "STOPPED. "
#define MSG_PREHEAT_PLA " Preheat PLA"
#define MSG_PREHEAT_ABS " Preheat ABS"
#define MSG_STEPPER_RELEASED "Released."
// Serial Console Messages
#define MSG_Enqueing "enqueing \""
#define MSG_POWERUP "PowerUp"
#define MSG_EXTERNAL_RESET " External Reset"
#define MSG_BROWNOUT_RESET " Brown out Reset"
#define MSG_WATCHDOG_RESET " Watchdog Reset"
#define MSG_SOFTWARE_RESET " Software Reset"
#define MSG_MARLIN "Marlin "
#define MSG_AUTHOR " | Author: "
#define MSG_CONFIGURATION_VER " Last Updated: "
#define MSG_FREE_MEMORY " Free Memory: "
#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
#define MSG_OK "ok"
#define MSG_FILE_SAVED "Done saving file."
#define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line:"
#define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line:"
#define MSG_ERR_NO_CHECKSUM "No Checksum with line number, Last Line:"
#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No Line Number with checksum, Last Line:"
#define MSG_FILE_PRINTED "Done printing file"
#define MSG_BEGIN_FILE_LIST "Begin file list"
#define MSG_END_FILE_LIST "End file list"
#define MSG_M104_INVALID_EXTRUDER "M104 Invalid extruder "
#define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
#define MSG_ERR_NO_THERMISTORS "No thermistors - no temp"
#define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
#define MSG_HEATING "Heating..."
#define MSG_HEATING_COMPLETE "Heating done."
#define MSG_BED_HEATING "Bed Heating."
#define MSG_BED_DONE "Bed done."
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
#define MSG_COUNT_X " Count X:"
#define MSG_ERR_KILLED "Printer halted. kill() called !!"
#define MSG_ERR_STOPPED "Printer stopped deu to errors. Fix the error and use M999 to restart!. (Temperature is reset. Set it before restarting)"
#define MSG_RESEND "Resend:"
#define MSG_UNKNOWN_COMMAND "Unknown command:\""
#define MSG_ACTIVE_EXTRUDER "Active Extruder: "
#define MSG_INVALID_EXTRUDER "Invalid extruder"
#define MSG_X_MIN "x_min:"
#define MSG_X_MAX "x_max:"
#define MSG_Y_MIN "y_min:"
#define MSG_Y_MAX "y_max:"
#define MSG_Z_MIN "z_min:"
#define MSG_Z_MAX "z_max:"
#define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir"
#define MSG_SD_INIT_FAIL "SD init fail"
#define MSG_SD_VOL_INIT_FAIL "volume.init failed"
#define MSG_SD_OPENROOT_FAIL "openRoot failed"
#define MSG_SD_CARD_OK "SD card ok"
#define MSG_SD_WORKDIR_FAIL "workDir open failed"
#define MSG_SD_OPEN_FILE_FAIL "open failed, File: "
#define MSG_SD_FILE_OPENED "File opened:"
#define MSG_SD_SIZE " Size:"
#define MSG_SD_FILE_SELECTED "File selected"
#define MSG_SD_WRITE_TO_FILE "Writing to file: "
#define MSG_SD_PRINTING_BYTE "SD printing byte "
#define MSG_SD_NOT_PRINTING "Not SD printing"
#define MSG_SD_ERR_WRITE_TO_FILE "error writing to file"
#define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir:"
#define MSG_STEPPER_TO_HIGH "Steprate to high : "
#define MSG_ENDSTOPS_HIT "endstops hit: "
#define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented"
#define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented"
#endif
#if LANGUAGE_CHOICE == 4
// LCD Menu Messages
#define WELCOME_MSG MACHINE_NAME " Ready."
#define MSG_SD_INSERTED "Card inserted"
#define MSG_SD_REMOVED "Card removed"
#define MSG_MAIN " Main \003"
#define MSG_AUTOSTART " Autostart"
#define MSG_DISABLE_STEPPERS " Stepper abschalten"
#define MSG_AUTO_HOME " Auto Heim"
#define MSG_SET_ORIGIN " Position setzen"
#define MSG_PREHEAT_PLA " Aufheizen PLA"
#define MSG_PREHEAT_ABS " Aufheizen ABS"
#define MSG_COOLDOWN " Abkuehlen"
#define MSG_EXTRUDE " Extrude"
#define MSG_PREHEAT_PLA " Preheat PLA"
#define MSG_PREHEAT_ABS " Preheat ABS"
#define MSG_MOVE_AXIS " Move Axis \x7E"
#define MSG_MOVE_AXIS " Achsen verfahren \x7E"
#define MSG_SPEED " Geschw:"
#define MSG_NOZZLE " \002Duese:"
#define MSG_NOZZLE1 " \002Duese2:"
#define MSG_NOZZLE2 " \002Duese3:"
#define MSG_BED " \002Bett:"
#define MSG_FAN_SPEED " Luefter geschw.:"
#define MSG_FLOW " Fluss:"
#define MSG_CONTROL " Kontrolle \003"
#define MSG_MIN " \002 Min:"
#define MSG_MAX " \002 Max:"
#define MSG_FACTOR " \002 Faktor:"
#define MSG_AUTOTEMP " AutoTemp:"
#define MSG_ON "Ein "
#define MSG_OFF "Aus "
#define MSG_PID_P " PID-P: "
#define MSG_PID_I " PID-I: "
#define MSG_PID_D " PID-D: "
#define MSG_PID_C " PID-C: "
#define MSG_ACC " Acc:"
#define MSG_VXY_JERK " Vxy-jerk: "
#define MSG_VMAX " Vmax "
#define MSG_X "x:"
#define MSG_Y "y:"
#define MSG_Z "z:"
#define MSG_E "e:"
#define MSG_VMIN " Vmin:"
#define MSG_VTRAV_MIN " VTrav min:"
#define MSG_AMAX " Amax "
#define MSG_A_RETRACT " A-retract:"
#define MSG_XSTEPS " Xsteps/mm:"
#define MSG_YSTEPS " Ysteps/mm:"
#define MSG_ZSTEPS " Zsteps/mm:"
#define MSG_ESTEPS " Esteps/mm:"
#define MSG_MAIN_WIDE " Main \003"
#define MSG_TEMPERATURE_WIDE " Temperatur \x7E"
#define MSG_MOTION_WIDE " Motion \x7E"
#define MSG_STORE_EPROM " EPROM speichern"
#define MSG_LOAD_EPROM " EPROM laden"
#define MSG_RESTORE_FAILSAFE " Standard Konfig."
#define MSG_REFRESH "\004Refresh"
#define MSG_WATCH " Beobachten \003"
#define MSG_PREPARE " Prepare \x7E"
#define MSG_PREPARE_ALT " Prepare \003"
#define MSG_CONTROL_ARROW " Control \x7E"
#define MSG_TUNE " Tune \x7E"
#define MSG_STOP_PRINT " Druck stoppen \x7E"
#define MSG_CARD_MENU " SDKarten Menue \x7E"
#define MSG_NO_CARD " Keine SDKarte"
#define MSG_SERIAL_ERROR_MENU_STRUCTURE "Fehler in der Menuestruktur."
#define MSG_DWELL "DWELL..."
#define MSG_NO_MOVE "No move."
#define MSG_PART_RELEASE "Partial Release"
#define MSG_KILLED "KILLED. "
#define MSG_STOPPED "STOPPED. "
#define MSG_PREHEAT_PLA " Preheat PLA"
#define MSG_PREHEAT_ABS " Preheat ABS"
#define MSG_STEPPER_RELEASED "Released."
// Serial Console Messages
#define MSG_Enqueing "enqueing \""
#define MSG_POWERUP "PowerUp"
#define MSG_EXTERNAL_RESET " External Reset"
#define MSG_BROWNOUT_RESET " Brown out Reset"
#define MSG_WATCHDOG_RESET " Watchdog Reset"
#define MSG_SOFTWARE_RESET " Software Reset"
#define MSG_MARLIN "Marlin: "
#define MSG_AUTHOR " | Author: "
#define MSG_CONFIGURATION_VER " Last Updated: "
#define MSG_FREE_MEMORY " Free Memory: "
#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
#define MSG_OK "ok"
#define MSG_FILE_SAVED "Done saving file."
#define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line:"
#define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line:"
#define MSG_ERR_NO_CHECKSUM "No Checksum with line number, Last Line:"
#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No Line Number with checksum, Last Line:"
#define MSG_FILE_PRINTED "Done printing file"
#define MSG_BEGIN_FILE_LIST "Begin file list"
#define MSG_END_FILE_LIST "End file list"
#define MSG_M104_INVALID_EXTRUDER "M104 Invalid extruder "
#define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
#define MSG_ERR_NO_THERMISTORS "No thermistors - no temp"
#define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
#define MSG_HEATING "Heating..."
#define MSG_HEATING_COMPLETE "Heating done."
#define MSG_BED_HEATING "Bed Heating."
#define MSG_BED_DONE "Bed done."
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
#define MSG_COUNT_X " Count X:"
#define MSG_ERR_KILLED "Printer halted. kill() called !!"
#define MSG_ERR_STOPPED "Printer stopped due to errors. Fix the error and use M999 to restart!"
#define MSG_RESEND "Resend:"
#define MSG_UNKNOWN_COMMAND "Unknown command:\""
#define MSG_ACTIVE_EXTRUDER "Active Extruder: "
#define MSG_INVALID_EXTRUDER "Invalid extruder"
#define MSG_X_MIN "x_min:"
#define MSG_X_MAX "x_max:"
#define MSG_Y_MIN "y_min:"
#define MSG_Y_MAX "y_max:"
#define MSG_Z_MIN "z_min:"
#define MSG_Z_MAX "z_max:"
#define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir"
#define MSG_SD_INIT_FAIL "SD init fail"
#define MSG_SD_VOL_INIT_FAIL "volume.init failed"
#define MSG_SD_OPENROOT_FAIL "openRoot failed"
#define MSG_SD_CARD_OK "SD card ok"
#define MSG_SD_WORKDIR_FAIL "workDir open failed"
#define MSG_SD_OPEN_FILE_FAIL "open failed, File: "
#define MSG_SD_FILE_OPENED "File opened:"
#define MSG_SD_SIZE " Size:"
#define MSG_SD_FILE_SELECTED "File selected"
#define MSG_SD_WRITE_TO_FILE "Writing to file: "
#define MSG_SD_PRINTING_BYTE "SD printing byte "
#define MSG_SD_NOT_PRINTING "Not SD printing"
#define MSG_SD_ERR_WRITE_TO_FILE "error writing to file"
#define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir:"
#define MSG_STEPPER_TO_HIGH "Steprate to high : "
#define MSG_ENDSTOPS_HIT "endstops hit: "
#define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented"
#define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented"
#endif
#ifndef LANGUAGE_H
#define LANGUAGE_H
// Languages
// 1 Custom (For you to add your own messages)
// 2 English
// 3 French (Waiting translation)
// 4 German (Waiting translation)
// 5 Etc
#define LANGUAGE_CHOICE 1 // Pick your language from the list above
#define PROTOCOL_VERSION "1.0"
#if MOTHERBOARD == 7 || MOTHERBOARD == 71
#define MACHINE_NAME "Ultimaker"
#define FIRMWARE_URL "http://firmware.ultimaker.com"
#else
#define MACHINE_NAME "Mendel"
#define FIRMWARE_URL "http://www.mendel-parts.com"
#endif
#define STRINGIFY_(n) #n
#define STRINGIFY(n) STRINGIFY_(n)
#if LANGUAGE_CHOICE == 1
// LCD Menu Messages
#define WELCOME_MSG MACHINE_NAME " Ready."
#define MSG_SD_INSERTED "Card inserted"
#define MSG_SD_REMOVED "Card removed"
#define MSG_MAIN " Main \003"
#define MSG_AUTOSTART " Autostart"
#define MSG_DISABLE_STEPPERS " Disable Steppers"
#define MSG_AUTO_HOME " Auto Home"
#define MSG_SET_ORIGIN " Set Origin"
#define MSG_COOLDOWN " Cooldown"
#define MSG_EXTRUDE " Extrude"
#define MSG_PREHEAT_PLA " Preheat PLA"
#define MSG_PREHEAT_ABS " Preheat ABS"
#define MSG_MOVE_AXIS " Move Axis \x7E"
#define MSG_SPEED " Speed:"
#define MSG_NOZZLE " \002Nozzle:"
#define MSG_NOZZLE1 " \002Nozzle2:"
#define MSG_NOZZLE2 " \002Nozzle3:"
#define MSG_BED " \002Bed:"
#define MSG_FAN_SPEED " Fan speed:"
#define MSG_FLOW " Flow:"
#define MSG_CONTROL " Control \003"
#define MSG_MIN " \002 Min:"
#define MSG_MAX " \002 Max:"
#define MSG_FACTOR " \002 Fact:"
#define MSG_AUTOTEMP " Autotemp:"
#define MSG_ON "On "
#define MSG_OFF "Off"
#define MSG_PID_P " PID-P: "
#define MSG_PID_I " PID-I: "
#define MSG_PID_D " PID-D: "
#define MSG_PID_C " PID-C: "
#define MSG_ACC " Acc:"
#define MSG_VXY_JERK " Vxy-jerk: "
#define MSG_VMAX " Vmax "
#define MSG_X "x:"
#define MSG_Y "y:"
#define MSG_Z "z:"
#define MSG_E "e:"
#define MSG_VMIN " Vmin:"
#define MSG_VTRAV_MIN " VTrav min:"
#define MSG_AMAX " Amax "
#define MSG_A_RETRACT " A-retract:"
#define MSG_XSTEPS " Xsteps/mm:"
#define MSG_YSTEPS " Ysteps/mm:"
#define MSG_ZSTEPS " Zsteps/mm:"
#define MSG_ESTEPS " Esteps/mm:"
#define MSG_MAIN_WIDE " Main \003"
#define MSG_RECTRACT_WIDE " Rectract \x7E"
#define MSG_TEMPERATURE_WIDE " Temperature \x7E"
#define MSG_MOTION_WIDE " Motion \x7E"
#define MSG_STORE_EPROM " Store memory"
#define MSG_LOAD_EPROM " Load memory"
#define MSG_RESTORE_FAILSAFE " Restore Failsafe"
#define MSG_REFRESH "\004Refresh"
#define MSG_WATCH " Watch \003"
#define MSG_PREPARE " Prepare \x7E"
#define MSG_PREPARE_ALT " Prepare \003"
#define MSG_CONTROL_ARROW " Control \x7E"
#define MSG_RETRACT_ARROW " Control \x7E"
#define MSG_TUNE " Tune \x7E"
#define MSG_STOP_PRINT " Stop Print \x7E"
#define MSG_CARD_MENU " Card Menu \x7E"
#define MSG_NO_CARD " No Card"
#define MSG_SERIAL_ERROR_MENU_STRUCTURE "Something is wrong in the MenuStructure."
#define MSG_DWELL "Sleep..."
#define MSG_USERWAIT "Wait for user..."
#define MSG_NO_MOVE "No move."
#define MSG_PART_RELEASE "Partial Release"
#define MSG_KILLED "KILLED. "
#define MSG_STOPPED "STOPPED. "
#define MSG_PREHEAT_PLA " Preheat PLA"
#define MSG_PREHEAT_ABS " Preheat ABS"
#define MSG_STEPPER_RELEASED "Released."
#define MSG_CONTROL_RETRACT " Retract mm:"
#define MSG_CONTROL_RETRACTF " Retract F:"
#define MSG_CONTROL_RETRACT_ZLIFT " Hop mm:"
#define MSG_CONTROL_RETRACT_RECOVER " UnRet +mm:"
#define MSG_CONTROL_RETRACT_RECOVERF " UnRet F:"
#define MSG_AUTORETRACT " AutoRetr.:"
// Serial Console Messages
#define MSG_Enqueing "enqueing \""
#define MSG_POWERUP "PowerUp"
#define MSG_EXTERNAL_RESET " External Reset"
#define MSG_BROWNOUT_RESET " Brown out Reset"
#define MSG_WATCHDOG_RESET " Watchdog Reset"
#define MSG_SOFTWARE_RESET " Software Reset"
#define MSG_MARLIN "Marlin "
#define MSG_AUTHOR " | Author: "
#define MSG_CONFIGURATION_VER " Last Updated: "
#define MSG_FREE_MEMORY " Free Memory: "
#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
#define MSG_OK "ok"
#define MSG_FILE_SAVED "Done saving file."
#define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line:"
#define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line:"
#define MSG_ERR_NO_CHECKSUM "No Checksum with line number, Last Line:"
#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No Line Number with checksum, Last Line:"
#define MSG_FILE_PRINTED "Done printing file"
#define MSG_BEGIN_FILE_LIST "Begin file list"
#define MSG_END_FILE_LIST "End file list"
#define MSG_M104_INVALID_EXTRUDER "M104 Invalid extruder "
#define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
#define MSG_ERR_NO_THERMISTORS "No thermistors - no temp"
#define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
#define MSG_HEATING "Heating..."
#define MSG_HEATING_COMPLETE "Heating done."
#define MSG_BED_HEATING "Bed Heating."
#define MSG_BED_DONE "Bed done."
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
#define MSG_COUNT_X " Count X:"
#define MSG_ERR_KILLED "Printer halted. kill() called !!"
#define MSG_ERR_STOPPED "Printer stopped deu to errors. Fix the error and use M999 to restart!. (Temperature is reset. Set it before restarting)"
#define MSG_RESEND "Resend:"
#define MSG_UNKNOWN_COMMAND "Unknown command:\""
#define MSG_ACTIVE_EXTRUDER "Active Extruder: "
#define MSG_INVALID_EXTRUDER "Invalid extruder"
#define MSG_X_MIN "x_min:"
#define MSG_X_MAX "x_max:"
#define MSG_Y_MIN "y_min:"
#define MSG_Y_MAX "y_max:"
#define MSG_Z_MIN "z_min:"
#define MSG_Z_MAX "z_max:"
#define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir"
#define MSG_SD_INIT_FAIL "SD init fail"
#define MSG_SD_VOL_INIT_FAIL "volume.init failed"
#define MSG_SD_OPENROOT_FAIL "openRoot failed"
#define MSG_SD_CARD_OK "SD card ok"
#define MSG_SD_WORKDIR_FAIL "workDir open failed"
#define MSG_SD_OPEN_FILE_FAIL "open failed, File: "
#define MSG_SD_FILE_OPENED "File opened:"
#define MSG_SD_SIZE " Size:"
#define MSG_SD_FILE_SELECTED "File selected"
#define MSG_SD_WRITE_TO_FILE "Writing to file: "
#define MSG_SD_PRINTING_BYTE "SD printing byte "
#define MSG_SD_NOT_PRINTING "Not SD printing"
#define MSG_SD_ERR_WRITE_TO_FILE "error writing to file"
#define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir:"
#define MSG_STEPPER_TO_HIGH "Steprate to high : "
#define MSG_ENDSTOPS_HIT "endstops hit: "
#define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented"
#define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented"
#endif
#if LANGUAGE_CHOICE == 4
// LCD Menu Messages
#define WELCOME_MSG MACHINE_NAME " Ready."
#define MSG_SD_INSERTED "Card inserted"
#define MSG_SD_REMOVED "Card removed"
#define MSG_MAIN " Main \003"
#define MSG_AUTOSTART " Autostart"
#define MSG_DISABLE_STEPPERS " Stepper abschalten"
#define MSG_AUTO_HOME " Auto Heim"
#define MSG_SET_ORIGIN " Position setzen"
#define MSG_PREHEAT_PLA " Aufheizen PLA"
#define MSG_PREHEAT_ABS " Aufheizen ABS"
#define MSG_COOLDOWN " Abkuehlen"
#define MSG_EXTRUDE " Extrude"
#define MSG_PREHEAT_PLA " Preheat PLA"
#define MSG_PREHEAT_ABS " Preheat ABS"
#define MSG_MOVE_AXIS " Move Axis \x7E"
#define MSG_MOVE_AXIS " Achsen verfahren \x7E"
#define MSG_SPEED " Geschw:"
#define MSG_NOZZLE " \002Duese:"
#define MSG_NOZZLE1 " \002Duese2:"
#define MSG_NOZZLE2 " \002Duese3:"
#define MSG_BED " \002Bett:"
#define MSG_FAN_SPEED " Luefter geschw.:"
#define MSG_FLOW " Fluss:"
#define MSG_CONTROL " Kontrolle \003"
#define MSG_MIN " \002 Min:"
#define MSG_MAX " \002 Max:"
#define MSG_FACTOR " \002 Faktor:"
#define MSG_AUTOTEMP " AutoTemp:"
#define MSG_ON "Ein "
#define MSG_OFF "Aus "
#define MSG_PID_P " PID-P: "
#define MSG_PID_I " PID-I: "
#define MSG_PID_D " PID-D: "
#define MSG_PID_C " PID-C: "
#define MSG_ACC " Acc:"
#define MSG_VXY_JERK " Vxy-jerk: "
#define MSG_VMAX " Vmax "
#define MSG_X "x:"
#define MSG_Y "y:"
#define MSG_Z "z:"
#define MSG_E "e:"
#define MSG_VMIN " Vmin:"
#define MSG_VTRAV_MIN " VTrav min:"
#define MSG_AMAX " Amax "
#define MSG_A_RETRACT " A-retract:"
#define MSG_XSTEPS " Xsteps/mm:"
#define MSG_YSTEPS " Ysteps/mm:"
#define MSG_ZSTEPS " Zsteps/mm:"
#define MSG_ESTEPS " Esteps/mm:"
#define MSG_MAIN_WIDE " Main \003"
#define MSG_TEMPERATURE_WIDE " Temperatur \x7E"
#define MSG_MOTION_WIDE " Motion \x7E"
#define MSG_STORE_EPROM " EPROM speichern"
#define MSG_LOAD_EPROM " EPROM laden"
#define MSG_RESTORE_FAILSAFE " Standard Konfig."
#define MSG_REFRESH "\004Refresh"
#define MSG_WATCH " Beobachten \003"
#define MSG_PREPARE " Prepare \x7E"
#define MSG_PREPARE_ALT " Prepare \003"
#define MSG_CONTROL_ARROW " Control \x7E"
#define MSG_TUNE " Tune \x7E"
#define MSG_STOP_PRINT " Druck stoppen \x7E"
#define MSG_CARD_MENU " SDKarten Menue \x7E"
#define MSG_NO_CARD " Keine SDKarte"
#define MSG_SERIAL_ERROR_MENU_STRUCTURE "Fehler in der Menuestruktur."
#define MSG_DWELL "DWELL..."
#define MSG_NO_MOVE "No move."
#define MSG_PART_RELEASE "Partial Release"
#define MSG_KILLED "KILLED. "
#define MSG_STOPPED "STOPPED. "
#define MSG_PREHEAT_PLA " Preheat PLA"
#define MSG_PREHEAT_ABS " Preheat ABS"
#define MSG_STEPPER_RELEASED "Released."
// Serial Console Messages
#define MSG_Enqueing "enqueing \""
#define MSG_POWERUP "PowerUp"
#define MSG_EXTERNAL_RESET " External Reset"
#define MSG_BROWNOUT_RESET " Brown out Reset"
#define MSG_WATCHDOG_RESET " Watchdog Reset"
#define MSG_SOFTWARE_RESET " Software Reset"
#define MSG_MARLIN "Marlin: "
#define MSG_AUTHOR " | Author: "
#define MSG_CONFIGURATION_VER " Last Updated: "
#define MSG_FREE_MEMORY " Free Memory: "
#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
#define MSG_OK "ok"
#define MSG_FILE_SAVED "Done saving file."
#define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line:"
#define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line:"
#define MSG_ERR_NO_CHECKSUM "No Checksum with line number, Last Line:"
#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No Line Number with checksum, Last Line:"
#define MSG_FILE_PRINTED "Done printing file"
#define MSG_BEGIN_FILE_LIST "Begin file list"
#define MSG_END_FILE_LIST "End file list"
#define MSG_M104_INVALID_EXTRUDER "M104 Invalid extruder "
#define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
#define MSG_ERR_NO_THERMISTORS "No thermistors - no temp"
#define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
#define MSG_HEATING "Heating..."
#define MSG_HEATING_COMPLETE "Heating done."
#define MSG_BED_HEATING "Bed Heating."
#define MSG_BED_DONE "Bed done."
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) "\n"
#define MSG_COUNT_X " Count X:"
#define MSG_ERR_KILLED "Printer halted. kill() called !!"
#define MSG_ERR_STOPPED "Printer stopped due to errors. Fix the error and use M999 to restart!"
#define MSG_RESEND "Resend:"
#define MSG_UNKNOWN_COMMAND "Unknown command:\""
#define MSG_ACTIVE_EXTRUDER "Active Extruder: "
#define MSG_INVALID_EXTRUDER "Invalid extruder"
#define MSG_X_MIN "x_min:"
#define MSG_X_MAX "x_max:"
#define MSG_Y_MIN "y_min:"
#define MSG_Y_MAX "y_max:"
#define MSG_Z_MIN "z_min:"
#define MSG_Z_MAX "z_max:"
#define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir"
#define MSG_SD_INIT_FAIL "SD init fail"
#define MSG_SD_VOL_INIT_FAIL "volume.init failed"
#define MSG_SD_OPENROOT_FAIL "openRoot failed"
#define MSG_SD_CARD_OK "SD card ok"
#define MSG_SD_WORKDIR_FAIL "workDir open failed"
#define MSG_SD_OPEN_FILE_FAIL "open failed, File: "
#define MSG_SD_FILE_OPENED "File opened:"
#define MSG_SD_SIZE " Size:"
#define MSG_SD_FILE_SELECTED "File selected"
#define MSG_SD_WRITE_TO_FILE "Writing to file: "
#define MSG_SD_PRINTING_BYTE "SD printing byte "
#define MSG_SD_NOT_PRINTING "Not SD printing"
#define MSG_SD_ERR_WRITE_TO_FILE "error writing to file"
#define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir:"
#define MSG_STEPPER_TO_HIGH "Steprate to high : "
#define MSG_ENDSTOPS_HIT "endstops hit: "
#define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented"
#define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented"
#endif
#endif // ifndef LANGUAGE_H

View File

@ -51,7 +51,7 @@
#define blocktime 500
#define lcdslow 5
enum MainStatus{Main_Status, Main_Menu, Main_Prepare,Sub_PrepareMove, Main_Control, Main_SD,Sub_TempControl,Sub_MotionControl};
enum MainStatus{Main_Status, Main_Menu, Main_Prepare,Sub_PrepareMove, Main_Control, Main_SD,Sub_TempControl,Sub_MotionControl,Sub_RetractControl};
class MainMenu{
public:
@ -68,6 +68,7 @@
void showControl();
void showControlMotion();
void showControlTemp();
void showControlRetract();
void showAxisMove();
void showSD();
bool force_lcd_update;

View File

@ -1688,6 +1688,8 @@ void MainMenu::showControlMotion()
}
}break;
case ItemCM_aret://float retract_acceleration = 7000;
{
if(force_lcd_update)
@ -1884,8 +1886,252 @@ void MainMenu::showControlMotion()
}
enum {
ItemR_exit,
ItemR_autoretract,
ItemR_retract_length,ItemR_retract_feedrate,ItemR_retract_zlift,
ItemR_unretract_length,ItemR_unretract_feedrate,
};
void MainMenu::showControlRetract()
{
#ifdef FWRETRACT
uint8_t line=0;
clearIfNecessary();
for(int8_t i=lineoffset;i<lineoffset+LCD_HEIGHT;i++)
{
switch(i)
{
case ItemR_exit:
MENUITEM( lcdprintPGM(MSG_CONTROL) , BLOCK;status=Main_Control;beepshort(); ) ;
break;
//float retract_length=2, retract_feedrate=1200, retract_zlift=0.4;
//float retract_recover_length=0, retract_recover_feedrate=500;
case ItemR_autoretract:
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(MSG_AUTORETRACT);
lcd.setCursor(13,line);
if(autoretract_enabled)
lcdprintPGM(MSG_ON);
else
lcdprintPGM(MSG_OFF);
}
if((activeline!=line) )
break;
if(CLICKED)
{
autoretract_enabled=!autoretract_enabled;
lcd.setCursor(13,line);
if(autoretract_enabled)
lcdprintPGM(MSG_ON);
else
lcdprintPGM(MSG_OFF);
BLOCK;
}
}break;
case ItemR_retract_length:
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(MSG_CONTROL_RETRACT);
lcd.setCursor(13,line);lcd.print(ftostr52(retract_length));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=(long)(retract_length*100);
}
else
{
retract_length= encoderpos/100.;
encoderpos=activeline*lcdslow;
}
BLOCK;
beepshort();
}
if(linechanging)
{
if(encoderpos<1) encoderpos=1;
if(encoderpos>990) encoderpos=990;
lcd.setCursor(13,line);lcd.print(ftostr52(encoderpos/100.));
}
}break;
case ItemR_retract_feedrate:
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(MSG_CONTROL_RETRACTF);
lcd.setCursor(13,line);lcd.print(itostr4(retract_feedrate));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=(long)(retract_feedrate/5);
}
else
{
retract_feedrate= encoderpos*5.;
encoderpos=activeline*lcdslow;
}
BLOCK;
beepshort();
}
if(linechanging)
{
if(encoderpos<1) encoderpos=1;
if(encoderpos>990) encoderpos=990;
lcd.setCursor(13,line);lcd.print(itostr4(encoderpos*5));
}
}break;
case ItemR_retract_zlift://float retract_acceleration = 7000;
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(MSG_CONTROL_RETRACT_ZLIFT);
lcd.setCursor(13,line);lcd.print(ftostr52(retract_zlift));;
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=(long)(retract_zlift*10);
}
else
{
retract_zlift= encoderpos/10.;
encoderpos=activeline*lcdslow;
}
BLOCK;
beepshort();
}
if(linechanging)
{
if(encoderpos<0) encoderpos=0;
if(encoderpos>990) encoderpos=990;
lcd.setCursor(13,line);lcd.print(ftostr52(encoderpos/10.));
}
}break;
case ItemR_unretract_length:
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(MSG_CONTROL_RETRACT_RECOVER);
lcd.setCursor(13,line);lcd.print(ftostr52(retract_recover_length));;
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=(long)(retract_recover_length*100);
}
else
{
retract_recover_length= encoderpos/100.;
encoderpos=activeline*lcdslow;
}
BLOCK;
beepshort();
}
if(linechanging)
{
if(encoderpos<0) encoderpos=0;
if(encoderpos>990) encoderpos=990;
lcd.setCursor(13,line);lcd.print(ftostr52(encoderpos/100.));
}
}break;
case ItemR_unretract_feedrate:
{
if(force_lcd_update)
{
lcd.setCursor(0,line);lcdprintPGM(MSG_CONTROL_RETRACT_RECOVERF);
lcd.setCursor(13,line);lcd.print(itostr4(retract_recover_feedrate));
}
if((activeline!=line) )
break;
if(CLICKED)
{
linechanging=!linechanging;
if(linechanging)
{
encoderpos=(long)retract_recover_feedrate/5;
}
else
{
retract_recover_feedrate= encoderpos*5.;
encoderpos=activeline*lcdslow;
}
BLOCK;
beepshort();
}
if(linechanging)
{
if(encoderpos<1) encoderpos=1;
if(encoderpos>990) encoderpos=990;
lcd.setCursor(13,line);lcd.print(itostr4(encoderpos*5));
}
}break;
default:
break;
}
line++;
}
updateActiveLines(ItemR_unretract_feedrate,encoderpos);
#endif
}
enum {
ItemC_exit,ItemC_temp,ItemC_move,
#ifdef FWRETRACT
ItemC_rectract,
#endif
ItemC_store, ItemC_load,ItemC_failsafe
};
@ -1906,6 +2152,11 @@ void MainMenu::showControl()
case ItemC_move:
MENUITEM( lcdprintPGM(MSG_MOTION_WIDE) , BLOCK;status=Sub_MotionControl;beepshort(); ) ;
break;
#ifdef FWRETRACT
case ItemC_rectract:
MENUITEM( lcdprintPGM(MSG_RECTRACT_WIDE) , BLOCK;status=Sub_RetractControl;beepshort(); ) ;
break;
#endif
case ItemC_store:
{
if(force_lcd_update)
@ -2250,6 +2501,10 @@ void MainMenu::update()
{
showControlMotion();
}break;
case Sub_RetractControl:
{
showControlRetract();
}break;
case Sub_TempControl:
{
showControlTemp();