Spacing, macros in LPC1768_PWM
This commit is contained in:
parent
a67cf78c6b
commit
c8718aa111
@ -153,11 +153,13 @@ void LPC1768_PWM_update_map_MR(void) {
|
||||
map_MR[0] = { 0, (uint8_t) (LPC_PWM1->PCR & _BV(8 + P1_18_PWM_channel) ? 1 : 0), P1_18, &LPC_PWM1->MR1, 0, 0, 0 };
|
||||
map_MR[1] = { 0, (uint8_t) (LPC_PWM1->PCR & _BV(8 + P1_20_PWM_channel) ? 1 : 0), P1_20, &LPC_PWM1->MR2, 0, 0, 0 };
|
||||
map_MR[2] = { 0, (uint8_t) (LPC_PWM1->PCR & _BV(8 + P1_21_PWM_channel) ? 1 : 0), P1_21, &LPC_PWM1->MR3, 0, 0, 0 };
|
||||
#if MOTHERBOARD == BOARD_MKS_SBASE
|
||||
map_MR[3] = { 0, (uint8_t) (LPC_PWM1->PCR & _BV(8 + P1_23_PWM_channel) ? 1 : 0), P1_23, &LPC_PWM1->MR4, 0, 0, 0 };
|
||||
#else
|
||||
map_MR[3] = { 0, 0, P_NC, &LPC_PWM1->MR4, 0, 0, 0 };
|
||||
#endif
|
||||
map_MR[3] = {
|
||||
#if MB(MKS_SBASE)
|
||||
0, (uint8_t) (LPC_PWM1->PCR & _BV(8 + P1_23_PWM_channel) ? 1 : 0), P1_23, &LPC_PWM1->MR4, 0, 0, 0
|
||||
#else
|
||||
0, 0, P_NC, &LPC_PWM1->MR4, 0, 0, 0
|
||||
#endif
|
||||
};
|
||||
map_MR[4] = { 0, (uint8_t) (LPC_PWM1->PCR & _BV(8 + P2_04_PWM_channel) ? 1 : 0), P2_04, &LPC_PWM1->MR5, 0, 0, 0 };
|
||||
map_MR[5] = { 0, (uint8_t) (LPC_PWM1->PCR & _BV(8 + P2_05_PWM_channel) ? 1 : 0), P2_05, &LPC_PWM1->MR6, 0, 0, 0 };
|
||||
}
|
||||
@ -212,7 +214,7 @@ void LPC1768_PWM_init(void) {
|
||||
LPC_PWM1->MR0 = LPC_PWM1_MR0; // TC resets every 19,999 + 1 cycles - sets PWM cycle(Ton+Toff) to 20 mS
|
||||
// MR0 must be set before TCR enables the PWM
|
||||
LPC_PWM1->TCR = _BV(SBIT_CNTEN) | _BV(SBIT_CNTRST) | _BV(SBIT_PWMEN); // Enable counters, reset counters, set mode to PWM
|
||||
LPC_PWM1->TCR &= ~(_BV(SBIT_CNTRST)); // Take counters out of reset
|
||||
CBI(LPC_PWM1->TCR, SBIT_CNTRST); // Take counters out of reset
|
||||
LPC_PWM1->PR = LPC_PWM1_PR;
|
||||
LPC_PWM1->MCR = _BV(SBIT_PWMMR0R) | _BV(0); // Reset TC if it matches MR0, disable all interrupts except for MR0
|
||||
LPC_PWM1->CTCR = 0; // Disable counter mode (enable PWM mode)
|
||||
@ -279,47 +281,47 @@ bool LPC1768_PWM_detach_pin(pin_t pin) {
|
||||
|
||||
// OK to make these changes before the MR0 interrupt
|
||||
switch(pin) {
|
||||
case P1_23: // MKS Sbase Servo 0, PWM1 channel 4 (J3-8 PWM1.4)
|
||||
LPC_PWM1->PCR &= ~(_BV(8 + P1_23_PWM_channel)); // disable PWM1 module control of this pin
|
||||
case P1_23: // MKS Sbase Servo 0, PWM1 channel 4 (J3-8 PWM1.4)
|
||||
CBI(LPC_PWM1->PCR, 8 + P1_23_PWM_channel); // disable PWM1 module control of this pin
|
||||
map_MR[P1_23_PWM_channel - 1].PCR_bit = 0;
|
||||
LPC_PINCON->PINSEL3 &= ~(0x3 << 14); // return pin to general purpose I/O
|
||||
LPC_PINCON->PINSEL3 &= ~(0x3 << 14); // return pin to general purpose I/O
|
||||
map_MR[P1_23_PWM_channel - 1].PINSEL_bits = 0;
|
||||
map_MR[P1_23_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
map_MR[P1_23_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
break;
|
||||
case P1_20: // Servo 0, PWM1 channel 2 (Pin 11 P1.20 PWM1.2)
|
||||
LPC_PWM1->PCR &= ~(_BV(8 + P1_20_PWM_channel)); // disable PWM1 module control of this pin
|
||||
case P1_20: // Servo 0, PWM1 channel 2 (Pin 11 P1.20 PWM1.2)
|
||||
CBI(LPC_PWM1->PCR, 8 + P1_20_PWM_channel); // disable PWM1 module control of this pin
|
||||
map_MR[P1_20_PWM_channel - 1].PCR_bit = 0;
|
||||
LPC_PINCON->PINSEL3 &= ~(0x3 << 8); // return pin to general purpose I/O
|
||||
LPC_PINCON->PINSEL3 &= ~(0x3 << 8); // return pin to general purpose I/O
|
||||
map_MR[P1_20_PWM_channel - 1].PINSEL_bits = 0;
|
||||
map_MR[P1_20_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
map_MR[P1_20_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
break;
|
||||
case P1_21: // Servo 1, PWM1 channel 3 (Pin 6 P1.21 PWM1.3)
|
||||
LPC_PWM1->PCR &= ~(_BV(8 + P1_21_PWM_channel)); // disable PWM1 module control of this pin
|
||||
case P1_21: // Servo 1, PWM1 channel 3 (Pin 6 P1.21 PWM1.3)
|
||||
CBI(LPC_PWM1->PCR, 8 + P1_21_PWM_channel); // disable PWM1 module control of this pin
|
||||
map_MR[P1_21_PWM_channel - 1].PCR_bit = 0;
|
||||
LPC_PINCON->PINSEL3 &= ~(0x3 << 10); // return pin to general purpose I/O
|
||||
LPC_PINCON->PINSEL3 &= ~(0x3 << 10); // return pin to general purpose I/O
|
||||
map_MR[P1_21_PWM_channel - 1].PINSEL_bits = 0;
|
||||
map_MR[P1_21_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
map_MR[P1_21_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
break;
|
||||
case P1_18: // Servo 3, PWM1 channel 1 (Pin 4 P1.18 PWM1.1)
|
||||
LPC_PWM1->PCR &= ~(_BV(8 + P1_18_PWM_channel)); // disable PWM1 module control of this pin
|
||||
case P1_18: // Servo 3, PWM1 channel 1 (Pin 4 P1.18 PWM1.1)
|
||||
CBI(LPC_PWM1->PCR, 8 + P1_18_PWM_channel); // disable PWM1 module control of this pin
|
||||
map_MR[P1_18_PWM_channel - 1].PCR_bit = 0;
|
||||
LPC_PINCON->PINSEL3 &= ~(0x3 << 4); // return pin to general purpose I/O
|
||||
LPC_PINCON->PINSEL3 &= ~(0x3 << 4); // return pin to general purpose I/O
|
||||
map_MR[P1_18_PWM_channel - 1].PINSEL_bits = 0;
|
||||
map_MR[P1_18_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
map_MR[P1_18_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
break;
|
||||
case P2_04: // D9 FET, PWM1 channel 5 (Pin 9 P2_04 PWM1.5)
|
||||
LPC_PWM1->PCR &= ~(_BV(8 + P2_04_PWM_channel)); // disable PWM1 module control of this pin
|
||||
case P2_04: // D9 FET, PWM1 channel 5 (Pin 9 P2_04 PWM1.5)
|
||||
CBI(LPC_PWM1->PCR, 8 + P2_04_PWM_channel); // disable PWM1 module control of this pin
|
||||
map_MR[P2_04_PWM_channel - 1].PCR_bit = 0;
|
||||
LPC_PINCON->PINSEL4 &= ~(0x3 << 10); // return pin to general purpose I/O
|
||||
LPC_PINCON->PINSEL4 &= ~(0x3 << 10); // return pin to general purpose I/O
|
||||
map_MR[P2_04_PWM_channel - 1].PINSEL_bits = 0;
|
||||
map_MR[P2_04_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
map_MR[P2_04_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
break;
|
||||
case P2_05: // D10 FET, PWM1 channel 6 (Pin 10 P2_05 PWM1.6)
|
||||
LPC_PWM1->PCR &= ~(_BV(8 + P2_05_PWM_channel)); // disable PWM1 module control of this pin
|
||||
case P2_05: // D10 FET, PWM1 channel 6 (Pin 10 P2_05 PWM1.6)
|
||||
CBI(LPC_PWM1->PCR, 8 + P2_05_PWM_channel); // disable PWM1 module control of this pin
|
||||
map_MR[P2_05_PWM_channel - 1].PCR_bit = 0;
|
||||
LPC_PINCON->PINSEL4 &= ~(0x3 << 4); // return pin to general purpose I/O
|
||||
LPC_PINCON->PINSEL4 &= ~(0x3 << 4); // return pin to general purpose I/O
|
||||
map_MR[P2_05_PWM_channel - 1].PINSEL_bits = 0;
|
||||
map_MR[P2_05_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
map_MR[P2_05_PWM_channel - 1].map_PWM_INT = 0; // 0 - available for interrupts, 1 - in use by PWM
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
@ -351,35 +353,35 @@ bool LPC1768_PWM_write(pin_t pin, uint32_t value) {
|
||||
LPC1768_PWM_update_map_MR();
|
||||
|
||||
switch(pin) {
|
||||
case P1_23: // MKS Sbase Servo 0, PWM1 channel 4 (J3-8 PWM1.4)
|
||||
map_MR[P1_23_PWM_channel - 1].PCR_bit = _BV(8 + P1_23_PWM_channel); // enable PWM1 module control of this pin
|
||||
case P1_23: // MKS Sbase Servo 0, PWM1 channel 4 (J3-8 PWM1.4)
|
||||
map_MR[P1_23_PWM_channel - 1].PCR_bit = _BV(8 + P1_23_PWM_channel); // enable PWM1 module control of this pin
|
||||
map_MR[P1_23_PWM_channel - 1].PINSEL_reg = &LPC_PINCON->PINSEL3;
|
||||
map_MR[P1_23_PWM_channel - 1].PINSEL_bits = 0x2 << 14; // ISR must do this AFTER setting PCR
|
||||
map_MR[P1_23_PWM_channel - 1].PINSEL_bits = 0x2 << 14; // ISR must do this AFTER setting PCR
|
||||
break;
|
||||
case P1_20: // Servo 0, PWM1 channel 2 (Pin 11 P1.20 PWM1.2)
|
||||
map_MR[P1_20_PWM_channel - 1].PCR_bit = _BV(8 + P1_20_PWM_channel); // enable PWM1 module control of this pin
|
||||
case P1_20: // Servo 0, PWM1 channel 2 (Pin 11 P1.20 PWM1.2)
|
||||
map_MR[P1_20_PWM_channel - 1].PCR_bit = _BV(8 + P1_20_PWM_channel); // enable PWM1 module control of this pin
|
||||
map_MR[P1_20_PWM_channel - 1].PINSEL_reg = &LPC_PINCON->PINSEL3;
|
||||
map_MR[P1_20_PWM_channel - 1].PINSEL_bits = 0x2 << 8; // ISR must do this AFTER setting PCR
|
||||
map_MR[P1_20_PWM_channel - 1].PINSEL_bits = 0x2 << 8; // ISR must do this AFTER setting PCR
|
||||
break;
|
||||
case P1_21: // Servo 1, PWM1 channel 3 (Pin 6 P1.21 PWM1.3)
|
||||
map_MR[P1_21_PWM_channel - 1].PCR_bit = _BV(8 + P1_21_PWM_channel); // enable PWM1 module control of this pin
|
||||
case P1_21: // Servo 1, PWM1 channel 3 (Pin 6 P1.21 PWM1.3)
|
||||
map_MR[P1_21_PWM_channel - 1].PCR_bit = _BV(8 + P1_21_PWM_channel); // enable PWM1 module control of this pin
|
||||
map_MR[P1_21_PWM_channel - 1].PINSEL_reg = &LPC_PINCON->PINSEL3;
|
||||
map_MR[P1_21_PWM_channel - 1].PINSEL_bits = 0x2 << 10; // ISR must do this AFTER setting PCR
|
||||
map_MR[P1_21_PWM_channel - 1].PINSEL_bits = 0x2 << 10; // ISR must do this AFTER setting PCR
|
||||
break;
|
||||
case P1_18: // Servo 3, PWM1 channel 1 (Pin 4 P1.18 PWM1.1)
|
||||
map_MR[P1_18_PWM_channel - 1].PCR_bit = _BV(8 + P1_18_PWM_channel); // enable PWM1 module control of this pin
|
||||
case P1_18: // Servo 3, PWM1 channel 1 (Pin 4 P1.18 PWM1.1)
|
||||
map_MR[P1_18_PWM_channel - 1].PCR_bit = _BV(8 + P1_18_PWM_channel); // enable PWM1 module control of this pin
|
||||
map_MR[P1_18_PWM_channel - 1].PINSEL_reg = &LPC_PINCON->PINSEL3;
|
||||
map_MR[P1_18_PWM_channel - 1].PINSEL_bits = 0x2 << 4; // ISR must do this AFTER setting PCR
|
||||
map_MR[P1_18_PWM_channel - 1].PINSEL_bits = 0x2 << 4; // ISR must do this AFTER setting PCR
|
||||
break;
|
||||
case P2_04: // D9 FET, PWM1 channel 5 (Pin 9 P2_04 PWM1.5)
|
||||
map_MR[P2_04_PWM_channel - 1].PCR_bit = _BV(8 + P2_04_PWM_channel); // enable PWM1 module control of this pin
|
||||
case P2_04: // D9 FET, PWM1 channel 5 (Pin 9 P2_04 PWM1.5)
|
||||
map_MR[P2_04_PWM_channel - 1].PCR_bit = _BV(8 + P2_04_PWM_channel); // enable PWM1 module control of this pin
|
||||
map_MR[P2_04_PWM_channel - 1].PINSEL_reg = &LPC_PINCON->PINSEL4;
|
||||
map_MR[P2_04_PWM_channel - 1].PINSEL_bits = 0x1 << 8; // ISR must do this AFTER setting PCR
|
||||
map_MR[P2_04_PWM_channel - 1].PINSEL_bits = 0x1 << 8; // ISR must do this AFTER setting PCR
|
||||
break;
|
||||
case P2_05: // D10 FET, PWM1 channel 6 (Pin 10 P2_05 PWM1.6)
|
||||
map_MR[P2_05_PWM_channel - 1].PCR_bit = _BV(8 + P2_05_PWM_channel); // enable PWM1 module control of this pin
|
||||
case P2_05: // D10 FET, PWM1 channel 6 (Pin 10 P2_05 PWM1.6)
|
||||
map_MR[P2_05_PWM_channel - 1].PCR_bit = _BV(8 + P2_05_PWM_channel); // enable PWM1 module control of this pin
|
||||
map_MR[P2_05_PWM_channel - 1].PINSEL_reg = &LPC_PINCON->PINSEL4;
|
||||
map_MR[P2_05_PWM_channel - 1].PINSEL_bits = 0x1 << 10; // ISR must do this AFTER setting PCR
|
||||
map_MR[P2_05_PWM_channel - 1].PINSEL_bits = 0x1 << 10; // ISR must do this AFTER setting PCR
|
||||
break;
|
||||
default: // ISR pins
|
||||
pinMode(pin, OUTPUT); // set pin to output
|
||||
@ -418,11 +420,11 @@ void LPC1768_PWM_update(void) { // only called by the ISR
|
||||
found = false;
|
||||
for (uint8_t j = 0; (j < NUM_PWMS) && !found; j++) {
|
||||
if ( (map_MR[j].map_PWM_PIN == ISR_table[i].pin)) {
|
||||
map_MR[j].map_PWM_INT = 1; // flag that it's already setup for direct control
|
||||
map_MR[j].map_PWM_INT = 1; // flag that it's already setup for direct control
|
||||
ISR_table[i].PWM_mask = 0;
|
||||
ISR_table[i].PCR_bit = map_MR[j].PCR_bit; // PCR register bit to enable PWM1 control of this pin
|
||||
ISR_table[i].PINSEL_reg = map_MR[j].PINSEL_reg; // PINSEL register address to set pin mode to PWM1 control} MR_map;
|
||||
ISR_table[i].PINSEL_bits = map_MR[j].PINSEL_bits; // PINSEL register bits to set pin mode to PWM1 control} MR_map;
|
||||
ISR_table[i].PCR_bit = map_MR[j].PCR_bit; // PCR register bit to enable PWM1 control of this pin
|
||||
ISR_table[i].PINSEL_reg = map_MR[j].PINSEL_reg; // PINSEL register address to set pin mode to PWM1 control} MR_map;
|
||||
ISR_table[i].PINSEL_bits = map_MR[j].PINSEL_bits; // PINSEL register bits to set pin mode to PWM1 control} MR_map;
|
||||
map_MR[j].map_used = 2;
|
||||
ISR_table[i].PWM_flag = 0;
|
||||
*map_MR[j].MR_register = ISR_table[i].microseconds;
|
||||
|
Loading…
Reference in New Issue
Block a user