diff --git a/.travis.yml b/.travis.yml index 6a33a19367..e877b2b348 100644 --- a/.travis.yml +++ b/.travis.yml @@ -388,9 +388,9 @@ script: - opt_enable AUTO_BED_LEVELING_BILINEAR Z_PROBE_ALLEN_KEY - build_marlin # - # Delta Config (Mini Kossel) + # Delta Config (FLSUN AC because it's complex) # - - use_example_configs delta/kossel_mini + - use_example_configs delta/FLSUN/auto_calibrate - build_marlin # # Makibox Config need to check board type for Teensy++ 2.0 diff --git a/Marlin/Conditionals_post.h b/Marlin/Conditionals_post.h index 78a73b27c2..02a1eb0f6b 100644 --- a/Marlin/Conditionals_post.h +++ b/Marlin/Conditionals_post.h @@ -721,6 +721,14 @@ #ifndef DELTA_TOWER_ANGLE_TRIM_3 #define DELTA_TOWER_ANGLE_TRIM_3 0.0 #endif + #if ENABLED(DELTA_AUTO_CALIBRATION) + #ifndef H_FACTOR + #define H_FACTOR 1.00 + #endif + #ifndef R_FACTOR + #define R_FACTOR -2.25 + #endif + #endif #endif /** @@ -797,6 +805,15 @@ #define HAS_FOLDER_SORTING (FOLDER_SORTING || ENABLED(SDSORT_GCODE)) #endif + // Updated G92 behavior shifts the workspace + #define HAS_POSITION_SHIFT DISABLED(NO_WORKSPACE_OFFSETS) + // The home offset also shifts the coordinate space + #define HAS_HOME_OFFSET (DISABLED(NO_WORKSPACE_OFFSETS) || ENABLED(DELTA)) + // Either offset yields extra calculations on all moves + #define HAS_WORKSPACE_OFFSET (HAS_POSITION_SHIFT || HAS_HOME_OFFSET) + // M206 doesn't apply to DELTA + #define HAS_M206_COMMAND (HAS_HOME_OFFSET && DISABLED(DELTA)) + // LCD timeout to status screen default is 15s #ifndef LCD_TIMEOUT_TO_STATUS #define LCD_TIMEOUT_TO_STATUS 15000 diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 0fca8aa5b0..188e17d547 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -695,7 +695,6 @@ //#define Z_MIN_PROBE_ENDSTOP #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index e04620dcaa..cb2b180e47 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -677,7 +677,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) @@ -971,14 +971,14 @@ #endif // ENABLED(HAVE_TMC2130) +// @section L6470 + /** * Enable this section if you have L6470 motor drivers. * You need to import the L6470 library into the Arduino IDE for this. * (https://github.com/ameyer/Arduino-L6470) */ -// @section l6470 - //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) diff --git a/Marlin/Marlin.h b/Marlin/Marlin.h index e18741a384..cea3d7fd6c 100644 --- a/Marlin/Marlin.h +++ b/Marlin/Marlin.h @@ -228,32 +228,52 @@ extern volatile bool wait_for_heatup; extern float current_position[NUM_AXIS]; // Workspace offsets -#if DISABLED(NO_WORKSPACE_OFFSETS) - extern float position_shift[XYZ], - home_offset[XYZ], - workspace_offset[XYZ]; - #define LOGICAL_POSITION(POS, AXIS) ((POS) + workspace_offset[AXIS]) - #define RAW_POSITION(POS, AXIS) ((POS) - workspace_offset[AXIS]) -#else - #define LOGICAL_POSITION(POS, AXIS) (POS) - #define RAW_POSITION(POS, AXIS) (POS) +#if HAS_WORKSPACE_OFFSET + #if HAS_HOME_OFFSET + extern float home_offset[XYZ]; + #endif + #if HAS_POSITION_SHIFT + extern float position_shift[XYZ]; + #endif #endif -#define LOGICAL_X_POSITION(POS) LOGICAL_POSITION(POS, X_AXIS) -#define LOGICAL_Y_POSITION(POS) LOGICAL_POSITION(POS, Y_AXIS) -#define LOGICAL_Z_POSITION(POS) LOGICAL_POSITION(POS, Z_AXIS) -#define RAW_X_POSITION(POS) RAW_POSITION(POS, X_AXIS) -#define RAW_Y_POSITION(POS) RAW_POSITION(POS, Y_AXIS) -#define RAW_Z_POSITION(POS) RAW_POSITION(POS, Z_AXIS) -#define RAW_CURRENT_POSITION(AXIS) RAW_POSITION(current_position[AXIS], AXIS) +#if HAS_HOME_OFFSET && HAS_POSITION_SHIFT + extern float workspace_offset[XYZ]; + #define WORKSPACE_OFFSET(AXIS) workspace_offset[AXIS] +#elif HAS_HOME_OFFSET + #define WORKSPACE_OFFSET(AXIS) home_offset[AXIS] +#elif HAS_POSITION_SHIFT + #define WORKSPACE_OFFSET(AXIS) position_shift[AXIS] +#else + #define WORKSPACE_OFFSET(AXIS) 0 +#endif +#define LOGICAL_POSITION(POS, AXIS) ((POS) + WORKSPACE_OFFSET(AXIS)) +#define RAW_POSITION(POS, AXIS) ((POS) - WORKSPACE_OFFSET(AXIS)) + +#if HAS_POSITION_SHIFT || DISABLED(DELTA) + #define LOGICAL_X_POSITION(POS) LOGICAL_POSITION(POS, X_AXIS) + #define LOGICAL_Y_POSITION(POS) LOGICAL_POSITION(POS, Y_AXIS) + #define RAW_X_POSITION(POS) RAW_POSITION(POS, X_AXIS) + #define RAW_Y_POSITION(POS) RAW_POSITION(POS, Y_AXIS) +#else + #define LOGICAL_X_POSITION(POS) (POS) + #define LOGICAL_Y_POSITION(POS) (POS) + #define RAW_X_POSITION(POS) (POS) + #define RAW_Y_POSITION(POS) (POS) +#endif + +#define LOGICAL_Z_POSITION(POS) LOGICAL_POSITION(POS, Z_AXIS) +#define RAW_Z_POSITION(POS) RAW_POSITION(POS, Z_AXIS) +#define RAW_CURRENT_POSITION(A) RAW_##A##_POSITION(current_position[A##_AXIS]) + +// Hotend Offsets #if HOTENDS > 1 extern float hotend_offset[XYZ][HOTENDS]; #endif // Software Endstops -extern float soft_endstop_min[XYZ]; -extern float soft_endstop_max[XYZ]; +extern float soft_endstop_min[XYZ], soft_endstop_max[XYZ]; #if HAS_SOFTWARE_ENDSTOPS extern bool soft_endstops_enabled; @@ -263,7 +283,7 @@ extern float soft_endstop_max[XYZ]; #define clamp_to_software_endstops(x) NOOP #endif -#if DISABLED(NO_WORKSPACE_OFFSETS) || ENABLED(DUAL_X_CARRIAGE) || ENABLED(DELTA) +#if HAS_WORKSPACE_OFFSET || ENABLED(DUAL_X_CARRIAGE) void update_software_endstops(const AxisEnum axis); #endif diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp index 2ca660c991..5626a2226f 100644 --- a/Marlin/Marlin_main.cpp +++ b/Marlin/Marlin_main.cpp @@ -61,6 +61,7 @@ * G30 - Single Z probe, probes bed at X Y location (defaults to current XY location) * G31 - Dock sled (Z_PROBE_SLED only) * G32 - Undock sled (Z_PROBE_SLED only) + * G33 - Delta '4-point' auto calibration iteration * G38 - Probe target - similar to G28 except it uses the Z_MIN_PROBE for all three axes * G90 - Use Absolute Coordinates * G91 - Use Relative Coordinates @@ -146,7 +147,7 @@ S T minimum speeds B X, Y, Z, E - * M206 - Set additional homing offset. + * M206 - Set additional homing offset. (Disabled by NO_WORKSPACE_OFFSETS or DELTA) * M207 - Set Retract Length: S, Feedrate: F, and Z lift: Z. (Requires FWRETRACT) * M208 - Set Recover (unretract) Additional (!) Length: S and Feedrate: F. (Requires FWRETRACT) * M209 - Turn Automatic Retract Detection on/off: S<0|1> (For slicers that don't support G10/11). (Requires FWRETRACT) @@ -179,7 +180,7 @@ * M410 - Quickstop. Abort all planned moves. * M420 - Enable/Disable Leveling (with current values) S1=enable S0=disable (Requires MESH_BED_LEVELING or ABL) * M421 - Set a single Z coordinate in the Mesh Leveling grid. X Y Z (Requires MESH_BED_LEVELING or AUTO_BED_LEVELING_UBL) - * M428 - Set the home_offset based on the current_position. Nearest edge applies. + * M428 - Set the home_offset based on the current_position. Nearest edge applies. (Disabled by NO_WORKSPACE_OFFSETS or DELTA) * M500 - Store parameters in EEPROM. (Requires EEPROM_SETTINGS) * M501 - Restore parameters from EEPROM. (Requires EEPROM_SETTINGS) * M502 - Revert to the default "factory settings". ** Does not write them to EEPROM! ** @@ -408,18 +409,20 @@ bool axis_relative_modes[] = AXIS_RELATIVE_MODES, float filament_size[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(DEFAULT_NOMINAL_FILAMENT_DIA), volumetric_multiplier[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(1.0); -#if DISABLED(NO_WORKSPACE_OFFSETS) - - // The distance that XYZ has been offset by G92. Reset by G28. - float position_shift[XYZ] = { 0 }; - - // This offset is added to the configured home position. - // Set by M206, M428, or menu item. Saved to EEPROM. - float home_offset[XYZ] = { 0 }; - - // The above two are combined to save on computes - float workspace_offset[XYZ] = { 0 }; - +#if HAS_WORKSPACE_OFFSET + #if HAS_POSITION_SHIFT + // The distance that XYZ has been offset by G92. Reset by G28. + float position_shift[XYZ] = { 0 }; + #endif + #if HAS_HOME_OFFSET + // This offset is added to the configured home position. + // Set by M206, M428, or menu item. Saved to EEPROM. + float home_offset[XYZ] = { 0 }; + #endif + #if HAS_HOME_OFFSET && HAS_POSITION_SHIFT + // The above two are combined to save on computes + float workspace_offset[XYZ] = { 0 }; + #endif #endif // Software Endstops are based on the configured limits. @@ -1381,7 +1384,7 @@ bool get_target_extruder_from_command(int code) { #endif // DUAL_X_CARRIAGE -#if DISABLED(NO_WORKSPACE_OFFSETS) || ENABLED(DUAL_X_CARRIAGE) || ENABLED(DELTA) +#if HAS_WORKSPACE_OFFSET || ENABLED(DUAL_X_CARRIAGE) /** * Software endstops can be used to monitor the open end of @@ -1393,7 +1396,18 @@ bool get_target_extruder_from_command(int code) { * at the same positions relative to the machine. */ void update_software_endstops(const AxisEnum axis) { - const float offs = workspace_offset[axis] = home_offset[axis] + position_shift[axis]; + const float offs = 0.0 + #if HAS_HOME_OFFSET + + home_offset[axis] + #endif + #if HAS_POSITION_SHIFT + + position_shift[axis] + #endif + ; + + #if HAS_HOME_OFFSET && HAS_POSITION_SHIFT + workspace_offset[axis] = offs; + #endif #if ENABLED(DUAL_X_CARRIAGE) if (axis == X_AXIS) { @@ -1426,8 +1440,10 @@ bool get_target_extruder_from_command(int code) { #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) { SERIAL_ECHOPAIR("For ", axis_codes[axis]); - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_HOME_OFFSET SERIAL_ECHOPAIR(" axis:\n home_offset = ", home_offset[axis]); + #endif + #if HAS_POSITION_SHIFT SERIAL_ECHOPAIR("\n position_shift = ", position_shift[axis]); #endif SERIAL_ECHOPAIR("\n soft_endstop_min = ", soft_endstop_min[axis]); @@ -1441,9 +1457,9 @@ bool get_target_extruder_from_command(int code) { #endif } -#endif // NO_WORKSPACE_OFFSETS +#endif // HAS_WORKSPACE_OFFSET || DUAL_X_CARRIAGE -#if DISABLED(NO_WORKSPACE_OFFSETS) +#if HAS_M206_COMMAND /** * Change the home offset for an axis, update the current * position and the software endstops to retain the same @@ -1457,7 +1473,7 @@ bool get_target_extruder_from_command(int code) { home_offset[axis] = v; update_software_endstops(axis); } -#endif // NO_WORKSPACE_OFFSETS +#endif // HAS_M206_COMMAND /** * Set an axis' current position to its home position (after homing). @@ -1488,7 +1504,7 @@ static void set_axis_is_at_home(AxisEnum axis) { axis_known_position[axis] = axis_homed[axis] = true; - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_POSITION_SHIFT position_shift[axis] = 0; update_software_endstops(axis); #endif @@ -1564,7 +1580,7 @@ static void set_axis_is_at_home(AxisEnum axis) { #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) { - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_HOME_OFFSET SERIAL_ECHOPAIR("> home_offset[", axis_codes[axis]); SERIAL_ECHOLNPAIR("] = ", home_offset[axis]); #endif @@ -2299,7 +2315,7 @@ static void clean_up_after_endstop_or_probe_move() { SERIAL_PROTOCOLPGM(" Y: "); SERIAL_PROTOCOL_F(y, 3); SERIAL_PROTOCOLPGM(" Z: "); - SERIAL_PROTOCOL_F(FIXFLOAT(measured_z), 3); + SERIAL_PROTOCOL_F(measured_z, 3); SERIAL_EOL; } @@ -4035,6 +4051,11 @@ inline void gcode_G28() { * L Set the Left limit of the probing grid * R Set the Right limit of the probing grid * + * Parameters with DEBUG_LEVELING_FEATURE only: + * + * C Make a totally fake grid with no actual probing. + * For use in testing when no probing is possible. + * * Parameters with BILINEAR leveling only: * * Z Supply an additional Z probe offset @@ -4077,6 +4098,12 @@ inline void gcode_G28() { #endif #endif + #if ENABLED(DEBUG_LEVELING_FEATURE) && DISABLED(PROBE_MANUALLY) + const bool faux = code_seen('C') && code_value_bool(); + #else + bool constexpr faux = false; + #endif + // Don't allow auto-leveling without homing first if (axis_unhomed_error(true, true, true)) return; @@ -4292,7 +4319,7 @@ inline void gcode_G28() { SYNC_PLAN_POSITION_KINEMATIC(); } - setup_for_endstop_or_probe_move(); + if (!faux) setup_for_endstop_or_probe_move(); //xProbe = yProbe = measured_z = 0; @@ -4550,7 +4577,7 @@ inline void gcode_G28() { if (!position_is_reachable(pos, true)) continue; #endif - measured_z = probe_pt(xProbe, yProbe, stow_probe_after_each, verbose_level); + measured_z = faux ? 0.001 * random(-100, 101) : probe_pt(xProbe, yProbe, stow_probe_after_each, verbose_level); if (isnan(measured_z)) { planner.abl_enabled = abl_should_enable; @@ -4585,7 +4612,7 @@ inline void gcode_G28() { // Retain the last probe position xProbe = LOGICAL_X_POSITION(points[i].x); yProbe = LOGICAL_Y_POSITION(points[i].y); - measured_z = points[i].z = probe_pt(xProbe, yProbe, stow_probe_after_each, verbose_level); + measured_z = points[i].z = faux ? 0.001 * random(-100, 101) : probe_pt(xProbe, yProbe, stow_probe_after_each, verbose_level); } if (isnan(measured_z)) { @@ -4624,7 +4651,7 @@ inline void gcode_G28() { // // Restore state after probing - clean_up_after_endstop_or_probe_move(); + if (!faux) clean_up_after_endstop_or_probe_move(); #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) DEBUG_POS("> probing complete", current_position); @@ -4890,8 +4917,366 @@ inline void gcode_G28() { #endif // Z_PROBE_SLED + #if ENABLED(DELTA_AUTO_CALIBRATION) + /** + * G33: Delta '4-point' auto calibration iteration + * + * Usage: G33 + * + * C (default) = Calibrate endstops, height and delta radius + * + * -2, 1-4: n x n probe points, default 3 x 3 + * + * 1: probe center + * set height only - useful when z_offset is changed + * 2: probe center and towers + * solve one '4 point' calibration + * -2: probe center and opposite the towers + * solve one '4 point' calibration + * 3: probe 3 center points, towers and opposite-towers + * averages between 2 '4 point' calibrations + * 4: probe 4 center points, towers, opposite-towers and itermediate points + * averages between 4 '4 point' calibrations + * + * V Verbose level (0-3, default 1) + * + * 0: Dry-run mode: no calibration + * 1: Settings + * 2: Setting + probe results + * 3: Expert mode: setting + iteration factors (see Configuration_adv.h) + * This prematurely stops the iteration process when factors are found + */ + inline void gcode_G33() { + + stepper.synchronize(); + + #if PLANNER_LEVELING + set_bed_leveling_enabled(false); + #endif + + const int8_t pp = code_seen('C') ? code_value_int() : DELTA_CALIBRATION_DEFAULT_POINTS, + probe_points = (WITHIN(pp, 1, 4) || pp == -2) ? pp : DELTA_CALIBRATION_DEFAULT_POINTS; + + int8_t verbose_level = code_seen('V') ? code_value_byte() : 1; + + #if ENABLED(DELTA_CALIBRATE_EXPERT_MODE) + #define _MAX_M33_V 3 + if (verbose_level == 3 && probe_points == 1) verbose_level--; // needs at least 4 points + #else + #define _MAX_M33_V 2 + if (verbose_level > 2) + SERIAL_PROTOCOLLNPGM("Enable DELTA_CALIBRATE_EXPERT_MODE in Configuration_adv.h"); + #endif + + if (!WITHIN(verbose_level, 0, _MAX_M33_V)) verbose_level = 1; + + float zero_std_dev = verbose_level ? 999.0 : 0.0; // 0.0 in dry-run mode : forced end + + gcode_G28(); + + float e_old[XYZ], + dr_old = delta_radius, + zh_old = home_offset[Z_AXIS]; + COPY(e_old,endstop_adj); + #if ENABLED(DELTA_CALIBRATE_EXPERT_MODE) + // expert variables + float h_f_old = 1.00, r_f_old = 0.00, + h_diff_min = 1.00, r_diff_max = 0.10; + #endif + + // print settings + + SERIAL_PROTOCOLLNPGM("G33 Auto Calibrate"); + SERIAL_PROTOCOLPGM("Checking... AC"); + if (verbose_level == 0) SERIAL_PROTOCOLPGM(" (DRY-RUN)"); + #if ENABLED(DELTA_CALIBRATE_EXPERT_MODE) + if (verbose_level == 3) SERIAL_PROTOCOLPGM(" (EXPERT)"); + #endif + SERIAL_EOL; + LCD_MESSAGEPGM("Checking... AC"); + + SERIAL_PROTOCOLPAIR("Height:", DELTA_HEIGHT + home_offset[Z_AXIS]); + if (abs(probe_points) > 1) { + SERIAL_PROTOCOLPGM(" Ex:"); + if (endstop_adj[A_AXIS] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(endstop_adj[A_AXIS], 2); + SERIAL_PROTOCOLPGM(" Ey:"); + if (endstop_adj[B_AXIS] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(endstop_adj[B_AXIS], 2); + SERIAL_PROTOCOLPGM(" Ez:"); + if (endstop_adj[C_AXIS] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(endstop_adj[C_AXIS], 2); + SERIAL_PROTOCOLPAIR(" Radius:", delta_radius); + } + SERIAL_EOL; + + #if ENABLED(Z_PROBE_SLED) + DEPLOY_PROBE(); + #endif + + float test_precision; + int8_t iterations = 0; + + do { // start iterations + + setup_for_endstop_or_probe_move(); + + test_precision = + #if ENABLED(DELTA_CALIBRATE_EXPERT_MODE) + // Expert mode : forced end at std_dev < 0.1 + (verbose_level == 3 && zero_std_dev < 0.1) ? 0.0 : + #endif + zero_std_dev + ; + + float z_at_pt[13] = { 0 }; + + iterations++; + + // probe the points + + int16_t center_points = 0; + + if (probe_points != 3) { + z_at_pt[0] += probe_pt(0.0, 0.0 , true, 1); + center_points = 1; + } + + int16_t step_axis = 4; + if (probe_points >= 3) { + for (int8_t axis = 9; axis > 0; axis -= step_axis) { // uint8_t starts endless loop + z_at_pt[0] += probe_pt( + 0.1 * cos(RADIANS(180 + 30 * axis)) * (DELTA_CALIBRATION_RADIUS), + 0.1 * sin(RADIANS(180 + 30 * axis)) * (DELTA_CALIBRATION_RADIUS), true, 1); + } + center_points += 3; + z_at_pt[0] /= center_points; + } + + float S1 = z_at_pt[0], S2 = sq(S1); + + int16_t N = 1, start = (probe_points == -2) ? 3 : 1; + step_axis = (abs(probe_points) == 2) ? 4 : (probe_points == 3) ? 2 : 1; + + if (probe_points != 1) { + for (uint8_t axis = start; axis < 13; axis += step_axis) + z_at_pt[axis] += probe_pt( + cos(RADIANS(180 + 30 * axis)) * (DELTA_CALIBRATION_RADIUS), + sin(RADIANS(180 + 30 * axis)) * (DELTA_CALIBRATION_RADIUS), true, 1 + ); + + if (probe_points == 4) step_axis = 2; + } + + for (uint8_t axis = start; axis < 13; axis += step_axis) { + if (probe_points == 4) + z_at_pt[axis] = (z_at_pt[axis] + (z_at_pt[axis + 1] + z_at_pt[(axis + 10) % 12 + 1]) / 2.0) / 2.0; + + S1 += z_at_pt[axis]; + S2 += sq(z_at_pt[axis]); + N++; + } + zero_std_dev = round(sqrt(S2 / N) * 1000.0) / 1000.0 + 0.00001; // deviation from zero plane + + // Solve matrices + + if (zero_std_dev < test_precision) { + COPY(e_old, endstop_adj); + dr_old = delta_radius; + zh_old = home_offset[Z_AXIS]; + + float e_delta[XYZ] = { 0.0 }, r_delta = 0.0; + + #if ENABLED(DELTA_CALIBRATE_EXPERT_MODE) + float h_f_new = 0.0, r_f_new = 0.0 , t_f_new = 0.0, + h_diff = 0.00, r_diff = 0.00; + #endif + + #define ZP(N,I) ((N) * z_at_pt[I]) + #define Z1000(I) ZP(1.00, I) + #define Z1050(I) ZP(H_FACTOR, I) + #define Z0700(I) ZP((H_FACTOR) * 2.0 / 3.00, I) + #define Z0350(I) ZP((H_FACTOR) / 3.00, I) + #define Z0175(I) ZP((H_FACTOR) / 6.00, I) + #define Z2250(I) ZP(R_FACTOR, I) + #define Z0750(I) ZP((R_FACTOR) / 3.00, I) + #define Z0375(I) ZP((R_FACTOR) / 6.00, I) + + switch (probe_points) { + case 1: + LOOP_XYZ(i) e_delta[i] = Z1000(0); + r_delta = 0.00; + break; + + case 2: + e_delta[X_AXIS] = Z1050(0) + Z0700(1) - Z0350(5) - Z0350(9); + e_delta[Y_AXIS] = Z1050(0) - Z0350(1) + Z0700(5) - Z0350(9); + e_delta[Z_AXIS] = Z1050(0) - Z0350(1) - Z0350(5) + Z0700(9); + r_delta = Z2250(0) - Z0750(1) - Z0750(5) - Z0750(9); + break; + + case -2: + e_delta[X_AXIS] = Z1050(0) - Z0700(7) + Z0350(11) + Z0350(3); + e_delta[Y_AXIS] = Z1050(0) + Z0350(7) - Z0700(11) + Z0350(3); + e_delta[Z_AXIS] = Z1050(0) + Z0350(7) + Z0350(11) - Z0700(3); + r_delta = Z2250(0) - Z0750(7) - Z0750(11) - Z0750(3); + break; + + default: + e_delta[X_AXIS] = Z1050(0) + Z0350(1) - Z0175(5) - Z0175(9) - Z0350(7) + Z0175(11) + Z0175(3); + e_delta[Y_AXIS] = Z1050(0) - Z0175(1) + Z0350(5) - Z0175(9) + Z0175(7) - Z0350(11) + Z0175(3); + e_delta[Z_AXIS] = Z1050(0) - Z0175(1) - Z0175(5) + Z0350(9) + Z0175(7) + Z0175(11) - Z0350(3); + r_delta = Z2250(0) - Z0375(1) - Z0375(5) - Z0375(9) - Z0375(7) - Z0375(11) - Z0375(3); + break; + } + + #if ENABLED(DELTA_CALIBRATE_EXPERT_MODE) + // Calculate h & r factors + if (verbose_level == 3) { + LOOP_XYZ(axis) h_f_new += e_delta[axis] / 3; + r_f_new = r_delta; + h_diff = (1.0 / H_FACTOR) * (h_f_old - h_f_new) / h_f_old; + if (h_diff < h_diff_min && h_diff > 0.9) h_diff_min = h_diff; + if (r_f_old != 0) + r_diff = ( 0.0301 * sq(R_FACTOR) * R_FACTOR + + 0.311 * sq(R_FACTOR) + + 1.1493 * R_FACTOR + + 1.7952 + ) * (r_f_old - r_f_new) / r_f_old; + if (r_diff > r_diff_max && r_diff < 0.4444) r_diff_max = r_diff; + SERIAL_EOL; + + h_f_old = h_f_new; + r_f_old = r_f_new; + } + #endif // DELTA_CALIBRATE_EXPERT_MODE + + // Adjust delta_height and endstops by the max amount + LOOP_XYZ(axis) endstop_adj[axis] += e_delta[axis]; + delta_radius += r_delta; + + const float z_temp = MAX3(endstop_adj[0], endstop_adj[1], endstop_adj[2]); + home_offset[Z_AXIS] -= z_temp; + LOOP_XYZ(i) endstop_adj[i] -= z_temp; + + recalc_delta_settings(delta_radius, delta_diagonal_rod); + } + else { // !iterate + // step one back + COPY(endstop_adj, e_old); + delta_radius = dr_old; + home_offset[Z_AXIS] = zh_old; + + recalc_delta_settings(delta_radius, delta_diagonal_rod); + } + + // print report + + #if ENABLED(DELTA_CALIBRATE_EXPERT_MODE) + if (verbose_level == 3) { + const float r_factor = 22.902 * sq(r_diff_max) * r_diff_max + - 44.988 * sq(r_diff_max) + + 31.697 * r_diff_max + - 9.4439; + SERIAL_PROTOCOLPAIR("h_factor:", 1.0 / h_diff_min); + SERIAL_PROTOCOLPAIR(" r_factor:", r_factor); + SERIAL_EOL; + } + #endif + if (verbose_level == 2) { + SERIAL_PROTOCOLPGM(". c:"); + if (z_at_pt[0] > 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(z_at_pt[0], 2); + if (probe_points > 1) { + SERIAL_PROTOCOLPGM(" x:"); + if (z_at_pt[1] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(z_at_pt[1], 2); + SERIAL_PROTOCOLPGM(" y:"); + if (z_at_pt[5] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(z_at_pt[5], 2); + SERIAL_PROTOCOLPGM(" z:"); + if (z_at_pt[9] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(z_at_pt[9], 2); + } + if (probe_points > 0) SERIAL_EOL; + if (probe_points > 2 || probe_points == -2) { + if (probe_points > 2) SERIAL_PROTOCOLPGM(". "); + SERIAL_PROTOCOLPGM(" yz:"); + if (z_at_pt[7] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(z_at_pt[7], 2); + SERIAL_PROTOCOLPGM(" zx:"); + if (z_at_pt[11] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(z_at_pt[11], 2); + SERIAL_PROTOCOLPGM(" xy:"); + if (z_at_pt[3] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(z_at_pt[3], 2); + SERIAL_EOL; + } + } + if (test_precision != 0.0) { // !forced end + if (zero_std_dev >= test_precision) { + SERIAL_PROTOCOLPGM("Calibration OK"); + SERIAL_PROTOCOLLNPGM(" rolling back 1"); + LCD_MESSAGEPGM("Calibration OK"); + SERIAL_EOL; + } + else { // !end iterations + char mess[15] = "No convergence"; + if (iterations < 31) + sprintf_P(mess, PSTR("Iteration : %02i"), (int)iterations); + SERIAL_PROTOCOL(mess); + SERIAL_PROTOCOLPGM(" std dev:"); + SERIAL_PROTOCOL_F(zero_std_dev, 3); + SERIAL_EOL; + lcd_setstatus(mess); + } + SERIAL_PROTOCOLPAIR("Height:", DELTA_HEIGHT + home_offset[Z_AXIS]); + if (abs(probe_points) > 1) { + SERIAL_PROTOCOLPGM(" Ex:"); + if (endstop_adj[A_AXIS] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(endstop_adj[A_AXIS], 2); + SERIAL_PROTOCOLPGM(" Ey:"); + if (endstop_adj[B_AXIS] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(endstop_adj[B_AXIS], 2); + SERIAL_PROTOCOLPGM(" Ez:"); + if (endstop_adj[C_AXIS] >= 0) SERIAL_CHAR('+'); + SERIAL_PROTOCOL_F(endstop_adj[C_AXIS], 2); + SERIAL_PROTOCOLPAIR(" Radius:", delta_radius); + } + SERIAL_EOL; + if (zero_std_dev >= test_precision) + SERIAL_PROTOCOLLNPGM("Save with M500"); + } + else { // forced end + #if ENABLED(DELTA_CALIBRATE_EXPERT_MODE) + if (verbose_level == 3) + SERIAL_PROTOCOLLNPGM("Copy to Configuration_adv.h"); + else + #endif + { + SERIAL_PROTOCOLPGM("End DRY-RUN std dev:"); + SERIAL_PROTOCOL_F(zero_std_dev, 3); + SERIAL_EOL; + } + } + + clean_up_after_endstop_or_probe_move(); + stepper.synchronize(); + + gcode_G28(); + + } while (zero_std_dev < test_precision && iterations < 31); + + #if ENABLED(Z_PROBE_SLED) + RETRACT_PROBE(); + #endif + } + + #endif // DELTA_AUTO_CALIBRATION + #endif // HAS_BED_PROBE + #if ENABLED(G38_PROBE_TARGET) static bool G38_run_probe() { @@ -4996,7 +5381,7 @@ inline void gcode_G92() { current_position[i] = code_value_axis_units(i); if (i != E_AXIS) didXYZ = true; #else - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_POSITION_SHIFT float p = current_position[i]; #endif float v = code_value_axis_units(i); @@ -5005,7 +5390,7 @@ inline void gcode_G92() { if (i != E_AXIS) { didXYZ = true; - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_POSITION_SHIFT position_shift[i] += v - p; // Offset the coordinate space update_software_endstops((AxisEnum)i); #endif @@ -5620,7 +6005,7 @@ inline void gcode_M42() { if (axis_unhomed_error(true, true, true)) return; - int8_t verbose_level = code_seen('V') ? code_value_byte() : 1; + const int8_t verbose_level = code_seen('V') ? code_value_byte() : 1; if (!WITHIN(verbose_level, 0, 4)) { SERIAL_PROTOCOLLNPGM("?Verbose Level not plausible (0-4)."); return; @@ -7012,7 +7397,7 @@ inline void gcode_M205() { if (code_seen('E')) planner.max_jerk[E_AXIS] = code_value_axis_units(E_AXIS); } -#if DISABLED(NO_WORKSPACE_OFFSETS) +#if HAS_M206_COMMAND /** * M206: Set Additional Homing Offset (X Y Z). SCARA aliases T=X, P=Y @@ -7031,12 +7416,13 @@ inline void gcode_M205() { report_current_position(); } -#endif // NO_WORKSPACE_OFFSETS +#endif // HAS_M206_COMMAND #if ENABLED(DELTA) /** * M665: Set delta configurations * + * H = diagonal rod // AC-version * L = diagonal rod * R = delta radius * S = segments per second @@ -7045,6 +7431,12 @@ inline void gcode_M205() { * C = Gamma (Tower 3) diagonal rod trim */ inline void gcode_M665() { + if (code_seen('H')) { + home_offset[Z_AXIS] = code_value_linear_units() - DELTA_HEIGHT; + current_position[Z_AXIS] += code_value_linear_units() - DELTA_HEIGHT - home_offset[Z_AXIS]; + home_offset[Z_AXIS] = code_value_linear_units() - DELTA_HEIGHT; + update_software_endstops(Z_AXIS); + } if (code_seen('L')) delta_diagonal_rod = code_value_linear_units(); if (code_seen('R')) delta_radius = code_value_linear_units(); if (code_seen('S')) delta_segments_per_second = code_value_float(); @@ -7903,7 +8295,7 @@ void quickstop_stepper() { #endif -#if DISABLED(NO_WORKSPACE_OFFSETS) +#if HAS_M206_COMMAND /** * M428: Set home_offset based on the distance between the @@ -7945,7 +8337,7 @@ void quickstop_stepper() { } } -#endif // NO_WORKSPACE_OFFSETS +#endif // HAS_M206_COMMAND /** * M500: Store settings in EEPROM @@ -8924,9 +9316,9 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n // The newly-selected extruder XY is actually at... current_position[X_AXIS] += xydiff[X_AXIS]; current_position[Y_AXIS] += xydiff[Y_AXIS]; - #if DISABLED(NO_WORKSPACE_OFFSETS) || ENABLED(DUAL_X_CARRIAGE) + #if HAS_WORKSPACE_OFFSET || ENABLED(DUAL_X_CARRIAGE) for (uint8_t i = X_AXIS; i <= Y_AXIS; i++) { - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_POSITION_SHIFT position_shift[i] += xydiff[i]; #endif update_software_endstops((AxisEnum)i); @@ -9192,6 +9584,15 @@ void process_next_command() { break; #endif // Z_PROBE_SLED + + #if ENABLED(DELTA_AUTO_CALIBRATION) + + case 33: // G33: Delta Auto Calibrate + gcode_G33(); + break; + + #endif // DELTA_AUTO_CALIBRATION + #endif // HAS_BED_PROBE #if ENABLED(G38_PROBE_TARGET) @@ -9509,7 +9910,7 @@ void process_next_command() { gcode_M205(); break; - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_M206_COMMAND case 206: // M206: Set home offsets gcode_M206(); break; @@ -9677,7 +10078,7 @@ void process_next_command() { break; #endif - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_M206_COMMAND case 428: // M428: Apply current_position to home_offset gcode_M428(); break; @@ -10198,8 +10599,8 @@ void set_current_from_steppers_for_axis(const AxisEnum axis) { * splitting the move where it crosses mesh borders. */ void mesh_line_to_destination(float fr_mm_s, uint8_t x_splits = 0xff, uint8_t y_splits = 0xff) { - int cx1 = mbl.cell_index_x(RAW_CURRENT_POSITION(X_AXIS)), - cy1 = mbl.cell_index_y(RAW_CURRENT_POSITION(Y_AXIS)), + int cx1 = mbl.cell_index_x(RAW_CURRENT_POSITION(X)), + cy1 = mbl.cell_index_y(RAW_CURRENT_POSITION(Y)), cx2 = mbl.cell_index_x(RAW_X_POSITION(destination[X_AXIS])), cy2 = mbl.cell_index_y(RAW_Y_POSITION(destination[Y_AXIS])); NOMORE(cx1, GRID_MAX_POINTS_X - 2); @@ -11043,6 +11444,9 @@ void disable_all_steppers() { #if ENABLED(E3_IS_TMC2130) automatic_current_control(stepperE3); #endif + #if ENABLED(E4_IS_TMC2130) + automatic_current_control(stepperE4); + #endif } } @@ -11410,7 +11814,7 @@ void setup() { // This also updates variables in the planner, elsewhere (void)settings.load(); - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_M206_COMMAND // Initialize current position based on home_offset COPY(current_position, home_offset); #else diff --git a/Marlin/configuration_store.cpp b/Marlin/configuration_store.cpp index 72cf680a01..16775bbd11 100644 --- a/Marlin/configuration_store.cpp +++ b/Marlin/configuration_store.cpp @@ -47,7 +47,7 @@ * 100 Version (char x4) * 104 EEPROM Checksum (uint16_t) * - * 106 E_STEPPERS (uint8_t) + * 106 E_STEPPERS (uint8_t) * 107 M92 XYZE planner.axis_steps_per_mm (float x4 ... x8) * 123 M203 XYZE planner.max_feedrate_mm_s (float x4 ... x8) * 139 M201 XYZE planner.max_acceleration_mm_per_s2 (uint32_t x4 ... x8) @@ -202,7 +202,7 @@ void MarlinSettings::postprocess() { calculate_volumetric_multipliers(); - #if DISABLED(NO_WORKSPACE_OFFSETS) || ENABLED(DUAL_X_CARRIAGE) || ENABLED(DELTA) + #if HAS_HOME_OFFSET || ENABLED(DUAL_X_CARRIAGE) // Software endstops depend on home_offset LOOP_XYZ(i) update_software_endstops((AxisEnum)i); #endif @@ -299,10 +299,18 @@ void MarlinSettings::postprocess() { EEPROM_WRITE(planner.min_travel_feedrate_mm_s); EEPROM_WRITE(planner.min_segment_time); EEPROM_WRITE(planner.max_jerk); - #if ENABLED(NO_WORKSPACE_OFFSETS) - float home_offset[XYZ] = { 0 }; + #if !HAS_HOME_OFFSET + const float home_offset[XYZ] = { 0 }; + #endif + #if ENABLED(DELTA) + dummy = 0.0; + EEPROM_WRITE(dummy); + EEPROM_WRITE(dummy); + dummy = DELTA_HEIGHT + home_offset[Z_AXIS]; + EEPROM_WRITE(dummy); + #else + EEPROM_WRITE(home_offset); #endif - EEPROM_WRITE(home_offset); #if HOTENDS > 1 // Skip hotend 0 which must be 0 @@ -488,7 +496,7 @@ void MarlinSettings::postprocess() { EEPROM_WRITE(dummy); } - // Save TCM2130 Configuration, and placeholder values + // Save TMC2130 Configuration, and placeholder values uint16_t val; #if ENABLED(HAVE_TMC2130) #if ENABLED(X_IS_TMC2130) @@ -551,6 +559,12 @@ void MarlinSettings::postprocess() { val = 0; #endif EEPROM_WRITE(val); + #if ENABLED(E4_IS_TMC2130) + val = stepperE4.getCurrent(); + #else + val = 0; + #endif + EEPROM_WRITE(val); #else val = 0; for (uint8_t q = 0; q < 11; ++q) EEPROM_WRITE(val); @@ -639,11 +653,17 @@ void MarlinSettings::postprocess() { EEPROM_READ(planner.min_segment_time); EEPROM_READ(planner.max_jerk); - #if ENABLED(NO_WORKSPACE_OFFSETS) + #if !HAS_HOME_OFFSET float home_offset[XYZ]; #endif EEPROM_READ(home_offset); + #if ENABLED(DELTA) + home_offset[X_AXIS] = 0.0; + home_offset[Y_AXIS] = 0.0; + home_offset[Z_AXIS] -= DELTA_HEIGHT; + #endif + #if HOTENDS > 1 // Skip hotend 0 which must be 0 for (uint8_t e = 1; e < HOTENDS; e++) @@ -979,7 +999,7 @@ void MarlinSettings::reset() { planner.z_fade_height = 0.0; #endif - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_HOME_OFFSET ZERO(home_offset); #endif @@ -1019,7 +1039,10 @@ void MarlinSettings::reset() { delta_segments_per_second = DELTA_SEGMENTS_PER_SECOND; COPY(delta_diagonal_rod_trim, drt); COPY(delta_tower_angle_trim, dta); + home_offset[Z_AXIS] = 0; + #elif ENABLED(Z_DUAL_ENDSTOPS) + float z_endstop_adj = #ifdef Z_DUAL_ENDSTOPS_ADJUSTMENT Z_DUAL_ENDSTOPS_ADJUSTMENT @@ -1027,6 +1050,7 @@ void MarlinSettings::reset() { 0 #endif ; + #endif #if ENABLED(ULTIPANEL) @@ -1143,7 +1167,7 @@ void MarlinSettings::reset() { /** * M503 - Report current settings in RAM - * + * * Unless specifically disabled, M503 is available even without EEPROM */ void MarlinSettings::report(bool forReplay) { @@ -1231,7 +1255,7 @@ void MarlinSettings::reset() { SERIAL_ECHOPAIR(" E", planner.max_jerk[E_AXIS]); SERIAL_EOL; - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_M206_COMMAND CONFIG_ECHO_START; if (!forReplay) { SERIAL_ECHOLNPGM("Home offset (mm)"); @@ -1346,11 +1370,12 @@ void MarlinSettings::reset() { SERIAL_EOL; CONFIG_ECHO_START; if (!forReplay) { - SERIAL_ECHOLNPGM("Delta settings: L=diagonal rod, R=radius, S=segments-per-second, ABC=diagonal rod trim, IJK=tower angle trim"); + SERIAL_ECHOLNPGM("Delta settings: L=diagonal_rod, R=radius, H=height, S=segments_per_second, ABC=diagonal_rod_trim_tower_[123]"); CONFIG_ECHO_START; } SERIAL_ECHOPAIR(" M665 L", delta_diagonal_rod); SERIAL_ECHOPAIR(" R", delta_radius); + SERIAL_ECHOPAIR(" H", DELTA_HEIGHT + home_offset[Z_AXIS]); SERIAL_ECHOPAIR(" S", delta_segments_per_second); SERIAL_ECHOPAIR(" A", delta_diagonal_rod_trim[A_AXIS]); SERIAL_ECHOPAIR(" B", delta_diagonal_rod_trim[B_AXIS]); diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h index 26fd884122..16ef7a4b1e 100644 --- a/Marlin/example_configurations/Cartesio/Configuration.h +++ b/Marlin/example_configurations/Cartesio/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/Cartesio/Configuration_adv.h b/Marlin/example_configurations/Cartesio/Configuration_adv.h index bfaa39d4c4..20ff965c93 100644 --- a/Marlin/example_configurations/Cartesio/Configuration_adv.h +++ b/Marlin/example_configurations/Cartesio/Configuration_adv.h @@ -674,7 +674,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index 2062fc3431..66f4decb9b 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index 3c2610e831..1095c95376 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -674,7 +674,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h index 45a8ac6b26..c48340e211 100644 --- a/Marlin/example_configurations/Felix/DUAL/Configuration.h +++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index e3a844f8d3..8ca04b48bd 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 95c0c5c05e..104c1dc803 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -674,7 +674,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h index 2b3d2487cc..732157d86e 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h index c5d3f5c6c8..90007037e8 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h @@ -658,7 +658,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index cd6e3bf763..5c6b3eaf3c 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -86,8 +86,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index 6616b12bfb..0c2cdd2a77 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -687,7 +687,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/K8400/Configuration.h b/Marlin/example_configurations/K8400/Configuration.h index 07a368c823..eb4234297a 100644 --- a/Marlin/example_configurations/K8400/Configuration.h +++ b/Marlin/example_configurations/K8400/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/K8400/Configuration_adv.h b/Marlin/example_configurations/K8400/Configuration_adv.h index 7db7af3110..ea4c7122dc 100644 --- a/Marlin/example_configurations/K8400/Configuration_adv.h +++ b/Marlin/example_configurations/K8400/Configuration_adv.h @@ -674,7 +674,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/K8400/Dual-head/Configuration.h b/Marlin/example_configurations/K8400/Dual-head/Configuration.h index 43ce27098a..dc8a06ee18 100644 --- a/Marlin/example_configurations/K8400/Dual-head/Configuration.h +++ b/Marlin/example_configurations/K8400/Dual-head/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index 5fbea32d9b..609f9ab5c1 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index d75440d73d..a90dc3f386 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h index 2badf51885..5b79424ad7 100644 --- a/Marlin/example_configurations/RigidBot/Configuration_adv.h +++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h @@ -674,7 +674,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 9b6eb56da4..08a29ee67c 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index ba87a8daa1..18c2240415 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -674,7 +674,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index ab7bb0df6e..b5ecf2b9fc 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h index e3fcad9811..4c8e8a87e9 100644 --- a/Marlin/example_configurations/TAZ4/Configuration_adv.h +++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h @@ -682,7 +682,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/TinyBoy2/Configuration.h b/Marlin/example_configurations/TinyBoy2/Configuration.h index 6581f68897..dafe44968e 100644 --- a/Marlin/example_configurations/TinyBoy2/Configuration.h +++ b/Marlin/example_configurations/TinyBoy2/Configuration.h @@ -86,8 +86,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/TinyBoy2/Configuration_adv.h b/Marlin/example_configurations/TinyBoy2/Configuration_adv.h index 4133091a0d..7983ef280d 100644 --- a/Marlin/example_configurations/TinyBoy2/Configuration_adv.h +++ b/Marlin/example_configurations/TinyBoy2/Configuration_adv.h @@ -677,7 +677,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) @@ -971,14 +971,14 @@ #endif // ENABLED(HAVE_TMC2130) +// @section L6470 + /** * Enable this section if you have L6470 motor drivers. * You need to import the L6470 library into the Arduino IDE for this. * (https://github.com/ameyer/Arduino-L6470) */ -// @section l6470 - //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 7fa675e8d2..9d66d84ec0 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index 95c0c5c05e..104c1dc803 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -674,7 +674,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index d89067b9b2..52737fdd77 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h new file mode 100644 index 0000000000..df02ad3316 --- /dev/null +++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h @@ -0,0 +1,1743 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#ifndef CONFIGURATION_H +#define CONFIGURATION_H + +/** + * + * *********************************** + * ** ATTENTION TO ALL DEVELOPERS ** + * *********************************** + * + * You must increment this version number for every significant change such as, + * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option. + * + * Note: Update also Version.h ! + */ +#define CONFIGURATION_H_VERSION 010100 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a Scara printer replace the configuration files with the files in the +// example_configurations/SCARA directory. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(LVD, FLSUN-AC)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +// +// *** VENDORS PLEASE READ ***************************************************** +// +// Marlin now allow you to have a vendor boot image to be displayed on machine +// start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your +// custom boot image and then the default Marlin boot image is shown. +// +// We suggest for you to take advantage of this new feature and keep the Marlin +// boot image unmodified. For an example have a look at the bq Hephestos 2 +// example configuration folder. +// +//#define SHOW_CUSTOM_BOOTSCREEN +// @section machine + +/** + * Select which serial port on the board will be used for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * + * :[0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 0 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_RAMPS_13_EFB +#endif + +// Optional custom name for your RepStrap or other custom machine +// Displayed in the LCD "Ready" message +#define CUSTOM_MACHINE_NAME "FLSUN Kossel" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// This defines the number of extruders +// :[1, 2, 3, 4, 5] +#define EXTRUDERS 1 + +// Enable if your E steppers or extruder gear ratios are not identical +//#define DISTINCT_E_FACTORS + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +// A dual extruder that uses a single stepper motor +// Don't forget to set SSDE_SERVO_ANGLES and HOTEND_OFFSET_X/Y/Z +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 + //#define HOTEND_OFFSET_Z {0.0, 0.0} +#endif + +/** + * "Mixing Extruder" + * - Adds a new code, M165, to set the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Host M163, M164, and virtual extruder. + * - This implementation supports only a single extruder. + * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis + +/** + * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN + * + * 0 = No Power Switch + * 1 = ATX + * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + * + * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } + */ +#define POWER_SUPPLY 0 + +#if POWER_SUPPLY > 0 + // Enable this option to leave the PSU off at startup. + // Power to steppers and heaters will need to be turned on with M80. + //#define PS_DEFAULT_OFF +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" } + */ +#define TEMP_SENSOR_0 5 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_BED 5 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5 + +// Extruder temperature must be close to target for this long before M109 returns success +#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// Bed temperature must be close to target for this long before M190 returns success +#define TEMP_BED_RESIDENCY_TIME 1 // (seconds) +#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define BED_MINTEMP 5 + +// When temperature exceeds max temp, your heater will be switched off. +// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +// You should use MINTEMP for thermistor short/failure protection. +#define HEATER_0_MAXTEMP 250 +#define HEATER_1_MAXTEMP 250 +#define HEATER_2_MAXTEMP 250 +#define HEATER_3_MAXTEMP 250 +#define HEATER_4_MAXTEMP 250 +#define BED_MAXTEMP 115 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#if ENABLED(PIDTEMP) + #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + #define K1 0.95 //smoothing factor within the PID + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + // Ultimaker + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + + //E3D with 30MM fan + #define DEFAULT_Kp 24.77 + #define DEFAULT_Ki 1.84 + #define DEFAULT_Kd 83.61 + +#endif // PIDTEMP + +//=========================================================================== +//============================= PID > Bed Temperature Control =============== +//=========================================================================== +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + //D-force + #define DEFAULT_bedKp 22.97 + #define DEFAULT_bedKi 3.76 + #define DEFAULT_bedKd 29.2 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +// This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP. +// It also enables the M302 command to set the minimum extrusion temperature +// or to allow moving the extruder regardless of the hotend temperature. +// *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 300 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== +// Enable DELTA kinematics and most of the default configuration for Deltas +#define DELTA + +#if ENABLED(DELTA) + + // Make delta curves from many straight lines (linear interpolation). + // This is a trade-off between visible corners (not enough segments) + // and processor overload (too many expensive sqrt calls). + #define DELTA_SEGMENTS_PER_SECOND 160 + + // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them + + // Center-to-center distance of the holes in the diagonal push rods. + #define DELTA_DIAGONAL_ROD 218.0 // mm + + // Horizontal offset from middle of printer to smooth rod center. + //#define DELTA_SMOOTH_ROD_OFFSET 150.0 // mm + + // Horizontal offset of the universal joints on the end effector. + //#define DELTA_EFFECTOR_OFFSET 24.0 // mm + + // Horizontal offset of the universal joints on the carriages. + //#define DELTA_CARRIAGE_OFFSET 22.0 // mm + + // Horizontal distance bridged by diagonal push rods when effector is centered. + #define DELTA_RADIUS 100.59 //mm // get this value from auto calibrate + + // height from z=0.00 to home position + #define DELTA_HEIGHT 298.95 // get this value from auto calibrate + + // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). + #define DELTA_PRINTABLE_RADIUS 90.0 + + // Delta calibration menu + // uncomment to add three points calibration menu option. + // See http://minow.blogspot.com/index.html#4918805519571907051 + #define DELTA_CALIBRATION_MENU + + // G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results) + #define DELTA_AUTO_CALIBRATION + #if ENABLED(DELTA_AUTO_CALIBRATION) + #define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (1-4) + #define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 15) // set the radius for the calibration probe points + #endif + + // After homing move down to a height where XY movement is unconstrained + #define DELTA_HOME_TO_SAFE_ZONE + + #define DELTA_ENDSTOP_ADJ { -0.05, -0.00, -0.02 } // get these from auto calibrate + + // Trim adjustments for individual towers + #define DELTA_RADIUS_TRIM_TOWER_1 0.0 + #define DELTA_RADIUS_TRIM_TOWER_2 0.0 + #define DELTA_RADIUS_TRIM_TOWER_3 0.0 + #define DELTA_DIAGONAL_ROD_TRIM_TOWER_1 0.0 + #define DELTA_DIAGONAL_ROD_TRIM_TOWER_2 0.0 + #define DELTA_DIAGONAL_ROD_TRIM_TOWER_3 0.0 + #define DELTA_TOWER_ANGLE_TRIM_1 0.0 + #define DELTA_TOWER_ANGLE_TRIM_2 0.0 + #define DELTA_TOWER_ANGLE_TRIM_3 0.0 + +#endif + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +//#define USE_XMIN_PLUG +//#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +#define USE_XMAX_PLUG +#define USE_YMAX_PLUG +#define USE_ZMAX_PLUG + +// coarse Endstop Settings +#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors + +#if DISABLED(ENDSTOPPULLUPS) + // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe. + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +// delta speeds must be the same on xyz +/** + * Default Settings + * + * These settings can be reset by M502 + * + * You can set distinct factors for each E stepper, if needed. + * If fewer factors are given, the last will apply to the rest. + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 100, 100 } // default steps per unit for Kossel (GT2, 20 tooth) + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3]]] + */ +#define DEFAULT_MAX_FEEDRATE { 200, 200, 200, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3]]] + */ +#define DEFAULT_MAX_ACCELERATION { 4000, 4000, 4000, 4000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XJERK 20.0 +#define DEFAULT_YJERK DEFAULT_XJERK +#define DEFAULT_ZJERK DEFAULT_YJERK // Must be same as XY for delta +#define DEFAULT_EJERK 5.0 + + +/** + * =========================================================================== + * ============================= Z Probe Options ============================= + * =========================================================================== + * @section probes + * + * + * Probe Type + * Probes are sensors/switches that are activated / deactivated before/after use. + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * You must activate one of these to use Auto Bed Leveling below. + * + * Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * For example an inductive probe, or a setup that uses the nozzle to probe. + * An inductive probe must be deactivated to go below + * its trigger-point if hardware endstops are active. + */ +#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + * NUM_SERVOS also needs to be set. This is found later in this file. Set it to + * 1 + the number of other servos in your system. + */ +//#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + + /** + * The BLTouch probe emulates a servo probe. + * If using a BLTouch then NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES + * are setup for you in the background and you shouldn't need to set/modify/enable them + * with the possible exception of Z_ENDSTOP_SERVO_NR. + */ +//#define BLTOUCH +//#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed + +/** + * BLTouch WARNING - ONLY APPLIES TO VERSIONS OF MARLIN BEFORE 15 FEB 2017 + * Unless using interrupt endstops, there is a MINIMUM feedrate for Marlin to reliably + * sense the BLTouch. If the feedrate is too slow then G28 & G29 can sometimes result + * in the print head being driven into the bed until manual intervention. + * The minimum feedrate calculation is: + * + * feedrate minimum = 24000 / DEFAULT_AXIS_STEPS_PER_UNIT + * where feedrate is in "mm/minute" or "inches/minute" depending on the units used + * in DEFAULT_AXIS_STEPS_PER_UNIT + * + * This applies to the HOMING_FEEDRATE_Z and Z_PROBE_SPEED_FAST. If PROBE_DOUBLE_TOUCH + * is enabled then it also applies to Z_PROBE_SPEED_SLOW. + */ + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.25 // Z offset: -below +above [the nozzle] + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 5000 + +// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Speed for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 4) + +// Use double touch for probing +//#define PROBE_DOUBLE_TOUCH + +/** + * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe + * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. + */ +//#define Z_PROBE_ALLEN_KEY + +#if ENABLED(Z_PROBE_ALLEN_KEY) + // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, + // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. + + // Kossel Mini + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_SPEED + + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED/10) + + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75 + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75 + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED + + #define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20 + // Move the probe into position + #define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_SPEED + // Move the nozzle down further to push the probe into retracted position. + #define Z_PROBE_ALLEN_KEY_STOW_2_X Z_PROBE_ALLEN_KEY_STOW_1_X + #define Z_PROBE_ALLEN_KEY_STOW_2_Y Z_PROBE_ALLEN_KEY_STOW_1_Y + #define Z_PROBE_ALLEN_KEY_STOW_2_Z (Z_PROBE_ALLEN_KEY_STOW_1_Z-Z_PROBE_ALLEN_KEY_STOW_DEPTH) + #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_SPEED/10) + // Raise things back up slightly so we don't bump into anything + #define Z_PROBE_ALLEN_KEY_STOW_3_X Z_PROBE_ALLEN_KEY_STOW_2_X + #define Z_PROBE_ALLEN_KEY_STOW_3_Y Z_PROBE_ALLEN_KEY_STOW_2_Y + #define Z_PROBE_ALLEN_KEY_STOW_3_Z (Z_PROBE_ALLEN_KEY_STOW_1_Z+Z_PROBE_ALLEN_KEY_STOW_DEPTH) + #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE (XY_PROBE_SPEED/2) + + #define Z_PROBE_ALLEN_KEY_STOW_4_X 0.0 + #define Z_PROBE_ALLEN_KEY_STOW_4_Y 0.0 + #define Z_PROBE_ALLEN_KEY_STOW_4_Z Z_PROBE_ALLEN_KEY_STOW_3_Z + #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_SPEED + +#endif // Z_PROBE_ALLEN_KEY + +/** + * + * *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** + * + * - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. + * - Use 5V for powered (usu. inductive) sensors. + * - Otherwise connect: + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + * Normally-closed switches are advised and are the default. + * + * + * PIN OPTIONS\SETUP FOR Z PROBES + * + * + * WARNING: + * Setting the wrong pin may have unexpected and potentially disastrous consequences. + * Use with caution and do your homework. + * + * + * All Z PROBE pin options are configured by defining (or not defining) + * the following five items: + * Z_MIN_PROBE_ENDSTOP – defined below + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN – defined below + * Z_MIN_PIN - defined in the pins_YOUR_BOARD.h file + * Z_MIN_PROBE_PIN - defined in the pins_YOUR_BOARD.h file + * + * If you're using a probe then you need to tell Marlin which pin to use as + * the Z MIN ENDSTOP. Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN determines if the + * Z_MIN_PIN or if the Z_MIN_PROBE_PIN is used. + * + * The pin selected for the probe is ONLY checked during probing operations. + * If you want to use the Z_MIN_PIN as an endstop AND you want to have a Z PROBE + * then you’ll need to use the Z_MIN_PROBE_PIN option. + * + * Z_MIN_PROBE_ENDSTOP also needs to be enabled if you want to use Z_MIN_PROBE_PIN. + * + * The settings needed to use the Z_MIN_PROBE_PIN are: + * 1. select the type of probe you're using + * 2. define Z_MIN_PROBE_PIN in your pins_YOUR_BOARD.h file + * 3. disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * 4. enable Z_MIN_PROBE_ENDSTOP + * NOTE – if Z_MIN_PIN is defined then it’ll be checked during all moves in the + * negative Z direction. + * + * The settings needed to use the Z_MIN_PIN are: + * 1. select the type of probe you're using + * 2. enable Z_MIN _PIN in your pins_YOUR_BOARD.h file + * 3. enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * 4. disable Z_MIN_PROBE_ENDSTOP + * NOTES – if Z_MIN_PROBE_PIN is defined in the pins_YOUR_BOARD.h file then it’ll be + * ignored by Marlin + */ + +//#define Z_MIN_PROBE_ENDSTOP // A3K leave disabled! +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// Enable Z Probe Repeatability test to see how accurate your probe is +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR true // DELTA does not invert +#define INVERT_Y_DIR true +#define INVERT_Z_DIR true + +// Enable this option for Toshiba steppers +//#define CONFIG_STEPPERS_TOSHIBA + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false + +// @section homing + +#define Z_HOMING_HEIGHT 15 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR 1 // deltas always home to max +#define Y_HOME_DIR 1 +#define Z_HOME_DIR 1 + +// @section machine + +// Travel limits after homing (units are in mm) +#define X_MIN_POS -(DELTA_PRINTABLE_RADIUS) +#define Y_MIN_POS -(DELTA_PRINTABLE_RADIUS) +#define Z_MIN_POS 0 +#define X_MAX_POS DELTA_PRINTABLE_RADIUS +#define Y_MAX_POS DELTA_PRINTABLE_RADIUS +#define Z_MAX_POS MANUAL_Z_HOME_POS + +// If enabled, axes won't move below MIN_POS in response to movement commands. +//#define MIN_SOFTWARE_ENDSTOPS +// If enabled, axes won't move above MAX_POS in response to movement commands. +#define MAX_SOFTWARE_ENDSTOPS + +/** + * Filament Runout Sensor + * A mechanical or opto endstop is used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN. + * For other boards you may need to define FIL_RUNOUT_PIN. + * By default the firmware assumes HIGH = has filament, LOW = ran out + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor. + #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. + #define FILAMENT_RUNOUT_SCRIPT "M600" +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section bedlevel + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. Currently, UBL is only checked out + * for Cartesian Printers. That said, it was primarily designed to correct + * poor quality Delta Printers. If you feel adventurous and have a Delta, + * please post an issue if something doesn't work correctly. Initially, + * you will need to set a reduced bed size so you have a rectangular area + * to test on. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + //#define ENABLE_LEVELING_FADE_HEIGHT +#endif + +#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 9 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 15) + #define LEFT_PROBE_BED_POSITION -(DELTA_PROBEABLE_RADIUS) + #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS + #define FRONT_PROBE_BED_POSITION -(DELTA_PROBEABLE_RADIUS) + #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS + + // The Z probe minimum outer margin (to validate G29 parameters). + #define MIN_PROBE_EDGE 10 + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_3POINT) + + // 3 arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + #define UBL_MESH_INSET 1 // Mesh inset margin on print area + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + #define UBL_PROBE_PT_1_X 39 // These set the probe locations for when UBL does a 3-Point leveling + #define UBL_PROBE_PT_1_Y 180 // of the mesh. + #define UBL_PROBE_PT_2_X 39 + #define UBL_PROBE_PT_2_Y 20 + #define UBL_PROBE_PT_3_X 180 + #define UBL_PROBE_PT_3_Y 20 + //#define UBL_G26_MESH_EDITING // Enable G26 mesh editing + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Mesh inset margin on print area + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Use the LCD controller for bed leveling + * Requires MESH_BED_LEVELING or PROBE_MANUALLY + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +#define MANUAL_Z_HOME_POS DELTA_HEIGHT // Distance between the nozzle to printbed after homing + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28). +#endif + +// Delta only homes to Z +#define HOMING_FEEDRATE_Z (100*60) + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +// +// EEPROM +// +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +//define this to enable EEPROM support +#define EEPROM_SETTINGS + +#if ENABLED(EEPROM_SETTINGS) + // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: + #define EEPROM_CHITCHAT // Please keep turned on if you can. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 5 // Number of seconds between "busy" messages. Set with M113. + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_TEMP_HOTEND 185 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 100 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +// +// Nozzle Park -- EXPERIMENTAL +// +// When enabled allows the user to define a special XYZ position, inside the +// machine's topology, to park the nozzle when idle or when receiving the G27 +// command. +// +// The "P" paramenter controls what is the action applied to the Z axis: +// P0: (Default) If current Z-pos is lower than Z-park then the nozzle will +// be raised to reach Z-park height. +// +// P1: No matter the current Z-pos, the nozzle will be raised/lowered to +// reach Z-park height. +// +// P2: The nozzle height will be raised by Z-park amount but never going over +// the machine's limit of Z_MAX_POS. +// +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } +#endif + +// +// Clean Nozzle Feature -- EXPERIMENTAL +// +// When enabled allows the user to send G12 to start the nozzle cleaning +// process, the G-Code accepts two parameters: +// "P" for pattern selection +// "S" for defining the number of strokes/repetitions +// +// Available list of patterns: +// P0: This is the default pattern, this process requires a sponge type +// material at a fixed bed location. S defines "strokes" i.e. +// back-and-forth movements between the starting and end points. +// +// P1: This starts a zig-zag pattern between (X0, Y0) and (X1, Y1), "T" +// defines the number of zig-zag triangles to be done. "S" defines the +// number of strokes aka one back-and-forth movement. Zig-zags will +// be performed in whichever dimension is smallest. As an example, +// sending "G12 P1 S1 T3" will execute: +// +// -- +// | (X0, Y1) | /\ /\ /\ | (X1, Y1) +// | | / \ / \ / \ | +// A | | / \ / \ / \ | +// | | / \ / \ / \ | +// | (X0, Y0) | / \/ \/ \ | (X1, Y0) +// -- +--------------------------------+ +// |________|_________|_________| +// T1 T2 T3 +// +// P2: This starts a circular pattern with circle with middle in +// NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S. +// Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT. +// +// Caveats: End point Z should use the same value as Start point Z. +// +// Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments +// may change to add new functionality like different wipe patterns. +// +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)} + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Moves the nozzle to the initial position + #define NOZZLE_CLEAN_GOBACK +#endif + +// +// Print job timer +// +// Enable this option to automatically start and stop the +// print job timer when M104/M109/M190 commands are received. +// M104 (extruder without wait) - high temp = none, low temp = stop timer +// M109 (extruder with wait) - high temp = start timer, low temp = stop timer +// M190 (bed with wait) - high temp = start timer, low temp = none +// +// In all cases the timer can be started and stopped using +// the following commands: +// +// - M75 - Start the print job timer +// - M76 - Pause the print job timer +// - M77 - Stop the print job timer +#define PRINTJOB_TIMER_AUTOSTART + +// +// Print Counter +// +// When enabled Marlin will keep track of some print statistical data such as: +// - Total print jobs +// - Total successful print jobs +// - Total failed print jobs +// - Total time printing +// +// This information can be viewed by the M78 command. +#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +// +// LCD LANGUAGE +// +// Here you may choose the language used by Marlin on the LCD menus, the following +// list of languages are available: +// en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it, +// kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk, test +// +// :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'test':'TEST' } +// +#define LCD_LANGUAGE en + +// +// LCD Character Set +// +// Note: This option is NOT applicable to Graphical Displays. +// +// All character-based LCD's provide ASCII plus one of these +// language extensions: +// +// - JAPANESE ... the most common +// - WESTERN ... with more accented characters +// - CYRILLIC ... for the Russian language +// +// To determine the language extension installed on your controller: +// +// - Compile and upload with LCD_LANGUAGE set to 'test' +// - Click the controller to view the LCD menu +// - The LCD will display Japanese, Western, or Cyrillic text +// +// See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language +// +// :['JAPANESE', 'WESTERN', 'CYRILLIC'] +// +#define DISPLAY_CHARSET_HD44780 WESTERN + +// +// LCD TYPE +// +// You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2, +// 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels +// (ST7565R family). (This option will be set automatically for certain displays.) +// +// IMPORTANT NOTE: The U8glib library is required for Full Graphic Display! +// https://github.com/olikraus/U8glib_Arduino +// +//#define ULTRA_LCD // Character based +//#define DOGLCD // Full graphics display + +// +// SD CARD +// +// SD Card support is disabled by default. If your controller has an SD slot, +// you must uncomment the following option or it won't work. +// +#define SDSUPPORT + +// +// SD CARD: SPI SPEED +// +// Uncomment ONE of the following items to use a slower SPI transfer +// speed. This is usually required if you're getting volume init errors. +// +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +// +// SD CARD: ENABLE CRC +// +// Use CRC checks and retries on the SD communication. +// +#define SD_CHECK_AND_RETRY + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 1 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 5 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +// INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics. +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 +//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 + +// +// CONTROLLER TYPE: Standard +// +// Marlin supports a wide variety of controllers. +// Enable one of the following options to specify your controller. +// + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0 + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart YW Robot (LCM1602) LCD Display +// +//#define LCD_I2C_SAINSMART_YWROBOT + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + //#define U8GLIB_SSD1306 + #define U8GLIB_SH1106 +#endif + +// +// CONTROLLER TYPE: Shift register panels +// +// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// M240 Triggers a camera by emulating a Canon RC-1 Remote +// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ +//#define PHOTOGRAPH_PIN 23 + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder. +//#define BARICUDA + +//define BlinkM/CyzRgb Support +//#define BLINKM + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * + * *** CAUTION *** + * LED Strips require a MOFSET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * *** CAUTION *** + * + */ +//#define RGB_LED +//#define RGBW_LED +#if ENABLED(RGB_LED) || ENABLED(RGBW_LED) + #define RGB_LED_R_PIN 34 + #define RGB_LED_G_PIN 43 + #define RGB_LED_B_PIN 35 + #define RGB_LED_W_PIN -1 +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) + #define PRINTER_EVENT_LEDS +#endif + +/*********************************************************************\ +* R/C SERVO support +* Sponsored by TrinityLabs, Reworked by codexmas +**********************************************************************/ + +// Number of servos +// +// If you select a configuration below, this will receive a default value and does not need to be set manually +// set it manually if you have more servos than extruders and wish to manually control some +// leaving it undefined or defining as 0 will disable the servo subsystem +// If unsure, leave commented / disabled +// +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY 300 + +// Servo deactivation +// +// With this option servos are powered only during movement, then turned off to prevent jitter. +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +#endif // CONFIGURATION_H diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h new file mode 100644 index 0000000000..a8ffa080f6 --- /dev/null +++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -0,0 +1,1137 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#ifndef CONFIGURATION_ADV_H +#define CONFIGURATION_ADV_H + +/** + * + * *********************************** + * ** ATTENTION TO ALL DEVELOPERS ** + * *********************************** + * + * You must increment this version number for every significant change such as, + * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option. + * + * Note: Update also Version.h ! + */ +#define CONFIGURATION_ADV_H_VERSION 010100 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + /** + * Whenever an M104 or M109 increases the target temperature the firmware will wait for the + * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE + * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109, + * but only if the current temperature is far enough below the target for a reliable test. + * + * If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE + * WATCH_TEMP_INCREASE should not be below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * Whenever an M140 or M190 increases the target temperature the firmware will wait for the + * WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE + * degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190, + * but only if the current temperature is far enough below the target for a reliable test. + * + * If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease + * WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.) + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // this adds an experimental additional term to the heating power, proportional to the extrusion speed. + // if Kc is chosen well, the additional required power due to increased melting should be compensated. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +//Show Temperature ADC value +//The M105 command return, besides traditional information, the ADC value read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m + #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm +#endif + +// @section temperature + +//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements. +//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET" +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 + +//This is for controlling a fan to cool down the stepper drivers +//it will turn on when any driver is enabled +//and turn off after the set amount of seconds from last driver being disabled again +#define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller (-1 to disable) +#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run +#define CONTROLLERFAN_SPEED 255 // == full speed + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +// This defines the minimal speed for the main fan, run in PWM mode +// to enable uncomment and set minimal PWM speed for reliable running (1-255) +// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM +//#define FAN_MIN_PWM 50 + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed + +// Define a pin to turn case light on/off +//#define CASE_LIGHT_PIN 4 +#if PIN_EXISTS(CASE_LIGHT) + #define INVERT_CASE_LIGHT false // Set to true if HIGH is the OFF state (active low) + //#define CASE_LIGHT_DEFAULT_ON // Uncomment to set default state to on + //#define MENU_ITEM_CASE_LIGHT // Uncomment to have a Case Light On / Off entry in main menu +#endif + +//=========================================================================== +//============================ Mechanical Settings ========================== +//=========================================================================== + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Dual X Steppers +// Uncomment this option to drive two X axis motors. +// The next unused E driver will be assigned to the second X stepper. +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + // Set true if the two X motors need to rotate in opposite directions + #define INVERT_X2_VS_X_DIR true +#endif + +// Dual Y Steppers +// Uncomment this option to drive two Y axis motors. +// The next unused E driver will be assigned to the second Y stepper. +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + // Set true if the two Y motors need to rotate in opposite directions + #define INVERT_Y2_VS_Y_DIR true +#endif + +// A single Z stepper driver is usually used to drive 2 stepper motors. +// Uncomment this option to use a separate stepper driver for each Z axis motor. +// The next unused E driver will be assigned to the second Z stepper. +//#define Z_DUAL_STEPPER_DRIVERS + +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + + // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // There is also an implementation of M666 (software endstops adjustment) to this feature. + // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. + // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. + // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive. + // Play a little bit with small adjustments (0.5mm) and check the behaviour. + // The M119 (endstops report) will start reporting the Z2 Endstop as well. + + //#define Z_DUAL_ENDSTOPS + + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine/test this value + #endif + +#endif // Z_DUAL_STEPPER_DRIVERS + +// Enable this for dual x-carriage printers. +// A dual x-carriage design has the advantage that the inactive extruder can be parked which +// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage +// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug. +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + // Configuration for second X-carriage + // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop; + // the second x-carriage always homes to the maximum endstop. + #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage + #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // There are a few selectable movement modes for dual x-carriages using M605 S + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE + + // Default settings in "Auto-park Mode" + #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder + #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif //DUAL_X_CARRIAGE + +// @section homing + +//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again: +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 5 // deltas need the same for all three axes +#define HOMING_BUMP_DIVISOR {10, 10, 10} // Re-Bump Speed Divisor (Divides the Homing Feedrate) +//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially. + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// @section machine + +#define AXIS_RELATIVE_MODES {false, false, false, false} + +// Allow duplication mode with a basic dual-nozzle extruder +//#define DUAL_NOZZLE_DUPLICATION_MODE + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 60 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +// @section lcd + +#if ENABLED(ULTIPANEL) + #define MANUAL_FEEDRATE_XYZ 50*60 + #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +// (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) +//#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec) + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps +#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro +//#define DIGIPOT_I2C +//#define DIGIPOT_MCP4018 +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 +// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS +#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO + +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== + +#if ENABLED(DELTA_AUTO_CALIBRATION) + /** + * Set the height short (H-10) with M665 Hx.xx. + * Set the delta_radius offset (R-5, R-10, R+5, R+10) with M665 Rx.xx. + * Run G33 Cx V3 (C2, C-2) with different values for C and R + * Take the average for R_FACTOR and maximum for H_FACTOR. + * Run the tests with default values!!! + */ + //#define DELTA_CALIBRATE_EXPERT_MODE + + // Remove the comments of the folling 2 lines to overide default values + #define H_FACTOR 1.02 // 1.0 < H_FACTOR < 1.11, default 1.00 + #define R_FACTOR -3.95 // -6.7 < R_FACTOR < -2.25, default -2.25 +#endif + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly +#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value +#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value + +//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ +#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again + +// @section lcd + +// Include a page of printer information in the LCD Main Menu +//#define LCD_INFO_MENU + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers? + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place. + + #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order. + // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that. + // using: + //#define MENU_ADDAUTOSTART + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #endif + + // Show a progress bar on HD44780 LCDs for SD printing + //#define LCD_PROGRESS_BAR + + #if ENABLED(LCD_PROGRESS_BAR) + // Amount of time (ms) to show the bar + #define PROGRESS_BAR_BAR_TIME 2000 + // Amount of time (ms) to show the status message + #define PROGRESS_BAR_MSG_TIME 3000 + // Amount of time (ms) to retain the status message (0=forever) + #define PROGRESS_MSG_EXPIRE 0 + // Enable this to show messages for MSG_TIME then hide them + //#define PROGRESS_MSG_ONCE + // Add a menu item to test the progress bar: + //#define LCD_PROGRESS_BAR_TEST + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // This option allows you to abort SD printing when any endstop is triggered. + // This feature must be enabled with "M540 S1" or from the LCD menu. + // To have any effect, endstops must be enabled during SD printing. + //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED + +#endif // SDSUPPORT + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if ENABLED(DOGLCD) + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 +#endif // DOGLCD + +// @section safety + +// The hardware watchdog should reset the microcontroller disabling all outputs, +// in case the firmware gets stuck and doesn't do temperature regulation. +#define USE_WATCHDOG + +#if ENABLED(USE_WATCHDOG) + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +//#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping + //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. +#endif + +// @section extruder + +// extruder advance constant (s2/mm3) +// +// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2 +// +// Hooke's law says: force = k * distance +// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant +// so: v ^ 2 is proportional to number of steps we advance the extruder +//#define ADVANCE + +#if ENABLED(ADVANCE) + #define EXTRUDER_ADVANCE_K .0 + #define D_FILAMENT 2.85 +#endif + +/** + * Implementation of linear pressure control + * + * Assumption: advance = k * (delta velocity) + * K=0 means advance disabled. + * See Marlin documentation for calibration instructions. + */ +//#define LIN_ADVANCE + +#if ENABLED(LIN_ADVANCE) + #define LIN_ADVANCE_K 75 + + /** + * Some Slicers produce Gcode with randomly jumping extrusion widths occasionally. + * For example within a 0.4mm perimeter it may produce a single segment of 0.05mm width. + * While this is harmless for normal printing (the fluid nature of the filament will + * close this very, very tiny gap), it throws off the LIN_ADVANCE pressure adaption. + * + * For this case LIN_ADVANCE_E_D_RATIO can be used to set the extrusion:distance ratio + * to a fixed value. Note that using a fixed ratio will lead to wrong nozzle pressures + * if the slicer is using variable widths or layer heights within one print! + * + * This option sets the default E:D ratio at startup. Use `M905` to override this value. + * + * Example: `M905 W0.4 H0.2 D1.75`, where: + * - W is the extrusion width in mm + * - H is the layer height in mm + * - D is the filament diameter in mm + * + * Set to 0 to auto-detect the ratio based on given Gcode G1 print moves. + * + * Slic3r (including Prusa Slic3r) produces Gcode compatible with the automatic mode. + * Cura (as of this writing) may produce Gcode incompatible with the automatic mode. + */ + #define LIN_ADVANCE_E_D_RATIO 0 // The calculated ratio (or 0) according to the formula W * H / ((D / 2) ^ 2 * PI) + // Example: 0.4 * 0.2 / ((1.75 / 2) ^ 2 * PI) = 0.033260135 +#endif + +// @section leveling + +// Default mesh area is an area with an inset margin on the print area. +// Below are the macros that are used to define the borders for the mesh area, +// made available here for specialized needs, ie dual extruder setup. +#if ENABLED(MESH_BED_LEVELING) + #define MESH_MIN_X (X_MIN_POS + MESH_INSET) + #define MESH_MAX_X (X_MAX_POS - (MESH_INSET)) + #define MESH_MIN_Y (Y_MIN_POS + MESH_INSET) + #define MESH_MAX_Y (Y_MAX_POS - (MESH_INSET)) +#elif ENABLED(AUTO_BED_LEVELING_UBL) + #define UBL_MESH_MIN_X (X_MIN_POS + UBL_MESH_INSET) + #define UBL_MESH_MAX_X (X_MAX_POS - (UBL_MESH_INSET)) + #define UBL_MESH_MIN_Y (Y_MIN_POS + UBL_MESH_INSET) + #define UBL_MESH_MAX_Y (Y_MAX_POS - (UBL_MESH_INSET)) +#endif + +// @section extras + +// Arc interpretation settings: +#define ARC_SUPPORT // Disabling this saves ~2738 bytes +#define MM_PER_ARC_SEGMENT 1 +#define N_ARC_CORRECTION 25 + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +// G38.2 and G38.3 Probe Target +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +// The minimum pulse width (in µs) for stepping a stepper. +// Set this if you find stepping unreliable, or if using a very fast CPU. +#define MINIMUM_STEPPER_PULSE 0 // (µs) The smallest stepper pulse allowed + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transfer Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// @section fwretract + +// Firmware based and LCD controlled retract +// M207 and M208 can be used to define parameters for the retraction. +// The retraction can be called by the slicer using G10 and G11 +// until then, intended retractions can be detected by moves that only extrude and the direction. +// the moves are than replaced by the firmware controlled ones. + +//#define FWRETRACT //ONLY PARTIALLY TESTED +#if ENABLED(FWRETRACT) + #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt + #define RETRACT_LENGTH 3 //default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s) + #define RETRACT_ZLIFT 0 //default retract Z-lift + #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) +#endif + +/** + * Filament Change + * Experimental filament change support. + * Adds the GCode M600 for initiating filament change. + * + * Requires an LCD display. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define FILAMENT_CHANGE_FEATURE +#if ENABLED(FILAMENT_CHANGE_FEATURE) + #define FILAMENT_CHANGE_X_POS 3 // X position of hotend + #define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend + #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift) + #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) + #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) + #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s + #define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm + // It is a short retract used immediately after print interrupt before move to filament exchange position + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm + // Longer length for bowden printers to unload filament from whole bowden tube, + // shorter length for printers without bowden to unload filament from extruder only, + // 0 to disable unloading for manual unloading + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm + // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, + // Short or zero length for printers without bowden where loading is not used + #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend, + // 0 to disable for manual extrusion + // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, + // or until outcoming filament color is not clear for filament color change + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. + //#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume +#endif + +// @section tmc + +/** + * Enable this section if you have TMC26X motor drivers. + * You will need to import the TMC26XStepper library into the Arduino IDE for this + * (https://github.com/trinamic/TMC26XStepper.git) + */ +//#define HAVE_TMCDRIVER + +#if ENABLED(HAVE_TMCDRIVER) + + //#define X_IS_TMC + //#define X2_IS_TMC + //#define Y_IS_TMC + //#define Y2_IS_TMC + //#define Z_IS_TMC + //#define Z2_IS_TMC + //#define E0_IS_TMC + //#define E1_IS_TMC + //#define E2_IS_TMC + //#define E3_IS_TMC + //#define E4_IS_TMC + + #define X_MAX_CURRENT 1000 // in mA + #define X_SENSE_RESISTOR 91 // in mOhms + #define X_MICROSTEPS 16 // number of microsteps + + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + +#endif + +// @section TMC2130 + +/** + * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers. + * + * You'll also need the TMC2130Stepper Arduino library + * (https://github.com/teemuatlut/TMC2130Stepper). + * + * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to + * the hardware SPI interface on your board and define the required CS pins + * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + */ +//#define HAVE_TMC2130 + +#if ENABLED(HAVE_TMC2130) + #define STEALTHCHOP + + /** + * Let Marlin automatically control stepper current. + * This is still an experimental feature. + * Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered, + * then decrease current by CURRENT_STEP until temperature prewarn is cleared. + * Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX + */ + //#define AUTOMATIC_CURRENT_CONTROL + #define CURRENT_STEP 50 // [mA] + #define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak + + // CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY + //#define X_IS_TMC2130 + //#define X2_IS_TMC2130 + //#define Y_IS_TMC2130 + //#define Y2_IS_TMC2130 + //#define Z_IS_TMC2130 + //#define Z2_IS_TMC2130 + //#define E0_IS_TMC2130 + //#define E1_IS_TMC2130 + //#define E2_IS_TMC2130 + //#define E3_IS_TMC2130 + //#define E4_IS_TMC2130 + + /** + * Stepper driver settings + */ + + #define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130 + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256 + + #define X_MAX_CURRENT 1000 // rms current in mA + #define X_MICROSTEPS 16 // FULLSTEP..256 + #define X_CHIP_SELECT 40 // Pin + + #define Y_MAX_CURRENT 1000 + #define Y_MICROSTEPS 16 + #define Y_CHIP_SELECT 42 + + #define Z_MAX_CURRENT 1000 + #define Z_MICROSTEPS 16 + #define Z_CHIP_SELECT 65 + + //#define X2_MAX_CURRENT 1000 + //#define X2_MICROSTEPS 16 + //#define X2_CHIP_SELECT -1 + + //#define Y2_MAX_CURRENT 1000 + //#define Y2_MICROSTEPS 16 + //#define Y2_CHIP_SELECT -1 + + //#define Z2_MAX_CURRENT 1000 + //#define Z2_MICROSTEPS 16 + //#define Z2_CHIP_SELECT -1 + + //#define E0_MAX_CURRENT 1000 + //#define E0_MICROSTEPS 16 + //#define E0_CHIP_SELECT -1 + + //#define E1_MAX_CURRENT 1000 + //#define E1_MICROSTEPS 16 + //#define E1_CHIP_SELECT -1 + + //#define E2_MAX_CURRENT 1000 + //#define E2_MICROSTEPS 16 + //#define E2_CHIP_SELECT -1 + + //#define E3_MAX_CURRENT 1000 + //#define E3_MICROSTEPS 16 + //#define E3_CHIP_SELECT -1 + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMC2130Stepper + * + * Example: + * #define TMC2130_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperX.interpolate(0); \ + * } + */ + #define TMC2130_ADV() { } + +#endif // ENABLED(HAVE_TMC2130) + +// @section L6470 + +/** + * Enable this section if you have L6470 motor drivers. + * You need to import the L6470 library into the Arduino IDE for this. + * (https://github.com/ameyer/Arduino-L6470) + */ + +//#define HAVE_L6470DRIVER +#if ENABLED(HAVE_L6470DRIVER) + + //#define X_IS_L6470 + //#define X2_IS_L6470 + //#define Y_IS_L6470 + //#define Y2_IS_L6470 + //#define Z_IS_L6470 + //#define Z2_IS_L6470 + //#define E0_IS_L6470 + //#define E1_IS_L6470 + //#define E2_IS_L6470 + //#define E3_IS_L6470 + //#define E4_IS_L6470 + + #define X_MICROSTEPS 16 // number of microsteps + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high + #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off + #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall + + #define X2_MICROSTEPS 16 + #define X2_K_VAL 50 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + + #define Y_MICROSTEPS 16 + #define Y_K_VAL 50 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + + #define Y2_MICROSTEPS 16 + #define Y2_K_VAL 50 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + + #define Z_MICROSTEPS 16 + #define Z_K_VAL 50 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + + #define Z2_MICROSTEPS 16 + #define Z2_K_VAL 50 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + + #define E0_MICROSTEPS 16 + #define E0_K_VAL 50 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + + #define E1_MICROSTEPS 16 + #define E1_K_VAL 50 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + + #define E2_MICROSTEPS 16 + #define E2_K_VAL 50 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + + #define E3_MICROSTEPS 16 + #define E3_K_VAL 50 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + + #define E4_MICROSTEPS 16 + #define E4_K_VAL 50 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + +#endif + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +/** + * Auto-report temperatures with M155 S + */ +//#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +//#define EXTENDED_CAPABILITIES_REPORT + +/** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ +//#define VOLUMETRIC_DEFAULT_ON + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +#endif // CONFIGURATION_ADV_H diff --git a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h similarity index 98% rename from Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h rename to Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h index c8d085fadb..ce332e6e46 100644 --- a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h @@ -1,4 +1,4 @@ -/** +/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== @@ -463,16 +463,24 @@ // Horizontal distance bridged by diagonal push rods when effector is centered. #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) + // height from z=0.00 to home position + #define DELTA_HEIGHT 280 // get this value from auto calibrate + // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). #define DELTA_PRINTABLE_RADIUS 85.0 // Delta calibration menu // uncomment to add three points calibration menu option. // See http://minow.blogspot.com/index.html#4918805519571907051 - // If needed, adjust the X, Y, Z calibration coordinates - // in ultralcd.cpp@lcd_delta_calibrate_menu() //#define DELTA_CALIBRATION_MENU + // G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results) + //#define DELTA_AUTO_CALIBRATION + #if ENABLED(DELTA_AUTO_CALIBRATION) + #define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (1-4) + #define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 15) // set the radius for the calibration probe points + #endif + // After homing move down to a height where XY movement is unconstrained //#define DELTA_HOME_TO_SAFE_ZONE @@ -1080,7 +1088,7 @@ // For DELTA this is the top-center of the Cartesian print volume. //#define MANUAL_X_HOME_POS 0 //#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS (286.5 - 6.5) // Distance between the nozzle to printbed after homing +#define MANUAL_Z_HOME_POS DELTA_HEIGHT // Distance between the nozzle to printbed after homing // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. // diff --git a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h similarity index 98% rename from Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h rename to Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h index 6faad15106..6ee202ae09 100644 --- a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -431,6 +431,25 @@ // Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS #define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== + +#if ENABLED(DELTA_AUTO_CALIBRATION) + /** + * Set the height short (H-10) with M665 Hx.xx. + * Set the delta_radius offset (R-5, R-10, R+5, R+10) with M665 Rx.xx. + * Run G33 Cx V3 (C2, C-2) with different values for C and R + * Take the average for R_FACTOR and maximum for H_FACTOR. + * Run the tests with default values!!! + */ + //#define DELTA_CALIBRATE_EXPERT_MODE + + // Remove the comments of the folling 2 lines to overide default values + #define H_FACTOR 1.02 // 1.0 < H_FACTOR < 1.11, default 1.00 + #define R_FACTOR -3.95 // -6.7 < R_FACTOR < -2.25, default -2.25 +#endif + //=========================================================================== //=============================Additional Features=========================== //=========================================================================== diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 3d088639b1..22477b4ee0 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -1,4 +1,4 @@ -/** +/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== @@ -453,6 +453,9 @@ // Horizontal distance bridged by diagonal push rods when effector is centered. #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) + // height from z=0.00 to home position + #define DELTA_HEIGHT 250 // get this value from auto calibrate + // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). #define DELTA_PRINTABLE_RADIUS 140.0 @@ -460,6 +463,13 @@ // See http://minow.blogspot.com/index.html#4918805519571907051 //#define DELTA_CALIBRATION_MENU + // G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results) + //#define DELTA_AUTO_CALIBRATION + #if ENABLED(DELTA_AUTO_CALIBRATION) + #define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (1-4) + #define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 15) // set the radius for the calibration probe points + #endif + // After homing move down to a height where XY movement is unconstrained #define DELTA_HOME_TO_SAFE_ZONE @@ -1067,7 +1077,7 @@ // For DELTA this is the top-center of the Cartesian print volume. //#define MANUAL_X_HOME_POS 0 //#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 250 // Distance between the nozzle to printbed after homing +#define MANUAL_Z_HOME_POS DELTA_HEIGHT // Distance between the nozzle to printbed after homing // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. // diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index b95998e397..5ea04ce0ae 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -439,12 +439,13 @@ /** * Set the height short (H-10) with M665 Hx.xx. * Set the delta_radius offset (R-5, R-10, R+5, R+10) with M665 Rx.xx. - * Run G33 Cx V3 with different values (C2, C-2). + * Run G33 Cx V3 (C2, C-2) with different values for C and R * Take the average for R_FACTOR and maximum for H_FACTOR. - * If R_FACTOR is too low accuracy is reduced. Too high reduces iteration speed. * Run the tests with default values!!! */ //#define DELTA_CALIBRATE_EXPERT_MODE + + // Remove the comments of the folling 2 lines to overide default values //#define H_FACTOR 1.02 // 1.0 < H_FACTOR < 1.11, default 1.00 //#define R_FACTOR -3.95 // -6.7 < R_FACTOR < -2.25, default -2.25 #endif @@ -694,7 +695,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 5a47dd7588..205236cb98 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -1,4 +1,4 @@ -/** +/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== @@ -453,6 +453,9 @@ // Horizontal distance bridged by diagonal push rods when effector is centered. #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) + // height from z=0.00 to home position + #define DELTA_HEIGHT 250 // get this value from auto calibrate + // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). #define DELTA_PRINTABLE_RADIUS 90.0 @@ -460,6 +463,13 @@ // See http://minow.blogspot.com/index.html#4918805519571907051 //#define DELTA_CALIBRATION_MENU + // G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results) + //#define DELTA_AUTO_CALIBRATION + #if ENABLED(DELTA_AUTO_CALIBRATION) + #define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (1-4) + #define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 15) // set the radius for the calibration probe points + #endif + // After homing move down to a height where XY movement is unconstrained #define DELTA_HOME_TO_SAFE_ZONE @@ -1063,7 +1073,7 @@ // For DELTA this is the top-center of the Cartesian print volume. //#define MANUAL_X_HOME_POS 0 //#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 250 // Distance between the nozzle to printbed after homing +#define MANUAL_Z_HOME_POS DELTA_HEIGHT // Distance between the nozzle to printbed after homing // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. // diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index b95998e397..5ea04ce0ae 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -439,12 +439,13 @@ /** * Set the height short (H-10) with M665 Hx.xx. * Set the delta_radius offset (R-5, R-10, R+5, R+10) with M665 Rx.xx. - * Run G33 Cx V3 with different values (C2, C-2). + * Run G33 Cx V3 (C2, C-2) with different values for C and R * Take the average for R_FACTOR and maximum for H_FACTOR. - * If R_FACTOR is too low accuracy is reduced. Too high reduces iteration speed. * Run the tests with default values!!! */ //#define DELTA_CALIBRATE_EXPERT_MODE + + // Remove the comments of the folling 2 lines to overide default values //#define H_FACTOR 1.02 // 1.0 < H_FACTOR < 1.11, default 1.00 //#define R_FACTOR -3.95 // -6.7 < R_FACTOR < -2.25, default -2.25 #endif @@ -694,7 +695,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index 71f8f62edc..aae0e18a66 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -1,4 +1,4 @@ -/** +/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * @@ -74,8 +74,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== @@ -440,6 +440,9 @@ // Horizontal distance bridged by diagonal push rods when effector is centered. #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) + // height from z=0.00 to home position + #define DELTA_HEIGHT 277 // get this value from auto calibrate + // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). #define DELTA_PRINTABLE_RADIUS 127.0 @@ -447,6 +450,13 @@ // See http://minow.blogspot.com/index.html#4918805519571907051 //#define DELTA_CALIBRATION_MENU + // G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results) + //#define DELTA_AUTO_CALIBRATION + #if ENABLED(DELTA_AUTO_CALIBRATION) + #define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (1-4) + #define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 15) // set the radius for the calibration probe points + #endif + // After homing move down to a height where XY movement is unconstrained #define DELTA_HOME_TO_SAFE_ZONE @@ -1071,7 +1081,7 @@ // For DELTA this is the top-center of the Cartesian print volume. //#define MANUAL_X_HOME_POS 0 //#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 277 // Distance between the nozzle to printbed after homing +#define MANUAL_Z_HOME_POS DELTA_HEIGHT // Distance between the nozzle to printbed after homing // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. // diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h index c984b940fa..1613baeb8d 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h @@ -436,6 +436,26 @@ // Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS #define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== + +#if ENABLED(DELTA_AUTO_CALIBRATION) + /** + * Set the height short (H-10) with M665 Hx.xx. + * Set the delta_radius offset (R-5, R-10, R+5, R+10) with M665 Rx.xx. + * Run G33 Cx V3 (C2, C-2) with different values for C and R + * Take the average for R_FACTOR and maximum for H_FACTOR. + * Run the tests with default values!!! + */ + //#define DELTA_CALIBRATE_EXPERT_MODE + + // Remove the comments of the folling 2 lines to overide default values + //#define H_FACTOR 1.02 // 1.0 < H_FACTOR < 1.11, default 1.00 + //#define R_FACTOR -3.95 // -6.7 < R_FACTOR < -2.25, default -2.25 +#endif + + //=========================================================================== //=============================Additional Features=========================== //=========================================================================== @@ -681,7 +701,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index eb3e3e4309..f284c784cf 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -1,4 +1,4 @@ -/** +/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== @@ -458,6 +458,9 @@ // Horizontal distance bridged by diagonal push rods when effector is centered. #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET) + 1) + // height from z=0.00 to home position + #define DELTA_HEIGHT 380 // get this value from auto calibrate + // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). #define DELTA_PRINTABLE_RADIUS 140.0 @@ -465,6 +468,13 @@ // See http://minow.blogspot.com/index.html#4918805519571907051 //#define DELTA_CALIBRATION_MENU + // G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results) + //#define DELTA_AUTO_CALIBRATION + #if ENABLED(DELTA_AUTO_CALIBRATION) + #define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (1-4) + #define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 15) // set the radius for the calibration probe points + #endif + // After homing move down to a height where XY movement is unconstrained #define DELTA_HOME_TO_SAFE_ZONE @@ -1078,7 +1088,7 @@ // For DELTA this is the top-center of the Cartesian print volume. //#define MANUAL_X_HOME_POS 0 //#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 381.4 // Distance between the nozzle to printbed after homing +#define MANUAL_Z_HOME_POS DELTA_HEIGHT // Distance between the nozzle to printbed after homing // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. // diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h index d7fb200cb0..727768807b 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h @@ -1,4 +1,4 @@ -/** +/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * @@ -431,6 +431,25 @@ // Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS #define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== + +#if ENABLED(DELTA_AUTO_CALIBRATION) + /** + * Set the height short (H-10) with M665 Hx.xx. + * Set the delta_radius offset (R-5, R-10, R+5, R+10) with M665 Rx.xx. + * Run G33 Cx V3 (C2, C-2) with different values for C and R + * Take the average for R_FACTOR and maximum for H_FACTOR. + * Run the tests with default values!!! + */ + //#define DELTA_CALIBRATE_EXPERT_MODE + + // Remove the comments of the folling 2 lines to overide default values + //#define H_FACTOR 1.02 // 1.0 < H_FACTOR < 1.11, default 1.00 + //#define R_FACTOR -3.95 // -6.7 < R_FACTOR < -2.25, default -2.25 +#endif + //=========================================================================== //=============================Additional Features=========================== //=========================================================================== @@ -676,7 +695,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index ceb7951240..26445970bf 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index c22d6add27..11b8cf0978 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -674,7 +674,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index a6da3cb7a9..e95bbc15fe 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index c85d848d00..f5fd6eac40 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -674,7 +674,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) diff --git a/Marlin/example_configurations/wt150/Configuration.h b/Marlin/example_configurations/wt150/Configuration.h index 9740a45d71..996a82593d 100644 --- a/Marlin/example_configurations/wt150/Configuration.h +++ b/Marlin/example_configurations/wt150/Configuration.h @@ -70,8 +70,8 @@ //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. +// For Delta printers start with one of the configuration files in the +// example_configurations/delta directory and customize for your machine. // //=========================================================================== diff --git a/Marlin/example_configurations/wt150/Configuration_adv.h b/Marlin/example_configurations/wt150/Configuration_adv.h index 605eaee934..d8c93a21b3 100644 --- a/Marlin/example_configurations/wt150/Configuration_adv.h +++ b/Marlin/example_configurations/wt150/Configuration_adv.h @@ -677,7 +677,7 @@ //#define BEZIER_CURVE_SUPPORT // G38.2 and G38.3 Probe Target -// ENABLE PROBE_DOUBLE_TOUCH if you want G38 to double touch +// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch //#define G38_PROBE_TARGET #if ENABLED(G38_PROBE_TARGET) #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move) @@ -971,14 +971,14 @@ #endif // ENABLED(HAVE_TMC2130) +// @section L6470 + /** * Enable this section if you have L6470 motor drivers. * You need to import the L6470 library into the Arduino IDE for this. * (https://github.com/ameyer/Arduino-L6470) */ -// @section l6470 - //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) diff --git a/Marlin/language_en.h b/Marlin/language_en.h index e6c285a1aa..ffa0d66941 100644 --- a/Marlin/language_en.h +++ b/Marlin/language_en.h @@ -498,6 +498,12 @@ #ifndef MSG_DELTA_CALIBRATE_CENTER #define MSG_DELTA_CALIBRATE_CENTER _UxGT("Calibrate Center") #endif +#ifndef MSG_DELTA_AUTO_CALIBRATE + #define MSG_DELTA_AUTO_CALIBRATE _UxGT("Auto Calibration") +#endif +#ifndef MSG_DELTA_HEIGHT_CALIBRATE + #define MSG_DELTA_HEIGHT_CALIBRATE _UxGT("Set Delta Height") +#endif #ifndef MSG_INFO_MENU #define MSG_INFO_MENU _UxGT("About Printer") #endif diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index 165a397a68..4d92db3391 100755 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -817,7 +817,7 @@ void kill_screen(const char* lcd_msg) { * */ - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_M206_COMMAND /** * Set the home offset based on the current_position */ @@ -1672,7 +1672,7 @@ void kill_screen(const char* lcd_msg) { #endif - #if DISABLED(NO_WORKSPACE_OFFSETS) + #if HAS_M206_COMMAND // // Set Home Offsets // @@ -1770,14 +1770,20 @@ void kill_screen(const char* lcd_msg) { lcd_goto_screen(_lcd_calibrate_homing); } + #if ENABLED(DELTA_AUTO_CALIBRATION) + #define _DELTA_TOWER_MOVE_RADIUS DELTA_CALIBRATION_RADIUS + #else + #define _DELTA_TOWER_MOVE_RADIUS DELTA_PRINTABLE_RADIUS + #endif + // Move directly to the tower position with uninterpolated moves // If we used interpolated moves it would cause this to become re-entrant void _goto_tower_pos(const float &a) { current_position[Z_AXIS] = max(Z_HOMING_HEIGHT, Z_CLEARANCE_BETWEEN_PROBES) + (DELTA_PRINTABLE_RADIUS) / 5; line_to_current(Z_AXIS); - current_position[X_AXIS] = a < 0 ? X_HOME_POS : sin(a) * -(DELTA_PRINTABLE_RADIUS); - current_position[Y_AXIS] = a < 0 ? Y_HOME_POS : cos(a) * (DELTA_PRINTABLE_RADIUS); + current_position[X_AXIS] = a < 0 ? LOGICAL_X_POSITION(X_HOME_POS) : sin(a) * -(_DELTA_TOWER_MOVE_RADIUS); + current_position[Y_AXIS] = a < 0 ? LOGICAL_Y_POSITION(Y_HOME_POS) : cos(a) * (_DELTA_TOWER_MOVE_RADIUS); line_to_current(Z_AXIS); current_position[Z_AXIS] = 4.0; @@ -1797,6 +1803,10 @@ void kill_screen(const char* lcd_msg) { void lcd_delta_calibrate_menu() { START_MENU(); MENU_BACK(MSG_MAIN); + #if ENABLED(DELTA_AUTO_CALIBRATION) + MENU_ITEM(gcode, MSG_DELTA_AUTO_CALIBRATE, PSTR("G33 C")); + MENU_ITEM(gcode, MSG_DELTA_HEIGHT_CALIBRATE, PSTR("G33 C1")); + #endif MENU_ITEM(submenu, MSG_AUTO_HOME, _lcd_delta_calibrate_home); if (axis_homed[Z_AXIS]) { MENU_ITEM(submenu, MSG_DELTA_CALIBRATE_X, _goto_tower_x); diff --git a/buildroot/share/git/firstpush b/buildroot/share/git/firstpush index e8eef06da8..0d8e71c796 100755 --- a/buildroot/share/git/firstpush +++ b/buildroot/share/git/firstpush @@ -1,3 +1,26 @@ #!/usr/bin/env bash +# +# firstpush +# +# Push a branch to 'origin' and open the +# commit log to watch Travis CI progress. +# -git push --set-upstream origin `git branch | grep \* | sed 's/\* //g'` \ No newline at end of file +MFINFO=$(mfinfo) || exit +IFS=' ' read -a INFO <<< "$MFINFO" +FORK=${INFO[1]} +REPO=${INFO[2]} +BRANCH=${INFO[4]} + +git push --set-upstream origin $BRANCH + +TOOL=$(which gnome-open xdg-open open | awk '{ print $1 }') +URL="https://github.com/$FORK/$REPO/commits/$BRANCH" + +if [ -z "$TOOL" ]; then + echo "Can't find a tool to open the URL:" + echo $URL +else + echo "Viewing commits on $BRANCH..." + "$TOOL" "$URL" +fi