Clean up GCode command short comments
This commit is contained in:
Scott Lahteine
parent
47bd142b29
commit
e6164d254d
@ -5961,7 +5961,8 @@ inline void gcode_M206() {
|
||||
|
||||
/**
|
||||
* M209: Enable automatic retract (M209 S1)
|
||||
* detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
|
||||
* For slicers that don't support G10/11, reversed extrude-only
|
||||
* moves will be classified as retraction.
|
||||
*/
|
||||
inline void gcode_M209() {
|
||||
if (code_seen('S')) {
|
||||
@ -7597,90 +7598,83 @@ void process_next_command() {
|
||||
|
||||
case 'M': switch (codenum) {
|
||||
#if ENABLED(ULTIPANEL) || ENABLED(EMERGENCY_PARSER)
|
||||
case 0: // M0 - Unconditional stop - Wait for user button press on LCD
|
||||
case 1: // M1 - Conditional stop - Wait for user button press on LCD
|
||||
case 0: // M0: Unconditional stop - Wait for user button press on LCD
|
||||
case 1: // M1: Conditional stop - Wait for user button press on LCD
|
||||
gcode_M0_M1();
|
||||
break;
|
||||
#endif // ULTIPANEL
|
||||
|
||||
case 17:
|
||||
case 17: // M17: Enable all stepper motors
|
||||
gcode_M17();
|
||||
break;
|
||||
|
||||
#if ENABLED(SDSUPPORT)
|
||||
case 20: // M20 - list SD card
|
||||
case 20: // M20: list SD card
|
||||
gcode_M20(); break;
|
||||
case 21: // M21 - init SD card
|
||||
case 21: // M21: init SD card
|
||||
gcode_M21(); break;
|
||||
case 22: //M22 - release SD card
|
||||
case 22: // M22: release SD card
|
||||
gcode_M22(); break;
|
||||
case 23: //M23 - Select file
|
||||
case 23: // M23: Select file
|
||||
gcode_M23(); break;
|
||||
case 24: //M24 - Start SD print
|
||||
case 24: // M24: Start SD print
|
||||
gcode_M24(); break;
|
||||
case 25: //M25 - Pause SD print
|
||||
case 25: // M25: Pause SD print
|
||||
gcode_M25(); break;
|
||||
case 26: //M26 - Set SD index
|
||||
case 26: // M26: Set SD index
|
||||
gcode_M26(); break;
|
||||
case 27: //M27 - Get SD status
|
||||
case 27: // M27: Get SD status
|
||||
gcode_M27(); break;
|
||||
case 28: //M28 - Start SD write
|
||||
case 28: // M28: Start SD write
|
||||
gcode_M28(); break;
|
||||
case 29: //M29 - Stop SD write
|
||||
case 29: // M29: Stop SD write
|
||||
gcode_M29(); break;
|
||||
case 30: //M30 <filename> Delete File
|
||||
case 30: // M30 <filename> Delete File
|
||||
gcode_M30(); break;
|
||||
case 32: //M32 - Select file and start SD print
|
||||
case 32: // M32: Select file and start SD print
|
||||
gcode_M32(); break;
|
||||
|
||||
#if ENABLED(LONG_FILENAME_HOST_SUPPORT)
|
||||
case 33: //M33 - Get the long full path to a file or folder
|
||||
case 33: // M33: Get the long full path to a file or folder
|
||||
gcode_M33(); break;
|
||||
#endif // LONG_FILENAME_HOST_SUPPORT
|
||||
#endif
|
||||
|
||||
case 928: //M928 - Start SD write
|
||||
case 928: // M928: Start SD write
|
||||
gcode_M928(); break;
|
||||
#endif //SDSUPPORT
|
||||
|
||||
case 31: //M31 take time since the start of the SD print or an M109 command
|
||||
gcode_M31();
|
||||
break;
|
||||
case 31: // M31: Report time since the start of SD print or last M109
|
||||
gcode_M31(); break;
|
||||
|
||||
case 42: //M42 -Change pin status via gcode
|
||||
gcode_M42();
|
||||
break;
|
||||
|
||||
#if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
|
||||
case 48: // M48 Z probe repeatability
|
||||
case 48: // M48: Z probe repeatability test
|
||||
gcode_M48();
|
||||
break;
|
||||
#endif // Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
case 75: // Start print timer
|
||||
gcode_M75();
|
||||
break;
|
||||
|
||||
case 76: // Pause print timer
|
||||
gcode_M76();
|
||||
break;
|
||||
|
||||
case 77: // Stop print timer
|
||||
gcode_M77();
|
||||
break;
|
||||
case 75: // M75: Start print timer
|
||||
gcode_M75(); break;
|
||||
case 76: // M76: Pause print timer
|
||||
gcode_M76(); break;
|
||||
case 77: // M77: Stop print timer
|
||||
gcode_M77(); break;
|
||||
|
||||
#if ENABLED(PRINTCOUNTER)
|
||||
case 78: // Show print statistics
|
||||
gcode_M78();
|
||||
break;
|
||||
case 78: // M78: Show print statistics
|
||||
gcode_M78(); break;
|
||||
#endif
|
||||
|
||||
#if ENABLED(M100_FREE_MEMORY_WATCHER)
|
||||
case 100:
|
||||
case 100: // M100: Free Memory Report
|
||||
gcode_M100();
|
||||
break;
|
||||
#endif
|
||||
|
||||
case 104: // M104
|
||||
case 104: // M104: Set hot end temperature
|
||||
gcode_M104();
|
||||
break;
|
||||
|
||||
@ -7714,21 +7708,21 @@ void process_next_command() {
|
||||
break;
|
||||
#endif
|
||||
|
||||
case 140: // M140: Set bed temp
|
||||
case 140: // M140: Set bed temperature
|
||||
gcode_M140();
|
||||
break;
|
||||
|
||||
case 105: // M105: Read current temperature
|
||||
case 105: // M105: Report current temperature
|
||||
gcode_M105();
|
||||
KEEPALIVE_STATE(NOT_BUSY);
|
||||
return; // "ok" already printed
|
||||
|
||||
case 109: // M109: Wait for temperature
|
||||
case 109: // M109: Wait for hotend temperature to reach target
|
||||
gcode_M109();
|
||||
break;
|
||||
|
||||
#if HAS_TEMP_BED
|
||||
case 190: // M190: Wait for bed heater to reach target
|
||||
case 190: // M190: Wait for bed temperature to reach target
|
||||
gcode_M190();
|
||||
break;
|
||||
#endif // HAS_TEMP_BED
|
||||
@ -7776,17 +7770,17 @@ void process_next_command() {
|
||||
gcode_M81();
|
||||
break;
|
||||
|
||||
case 82:
|
||||
case 82: // M83: Set E axis normal mode (same as other axes)
|
||||
gcode_M82();
|
||||
break;
|
||||
case 83:
|
||||
case 83: // M83: Set E axis relative mode
|
||||
gcode_M83();
|
||||
break;
|
||||
case 18: // (for compatibility)
|
||||
case 84: // M84
|
||||
case 18: // M18 => M84
|
||||
case 84: // M84: Disable all steppers or set timeout
|
||||
gcode_M18_M84();
|
||||
break;
|
||||
case 85: // M85
|
||||
case 85: // M85: Set inactivity stepper shutdown timeout
|
||||
gcode_M85();
|
||||
break;
|
||||
case 92: // M92: Set the steps-per-unit for one or more axes
|
||||
@ -7820,51 +7814,51 @@ void process_next_command() {
|
||||
#endif
|
||||
|
||||
#if ENABLED(TEMPERATURE_UNITS_SUPPORT)
|
||||
case 149:
|
||||
case 149: // M149: Set temperature units
|
||||
gcode_M149();
|
||||
break;
|
||||
#endif
|
||||
|
||||
#if ENABLED(BLINKM)
|
||||
|
||||
case 150: // M150
|
||||
case 150: // M150: Set the BlinkM LCD color
|
||||
gcode_M150();
|
||||
break;
|
||||
|
||||
#endif //BLINKM
|
||||
#endif // BLINKM
|
||||
|
||||
#if ENABLED(EXPERIMENTAL_I2CBUS)
|
||||
|
||||
case 155:
|
||||
case 155: // M155: Send data to an i2c slave
|
||||
gcode_M155();
|
||||
break;
|
||||
|
||||
case 156:
|
||||
case 156: // M156: Request data from an i2c slave
|
||||
gcode_M156();
|
||||
break;
|
||||
|
||||
#endif //EXPERIMENTAL_I2CBUS
|
||||
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
case 163: // M163 S<int> P<float> set weight for a mixing extruder
|
||||
case 163: // M163: Set a component weight for mixing extruder
|
||||
gcode_M163();
|
||||
break;
|
||||
#if MIXING_VIRTUAL_TOOLS > 1
|
||||
case 164: // M164 S<int> save current mix as a virtual extruder
|
||||
case 164: // M164: Save current mix as a virtual extruder
|
||||
gcode_M164();
|
||||
break;
|
||||
#endif
|
||||
#if ENABLED(DIRECT_MIXING_IN_G1)
|
||||
case 165: // M165 [ABCDHI]<float> set multiple mix weights
|
||||
case 165: // M165: Set multiple mix weights
|
||||
gcode_M165();
|
||||
break;
|
||||
#endif
|
||||
#endif
|
||||
|
||||
case 200: // M200 D<diameter> Set filament diameter and set E axis units to cubic. (Use S0 to revert to linear units.)
|
||||
case 200: // M200: Set filament diameter, E to cubic units
|
||||
gcode_M200();
|
||||
break;
|
||||
case 201: // M201
|
||||
case 201: // M201: Set max acceleration for print moves (units/s^2)
|
||||
gcode_M201();
|
||||
break;
|
||||
#if 0 // Not used for Sprinter/grbl gen6
|
||||
@ -7872,180 +7866,180 @@ void process_next_command() {
|
||||
gcode_M202();
|
||||
break;
|
||||
#endif
|
||||
case 203: // M203 max feedrate units/sec
|
||||
case 203: // M203: Set max feedrate (units/sec)
|
||||
gcode_M203();
|
||||
break;
|
||||
case 204: // M204 acclereration S normal moves T filmanent only moves
|
||||
case 204: // M204: Set acceleration
|
||||
gcode_M204();
|
||||
break;
|
||||
case 205: //M205 advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk
|
||||
case 205: //M205: Set advanced settings
|
||||
gcode_M205();
|
||||
break;
|
||||
case 206: // M206 additional homing offset
|
||||
case 206: // M206: Set home offsets
|
||||
gcode_M206();
|
||||
break;
|
||||
|
||||
#if ENABLED(DELTA)
|
||||
case 665: // M665 set delta configurations L<diagonal_rod> R<delta_radius> S<segments_per_sec>
|
||||
case 665: // M665: Set delta configurations
|
||||
gcode_M665();
|
||||
break;
|
||||
#endif
|
||||
|
||||
#if ENABLED(DELTA) || ENABLED(Z_DUAL_ENDSTOPS)
|
||||
case 666: // M666 set delta / dual endstop adjustment
|
||||
case 666: // M666: Set delta or dual endstop adjustment
|
||||
gcode_M666();
|
||||
break;
|
||||
#endif
|
||||
|
||||
#if ENABLED(FWRETRACT)
|
||||
case 207: // M207 - Set Retract Length: S<length>, Feedrate: F<units/min>, and Z lift: Z<distance>
|
||||
case 207: // M207: Set Retract Length, Feedrate, and Z lift
|
||||
gcode_M207();
|
||||
break;
|
||||
case 208: // M208 - Set Recover (unretract) Additional (!) Length: S<length> and Feedrate: F<units/min>
|
||||
case 208: // M208: Set Recover (unretract) Additional Length and Feedrate
|
||||
gcode_M208();
|
||||
break;
|
||||
case 209: // M209 - Turn Automatic Retract Detection on/off: S<bool> (For slicers that don't support G10/11). Every normal extrude-only move will be classified as retract depending on the direction.
|
||||
case 209: // M209: Turn Automatic Retract Detection on/off
|
||||
gcode_M209();
|
||||
break;
|
||||
#endif // FWRETRACT
|
||||
|
||||
case 211: // M211 - Enable, Disable, and/or Report software endstops
|
||||
case 211: // M211: Enable, Disable, and/or Report software endstops
|
||||
gcode_M211();
|
||||
break;
|
||||
|
||||
#if HOTENDS > 1
|
||||
case 218: // M218 - Set a tool offset: T<index> X<offset> Y<offset>
|
||||
case 218: // M218: Set a tool offset
|
||||
gcode_M218();
|
||||
break;
|
||||
#endif
|
||||
|
||||
case 220: // M220 - Set Feedrate Percentage: S<percent> ("FR" on your LCD)
|
||||
case 220: // M220: Set Feedrate Percentage: S<percent> ("FR" on your LCD)
|
||||
gcode_M220();
|
||||
break;
|
||||
|
||||
case 221: // M221 - Set Flow Percentage: S<percent>
|
||||
case 221: // M221: Set Flow Percentage
|
||||
gcode_M221();
|
||||
break;
|
||||
|
||||
case 226: // M226 P<pin number> S<pin state>- Wait until the specified pin reaches the state required
|
||||
case 226: // M226: Wait until a pin reaches a state
|
||||
gcode_M226();
|
||||
break;
|
||||
|
||||
#if HAS_SERVOS
|
||||
case 280: // M280 - set servo position absolute. P: servo index, S: angle or microseconds
|
||||
case 280: // M280: Set servo position absolute
|
||||
gcode_M280();
|
||||
break;
|
||||
#endif // HAS_SERVOS
|
||||
|
||||
#if HAS_BUZZER
|
||||
case 300: // M300 - Play beep tone
|
||||
case 300: // M300: Play beep tone
|
||||
gcode_M300();
|
||||
break;
|
||||
#endif // HAS_BUZZER
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
case 301: // M301
|
||||
case 301: // M301: Set hotend PID parameters
|
||||
gcode_M301();
|
||||
break;
|
||||
#endif // PIDTEMP
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
case 304: // M304
|
||||
case 304: // M304: Set bed PID parameters
|
||||
gcode_M304();
|
||||
break;
|
||||
#endif // PIDTEMPBED
|
||||
|
||||
#if defined(CHDK) || HAS_PHOTOGRAPH
|
||||
case 240: // M240 Triggers a camera by emulating a Canon RC-1 : http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
case 240: // M240: Trigger a camera by emulating a Canon RC-1 : http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
gcode_M240();
|
||||
break;
|
||||
#endif // CHDK || PHOTOGRAPH_PIN
|
||||
|
||||
#if HAS_LCD_CONTRAST
|
||||
case 250: // M250 Set LCD contrast value: C<value> (value 0..63)
|
||||
case 250: // M250: Set LCD contrast
|
||||
gcode_M250();
|
||||
break;
|
||||
#endif // HAS_LCD_CONTRAST
|
||||
|
||||
#if ENABLED(PREVENT_COLD_EXTRUSION)
|
||||
case 302: // allow cold extrudes, or set the minimum extrude temperature
|
||||
case 302: // M302: Allow cold extrudes (set the minimum extrude temperature)
|
||||
gcode_M302();
|
||||
break;
|
||||
#endif // PREVENT_COLD_EXTRUSION
|
||||
|
||||
case 303: // M303 PID autotune
|
||||
case 303: // M303: PID autotune
|
||||
gcode_M303();
|
||||
break;
|
||||
|
||||
#if ENABLED(MORGAN_SCARA)
|
||||
case 360: // M360 SCARA Theta pos1
|
||||
case 360: // M360: SCARA Theta pos1
|
||||
if (gcode_M360()) return;
|
||||
break;
|
||||
case 361: // M361 SCARA Theta pos2
|
||||
case 361: // M361: SCARA Theta pos2
|
||||
if (gcode_M361()) return;
|
||||
break;
|
||||
case 362: // M362 SCARA Psi pos1
|
||||
case 362: // M362: SCARA Psi pos1
|
||||
if (gcode_M362()) return;
|
||||
break;
|
||||
case 363: // M363 SCARA Psi pos2
|
||||
case 363: // M363: SCARA Psi pos2
|
||||
if (gcode_M363()) return;
|
||||
break;
|
||||
case 364: // M364 SCARA Psi pos3 (90 deg to Theta)
|
||||
case 364: // M364: SCARA Psi pos3 (90 deg to Theta)
|
||||
if (gcode_M364()) return;
|
||||
break;
|
||||
#endif // SCARA
|
||||
|
||||
case 400: // M400 finish all moves
|
||||
case 400: // M400: Finish all moves
|
||||
gcode_M400();
|
||||
break;
|
||||
|
||||
#if HAS_BED_PROBE
|
||||
case 401:
|
||||
case 401: // M401: Deploy probe
|
||||
gcode_M401();
|
||||
break;
|
||||
case 402:
|
||||
case 402: // M402: Stow probe
|
||||
gcode_M402();
|
||||
break;
|
||||
#endif // HAS_BED_PROBE
|
||||
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
case 404: //M404 Enter the nominal filament width (3mm, 1.75mm ) N<3.0> or display nominal filament width
|
||||
case 404: // M404: Enter the nominal filament width (3mm, 1.75mm ) N<3.0> or display nominal filament width
|
||||
gcode_M404();
|
||||
break;
|
||||
case 405: //M405 Turn on filament sensor for control
|
||||
case 405: // M405: Turn on filament sensor for control
|
||||
gcode_M405();
|
||||
break;
|
||||
case 406: //M406 Turn off filament sensor for control
|
||||
case 406: // M406: Turn off filament sensor for control
|
||||
gcode_M406();
|
||||
break;
|
||||
case 407: //M407 Display measured filament diameter
|
||||
case 407: // M407: Display measured filament diameter
|
||||
gcode_M407();
|
||||
break;
|
||||
#endif // ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
|
||||
#if ENABLED(MESH_BED_LEVELING)
|
||||
case 420: // M420 Enable/Disable Mesh Bed Leveling
|
||||
case 420: // M420: Enable/Disable Mesh Bed Leveling
|
||||
gcode_M420();
|
||||
break;
|
||||
case 421: // M421 Set a Mesh Bed Leveling Z coordinate
|
||||
case 421: // M421: Set a Mesh Bed Leveling Z coordinate
|
||||
gcode_M421();
|
||||
break;
|
||||
#endif
|
||||
|
||||
case 428: // M428 Apply current_position to home_offset
|
||||
case 428: // M428: Apply current_position to home_offset
|
||||
gcode_M428();
|
||||
break;
|
||||
|
||||
case 500: // M500 Store settings in EEPROM
|
||||
case 500: // M500: Store settings in EEPROM
|
||||
gcode_M500();
|
||||
break;
|
||||
case 501: // M501 Read settings from EEPROM
|
||||
case 501: // M501: Read settings from EEPROM
|
||||
gcode_M501();
|
||||
break;
|
||||
case 502: // M502 Revert to default settings
|
||||
case 502: // M502: Revert to default settings
|
||||
gcode_M502();
|
||||
break;
|
||||
case 503: // M503 print settings currently in memory
|
||||
case 503: // M503: print settings currently in memory
|
||||
gcode_M503();
|
||||
break;
|
||||
|
||||
@ -8056,46 +8050,46 @@ void process_next_command() {
|
||||
#endif
|
||||
|
||||
#if HAS_BED_PROBE
|
||||
case 851: // Set Z Probe Z Offset
|
||||
case 851: // M851: Set Z Probe Z Offset
|
||||
gcode_M851();
|
||||
break;
|
||||
#endif // HAS_BED_PROBE
|
||||
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
case 600: //Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
||||
case 600: // M600: Pause for filament change
|
||||
gcode_M600();
|
||||
break;
|
||||
#endif // FILAMENT_CHANGE_FEATURE
|
||||
|
||||
#if ENABLED(DUAL_X_CARRIAGE)
|
||||
case 605:
|
||||
case 605: // M605: Set Dual X Carriage movement mode
|
||||
gcode_M605();
|
||||
break;
|
||||
#endif // DUAL_X_CARRIAGE
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
case 905: // M905 Set advance factor.
|
||||
case 905: // M905: Set advance K factor.
|
||||
gcode_M905();
|
||||
break;
|
||||
#endif
|
||||
|
||||
case 907: // M907 Set digital trimpot motor current using axis codes.
|
||||
case 907: // M907: Set digital trimpot motor current using axis codes.
|
||||
gcode_M907();
|
||||
break;
|
||||
|
||||
#if HAS_DIGIPOTSS || ENABLED(DAC_STEPPER_CURRENT)
|
||||
|
||||
case 908: // M908 Control digital trimpot directly.
|
||||
case 908: // M908: Control digital trimpot directly.
|
||||
gcode_M908();
|
||||
break;
|
||||
|
||||
#if ENABLED(DAC_STEPPER_CURRENT) // As with Printrbot RevF
|
||||
|
||||
case 909: // M909 Print digipot/DAC current value
|
||||
case 909: // M909: Print digipot/DAC current value
|
||||
gcode_M909();
|
||||
break;
|
||||
|
||||
case 910: // M910 Commit digipot/DAC value to external EEPROM
|
||||
case 910: // M910: Commit digipot/DAC value to external EEPROM
|
||||
gcode_M910();
|
||||
break;
|
||||
|
||||
@ -8105,11 +8099,11 @@ void process_next_command() {
|
||||
|
||||
#if HAS_MICROSTEPS
|
||||
|
||||
case 350: // M350 Set microstepping mode. Warning: Steps per unit remains unchanged. S code sets stepping mode for all drivers.
|
||||
case 350: // M350: Set microstepping mode. Warning: Steps per unit remains unchanged. S code sets stepping mode for all drivers.
|
||||
gcode_M350();
|
||||
break;
|
||||
|
||||
case 351: // M351 Toggle MS1 MS2 pins directly, S# determines MS1 or MS2, X# sets the pin high/low.
|
||||
case 351: // M351: Toggle MS1 MS2 pins directly, S# determines MS1 or MS2, X# sets the pin high/low.
|
||||
gcode_M351();
|
||||
break;
|
||||
|
||||
|
||||
@ -275,8 +275,6 @@
|
||||
#define DIO21_DDR DDRC
|
||||
#define DIO21_PWM NULL
|
||||
|
||||
|
||||
|
||||
#undef PB0
|
||||
#define PB0_PIN PINB0
|
||||
#define PB0_RPORT PINB
|
||||
|
||||
Loading…
Reference in New Issue
Block a user