Improved MANUAL_[XYZ]_HOME_POS
No need for `MANUAL_HOME_POSITIONS`. Just set each one as-needed to override the automatic behavior.
This commit is contained in:
parent
1734de4d4e
commit
ea5ac94804
@ -94,22 +94,29 @@
|
||||
#endif
|
||||
|
||||
/**
|
||||
* AUTOSET LOCATIONS OF LIMIT SWITCHES
|
||||
* Set the home position based on settings or manual overrides
|
||||
*/
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS) // Use manual limit switch locations
|
||||
#ifdef MANUAL_X_HOME_POS
|
||||
#define X_HOME_POS MANUAL_X_HOME_POS
|
||||
#elif ENABLED(BED_CENTER_AT_0_0)
|
||||
#define X_HOME_POS ((X_MAX_LENGTH) * (X_HOME_DIR) * 0.5)
|
||||
#else
|
||||
#define X_HOME_POS (X_HOME_DIR < 0 ? X_MIN_POS : X_MAX_POS)
|
||||
#endif
|
||||
|
||||
#ifdef MANUAL_Y_HOME_POS
|
||||
#define Y_HOME_POS MANUAL_Y_HOME_POS
|
||||
#elif ENABLED(BED_CENTER_AT_0_0)
|
||||
#define Y_HOME_POS ((Y_MAX_LENGTH) * (Y_HOME_DIR) * 0.5)
|
||||
#else
|
||||
#define Y_HOME_POS (Y_HOME_DIR < 0 ? Y_MIN_POS : Y_MAX_POS)
|
||||
#endif
|
||||
|
||||
#ifdef MANUAL_Z_HOME_POS
|
||||
#define Z_HOME_POS MANUAL_Z_HOME_POS
|
||||
#else //!MANUAL_HOME_POSITIONS – Use home switch positions based on homing direction and travel limits
|
||||
#if ENABLED(BED_CENTER_AT_0_0)
|
||||
#define X_HOME_POS (X_MAX_LENGTH) * (X_HOME_DIR) * 0.5
|
||||
#define Y_HOME_POS (Y_MAX_LENGTH) * (Y_HOME_DIR) * 0.5
|
||||
#else
|
||||
#define X_HOME_POS (X_HOME_DIR < 0 ? X_MIN_POS : X_MAX_POS)
|
||||
#define Y_HOME_POS (Y_HOME_DIR < 0 ? Y_MIN_POS : Y_MAX_POS)
|
||||
#endif
|
||||
#else
|
||||
#define Z_HOME_POS (Z_HOME_DIR < 0 ? Z_MIN_POS : Z_MAX_POS)
|
||||
#endif //!MANUAL_HOME_POSITIONS
|
||||
#endif
|
||||
|
||||
/**
|
||||
* The BLTouch Probe emulates a servo probe
|
||||
|
@ -716,18 +716,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -728,4 +728,6 @@
|
||||
#error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead."
|
||||
#elif defined(HOMING_FEEDRATE)
|
||||
#error "HOMING_FEEDRATE is deprecated. Set individual rates with HOMING_FEEDRATE_(XY|Z|E) instead."
|
||||
#elif defined(MANUAL_HOME_POSITIONS)
|
||||
#error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead."
|
||||
#endif
|
||||
|
@ -717,18 +717,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -699,18 +699,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -697,18 +697,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -709,18 +709,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -710,18 +710,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -734,18 +734,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -717,18 +717,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -717,18 +717,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -717,18 +717,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -714,18 +714,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -725,18 +725,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
// For SCARA: Offset between HomingPosition and Bed X=0 / Y=0
|
||||
#define MANUAL_X_HOME_POS -22.
|
||||
#define MANUAL_Y_HOME_POS -52.
|
||||
#define MANUAL_Z_HOME_POS 0.1 // Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
#define MANUAL_X_HOME_POS -22
|
||||
#define MANUAL_Y_HOME_POS -52
|
||||
#define MANUAL_Z_HOME_POS 0.1 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -738,18 +738,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -708,18 +708,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -717,18 +717,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -810,17 +810,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 405 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 405 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -804,17 +804,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 250 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 250 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -807,17 +807,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 250 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 250 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -801,17 +801,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 277 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 277 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -802,17 +802,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 381.4 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 381.4 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -720,18 +720,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
@ -706,18 +706,14 @@
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
// The center of the bed is at (X=0, Y=0)
|
||||
//#define BED_CENTER_AT_0_0
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
|
Loading…
Reference in New Issue
Block a user