Configurable number of M106 fans (#18883)
This commit is contained in:
parent
24139c6ff0
commit
f7dade8c2c
@ -2275,6 +2275,10 @@
|
||||
|
||||
// @section extras
|
||||
|
||||
// Set number of user-controlled fans. Disable to use all board-defined fans.
|
||||
// :[1,2,3,4,5,6,7,8]
|
||||
//#define NUM_M106_FANS 1
|
||||
|
||||
// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
//#define FAST_PWM_FAN
|
||||
|
||||
|
@ -1876,12 +1876,28 @@
|
||||
#undef AUTO_POWER_CHAMBER_FAN
|
||||
#endif
|
||||
|
||||
// Other fans
|
||||
// Print Cooling fans (limit)
|
||||
#ifdef NUM_M106_FANS
|
||||
#define MAX_FANS NUM_M106_FANS
|
||||
#else
|
||||
#define MAX_FANS 8 // Max supported fans
|
||||
#endif
|
||||
|
||||
#define _NOT_E_AUTO(N,F) (E##N##_AUTO_FAN_PIN != FAN##F##_PIN)
|
||||
#define _HAS_FAN(F) (PIN_EXISTS(FAN##F) \
|
||||
&& CONTROLLER_FAN_PIN != FAN##F##_PIN \
|
||||
&& _NOT_E_AUTO(0,F) \
|
||||
&& _NOT_E_AUTO(1,F) \
|
||||
&& _NOT_E_AUTO(2,F) \
|
||||
&& _NOT_E_AUTO(3,F) \
|
||||
&& _NOT_E_AUTO(4,F) \
|
||||
&& _NOT_E_AUTO(5,F) \
|
||||
&& _NOT_E_AUTO(6,F) \
|
||||
&& _NOT_E_AUTO(7,F) \
|
||||
&& F < MAX_FANS)
|
||||
#if PIN_EXISTS(FAN)
|
||||
#define HAS_FAN0 1
|
||||
#endif
|
||||
#define _NOT_E_AUTO(N,F) (E##N##_AUTO_FAN_PIN != FAN##F##_PIN)
|
||||
#define _HAS_FAN(F) (PIN_EXISTS(FAN##F) && CONTROLLER_FAN_PIN != FAN##F##_PIN && _NOT_E_AUTO(0,F) && _NOT_E_AUTO(1,F) && _NOT_E_AUTO(2,F) && _NOT_E_AUTO(3,F) && _NOT_E_AUTO(4,F) && _NOT_E_AUTO(5,F) && _NOT_E_AUTO(6,F) && _NOT_E_AUTO(7,F))
|
||||
#if _HAS_FAN(1)
|
||||
#define HAS_FAN1 1
|
||||
#endif
|
||||
|
@ -1106,6 +1106,13 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
||||
#error "FANMUX0_PIN and FANMUX1_PIN must be set before FANMUX2_PIN can be set."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Limited user-controlled fans
|
||||
*/
|
||||
#if NUM_M106_FANS > FAN_COUNT
|
||||
#error "The selected board doesn't support enough user-controlled fans. Reduce NUM_M106_FANS."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Limited number of servos
|
||||
*/
|
||||
|
@ -195,7 +195,7 @@ const char str_t_thermal_runaway[] PROGMEM = STR_T_THERMAL_RUNAWAY,
|
||||
#endif
|
||||
|
||||
#if ENABLED(ADAPTIVE_FAN_SLOWING)
|
||||
uint8_t Temperature::fan_speed_scaler[FAN_COUNT] = ARRAY_N(FAN_COUNT, 128, 128, 128, 128, 128, 128);
|
||||
uint8_t Temperature::fan_speed_scaler[FAN_COUNT] = ARRAY_N(FAN_COUNT, 128, 128, 128, 128, 128, 128, 128, 128);
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -92,7 +92,7 @@
|
||||
//
|
||||
// Fans
|
||||
//
|
||||
//#define FAN0_PIN 8
|
||||
//#define FAN_PIN 8
|
||||
|
||||
//
|
||||
// Auto fans
|
||||
|
Loading…
Reference in New Issue
Block a user