Merge pull request #2134 from AnHardt/preheat-all

Shift call of start_watching_heater() into setTargetHotend()
This commit is contained in:
Scott Lahteine 2015-05-21 18:36:28 -07:00
commit f919a2fed1
4 changed files with 15 additions and 27 deletions

View File

@ -3367,10 +3367,6 @@ inline void gcode_M104() {
if (dual_x_carriage_mode == DXC_DUPLICATION_MODE && target_extruder == 0)
setTargetHotend1(temp == 0.0 ? 0.0 : temp + duplicate_extruder_temp_offset);
#endif
#ifdef THERMAL_PROTECTION_HOTENDS
start_watching_heater(target_extruder);
#endif
}
}
@ -3482,10 +3478,6 @@ inline void gcode_M109() {
if (code_seen('B')) autotemp_max = code_value();
#endif
#ifdef THERMAL_PROTECTION_HOTENDS
start_watching_heater(target_extruder);
#endif
millis_t temp_ms = millis();
/* See if we are heating up or cooling down */

View File

@ -278,11 +278,7 @@ void checkHitEndstops() {
card.sdprinting = false;
card.closefile();
quickStop();
setTargetHotend0(0);
setTargetHotend1(0);
setTargetHotend2(0);
setTargetHotend3(0);
setTargetBed(0);
disable_all_heaters(); // switch off all heaters.
}
#endif
}

View File

@ -96,7 +96,16 @@ FORCE_INLINE float degBed() { return current_temperature_bed; }
FORCE_INLINE float degTargetHotend(uint8_t extruder) { return target_temperature[extruder]; }
FORCE_INLINE float degTargetBed() { return target_temperature_bed; }
FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) { target_temperature[extruder] = celsius; }
#ifdef THERMAL_PROTECTION_HOTENDS
void start_watching_heater(int e=0);
#endif
FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) {
target_temperature[extruder] = celsius;
#ifdef THERMAL_PROTECTION_HOTENDS
start_watching_heater(extruder);
#endif
}
FORCE_INLINE void setTargetBed(const float &celsius) { target_temperature_bed = celsius; }
FORCE_INLINE bool isHeatingHotend(uint8_t extruder) { return target_temperature[extruder] > current_temperature[extruder]; }
@ -137,10 +146,6 @@ void PID_autotune(float temp, int extruder, int ncycles);
void setExtruderAutoFanState(int pin, bool state);
void checkExtruderAutoFans();
#ifdef THERMAL_PROTECTION_HOTENDS
void start_watching_heater(int e=0);
#endif
FORCE_INLINE void autotempShutdown() {
#ifdef AUTOTEMP
if (autotemp_enabled) {

View File

@ -515,12 +515,11 @@ static void lcd_tune_menu() {
void _lcd_preheat(int endnum, const float temph, const float tempb, const int fan) {
if (temph > 0) setTargetHotend(temph, endnum);
setTargetBed(tempb);
#if TEMP_SENSOR_BED != 0
setTargetBed(tempb);
#endif
fanSpeed = fan;
lcd_return_to_status();
#ifdef WATCH_TEMP_PERIOD
if (endnum >= 0) start_watching_heater(endnum);
#endif
}
void lcd_preheat_pla0() { _lcd_preheat(0, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); }
void lcd_preheat_abs0() { _lcd_preheat(0, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); }
@ -602,11 +601,7 @@ void lcd_preheat_abs0() { _lcd_preheat(0, absPreheatHotendTemp, absPreheatHPBTem
#endif // more than one temperature sensor present
void lcd_cooldown() {
setTargetHotend0(0);
setTargetHotend1(0);
setTargetHotend2(0);
setTargetHotend3(0);
setTargetBed(0);
disable_all_heaters();
fanSpeed = 0;
lcd_return_to_status();
}