diff --git a/Marlin/src/feature/backlash.cpp b/Marlin/src/feature/backlash.cpp index f1a14df49d..43e6d36bec 100644 --- a/Marlin/src/feature/backlash.cpp +++ b/Marlin/src/feature/backlash.cpp @@ -123,7 +123,7 @@ void Backlash::add_correction_steps(const int32_t &da, const int32_t &db, const } #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) - #if USES_Z_MIN_PROBE_ENDSTOP + #if HAS_CUSTOM_PROBE_PIN #define TEST_PROBE_PIN (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING) #else #define TEST_PROBE_PIN (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING) diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index a86f1c1b41..ec74131592 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -501,8 +501,8 @@ #define PROBE_SELECTED (HAS_BED_PROBE || EITHER(PROBE_MANUALLY, MESH_BED_LEVELING)) #if HAS_BED_PROBE - #define USES_Z_MIN_PROBE_ENDSTOP DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) - #define HOMING_Z_WITH_PROBE (Z_HOME_DIR < 0 && !USES_Z_MIN_PROBE_ENDSTOP) + #define HAS_CUSTOM_PROBE_PIN DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) + #define HOMING_Z_WITH_PROBE (Z_HOME_DIR < 0 && !HAS_CUSTOM_PROBE_PIN) #ifndef Z_PROBE_LOW_POINT #define Z_PROBE_LOW_POINT -5 #endif diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h index 5214ac607c..5f4744e4a8 100644 --- a/Marlin/src/inc/Conditionals_post.h +++ b/Marlin/src/inc/Conditionals_post.h @@ -825,12 +825,12 @@ // Is an endstop plug used for the Z2 endstop or the bed probe? #define IS_Z2_OR_PROBE(A,M) ( \ (Z_MULTI_ENDSTOPS && Z2_USE_ENDSTOP == _##A##M##_) \ - || (USES_Z_MIN_PROBE_ENDSTOP && Z_MIN_PROBE_PIN == A##_##M##_PIN ) ) + || (HAS_CUSTOM_PROBE_PIN && Z_MIN_PROBE_PIN == A##_##M##_PIN ) ) // Is an endstop plug used for the Z3 endstop or the bed probe? #define IS_Z3_OR_PROBE(A,M) ( \ (ENABLED(Z_TRIPLE_ENDSTOPS) && Z3_USE_ENDSTOP == _##A##M##_) \ - || (USES_Z_MIN_PROBE_ENDSTOP && Z_MIN_PROBE_PIN == A##_##M##_PIN ) ) + || (HAS_CUSTOM_PROBE_PIN && Z_MIN_PROBE_PIN == A##_##M##_PIN ) ) /** * Set ENDSTOPPULLUPS for active endstop switches @@ -1005,7 +1005,7 @@ #define HAS_Z2_MAX (PIN_EXISTS(Z2_MAX)) #define HAS_Z3_MIN (PIN_EXISTS(Z3_MIN)) #define HAS_Z3_MAX (PIN_EXISTS(Z3_MAX)) -#define HAS_Z_MIN_PROBE_PIN (USES_Z_MIN_PROBE_ENDSTOP && PIN_EXISTS(Z_MIN_PROBE)) +#define HAS_Z_MIN_PROBE_PIN (HAS_CUSTOM_PROBE_PIN && PIN_EXISTS(Z_MIN_PROBE)) #define HAS_CALIBRATION_PIN (PIN_EXISTS(CALIBRATION)) // ADC Temp Sensors (Thermistor or Thermocouple with amplifier ADC interface) diff --git a/Marlin/src/module/endstops.cpp b/Marlin/src/module/endstops.cpp index e5d07cbc65..24c357e2b7 100644 --- a/Marlin/src/module/endstops.cpp +++ b/Marlin/src/module/endstops.cpp @@ -243,7 +243,7 @@ void Endstops::init() { #endif #endif - #if USES_Z_MIN_PROBE_ENDSTOP + #if HAS_CUSTOM_PROBE_PIN #if ENABLED(ENDSTOPPULLUP_ZMIN_PROBE) SET_INPUT_PULLUP(Z_MIN_PROBE_PIN); #elif ENABLED(ENDSTOPPULLDOWN_ZMIN_PROBE) @@ -366,7 +366,7 @@ void Endstops::event_handler() { ENDSTOP_HIT_TEST_Y(); ENDSTOP_HIT_TEST_Z(); - #if USES_Z_MIN_PROBE_ENDSTOP + #if HAS_CUSTOM_PROBE_PIN #define P_AXIS Z_AXIS if (TEST(hit_state, Z_MIN_PROBE)) _ENDSTOP_HIT_ECHO(P, 'P'); #endif @@ -443,7 +443,7 @@ void _O2 Endstops::M119() { #if HAS_Z3_MAX ES_REPORT(Z3_MAX); #endif - #if USES_Z_MIN_PROBE_ENDSTOP + #if HAS_CUSTOM_PROBE_PIN print_es_state(READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING, PSTR(MSG_Z_PROBE)); #endif #if HAS_FILAMENT_SENSOR @@ -538,60 +538,52 @@ void Endstops::update() { * Check and update endstops */ #if HAS_X_MIN && !X_SPI_SENSORLESS + UPDATE_ENDSTOP_BIT(X, MIN); #if ENABLED(X_DUAL_ENDSTOPS) - UPDATE_ENDSTOP_BIT(X, MIN); #if HAS_X2_MIN UPDATE_ENDSTOP_BIT(X2, MIN); #else COPY_LIVE_STATE(X_MIN, X2_MIN); #endif - #else - UPDATE_ENDSTOP_BIT(X, MIN); #endif #endif #if HAS_X_MAX && !X_SPI_SENSORLESS + UPDATE_ENDSTOP_BIT(X, MAX); #if ENABLED(X_DUAL_ENDSTOPS) - UPDATE_ENDSTOP_BIT(X, MAX); #if HAS_X2_MAX UPDATE_ENDSTOP_BIT(X2, MAX); #else COPY_LIVE_STATE(X_MAX, X2_MAX); #endif - #else - UPDATE_ENDSTOP_BIT(X, MAX); #endif #endif #if HAS_Y_MIN && !Y_SPI_SENSORLESS + UPDATE_ENDSTOP_BIT(Y, MIN); #if ENABLED(Y_DUAL_ENDSTOPS) - UPDATE_ENDSTOP_BIT(Y, MIN); #if HAS_Y2_MIN UPDATE_ENDSTOP_BIT(Y2, MIN); #else COPY_LIVE_STATE(Y_MIN, Y2_MIN); #endif - #else - UPDATE_ENDSTOP_BIT(Y, MIN); #endif #endif #if HAS_Y_MAX && !Y_SPI_SENSORLESS + UPDATE_ENDSTOP_BIT(Y, MAX); #if ENABLED(Y_DUAL_ENDSTOPS) - UPDATE_ENDSTOP_BIT(Y, MAX); #if HAS_Y2_MAX UPDATE_ENDSTOP_BIT(Y2, MAX); #else COPY_LIVE_STATE(Y_MAX, Y2_MAX); #endif - #else - UPDATE_ENDSTOP_BIT(Y, MAX); #endif #endif #if HAS_Z_MIN && !Z_SPI_SENSORLESS + UPDATE_ENDSTOP_BIT(Z, MIN); #if Z_MULTI_ENDSTOPS - UPDATE_ENDSTOP_BIT(Z, MIN); #if HAS_Z2_MIN UPDATE_ENDSTOP_BIT(Z2, MIN); #else @@ -604,15 +596,11 @@ void Endstops::update() { COPY_LIVE_STATE(Z_MIN, Z3_MIN); #endif #endif - #elif ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) - UPDATE_ENDSTOP_BIT(Z, MIN); - #elif Z_HOME_DIR < 0 - UPDATE_ENDSTOP_BIT(Z, MIN); #endif #endif // When closing the gap check the enabled probe - #if USES_Z_MIN_PROBE_ENDSTOP + #if HAS_CUSTOM_PROBE_PIN UPDATE_ENDSTOP_BIT(Z, MIN_PROBE); #endif @@ -632,7 +620,7 @@ void Endstops::update() { COPY_LIVE_STATE(Z_MAX, Z3_MAX); #endif #endif - #elif !USES_Z_MIN_PROBE_ENDSTOP || Z_MAX_PIN != Z_MIN_PROBE_PIN + #elif !HAS_CUSTOM_PROBE_PIN || Z_MAX_PIN != Z_MIN_PROBE_PIN // If this pin isn't the bed probe it's the Z endstop UPDATE_ENDSTOP_BIT(Z, MAX); #endif @@ -765,7 +753,7 @@ void Endstops::update() { #else #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) if (z_probe_enabled) PROCESS_ENDSTOP(Z, MIN); - #elif USES_Z_MIN_PROBE_ENDSTOP + #elif HAS_CUSTOM_PROBE_PIN if (!z_probe_enabled) PROCESS_ENDSTOP(Z, MIN); #else PROCESS_ENDSTOP(Z, MIN); @@ -774,7 +762,7 @@ void Endstops::update() { #endif // When closing the gap check the enabled probe - #if USES_Z_MIN_PROBE_ENDSTOP + #if HAS_CUSTOM_PROBE_PIN if (z_probe_enabled) PROCESS_ENDSTOP(Z, MIN_PROBE); #endif } @@ -784,7 +772,7 @@ void Endstops::update() { PROCESS_TRIPLE_ENDSTOP(Z, Z2, Z3, MAX); #elif ENABLED(Z_DUAL_ENDSTOPS) PROCESS_DUAL_ENDSTOP(Z, Z2, MAX); - #elif !USES_Z_MIN_PROBE_ENDSTOP || Z_MAX_PIN != Z_MIN_PROBE_PIN + #elif !HAS_CUSTOM_PROBE_PIN || Z_MAX_PIN != Z_MIN_PROBE_PIN // If this pin is not hijacked for the bed probe // then it belongs to the Z endstop PROCESS_ENDSTOP(Z, MAX); diff --git a/Marlin/src/module/probe.cpp b/Marlin/src/module/probe.cpp index f183170a20..cbe6035af7 100644 --- a/Marlin/src/module/probe.cpp +++ b/Marlin/src/module/probe.cpp @@ -387,7 +387,7 @@ bool set_probe_deployed(const bool deploy) { const xy_pos_t old_xy = current_position; #if ENABLED(PROBE_TRIGGERED_WHEN_STOWED_TEST) - #if USES_Z_MIN_PROBE_ENDSTOP + #if HAS_CUSTOM_PROBE_PIN #define PROBE_STOWED() (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING) #else #define PROBE_STOWED() (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING) diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index 1d9c448458..39afc2b388 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -904,7 +904,7 @@ // // Disable unused endstop / probe pins // -#if !USES_Z_MIN_PROBE_ENDSTOP +#if !HAS_CUSTOM_PROBE_PIN #undef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN -1 #endif diff --git a/Marlin/src/pins/sam/pins_RURAMPS4D_11.h b/Marlin/src/pins/sam/pins_RURAMPS4D_11.h index b457c7852c..45540e8dad 100644 --- a/Marlin/src/pins/sam/pins_RURAMPS4D_11.h +++ b/Marlin/src/pins/sam/pins_RURAMPS4D_11.h @@ -118,7 +118,7 @@ //#define E3_MS2_PIN ? //#define E3_MS3_PIN ? -#if USES_Z_MIN_PROBE_ENDSTOP +#if HAS_CUSTOM_PROBE_PIN #define Z_MIN_PROBE_PIN 49 #endif diff --git a/Marlin/src/pins/sam/pins_RURAMPS4D_13.h b/Marlin/src/pins/sam/pins_RURAMPS4D_13.h index 6931654a7a..c8ff71673b 100644 --- a/Marlin/src/pins/sam/pins_RURAMPS4D_13.h +++ b/Marlin/src/pins/sam/pins_RURAMPS4D_13.h @@ -106,7 +106,7 @@ #define E2_CS_PIN 61 #endif -#if USES_Z_MIN_PROBE_ENDSTOP +#if HAS_CUSTOM_PROBE_PIN #define Z_MIN_PROBE_PIN 49 #endif