/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once #ifndef STM32F4 #error "Oops! Select an STM32F4 board in 'Tools > Board.'" #elif HOTENDS > 3 || E_STEPPERS > 3 #error "RUMBA32 supports up to 3 hotends / E-steppers." #endif #ifndef BOARD_INFO_NAME #define BOARD_INFO_NAME "FYSETC_S6" #endif #ifndef DEFAULT_MACHINE_NAME #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME #endif // Change the priority to 3. Priority 2 is for software serial. //#define TEMP_TIMER_IRQ_PRIO 3 // // EEPROM Emulation // #if NO_EEPROM_SELECTED #define FLASH_EEPROM_EMULATION //#define SRAM_EEPROM_EMULATION //#define I2C_EEPROM #endif #if ENABLED(FLASH_EEPROM_EMULATION) // Decrease delays and flash wear by spreading writes across the // 128 kB sector allocated for EEPROM emulation. #define FLASH_EEPROM_LEVELING #elif ENABLED(I2C_EEPROM) #undef E2END // Defined in Arduino Core STM32 to be used with EEPROM emulation. This board uses a real EEPROM. #define E2END 0xFFF // 4KB #endif // // Servos // #define SERVO0_PIN PA3 // // Limit Switches // #define X_MIN_PIN PB14 #define X_MAX_PIN PA1 #define Y_MIN_PIN PB13 #define Y_MAX_PIN PA2 #define Z_MIN_PIN PA0 #define Z_MAX_PIN PA3 // // Filament Sensor // share with X_MAX_PIN // #ifndef FIL_RUNOUT_PIN #define FIL_RUNOUT_PIN PA1 #endif // // Steppers // #define X_STEP_PIN PE11 #define X_DIR_PIN PE10 #define X_ENABLE_PIN PE12 #define X_CS_PIN PE7 #define Y_STEP_PIN PD8 #define Y_DIR_PIN PB12 #define Y_ENABLE_PIN PD9 #define Y_CS_PIN PE15 #define Z_STEP_PIN PD14 #define Z_DIR_PIN PD13 #define Z_ENABLE_PIN PD15 #define Z_CS_PIN PD10 #define E0_STEP_PIN PD5 #define E0_DIR_PIN PD6 #define E0_ENABLE_PIN PD4 #define E0_CS_PIN PD7 #define E1_STEP_PIN PE6 #define E1_DIR_PIN PC13 #define E1_ENABLE_PIN PE5 #define E1_CS_PIN PC14 #define E2_STEP_PIN PE2 #define E2_DIR_PIN PE4 #define E2_ENABLE_PIN PE3 #define E2_CS_PIN PC15 #if HAS_TMC_UART // // TMC2208/TMC2209 stepper drivers // // // Software serial // #define X_SERIAL_TX_PIN PE9 #define X_SERIAL_RX_PIN PE8 #define Y_SERIAL_TX_PIN PE14 #define Y_SERIAL_RX_PIN PE13 #define Z_SERIAL_TX_PIN PD11 #define Z_SERIAL_RX_PIN PD12 #define E0_SERIAL_TX_PIN PD3 #define E0_SERIAL_RX_PIN PA15 #define E1_SERIAL_TX_PIN PC4 #define E1_SERIAL_RX_PIN PC5 #define E2_SERIAL_TX_PIN PE1 #define E2_SERIAL_RX_PIN PE0 #endif // // Temperature Sensors // #define TEMP_0_PIN PC0 #define TEMP_1_PIN PC1 #define TEMP_2_PIN PC2 #define TEMP_BED_PIN PC3 // // Heaters / Fans // #define HEATER_0_PIN PB3 #define HEATER_1_PIN PB4 #define HEATER_2_PIN PB15 #define HEATER_BED_PIN PC8 #define FAN_PIN PB0 #define FAN1_PIN PB1 #define FAN2_PIN PB2 // // SPI // #define SCK_PIN PA5 #define MISO_PIN PA6 #define MOSI_PIN PA7 // // Misc. Functions // //#define LED_PIN PB14 //#define BTN_PIN PC10 //#define PS_ON_PIN PE11 //#define KILL_PIN PC5 #define SDSS PA4 #define SD_DETECT_PIN PB10 // // LCD / Controller // #if HAS_SPI_LCD #define BEEPER_PIN PC9 #define BTN_ENC PA8 #if ENABLED(CR10_STOCKDISPLAY) #define LCD_PINS_RS PD0 #define BTN_EN1 PC11 #define BTN_EN2 PC10 #define LCD_PINS_ENABLE PD1 #define LCD_PINS_D4 PC12 // CR10_Stock Display needs a different delay setting on SKR PRO v1.1, so undef it here. // It will be defined again at the #HAS_GRAPHICAL_LCD section below. #undef ST7920_DELAY_1 #undef ST7920_DELAY_2 #undef ST7920_DELAY_3 #else #define LCD_PINS_RS PD2 #define BTN_EN1 PC6 #define BTN_EN2 PC7 #define LCD_SDSS PA4 #define LCD_PINS_ENABLE PC11 #define LCD_PINS_D4 PC10 #if ENABLED(FYSETC_MINI_12864) // See https://wiki.fysetc.com/Mini12864_Panel #define DOGLCD_CS PC11 #define DOGLCD_A0 PD2 #if ENABLED(FYSETC_GENERIC_12864_1_1) #define LCD_BACKLIGHT_PIN PD0 #endif #define LCD_RESET_PIN PC10 // Must be high or open for LCD to operate normally. #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #ifndef RGB_LED_R_PIN #define RGB_LED_R_PIN PC12 #endif #ifndef RGB_LED_G_PIN #define RGB_LED_G_PIN PD0 #endif #ifndef RGB_LED_B_PIN #define RGB_LED_B_PIN PD1 #endif #elif ENABLED(FYSETC_MINI_12864_2_1) #define NEOPIXEL_PIN PC12 #endif #endif // !FYSETC_MINI_12864 #if ENABLED(ULTIPANEL) #define LCD_PINS_D5 PC12 #define LCD_PINS_D6 PD0 #define LCD_PINS_D7 PD1 #endif #endif // Alter timing for graphical display #if HAS_GRAPHICAL_LCD #ifndef ST7920_DELAY_1 #define ST7920_DELAY_1 DELAY_NS(96) #endif #ifndef ST7920_DELAY_2 #define ST7920_DELAY_2 DELAY_NS(48) #endif #ifndef ST7920_DELAY_3 #define ST7920_DELAY_3 DELAY_NS(600) #endif #endif #endif // HAS_SPI_LCD #ifndef RGB_LED_R_PIN #define RGB_LED_R_PIN PB6 #endif #ifndef RGB_LED_G_PIN #define RGB_LED_G_PIN PB5 #endif #ifndef RGB_LED_B_PIN #define RGB_LED_B_PIN PB7 #endif #ifndef RGB_LED_W_PIN #define RGB_LED_W_PIN -1 #endif