495 lines
16 KiB
C
495 lines
16 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
#include "env_validate.h"
|
|
|
|
#if E_STEPPERS > MAX_E_STEPPERS
|
|
#error "Marlin extruder/hotends limit! Increase MAX_E_STEPPERS to continue."
|
|
#elif HOTENDS > 8 || E_STEPPERS > 8
|
|
#error "BIGTREE GTR V1.0 supports up to 8 hotends / E-steppers."
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "BTT GTR V1.0"
|
|
|
|
#define USES_DIAG_JUMPERS
|
|
#define HAS_OTG_USB_HOST_SUPPORT // USB Flash Drive support
|
|
#define M5_EXTENDER // The M5 extender is attached
|
|
|
|
// Onboard I2C EEPROM
|
|
#define I2C_EEPROM
|
|
#define MARLIN_EEPROM_SIZE 0x2000 // 8KB (24C64 ... 64Kb = 8KB)
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
#define SERVO0_PIN PB11 // BLTOUCH
|
|
#define SOL0_PIN PC7 // Toolchanger
|
|
|
|
#if ENABLED(TOOL_SENSOR)
|
|
#define TOOL_SENSOR1_PIN PH6
|
|
#define TOOL_SENSOR2_PIN PI4
|
|
//#define TOOL_SENSOR3_PIN PF4
|
|
#else
|
|
#define PS_ON_PIN PH6
|
|
#endif
|
|
|
|
//
|
|
// Trinamic Stallguard pins
|
|
//
|
|
#define X_DIAG_PIN PF2 // X-
|
|
#define Y_DIAG_PIN PC13 // Y-
|
|
#define Z_DIAG_PIN PE0 // Z-
|
|
#define E0_DIAG_PIN PG14 // X+
|
|
#define E1_DIAG_PIN PG9 // Y+
|
|
#define E2_DIAG_PIN PD3 // Z+
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#ifdef X_STALL_SENSITIVITY
|
|
#define X_STOP_PIN X_DIAG_PIN
|
|
#if X_HOME_TO_MIN
|
|
#define X_MAX_PIN E0_DIAG_PIN // X+
|
|
#else
|
|
#define X_MIN_PIN E0_DIAG_PIN // X+
|
|
#endif
|
|
#else
|
|
#define X_MIN_PIN X_DIAG_PIN // X-
|
|
#define X_MAX_PIN E0_DIAG_PIN // X+
|
|
#endif
|
|
|
|
#ifdef Y_STALL_SENSITIVITY
|
|
#define Y_STOP_PIN Y_DIAG_PIN
|
|
#if Y_HOME_TO_MIN
|
|
#define Y_MAX_PIN E1_DIAG_PIN // Y+
|
|
#else
|
|
#define Y_MIN_PIN E1_DIAG_PIN // Y+
|
|
#endif
|
|
#else
|
|
#define Y_MIN_PIN Y_DIAG_PIN // Y-
|
|
#define Y_MAX_PIN E1_DIAG_PIN // Y+
|
|
#endif
|
|
|
|
#ifdef Z_STALL_SENSITIVITY
|
|
#define Z_STOP_PIN Z_DIAG_PIN
|
|
#if Z_HOME_TO_MIN
|
|
#define Z_MAX_PIN E2_DIAG_PIN // Z+
|
|
#else
|
|
#define Z_MIN_PIN E2_DIAG_PIN // Z+
|
|
#endif
|
|
#else
|
|
#define Z_MIN_PIN Z_DIAG_PIN // Z-
|
|
#define Z_MAX_PIN E2_DIAG_PIN // Z+
|
|
#endif
|
|
|
|
//
|
|
// Pins on the extender
|
|
//
|
|
#if ENABLED(M5_EXTENDER)
|
|
#define X2_STOP_PIN PI4 // M5 M1_STOP
|
|
#define Y2_STOP_PIN PF12 // M5 M5_STOP
|
|
#define Z2_STOP_PIN PF4 // M5 M2_STOP
|
|
#define Z3_STOP_PIN PI7 // M5 M4_STOP
|
|
#define Z4_STOP_PIN PF6 // M5 M3_STOP
|
|
#endif
|
|
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
#define Z_MIN_PROBE_PIN PH11 // Z Probe must be PH11
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN PC15
|
|
#define X_DIR_PIN PF0
|
|
#define X_ENABLE_PIN PF1
|
|
#ifndef X_CS_PIN
|
|
#define X_CS_PIN PC14
|
|
#endif
|
|
|
|
#define Y_STEP_PIN PE3
|
|
#define Y_DIR_PIN PE2
|
|
#define Y_ENABLE_PIN PE4
|
|
#ifndef Y_CS_PIN
|
|
#define Y_CS_PIN PE1
|
|
#endif
|
|
|
|
#define Z_STEP_PIN PB8
|
|
#define Z_DIR_PIN PB7 // PB7
|
|
#define Z_ENABLE_PIN PB9
|
|
#ifndef Z_CS_PIN
|
|
#define Z_CS_PIN PB5
|
|
#endif
|
|
|
|
#define E0_STEP_PIN PG12
|
|
#define E0_DIR_PIN PG11
|
|
#define E0_ENABLE_PIN PG13
|
|
#ifndef E0_CS_PIN
|
|
#define E0_CS_PIN PG10
|
|
#endif
|
|
|
|
#define E1_STEP_PIN PD6
|
|
#define E1_DIR_PIN PD5
|
|
#define E1_ENABLE_PIN PD7
|
|
#ifndef E1_CS_PIN
|
|
#define E1_CS_PIN PD4
|
|
#endif
|
|
|
|
#define E2_STEP_PIN PD1
|
|
#define E2_DIR_PIN PD0
|
|
#define E2_ENABLE_PIN PD2
|
|
#ifndef E2_CS_PIN
|
|
#define E2_CS_PIN PC12
|
|
#endif
|
|
|
|
#if ENABLED(M5_EXTENDER)
|
|
|
|
#define E3_STEP_PIN PF3
|
|
#define E3_DIR_PIN PG3
|
|
#define E3_ENABLE_PIN PF8
|
|
#ifndef E3_CS_PIN
|
|
#define E3_CS_PIN PG4
|
|
#endif
|
|
|
|
#define E4_STEP_PIN PD14
|
|
#define E4_DIR_PIN PD11
|
|
#define E4_ENABLE_PIN PG2
|
|
#ifndef E4_CS_PIN
|
|
#define E4_CS_PIN PE15
|
|
#endif
|
|
|
|
#define E5_STEP_PIN PE12
|
|
#define E5_DIR_PIN PE10
|
|
#define E5_ENABLE_PIN PF14
|
|
#ifndef E5_CS_PIN
|
|
#define E5_CS_PIN PE7
|
|
#endif
|
|
|
|
#define E6_STEP_PIN PG0
|
|
#define E6_DIR_PIN PG1
|
|
#define E6_ENABLE_PIN PE8
|
|
#ifndef E6_CS_PIN
|
|
#define E6_CS_PIN PF15
|
|
#endif
|
|
|
|
#define E7_STEP_PIN PH12
|
|
#define E7_DIR_PIN PH15
|
|
#define E7_ENABLE_PIN PI0
|
|
#ifndef E7_CS_PIN
|
|
#define E7_CS_PIN PH14
|
|
#endif
|
|
|
|
#endif
|
|
|
|
//
|
|
// Software SPI pins for TMC2130 stepper drivers
|
|
//
|
|
#if ENABLED(TMC_USE_SW_SPI)
|
|
#ifndef TMC_SW_MOSI
|
|
#define TMC_SW_MOSI PG15
|
|
#endif
|
|
#ifndef TMC_SW_MISO
|
|
#define TMC_SW_MISO PB6
|
|
#endif
|
|
#ifndef TMC_SW_SCK
|
|
#define TMC_SW_SCK PB3
|
|
#endif
|
|
#endif
|
|
|
|
#if HAS_TMC_UART
|
|
/**
|
|
* TMC2208/TMC2209 stepper drivers
|
|
*
|
|
* Hardware serial communication ports.
|
|
* If undefined software serial is used according to the pins below
|
|
*/
|
|
//#define X_HARDWARE_SERIAL Serial1
|
|
//#define X2_HARDWARE_SERIAL Serial1
|
|
//#define Y_HARDWARE_SERIAL Serial1
|
|
//#define Y2_HARDWARE_SERIAL Serial1
|
|
//#define Z_HARDWARE_SERIAL Serial1
|
|
//#define Z2_HARDWARE_SERIAL Serial1
|
|
//#define E0_HARDWARE_SERIAL Serial1
|
|
//#define E1_HARDWARE_SERIAL Serial1
|
|
//#define E2_HARDWARE_SERIAL Serial1
|
|
//#define E3_HARDWARE_SERIAL Serial1 // M5 MOTOR 1
|
|
//#define E4_HARDWARE_SERIAL Serial1 // M5 MOTOR 2
|
|
//#define E5_HARDWARE_SERIAL Serial1 // M5 MOTOR 3
|
|
//#define E6_HARDWARE_SERIAL Serial1 // M5 MOTOR 4
|
|
//#define E7_HARDWARE_SERIAL Serial1 // M5 MOTOR 5
|
|
|
|
#define X_SERIAL_TX_PIN PC14
|
|
#define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
|
|
|
|
#define Y_SERIAL_TX_PIN PE1
|
|
#define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
|
|
|
|
#define Z_SERIAL_TX_PIN PB5
|
|
#define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
|
|
|
|
#define E0_SERIAL_TX_PIN PG10
|
|
#define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN
|
|
|
|
#define E1_SERIAL_TX_PIN PD4
|
|
#define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN
|
|
|
|
#define E2_SERIAL_TX_PIN PC12
|
|
#define E2_SERIAL_RX_PIN E2_SERIAL_TX_PIN
|
|
|
|
#if ENABLED(M5_EXTENDER)
|
|
#define E3_SERIAL_TX_PIN PG4
|
|
#define E3_SERIAL_RX_PIN E3_SERIAL_TX_PIN
|
|
|
|
#define E4_SERIAL_TX_PIN PE15
|
|
#define E4_SERIAL_RX_PIN E4_SERIAL_TX_PIN
|
|
|
|
#define E5_SERIAL_TX_PIN PE7
|
|
#define E5_SERIAL_RX_PIN E5_SERIAL_TX_PIN
|
|
|
|
#define E6_SERIAL_TX_PIN PF15
|
|
#define E6_SERIAL_RX_PIN E6_SERIAL_TX_PIN
|
|
|
|
#define E7_SERIAL_TX_PIN PH14
|
|
#define E7_SERIAL_RX_PIN E7_SERIAL_TX_PIN
|
|
#endif
|
|
|
|
// Reduce baud rate to improve software serial reliability
|
|
#define TMC_BAUD_RATE 19200
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN PC1 // T1 <-> E0
|
|
#define TEMP_1_PIN PC2 // T2 <-> E1
|
|
#define TEMP_2_PIN PC3 // T3 <-> E2
|
|
|
|
#if ENABLED(M5_EXTENDER)
|
|
#define TEMP_3_PIN PA3 // M5 TEMP1
|
|
#define TEMP_4_PIN PF9 // M5 TEMP2
|
|
#define TEMP_5_PIN PF10 // M5 TEMP3
|
|
#define TEMP_6_PIN PF7 // M5 TEMP4
|
|
#define TEMP_7_PIN PF5 // M5 TEMP5
|
|
#endif
|
|
|
|
#define TEMP_BED_PIN PC0 // T0 <-> Bed
|
|
|
|
// SPI for MAX Thermocouple
|
|
// Uses a separate SPI bus
|
|
// If you have a two-way thermocouple, you can customize two TEMP_x_CS_PIN pins (x:0~1)
|
|
|
|
#define TEMP_0_CS_PIN PH9 // GTR K-TEMP
|
|
#define TEMP_0_SCK_PIN PI1 // SCK
|
|
#define TEMP_0_MISO_PIN PI2 // MISO
|
|
//#define TEMP_0_MOSI_PIN ... // For MAX31865
|
|
|
|
#define TEMP_1_CS_PIN PH2 // M5 K-TEMP
|
|
#define TEMP_1_SCK_PIN TEMP_0_SCK_PIN
|
|
#define TEMP_1_MISO_PIN TEMP_0_MISO_PIN
|
|
//#define TEMP_1_MOSI_PIN TEMP_0_MOSI_PIN
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PB1 // Heater0
|
|
#define HEATER_1_PIN PA1 // Heater1
|
|
#define HEATER_2_PIN PB0 // Heater2
|
|
|
|
#if ENABLED(M5_EXTENDER)
|
|
#define HEATER_3_PIN PD15 // M5 HEAT1
|
|
#define HEATER_4_PIN PD13 // M5 HEAT2
|
|
#define HEATER_5_PIN PD12 // M5 HEAT3
|
|
#define HEATER_6_PIN PE13 // M5 HEAT4
|
|
#define HEATER_7_PIN PI6 // M5 HEAT5
|
|
#endif
|
|
|
|
#define HEATER_BED_PIN PA2 // Hotbed
|
|
|
|
#define FAN_PIN PE5 // Fan0
|
|
#define FAN1_PIN PE6 // Fan1
|
|
#define FAN2_PIN PC8 // Fan2
|
|
|
|
#if ENABLED(M5_EXTENDER)
|
|
#define FAN3_PIN PI5 // M5 FAN1
|
|
#define FAN4_PIN PE9 // M5 FAN2
|
|
#define FAN5_PIN PE11 // M5 FAN3
|
|
//#define FAN6_PIN PC9 // M5 FAN4
|
|
//#define FAN7_PIN PE14 // M5 FAN5
|
|
#endif
|
|
|
|
#ifndef SDCARD_CONNECTION
|
|
#define SDCARD_CONNECTION ONBOARD
|
|
#endif
|
|
|
|
//
|
|
// By default the LCD SD (SPI2) is enabled
|
|
// Onboard SD is on a completely separate SPI bus, and requires
|
|
// overriding pins to access.
|
|
//
|
|
#if SD_CONNECTION_IS(LCD)
|
|
|
|
#define SD_DETECT_PIN EXP2_04_PIN
|
|
#define SDSS EXP2_07_PIN
|
|
|
|
#elif SD_CONNECTION_IS(ONBOARD)
|
|
|
|
#define SDSS PA4
|
|
#define SD_SS_PIN SDSS
|
|
#define SD_SCK_PIN PA5
|
|
#define SD_MISO_PIN PA6
|
|
#define SD_MOSI_PIN PA7
|
|
#define SD_DETECT_PIN PC4
|
|
|
|
#elif SD_CONNECTION_IS(CUSTOM_CABLE)
|
|
#error "CUSTOM_CABLE is not a supported SDCARD_CONNECTION for this board"
|
|
#endif
|
|
|
|
/**
|
|
* ------ ------
|
|
* NC | 1 2 | GND 5V | 1 2 | GND
|
|
* RESET | 3 4 | PB10 (SD_DETECT) (LCD_D7) PG5 | 3 4 | PG6 (LCD_D6)
|
|
* (MOSI) PB15 | 5 6 | PH10 (BTN_EN2) (LCD_D5) PG7 | 5 6 | PG8 (LCD_D4)
|
|
* (SD_SS) PB12 | 7 8 | PD10 (BTN_EN1) (LCD_RS) PA8 | 7 8 | PC10 (LCD_EN)
|
|
* (SCK) PB13 | 9 10 | PB14 (MISO) (BTN_ENC) PA15 | 9 10 | PC11 (BEEPER)
|
|
* ------ ------
|
|
* EXP2 EXP1
|
|
*/
|
|
#define EXP1_03_PIN PG5
|
|
#define EXP1_04_PIN PG6
|
|
#define EXP1_05_PIN PG7
|
|
#define EXP1_06_PIN PG8
|
|
#define EXP1_07_PIN PA8
|
|
#define EXP1_08_PIN PC10
|
|
#define EXP1_09_PIN PA15
|
|
#define EXP1_10_PIN PC11
|
|
|
|
#define EXP2_04_PIN PB10
|
|
#define EXP2_05_PIN PB15
|
|
#define EXP2_06_PIN PH10
|
|
#define EXP2_07_PIN PB12
|
|
#define EXP2_08_PIN PD10
|
|
#define EXP2_09_PIN PB13
|
|
#define EXP2_10_PIN PB14
|
|
|
|
//
|
|
// LCDs and Controllers
|
|
//
|
|
#if ANY(TFT_COLOR_UI, TFT_LVGL_UI, TFT_CLASSIC_UI)
|
|
|
|
#define TFT_CS_PIN EXP2_07_PIN
|
|
#define TFT_A0_PIN EXP2_04_PIN
|
|
#define TFT_SCK_PIN EXP2_09_PIN
|
|
#define TFT_MISO_PIN EXP2_10_PIN
|
|
#define TFT_MOSI_PIN EXP2_05_PIN
|
|
|
|
#define TOUCH_INT_PIN EXP1_04_PIN
|
|
#define TOUCH_MISO_PIN EXP1_05_PIN
|
|
#define TOUCH_MOSI_PIN EXP1_08_PIN
|
|
#define TOUCH_SCK_PIN EXP1_06_PIN
|
|
#define TOUCH_CS_PIN EXP1_07_PIN
|
|
#define BTN_ENC EXP1_09_PIN
|
|
#define BTN_EN1 EXP2_08_PIN
|
|
#define BTN_EN2 EXP2_06_PIN
|
|
|
|
#elif HAS_WIRED_LCD
|
|
#define BEEPER_PIN EXP1_10_PIN
|
|
#define BTN_ENC EXP1_09_PIN
|
|
|
|
#if ENABLED(CR10_STOCKDISPLAY)
|
|
#define LCD_PINS_RS EXP1_04_PIN
|
|
|
|
#define BTN_EN1 EXP1_08_PIN
|
|
#define BTN_EN2 EXP1_06_PIN
|
|
|
|
#define LCD_PINS_ENABLE EXP1_03_PIN
|
|
#define LCD_PINS_D4 EXP1_05_PIN
|
|
|
|
#elif ENABLED(MKS_MINI_12864)
|
|
#define DOGLCD_A0 EXP1_04_PIN
|
|
#define DOGLCD_CS EXP1_05_PIN
|
|
#define BTN_EN1 EXP2_08_PIN
|
|
#define BTN_EN2 EXP2_06_PIN
|
|
|
|
#if SD_CONNECTION_IS(ONBOARD)
|
|
#define SOFTWARE_SPI
|
|
#endif
|
|
#else
|
|
|
|
#define LCD_PINS_RS EXP1_07_PIN
|
|
|
|
#define BTN_EN1 EXP2_08_PIN
|
|
#define BTN_EN2 EXP2_06_PIN
|
|
|
|
#define LCD_PINS_ENABLE EXP1_08_PIN
|
|
#define LCD_PINS_D4 EXP1_06_PIN
|
|
|
|
#if ENABLED(FYSETC_MINI_12864)
|
|
#define DOGLCD_CS EXP1_08_PIN
|
|
#define DOGLCD_A0 EXP1_07_PIN
|
|
|
|
#if SD_CONNECTION_IS(ONBOARD)
|
|
#define SOFTWARE_SPI
|
|
#endif
|
|
|
|
//#define LCD_BACKLIGHT_PIN -1
|
|
#define LCD_RESET_PIN EXP1_06_PIN // Must be high or open for LCD to operate normally.
|
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN EXP1_05_PIN
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN EXP1_04_PIN
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN EXP1_03_PIN
|
|
#endif
|
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
|
#define NEOPIXEL_PIN EXP1_05_PIN
|
|
#endif
|
|
#endif // !FYSETC_MINI_12864
|
|
|
|
#if IS_ULTIPANEL
|
|
#define LCD_PINS_D5 EXP1_05_PIN
|
|
#define LCD_PINS_D6 EXP1_04_PIN
|
|
#define LCD_PINS_D7 EXP1_03_PIN
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
|
#define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
// Alter timing for graphical display
|
|
#if IS_U8GLIB_ST7920
|
|
#define BOARD_ST7920_DELAY_1 125
|
|
#define BOARD_ST7920_DELAY_2 90
|
|
#define BOARD_ST7920_DELAY_3 600
|
|
#endif
|
|
|
|
#endif // HAS_WIRED_LCD
|
|
|
|
#undef TP
|
|
#undef M5_EXTENDER
|