274 lines
8.2 KiB
C
274 lines
8.2 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
#if NOT_TARGET(STM32F4)
|
|
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
|
|
#elif HOTENDS > 1 || E_STEPPERS > 1
|
|
#error "BIGTREE BTT002 V1.0 only supports one hotend / E-stepper. Comment out this line to continue."
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "BTT BTT002 V1.0"
|
|
|
|
// Use one of these or SDCard-based Emulation will be used
|
|
#if NO_EEPROM_SELECTED
|
|
//#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation
|
|
#define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation
|
|
#endif
|
|
|
|
#if ENABLED(FLASH_EEPROM_EMULATION)
|
|
// Decrease delays and flash wear by spreading writes across the
|
|
// 128 kB sector allocated for EEPROM emulation.
|
|
#define FLASH_EEPROM_LEVELING
|
|
#endif
|
|
|
|
// Ignore temp readings during development.
|
|
//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_STOP_PIN PD3
|
|
#define Y_STOP_PIN PD2
|
|
#define Z_STOP_PIN PD1 // Shares J4 connector with PC3
|
|
|
|
//
|
|
// Z Probe must be this pin
|
|
//
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
#define Z_MIN_PROBE_PIN PD1
|
|
#endif
|
|
|
|
//
|
|
// Filament Runout Sensor
|
|
//
|
|
#ifndef FIL_RUNOUT_PIN
|
|
#define FIL_RUNOUT_PIN PA15
|
|
#endif
|
|
|
|
//
|
|
// Power Loss Detection
|
|
//
|
|
#ifndef POWER_LOSS_PIN
|
|
#define POWER_LOSS_PIN PD4
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN PA9
|
|
#define X_DIR_PIN PA10
|
|
#define X_ENABLE_PIN PA8
|
|
#ifndef X_CS_PIN
|
|
#define X_CS_PIN PE2
|
|
#endif
|
|
|
|
#define Y_STEP_PIN PC8
|
|
#define Y_DIR_PIN PC9
|
|
#define Y_ENABLE_PIN PC7
|
|
#ifndef Y_CS_PIN
|
|
#define Y_CS_PIN PE3
|
|
#endif
|
|
|
|
#define Z_STEP_PIN PD15
|
|
#define Z_DIR_PIN PC6
|
|
#define Z_ENABLE_PIN PD14
|
|
#ifndef Z_CS_PIN
|
|
#define Z_CS_PIN PE4
|
|
#endif
|
|
|
|
#define E0_STEP_PIN PD12
|
|
#define E0_DIR_PIN PD13
|
|
#define E0_ENABLE_PIN PD11
|
|
#ifndef E0_CS_PIN
|
|
#define E0_CS_PIN PD7
|
|
#endif
|
|
|
|
//
|
|
// Software SPI pins for TMC2130 stepper drivers
|
|
//
|
|
#if ENABLED(TMC_USE_SW_SPI)
|
|
#ifndef TMC_SW_MOSI
|
|
#define TMC_SW_MOSI PB15
|
|
#endif
|
|
#ifndef TMC_SW_MISO
|
|
#define TMC_SW_MISO PB14
|
|
#endif
|
|
#ifndef TMC_SW_SCK
|
|
#define TMC_SW_SCK PB13
|
|
#endif
|
|
#endif
|
|
|
|
#if HAS_TMC_UART
|
|
/**
|
|
* TMC2208/TMC2209 stepper drivers
|
|
*
|
|
* Hardware serial communication ports.
|
|
* If undefined software serial is used according to the pins below
|
|
*/
|
|
//#define X_HARDWARE_SERIAL Serial1
|
|
//#define X2_HARDWARE_SERIAL Serial1
|
|
//#define Y_HARDWARE_SERIAL Serial1
|
|
//#define Y2_HARDWARE_SERIAL Serial1
|
|
//#define Z_HARDWARE_SERIAL Serial1
|
|
//#define Z2_HARDWARE_SERIAL Serial1
|
|
//#define E0_HARDWARE_SERIAL Serial1
|
|
//#define E1_HARDWARE_SERIAL Serial1
|
|
//#define E2_HARDWARE_SERIAL Serial1
|
|
//#define E3_HARDWARE_SERIAL Serial1
|
|
//#define E4_HARDWARE_SERIAL Serial1
|
|
|
|
//
|
|
// Software serial ##
|
|
//
|
|
#define X_SERIAL_TX_PIN PE2
|
|
#define X_SERIAL_RX_PIN PE2
|
|
|
|
#define Y_SERIAL_TX_PIN PE3
|
|
#define Y_SERIAL_RX_PIN PE3
|
|
|
|
#define Z_SERIAL_TX_PIN PE4
|
|
#define Z_SERIAL_RX_PIN PE4
|
|
|
|
#define E0_SERIAL_TX_PIN PD7
|
|
#define E0_SERIAL_RX_PIN PD7
|
|
|
|
// Reduce baud rate to improve software serial reliability
|
|
#define TMC_BAUD_RATE 19200
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN PA2 // T0 <-> E0
|
|
#define TEMP_1_PIN PA0 // T1 <-> E1
|
|
#define TEMP_BED_PIN PA1 // T2 <-> Bed
|
|
#define TEMP_PROBE_PIN PC3 // Shares J4 connector with PD1
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PE6 // Heater0
|
|
#define HEATER_BED_PIN PE5 // Hotbed
|
|
#define FAN_PIN PB8 // Fan1
|
|
#define FAN1_PIN PB9 // Fan0
|
|
|
|
// HAL SPI1 pins
|
|
#define CUSTOM_SPI_PINS
|
|
#if ENABLED(CUSTOM_SPI_PINS)
|
|
#define SCK_PIN PA5 // SPI1 SCLK
|
|
#define SS_PIN PA4 // SPI1 SSEL
|
|
#define MISO_PIN PA6 // SPI1 MISO
|
|
#define MOSI_PIN PA7 // SPI1 MOSI
|
|
#endif
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
#define SDSS PA4
|
|
|
|
/**
|
|
* -------------------------------------BTT002 V1.0--------------------------------------------
|
|
* ----- ----- |
|
|
* PA3 | · · | GND 5V | · · | GND |
|
|
* NRESET | · · | PC4(SD_DET) (LCD_D7) PE13 | · · | PE12 (LCD_D6) |
|
|
* (MOSI)PA7 | · · | PB0(BTN_EN2) (LCD_D5) PE11 | · · | PE10 (LCD_D4) |
|
|
* (SD_SS)PA4 | · · | PC5(BTN_EN1) (LCD_RS) PE8 | · · | PE9 (LCD_EN) |
|
|
* (SCK)PA5 | · · | PA6(MISO) (BTN_ENC) PB1 | · · | PE7 (BEEPER) |
|
|
* ----- ----- |
|
|
* EXP2 EXP1 |
|
|
* --------------------------------------------------------------------------------------------
|
|
*/
|
|
|
|
//
|
|
// LCDs and Controllers
|
|
//
|
|
#if HAS_WIRED_LCD
|
|
#define BEEPER_PIN PE7
|
|
#define BTN_ENC PB1
|
|
|
|
#if ENABLED(CR10_STOCKDISPLAY)
|
|
#define LCD_PINS_RS PE12
|
|
|
|
#define BTN_EN1 PE9
|
|
#define BTN_EN2 PE10
|
|
|
|
#define LCD_PINS_ENABLE PE13
|
|
#define LCD_PINS_D4 PE11
|
|
|
|
#else
|
|
|
|
#define LCD_PINS_RS PE8
|
|
|
|
#define BTN_EN1 PC5
|
|
#define BTN_EN2 PB0
|
|
#define SD_DETECT_PIN PC4
|
|
|
|
#define LCD_SDSS PA4
|
|
|
|
#define LCD_PINS_ENABLE PE9
|
|
#define LCD_PINS_D4 PE10
|
|
|
|
#if IS_ULTIPANEL
|
|
#define LCD_PINS_D5 PE11
|
|
#define LCD_PINS_D6 PE12
|
|
#define LCD_PINS_D7 PE13
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
|
#define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
// Alter timing for graphical display
|
|
#if HAS_MARLINUI_U8GLIB
|
|
#ifndef BOARD_ST7920_DELAY_1
|
|
#define BOARD_ST7920_DELAY_1 DELAY_NS(96)
|
|
#endif
|
|
#ifndef BOARD_ST7920_DELAY_2
|
|
#define BOARD_ST7920_DELAY_2 DELAY_NS(48)
|
|
#endif
|
|
#ifndef BOARD_ST7920_DELAY_3
|
|
#define BOARD_ST7920_DELAY_3 DELAY_NS(600)
|
|
#endif
|
|
#endif
|
|
|
|
#endif // HAS_WIRED_LCD
|
|
|
|
//
|
|
// RGB LEDs
|
|
//
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN PB5
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN PB4
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN PB3
|
|
#endif
|
|
#ifndef RGB_LED_W_PIN
|
|
#define RGB_LED_W_PIN -1
|
|
#endif
|