Firmware2/Marlin/pins_RAMBO.h
2016-03-24 18:01:20 +00:00

208 lines
4.8 KiB
C

/*
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Rambo pin assignments
*/
#ifndef __AVR_ATmega2560__
#error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu.
#endif
#define LARGE_FLASH true
// Servo support
#define SERVO0_PIN 22 // Motor header MX1
#define SERVO1_PIN 23 // Motor header MX2
#define SERVO2_PIN 24 // Motor header MX3
#define SERVO3_PIN 5 // PWM header pin 5
#if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1
#endif
#undef X_MS1_PIN
#undef X_MS2_PIN
#undef Y_MS1_PIN
#undef Y_MS2_PIN
#undef Z_MS1_PIN
#undef Z_MS2_PIN
#undef E0_MS1_PIN
#undef E0_MS2_PIN
#undef E1_MS1_PIN
#undef E1_MS2_PIN
#define X_STEP_PIN 37
#define X_DIR_PIN 48
#define X_MIN_PIN 12
#define X_MAX_PIN 24
#define X_ENABLE_PIN 29
#define X_MS1_PIN 40
#define X_MS2_PIN 41
#define Y_STEP_PIN 36
#define Y_DIR_PIN 49
#define Y_MIN_PIN 11
#define Y_MAX_PIN 23
#define Y_ENABLE_PIN 28
#define Y_MS1_PIN 69
#define Y_MS2_PIN 39
#define Z_STEP_PIN 35
#define Z_DIR_PIN 47
#define Z_MIN_PIN 10
#define Z_MAX_PIN 30
#define Z_ENABLE_PIN 27
#define Z_MS1_PIN 68
#define Z_MS2_PIN 67
#define HEATER_BED_PIN 3
#define TEMP_BED_PIN 2
#define HEATER_0_PIN 9
#define TEMP_0_PIN 0
#define HEATER_1_PIN 7
#define TEMP_1_PIN 1
#if ENABLED(BARICUDA)
#define HEATER_2_PIN 6
#else
#define HEATER_2_PIN -1
#endif
#define TEMP_2_PIN -1
#define E0_STEP_PIN 34
#define E0_DIR_PIN 43
#define E0_ENABLE_PIN 26
#define E0_MS1_PIN 65
#define E0_MS2_PIN 66
#define E1_STEP_PIN 33
#define E1_DIR_PIN 42
#define E1_ENABLE_PIN 25
#define E1_MS1_PIN 63
#define E1_MS2_PIN 64
#define DIGIPOTSS_PIN 38
#define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping
#define SDPOWER -1
#define SDSS 53
#define LED_PIN 13
#define FAN_PIN 8
/**********************************************************
Fan Pins
Fan_0 8
Fan_1 6
Fan_2 2
***********************************************************/
#define PS_ON_PIN 4
#define KILL_PIN -1 //80 with Smart Controller LCD
#define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing.
#if ENABLED(ULTRA_LCD)
#define KILL_PIN 80
#if ENABLED(NEWPANEL)
#define BEEPER_PIN 79 // Beeper on AUX-4
#define LCD_PINS_RS 70
#define LCD_PINS_ENABLE 71
#define LCD_PINS_D4 72
#define LCD_PINS_D5 73
#define LCD_PINS_D6 74
#define LCD_PINS_D7 75
//buttons are directly attached using AUX-2
#define BTN_EN1 76
#define BTN_EN2 77
#define BTN_ENC 78 //the click
#define BLEN_C 2
#define BLEN_B 1
#define BLEN_A 0
#define SD_DETECT_PIN 81 // Ramps doesn't use this
#else //!NEWPANEL - old style panel with shift register
#define BEEPER_PIN 33 // No Beeper added
//buttons are attached to a shift register
// Not wired yet
//#define SHIFT_CLK 38
//#define SHIFT_LD 42
//#define SHIFT_OUT 40
//#define SHIFT_EN 17
#define LCD_PINS_RS 75
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 23
#define LCD_PINS_D5 25
#define LCD_PINS_D6 27
#define LCD_PINS_D7 29
//bits in the shift register that carry the buttons for:
// left up center down right red
#define BL_LE 7
#define BL_UP 6
#define BL_MI 5
#define BL_DW 4
#define BL_RI 3
#define BL_ST 2
#define BLEN_B 1
#define BLEN_A 0
#endif // !NEWPANEL
#endif // ULTRA_LCD
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER_PIN 44
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 70
#define DOGLCD_CS 71
#define LCD_SCREEN_ROT_180
//The encoder and click button
#define BTN_EN1 85
#define BTN_EN2 84
#define BTN_ENC 83 //the click switch
#define SD_DETECT_PIN -1 // Pin 72 if using easy adapter board
#if ENABLED(TEMP_STAT_LEDS)
#define STAT_LED_RED 22
#define STAT_LED_BLUE 32
#endif
#endif // VIKI2/miniVIKI
#if ENABLED(FILAMENT_SENSOR)
//Filip added pin for Filament sensor analog input
#define FILWIDTH_PIN 3
#endif