6851909f90
Enables CHECK_ENCODER_ACTIVE_SIGNAL for many more boards. Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com> Co-authored-by: Jason Smith <jason.inet@gmail.com>
240 lines
7.2 KiB
C
240 lines
7.2 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* RAMPS-FD
|
|
*
|
|
* No EEPROM
|
|
* Use 4k7 thermistor tables
|
|
*/
|
|
|
|
#if NOT_TARGET(__SAM3X8E__)
|
|
#error "Oops! Select 'Arduino Due' in 'Tools > Board.'"
|
|
#endif
|
|
|
|
#ifndef BOARD_INFO_NAME
|
|
#define BOARD_INFO_NAME "RAMPS-FD v1"
|
|
#endif
|
|
|
|
#define INVERTED_HEATER_PINS
|
|
#define INVERTED_BED_PINS
|
|
#define INVERTED_FAN_PINS
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
#define SERVO0_PIN 7
|
|
#define SERVO1_PIN 6
|
|
#define SERVO2_PIN 5
|
|
#define SERVO3_PIN 3
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_MIN_PIN 22
|
|
#define X_MAX_PIN 30
|
|
#define Y_MIN_PIN 24
|
|
#define Y_MAX_PIN 38
|
|
#define Z_MIN_PIN 26
|
|
#define Z_MAX_PIN 34
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN 63
|
|
#define X_DIR_PIN 62
|
|
#define X_ENABLE_PIN 48
|
|
#ifndef X_CS_PIN
|
|
#define X_CS_PIN 68
|
|
#endif
|
|
|
|
#define Y_STEP_PIN 65
|
|
#define Y_DIR_PIN 64
|
|
#define Y_ENABLE_PIN 46
|
|
#ifndef Y_CS_PIN
|
|
#define Y_CS_PIN 60
|
|
#endif
|
|
|
|
#define Z_STEP_PIN 67
|
|
#define Z_DIR_PIN 66
|
|
#define Z_ENABLE_PIN 44
|
|
#ifndef Z_CS_PIN
|
|
#define Z_CS_PIN 58
|
|
#endif
|
|
|
|
#define E0_STEP_PIN 36
|
|
#define E0_DIR_PIN 28
|
|
#define E0_ENABLE_PIN 42
|
|
#ifndef E0_CS_PIN
|
|
#define E0_CS_PIN 67
|
|
#endif
|
|
|
|
#define E1_STEP_PIN 43
|
|
#define E1_DIR_PIN 41
|
|
#define E1_ENABLE_PIN 39
|
|
#ifndef E1_CS_PIN
|
|
#define E1_CS_PIN 61
|
|
#endif
|
|
|
|
#define E2_STEP_PIN 32
|
|
#define E2_DIR_PIN 47
|
|
#define E2_ENABLE_PIN 45
|
|
#ifndef E2_CS_PIN
|
|
#define E2_CS_PIN 59
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN 1 // Analog Input
|
|
#define TEMP_1_PIN 2 // Analog Input
|
|
#define TEMP_2_PIN 3 // Analog Input
|
|
#define TEMP_BED_PIN 0 // Analog Input
|
|
|
|
// SPI for Max6675 or Max31855 Thermocouple
|
|
#if DISABLED(SDSUPPORT)
|
|
#define MAX6675_SS_PIN 53
|
|
#else
|
|
#define MAX6675_SS_PIN 49
|
|
#endif
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN 9
|
|
#define HEATER_1_PIN 10
|
|
#define HEATER_2_PIN 11
|
|
#define HEATER_BED_PIN 8
|
|
|
|
#ifndef FAN_PIN
|
|
#define FAN_PIN 12
|
|
#endif
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
#define SDSS 4
|
|
#define LED_PIN 13
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#if HAS_WIRED_LCD
|
|
// ramps-fd lcd adaptor
|
|
|
|
#define BEEPER_PIN 37
|
|
#define BTN_EN1 33
|
|
#define BTN_EN2 31
|
|
#define BTN_ENC 35
|
|
#define SD_DETECT_PIN 49
|
|
|
|
#if IS_NEWPANEL
|
|
#define LCD_PINS_RS 16
|
|
#define LCD_PINS_ENABLE 17
|
|
#endif
|
|
|
|
#if ENABLED(FYSETC_MINI_12864)
|
|
#define DOGLCD_CS LCD_PINS_ENABLE
|
|
#define DOGLCD_A0 LCD_PINS_RS
|
|
#define DOGLCD_SCK 76
|
|
#define DOGLCD_MOSI 75
|
|
|
|
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
|
|
// results in LCD soft SPI mode 3, SD soft SPI mode 0
|
|
|
|
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
|
|
|
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN 25
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN 27
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN 29
|
|
#endif
|
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
|
#define NEOPIXEL_PIN 25
|
|
#endif
|
|
|
|
#elif IS_NEWPANEL
|
|
|
|
#define LCD_PINS_D4 23
|
|
#define LCD_PINS_D5 25
|
|
#define LCD_PINS_D6 27
|
|
#define LCD_PINS_D7 29
|
|
|
|
#if ENABLED(MINIPANEL)
|
|
#define DOGLCD_CS 25
|
|
#define DOGLCD_A0 27
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#if ANY(VIKI2, miniVIKI)
|
|
#define DOGLCD_A0 16
|
|
#define KILL_PIN 51
|
|
#define STAT_LED_BLUE_PIN 29
|
|
#define STAT_LED_RED_PIN 23
|
|
#define DOGLCD_CS 17
|
|
#define DOGLCD_SCK 76 // SCK_PIN - Required for DUE Hardware SPI
|
|
#define DOGLCD_MOSI 75 // MOSI_PIN
|
|
#define DOGLCD_MISO 74 // MISO_PIN
|
|
#endif
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
|
#define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
|
|
#endif
|
|
|
|
#endif // HAS_WIRED_LCD
|
|
|
|
#if HAS_TMC_UART
|
|
/**
|
|
* TMC2208/TMC2209 stepper drivers
|
|
*
|
|
* Hardware serial communication ports.
|
|
* If undefined software serial is used according to the pins below
|
|
*/
|
|
//#define X_HARDWARE_SERIAL Serial1
|
|
//#define X2_HARDWARE_SERIAL Serial1
|
|
//#define Y_HARDWARE_SERIAL Serial1
|
|
//#define Y2_HARDWARE_SERIAL Serial1
|
|
//#define Z_HARDWARE_SERIAL Serial1
|
|
//#define Z2_HARDWARE_SERIAL Serial1
|
|
//#define E0_HARDWARE_SERIAL Serial1
|
|
//#define E1_HARDWARE_SERIAL Serial1
|
|
//#define E2_HARDWARE_SERIAL Serial1
|
|
//#define E3_HARDWARE_SERIAL Serial1
|
|
//#define E4_HARDWARE_SERIAL Serial1
|
|
#endif
|
|
|
|
//
|
|
// M3/M4/M5 - Spindle/Laser Control
|
|
//
|
|
#if HOTENDS < 3 && HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA)
|
|
#define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA
|
|
#define SPINDLE_LASER_PWM_PIN 12 // Hardware PWM
|
|
#define SPINDLE_DIR_PIN 47 // Use E2 DIR
|
|
#endif
|