259 lines
6.2 KiB
C
259 lines
6.2 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
* Ported sys0724 & Vynt
|
|
*/
|
|
|
|
/**
|
|
* Arduino Mega? or Due with RuRAMPS4DUE pin assignments
|
|
*
|
|
* Applies to the following boards:
|
|
* RURAMPS4DUE (Hotend0, Hotend1, Hotend2, Fan0, Fan1, Bed)
|
|
*
|
|
* Differences between
|
|
* RADDS | RuRAMPS4DUE
|
|
* |
|
|
*/
|
|
|
|
#ifndef __SAM3X8E__
|
|
#error "Oops! Select 'Arduino Due' in 'Tools > Board.'"
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "RuRAMPS4Due v1.3"
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
#define SERVO0_PIN 5
|
|
#define SERVO1_PIN 3
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_MIN_PIN 45
|
|
#define X_MAX_PIN 39
|
|
#define Y_MIN_PIN 46
|
|
#define Y_MAX_PIN 41
|
|
#define Z_MIN_PIN 47
|
|
#define Z_MAX_PIN 43
|
|
|
|
//
|
|
// Z Probe (when not Z_MIN_PIN)
|
|
//
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
#define Z_MIN_PROBE_PIN 49
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN 37 // Support Extension Board
|
|
#define X_DIR_PIN 36
|
|
#define X_ENABLE_PIN 31
|
|
#ifndef X_CS_PIN
|
|
#define X_CS_PIN 38
|
|
#endif
|
|
|
|
#define Y_STEP_PIN 32 // Support Extension Board
|
|
#define Y_DIR_PIN 35
|
|
#define Y_ENABLE_PIN 31
|
|
#ifndef Y_CS_PIN
|
|
#define Y_CS_PIN 34
|
|
#endif
|
|
|
|
#define Z_STEP_PIN 30 // Support Extension Board
|
|
#define Z_DIR_PIN 2
|
|
#define Z_ENABLE_PIN 31
|
|
#ifndef Z_CS_PIN
|
|
#define Z_CS_PIN 10
|
|
#endif
|
|
|
|
#define E0_STEP_PIN 29
|
|
#define E0_DIR_PIN 28
|
|
#define E0_ENABLE_PIN 33
|
|
#ifndef E0_CS_PIN
|
|
#define E0_CS_PIN 14
|
|
#endif
|
|
|
|
#define E1_STEP_PIN 22
|
|
#define E1_DIR_PIN 24
|
|
#define E1_ENABLE_PIN 26
|
|
#ifndef E1_CS_PIN
|
|
#define E1_CS_PIN 15
|
|
#endif
|
|
|
|
#define E2_STEP_PIN 25
|
|
#define E2_DIR_PIN 23
|
|
#define E2_ENABLE_PIN 27
|
|
#ifndef E2_CS_PIN
|
|
#define E2_CS_PIN 61
|
|
#endif
|
|
|
|
#if USES_Z_MIN_PROBE_ENDSTOP
|
|
#define Z_MIN_PROBE_PIN 49
|
|
#endif
|
|
|
|
#if HAS_FILAMENT_SENSOR
|
|
#ifndef FIL_RUNOUT_PIN
|
|
#define FIL_RUNOUT_PIN Y_MIN_PIN
|
|
#endif
|
|
#endif
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN 13
|
|
#define HEATER_1_PIN 12
|
|
#define HEATER_2_PIN 11
|
|
#define HEATER_BED_PIN 7 // BED H1
|
|
|
|
#define FAN_PIN 9
|
|
#define FAN1_PIN 8
|
|
#define CONTROLLER_FAN_PIN -1
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN 0 // ANALOG A0
|
|
#define TEMP_1_PIN 1 // ANALOG A1
|
|
#define TEMP_2_PIN 2 // ANALOG A2
|
|
#define TEMP_3_PIN 3 // ANALOG A3
|
|
#define TEMP_BED_PIN 4 // ANALOG A4
|
|
|
|
// The thermocouple uses Analog pins
|
|
#if ENABLED(VER_WITH_THERMOCOUPLE) // Defined in Configuration.h
|
|
#define TEMP_4_PIN 5 // A5
|
|
#define TEMP_5_PIN 6 // A6 (Marlin 2.0 not support)
|
|
#endif
|
|
|
|
// SPI for Max6675 or Max31855 Thermocouple
|
|
/*
|
|
#if DISABLED(SDSUPPORT)
|
|
#define MAX6675_SS_PIN 53
|
|
#else
|
|
#define MAX6675_SS_PIN 49
|
|
#endif
|
|
*/
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
#define SDSS 4 // 4,10,52 if using HW SPI.
|
|
#define LED_PIN -1 // 13 - HEATER_0_PIN
|
|
#define PS_ON_PIN -1 // 65
|
|
|
|
// MKS TFT / Nextion Use internal USART-1
|
|
#define TFT_LCD_MODULE_COM 1
|
|
#define TFT_LCD_MODULE_BAUDRATE 115200
|
|
|
|
// ESP WiFi Use internal USART-2
|
|
#define ESP_WIFI_MODULE_COM 2
|
|
#define ESP_WIFI_MODULE_BAUDRATE 115200
|
|
#define ESP_WIFI_MODULE_RESET_PIN -1
|
|
#define PIGGY_GPIO_PIN -1
|
|
|
|
//
|
|
// EEPROM
|
|
//
|
|
#define E2END 0x7FFF // 32Kb (24lc256)
|
|
#define I2C_EEPROM // EEPROM on I2C-0
|
|
//#define EEPROM_SD // EEPROM on SDCARD
|
|
//#define SPI_EEPROM // EEPROM on SPI-0
|
|
//#define SPI_CHAN_EEPROM1 ?
|
|
//#define SPI_EEPROM1_CS ?
|
|
// 2K EEPROM
|
|
//#define SPI_EEPROM2_CS ?
|
|
// 32Mb FLASH
|
|
//#define SPI_FLASH_CS ?
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#if HAS_SPI_LCD
|
|
|
|
#if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
|
#define BEEPER_PIN 62
|
|
#define LCD_PINS_D4 48
|
|
#define LCD_PINS_D5 50
|
|
#define LCD_PINS_D6 52
|
|
#define LCD_PINS_D7 53
|
|
#define SD_DETECT_PIN 51
|
|
#endif
|
|
|
|
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
|
|
|
|
#define LCD_PINS_RS 63
|
|
#define LCD_PINS_ENABLE 64
|
|
|
|
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
|
|
|
#define LCD_PINS_RS 52
|
|
#define LCD_PINS_ENABLE 53
|
|
|
|
#elif HAS_SSD1306_OLED_I2C
|
|
|
|
#define BEEPER_PIN 62
|
|
#define LCD_SDSS 10
|
|
#define SD_DETECT_PIN 51
|
|
|
|
#elif ENABLED(FYSETC_MINI_12864)
|
|
|
|
#define BEEPER_PIN 62
|
|
#define DOGLCD_CS 64
|
|
#define DOGLCD_A0 63
|
|
|
|
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
|
|
// results in LCD soft SPI mode 3, SD soft SPI mode 0
|
|
|
|
#define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally.
|
|
|
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN 50 // D5
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN 52 // D6
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN 53 // D7
|
|
#endif
|
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
|
#define NEOPIXEL_PIN 50 // D5
|
|
#endif
|
|
|
|
#elif ENABLED(MKS_MINI_12864)
|
|
|
|
#define ORIG_BEEPER_PIN 62
|
|
|
|
#define DOGLCD_A0 52
|
|
#define DOGLCD_CS 50
|
|
|
|
#define SD_DETECT_PIN 51
|
|
|
|
#endif
|
|
|
|
#if ENABLED(NEWPANEL)
|
|
#define BTN_EN1 44
|
|
#define BTN_EN2 42
|
|
#define BTN_ENC 40
|
|
#endif
|
|
|
|
#endif // HAS_SPI_LCD
|