Firmware2/Marlin/src/pins/sam/pins_RURAMPS4D_13.h
Scott Lahteine bfad23d3e2 (c) 2020
2020-02-03 08:00:57 -06:00

259 lines
6.2 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
* Ported sys0724 & Vynt
*/
/**
* Arduino Mega? or Due with RuRAMPS4DUE pin assignments
*
* Applies to the following boards:
* RURAMPS4DUE (Hotend0, Hotend1, Hotend2, Fan0, Fan1, Bed)
*
* Differences between
* RADDS | RuRAMPS4DUE
* |
*/
#ifndef __SAM3X8E__
#error "Oops! Select 'Arduino Due' in 'Tools > Board.'"
#endif
#define BOARD_INFO_NAME "RuRAMPS4Due v1.3"
//
// Servos
//
#define SERVO0_PIN 5
#define SERVO1_PIN 3
//
// Limit Switches
//
#define X_MIN_PIN 45
#define X_MAX_PIN 39
#define Y_MIN_PIN 46
#define Y_MAX_PIN 41
#define Z_MIN_PIN 47
#define Z_MAX_PIN 43
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 49
#endif
//
// Steppers
//
#define X_STEP_PIN 37 // Support Extension Board
#define X_DIR_PIN 36
#define X_ENABLE_PIN 31
#ifndef X_CS_PIN
#define X_CS_PIN 38
#endif
#define Y_STEP_PIN 32 // Support Extension Board
#define Y_DIR_PIN 35
#define Y_ENABLE_PIN 31
#ifndef Y_CS_PIN
#define Y_CS_PIN 34
#endif
#define Z_STEP_PIN 30 // Support Extension Board
#define Z_DIR_PIN 2
#define Z_ENABLE_PIN 31
#ifndef Z_CS_PIN
#define Z_CS_PIN 10
#endif
#define E0_STEP_PIN 29
#define E0_DIR_PIN 28
#define E0_ENABLE_PIN 33
#ifndef E0_CS_PIN
#define E0_CS_PIN 14
#endif
#define E1_STEP_PIN 22
#define E1_DIR_PIN 24
#define E1_ENABLE_PIN 26
#ifndef E1_CS_PIN
#define E1_CS_PIN 15
#endif
#define E2_STEP_PIN 25
#define E2_DIR_PIN 23
#define E2_ENABLE_PIN 27
#ifndef E2_CS_PIN
#define E2_CS_PIN 61
#endif
#if HAS_CUSTOM_PROBE_PIN
#define Z_MIN_PROBE_PIN 49
#endif
#if HAS_FILAMENT_SENSOR
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN Y_MIN_PIN
#endif
#endif
//
// Heaters / Fans
//
#define HEATER_0_PIN 13
#define HEATER_1_PIN 12
#define HEATER_2_PIN 11
#define HEATER_BED_PIN 7 // BED H1
#define FAN_PIN 9
#define FAN1_PIN 8
#define CONTROLLER_FAN_PIN -1
//
// Temperature Sensors
//
#define TEMP_0_PIN 0 // ANALOG A0
#define TEMP_1_PIN 1 // ANALOG A1
#define TEMP_2_PIN 2 // ANALOG A2
#define TEMP_3_PIN 3 // ANALOG A3
#define TEMP_BED_PIN 4 // ANALOG A4
// The thermocouple uses Analog pins
#if ENABLED(VER_WITH_THERMOCOUPLE) // Defined in Configuration.h
#define TEMP_4_PIN 5 // A5
#define TEMP_5_PIN 6 // A6 (Marlin 2.0 not support)
#endif
// SPI for Max6675 or Max31855 Thermocouple
/*
#if DISABLED(SDSUPPORT)
#define MAX6675_SS_PIN 53
#else
#define MAX6675_SS_PIN 49
#endif
*/
//
// Misc. Functions
//
#define SDSS 4 // 4,10,52 if using HW SPI.
#define LED_PIN -1 // 13 - HEATER_0_PIN
#define PS_ON_PIN -1 // 65
// MKS TFT / Nextion Use internal USART-1
#define TFT_LCD_MODULE_COM 1
#define TFT_LCD_MODULE_BAUDRATE 115200
// ESP WiFi Use internal USART-2
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1
#define PIGGY_GPIO_PIN -1
//
// EEPROM
//
#define E2END 0x7FFF // 32Kb (24lc256)
#define I2C_EEPROM // EEPROM on I2C-0
//#define EEPROM_SD // EEPROM on SDCARD
//#define SPI_EEPROM // EEPROM on SPI-0
//#define SPI_CHAN_EEPROM1 ?
//#define SPI_EEPROM1_CS ?
// 2K EEPROM
//#define SPI_EEPROM2_CS ?
// 32Mb FLASH
//#define SPI_FLASH_CS ?
//
// LCD / Controller
//
#if HAS_SPI_LCD
#if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define BEEPER_PIN 62
#define LCD_PINS_D4 48
#define LCD_PINS_D5 50
#define LCD_PINS_D6 52
#define LCD_PINS_D7 53
#define SD_DETECT_PIN 51
#endif
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
#define LCD_PINS_RS 63
#define LCD_PINS_ENABLE 64
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define LCD_PINS_RS 52
#define LCD_PINS_ENABLE 53
#elif HAS_SSD1306_OLED_I2C
#define BEEPER_PIN 62
#define LCD_SDSS 10
#define SD_DETECT_PIN 51
#elif ENABLED(FYSETC_MINI_12864)
#define BEEPER_PIN 62
#define DOGLCD_CS 64
#define DOGLCD_A0 63
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
// results in LCD soft SPI mode 3, SD soft SPI mode 0
#define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally.
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN 50 // D5
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN 52 // D6
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN 53 // D7
#endif
#elif ENABLED(FYSETC_MINI_12864_2_1)
#define NEOPIXEL_PIN 50 // D5
#endif
#elif ENABLED(MKS_MINI_12864)
#define ORIG_BEEPER_PIN 62
#define DOGLCD_A0 52
#define DOGLCD_CS 50
#define SD_DETECT_PIN 51
#endif
#if ENABLED(NEWPANEL)
#define BTN_EN1 44
#define BTN_EN2 42
#define BTN_ENC 40
#endif
#endif // HAS_SPI_LCD