Firmware2/Marlin/src/HAL/HAL_STM32F1/HAL.cpp
2019-11-12 22:16:54 -06:00

375 lines
12 KiB
C++

/**
* Marlin 3D Printer Firmware
*
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* Copyright (c) 2016 Bob Cousins bobcousins42@googlemail.com
* Copyright (c) 2015-2016 Nico Tonnhofer wurstnase.reprap@gmail.com
* Copyright (c) 2017 Victor Perez
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* HAL for stm32duino.com based on Libmaple and compatible (STM32F1)
*/
#ifdef __STM32F1__
#include "../../inc/MarlinConfig.h"
#include "HAL.h"
#include <STM32ADC.h>
// ------------------------
// Types
// ------------------------
#define __I
#define __IO volatile
typedef struct {
__I uint32_t CPUID; /*!< Offset: 0x000 (R/ ) CPUID Base Register */
__IO uint32_t ICSR; /*!< Offset: 0x004 (R/W) Interrupt Control and State Register */
__IO uint32_t VTOR; /*!< Offset: 0x008 (R/W) Vector Table Offset Register */
__IO uint32_t AIRCR; /*!< Offset: 0x00C (R/W) Application Interrupt and Reset Control Register */
__IO uint32_t SCR; /*!< Offset: 0x010 (R/W) System Control Register */
__IO uint32_t CCR; /*!< Offset: 0x014 (R/W) Configuration Control Register */
__IO uint8_t SHP[12]; /*!< Offset: 0x018 (R/W) System Handlers Priority Registers (4-7, 8-11, 12-15) */
__IO uint32_t SHCSR; /*!< Offset: 0x024 (R/W) System Handler Control and State Register */
__IO uint32_t CFSR; /*!< Offset: 0x028 (R/W) Configurable Fault Status Register */
__IO uint32_t HFSR; /*!< Offset: 0x02C (R/W) HardFault Status Register */
__IO uint32_t DFSR; /*!< Offset: 0x030 (R/W) Debug Fault Status Register */
__IO uint32_t MMFAR; /*!< Offset: 0x034 (R/W) MemManage Fault Address Register */
__IO uint32_t BFAR; /*!< Offset: 0x038 (R/W) BusFault Address Register */
__IO uint32_t AFSR; /*!< Offset: 0x03C (R/W) Auxiliary Fault Status Register */
__I uint32_t PFR[2]; /*!< Offset: 0x040 (R/ ) Processor Feature Register */
__I uint32_t DFR; /*!< Offset: 0x048 (R/ ) Debug Feature Register */
__I uint32_t ADR; /*!< Offset: 0x04C (R/ ) Auxiliary Feature Register */
__I uint32_t MMFR[4]; /*!< Offset: 0x050 (R/ ) Memory Model Feature Register */
__I uint32_t ISAR[5]; /*!< Offset: 0x060 (R/ ) Instruction Set Attributes Register */
uint32_t RESERVED0[5];
__IO uint32_t CPACR; /*!< Offset: 0x088 (R/W) Coprocessor Access Control Register */
} SCB_Type;
// ------------------------
// Local defines
// ------------------------
#define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */
#define SCB_BASE (SCS_BASE + 0x0D00UL) /*!< System Control Block Base Address */
#define SCB ((SCB_Type *) SCB_BASE ) /*!< SCB configuration struct */
/* SCB Application Interrupt and Reset Control Register Definitions */
#define SCB_AIRCR_VECTKEY_Pos 16 /*!< SCB AIRCR: VECTKEY Position */
#define SCB_AIRCR_VECTKEY_Msk (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos) /*!< SCB AIRCR: VECTKEY Mask */
#define SCB_AIRCR_PRIGROUP_Pos 8 /*!< SCB AIRCR: PRIGROUP Position */
#define SCB_AIRCR_PRIGROUP_Msk (7UL << SCB_AIRCR_PRIGROUP_Pos) /*!< SCB AIRCR: PRIGROUP Mask */
// ------------------------
// Public Variables
// ------------------------
#if (defined(SERIAL_USB) && !defined(USE_USB_COMPOSITE))
USBSerial SerialUSB;
#endif
uint16_t HAL_adc_result;
// ------------------------
// Private Variables
// ------------------------
STM32ADC adc(ADC1);
const uint8_t adc_pins[] = {
#if HAS_TEMP_ADC_0
TEMP_0_PIN,
#endif
#if HAS_HEATED_BED
TEMP_BED_PIN,
#endif
#if HAS_HEATED_CHAMBER
TEMP_CHAMBER_PIN,
#endif
#if HAS_TEMP_ADC_1
TEMP_1_PIN,
#endif
#if HAS_TEMP_ADC_2
TEMP_2_PIN,
#endif
#if HAS_TEMP_ADC_3
TEMP_3_PIN,
#endif
#if HAS_TEMP_ADC_4
TEMP_4_PIN,
#endif
#if HAS_TEMP_ADC_5
TEMP_5_PIN,
#endif
#if ENABLED(FILAMENT_WIDTH_SENSOR)
FILWIDTH_PIN,
#endif
#if HAS_JOY_ADC_X
JOY_X_PIN,
#endif
#if HAS_JOY_ADC_Y
JOY_Y_PIN,
#endif
#if HAS_JOY_ADC_Z
JOY_Z_PIN,
#endif
};
enum TEMP_PINS : char {
#if HAS_TEMP_ADC_0
TEMP_0,
#endif
#if HAS_HEATED_BED
TEMP_BED,
#endif
#if HAS_HEATED_CHAMBER
TEMP_CHAMBER,
#endif
#if HAS_TEMP_ADC_1
TEMP_1,
#endif
#if HAS_TEMP_ADC_2
TEMP_2,
#endif
#if HAS_TEMP_ADC_3
TEMP_3,
#endif
#if HAS_TEMP_ADC_4
TEMP_4,
#endif
#if HAS_TEMP_ADC_5
TEMP_5,
#endif
#if ENABLED(FILAMENT_WIDTH_SENSOR)
FILWIDTH,
#endif
#if HAS_JOY_ADC_X
JOY_X,
#endif
#if HAS_JOY_ADC_Y
JOY_Y,
#endif
#if HAS_JOY_ADC_Z
JOY_Z,
#endif
ADC_PIN_COUNT
};
uint16_t HAL_adc_results[ADC_PIN_COUNT];
// ------------------------
// Private functions
// ------------------------
static void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) {
uint32_t reg_value;
uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07); /* only values 0..7 are used */
reg_value = SCB->AIRCR; /* read old register configuration */
reg_value &= ~(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk); /* clear bits to change */
reg_value = (reg_value |
((uint32_t)0x5FA << SCB_AIRCR_VECTKEY_Pos) |
(PriorityGroupTmp << 8)); /* Insert write key and priorty group */
SCB->AIRCR = reg_value;
}
// ------------------------
// Public functions
// ------------------------
//
// Leave PA11/PA12 intact if USBSerial is not used
//
#if SERIAL_USB
namespace wirish { namespace priv {
#if SERIAL_PORT > 0
#if SERIAL_PORT2
#if SERIAL_PORT2 > 0
void board_setup_usb() {}
#endif
#else
void board_setup_usb() {}
#endif
#endif
} }
#endif
void HAL_init() {
NVIC_SetPriorityGrouping(0x3);
#if PIN_EXISTS(LED)
OUT_WRITE(LED_PIN, LOW);
#endif
#ifdef USE_USB_COMPOSITE
MSC_SD_init();
#endif
#if PIN_EXISTS(USB_CONNECT)
OUT_WRITE(USB_CONNECT_PIN, !USB_CONNECT_INVERTING); // USB clear connection
delay(1000); // Give OS time to notice
OUT_WRITE(USB_CONNECT_PIN, USB_CONNECT_INVERTING);
#endif
}
// HAL idle task
void HAL_idletask() {
#ifdef USE_USB_COMPOSITE
#if ENABLED(SHARED_SD_CARD)
// If Marlin is using the SD card we need to lock it to prevent access from
// a PC via USB.
// Other HALs use IS_SD_PRINTING() and IS_SD_FILE_OPEN() to check for access but
// this will not reliably detect delete operations. To be safe we will lock
// the disk if Marlin has it mounted. Unfortunately there is currently no way
// to unmount the disk from the LCD menu.
// if (IS_SD_PRINTING() || IS_SD_FILE_OPEN())
/* copy from lpc1768 framework, should be fixed later for process SHARED_SD_CARD*/
#endif
// process USB mass storage device class loop
MarlinMSC.loop();
#endif
}
/* VGPV Done with defines
// disable interrupts
void cli() { noInterrupts(); }
// enable interrupts
void sei() { interrupts(); }
*/
void HAL_clear_reset_source() { }
/**
* TODO: Check this and change or remove.
* currently returns 1 that's equal to poweron reset.
*/
uint8_t HAL_get_reset_source() { return 1; }
void _delay_ms(const int delay_ms) { delay(delay_ms); }
extern "C" {
extern unsigned int _ebss; // end of bss section
}
/**
* TODO: Change this to correct it for libmaple
*/
// return free memory between end of heap (or end bss) and whatever is current
/*
#include <wirish/syscalls.c>
//extern caddr_t _sbrk(int incr);
#ifndef CONFIG_HEAP_END
extern char _lm_heap_end;
#define CONFIG_HEAP_END ((caddr_t)&_lm_heap_end)
#endif
extern "C" {
static int freeMemory() {
char top = 't';
return &top - reinterpret_cast<char*>(sbrk(0));
}
int freeMemory() {
int free_memory;
int heap_end = (int)_sbrk(0);
free_memory = ((int)&free_memory) - ((int)heap_end);
return free_memory;
}
}
*/
// ------------------------
// ADC
// ------------------------
// Init the AD in continuous capture mode
void HAL_adc_init() {
// configure the ADC
adc.calibrate();
#if F_CPU > 72000000
adc.setSampleRate(ADC_SMPR_71_5); // 71.5 ADC cycles
#else
adc.setSampleRate(ADC_SMPR_41_5); // 41.5 ADC cycles
#endif
adc.setPins((uint8_t *)adc_pins, ADC_PIN_COUNT);
adc.setDMA(HAL_adc_results, (uint16_t)ADC_PIN_COUNT, (uint32_t)(DMA_MINC_MODE | DMA_CIRC_MODE), nullptr);
adc.setScanMode();
adc.setContinuous();
adc.startConversion();
}
void HAL_adc_start_conversion(const uint8_t adc_pin) {
TEMP_PINS pin_index;
switch (adc_pin) {
default: return;
#if HAS_TEMP_ADC_0
case TEMP_0_PIN: pin_index = TEMP_0; break;
#endif
#if HAS_HEATED_BED
case TEMP_BED_PIN: pin_index = TEMP_BED; break;
#endif
#if HAS_HEATED_CHAMBER
case TEMP_CHAMBER_PIN: pin_index = TEMP_CHAMBER; break;
#endif
#if HAS_TEMP_ADC_1
case TEMP_1_PIN: pin_index = TEMP_1; break;
#endif
#if HAS_TEMP_ADC_2
case TEMP_2_PIN: pin_index = TEMP_2; break;
#endif
#if HAS_TEMP_ADC_3
case TEMP_3_PIN: pin_index = TEMP_3; break;
#endif
#if HAS_TEMP_ADC_4
case TEMP_4_PIN: pin_index = TEMP_4; break;
#endif
#if HAS_TEMP_ADC_5
case TEMP_5_PIN: pin_index = TEMP_5; break;
#endif
#if HAS_JOY_ADC_X
case JOY_X_PIN: pin_index = JOY_X; break;
#endif
#if HAS_JOY_ADC_Y
case JOY_Y_PIN: pin_index = JOY_Y; break;
#endif
#if HAS_JOY_ADC_Z
case JOY_Z_PIN: pin_index = JOY_Z; break;
#endif
#if ENABLED(FILAMENT_WIDTH_SENSOR)
case FILWIDTH_PIN: pin_index = FILWIDTH; break;
#endif
}
HAL_adc_result = (HAL_adc_results[(int)pin_index] >> 2) & 0x3FF; // shift to get 10 bits only.
}
uint16_t HAL_adc_get_result() { return HAL_adc_result; }
uint16_t analogRead(pin_t pin) {
const bool is_analog = _GET_MODE(pin) == GPIO_INPUT_ANALOG;
return is_analog ? analogRead(uint8_t(pin)) : 0;
}
// Wrapper to maple unprotected analogWrite
void analogWrite(pin_t pin, int pwm_val8) {
if (PWM_PIN(pin))
analogWrite(uint8_t(pin), pwm_val8);
}
void flashFirmware(int16_t value) { nvic_sys_reset(); }
#endif // __STM32F1__