Firmware2/Marlin/src/pins/stm32/pins_BIGTREE_BTT002_V1.0.h
2019-08-20 19:10:36 -05:00

255 lines
6.5 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#pragma once
#ifndef TARGET_STM32F4
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
#elif HOTENDS > 3 || E_STEPPERS > 3
#error "BIGTREE SKR Pro V1.1 supports up to 3 hotends / E-steppers."
#endif
#define BOARD_INFO_NAME "BIGTREE Btt002 1.0"
#define SRAM_EEPROM_EMULATION
// Ignore temp readings during development.
//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
//
// Servos
//
#define SERVO0_PIN PC3
//
// Limit Switches
//
#define X_MIN_PIN PD3
#define X_MAX_PIN PD3
#define Y_MIN_PIN PD2
#define Y_MAX_PIN PD2
#define Z_MIN_PIN PD1
#define Z_MAX_PIN PD1
//
// Z Probe must be this pins ##
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN PD1
#endif
//
// Steppers
//
#define X_STEP_PIN PA9
#define X_DIR_PIN PA10
#define X_ENABLE_PIN PA8
#ifndef X_CS_PIN
#define X_CS_PIN PE2
#endif
#define Y_STEP_PIN PC8
#define Y_DIR_PIN PC9
#define Y_ENABLE_PIN PC7
#ifndef Y_CS_PIN
#define Y_CS_PIN PE3
#endif
#define Z_STEP_PIN PD15
#define Z_DIR_PIN PC6
#define Z_ENABLE_PIN PD14
#ifndef Z_CS_PIN
#define Z_CS_PIN PE4
#endif
#define E0_STEP_PIN PD12
#define E0_DIR_PIN PD13
#define E0_ENABLE_PIN PD11
#ifndef E0_CS_PIN
#define E0_CS_PIN PD7
#endif
/*
//SKR_PRO_V1.1
#define E1_STEP_PIN PD15
#define E1_DIR_PIN PE7
#define E1_ENABLE_PIN PA3
#ifndef E1_CS_PIN
#define E1_CS_PIN PG15
#endif
#define E2_STEP_PIN PD13
#define E2_DIR_PIN PG9
#define E2_ENABLE_PIN PF0
#ifndef E2_CS_PIN
#define E2_CS_PIN PG12
#endif
*/
//
// Software SPI pins for TMC2130 stepper drivers
//
#if ENABLED(TMC_USE_SW_SPI)
#ifndef TMC_SW_MOSI
#define TMC_SW_MOSI PB15
#endif
#ifndef TMC_SW_MISO
#define TMC_SW_MISO PB14
#endif
#ifndef TMC_SW_SCK
#define TMC_SW_SCK PB13
#endif
#endif
#if HAS_TMC220x
/**
* TMC2208/TMC2209 stepper drivers
*
* Hardware serial communication ports.
* If undefined software serial is used according to the pins below
*/
//#define X_HARDWARE_SERIAL Serial1
//#define X2_HARDWARE_SERIAL Serial1
//#define Y_HARDWARE_SERIAL Serial1
//#define Y2_HARDWARE_SERIAL Serial1
//#define Z_HARDWARE_SERIAL Serial1
//#define Z2_HARDWARE_SERIAL Serial1
//#define E0_HARDWARE_SERIAL Serial1
//#define E1_HARDWARE_SERIAL Serial1
//#define E2_HARDWARE_SERIAL Serial1
//#define E3_HARDWARE_SERIAL Serial1
//#define E4_HARDWARE_SERIAL Serial1
//
// Software serial ##
//
#define X_SERIAL_TX_PIN PE2
#define X_SERIAL_RX_PIN PE2
#define Y_SERIAL_TX_PIN PE3
#define Y_SERIAL_RX_PIN PE3
#define Z_SERIAL_TX_PIN PE4
#define Z_SERIAL_RX_PIN PE4
#define E0_SERIAL_TX_PIN PD7
#define E0_SERIAL_RX_PIN PD7
//#define E1_SERIAL_TX_PIN PD1
//#define E1_SERIAL_RX_PIN PD1
//#define E2_SERIAL_TX_PIN PD6
//#define E2_SERIAL_RX_PIN PD6
#endif
//
// Temperature Sensors
//
#define TEMP_0_PIN PA2 // T1 <-> E0
#define TEMP_1_PIN PA0 // T2 <-> E1
//#define TEMP_2_PIN PC2 // T3 <-> E2 SKR_PRO
#define TEMP_BED_PIN PA1 // T0 <-> Bed
//
// Heaters / Fans
//
#define HEATER_0_PIN PE6 // Heater0
//#define HEATER_1_PIN PD14 // Heater1
//#define HEATER_2_PIN PB0 // Heater1
#define HEATER_BED_PIN PE5 // Hotbed
#define FAN_PIN PB9 // Fan0
#define FAN1_PIN PB8 // Fan1
//#define FAN2_PIN PE6 // Fan2
// HAL SPI pins group
#define SCK_PIN PA5 // SPI SCLK
#define MYSSEL PA4 // SPI SSEL
#define MISO_PIN PA6 // SPI MISO
#define MOSI_PIN PA7 // SPI MOSI
//
// Misc. Functions
//
#define SDSS PA4
/**
* -------------------------------------SKR_MK3-----------------------------------------------
* _____ _____ |
* PA3 | · · | GND 5V | · · | GND |
* NRESET | · · | PC4(SD_DET) (LCD_D7) PE13 | · · | PE12 (LCD_D6) |
* (MOSI)PA7 | · · | PB0(BTN_EN2) (LCD_D5) PE11 | · · | PE10 (LCD_D4) |
* (SD_SS)PA4 | · · | PC5(BTN_EN1) (LCD_RS) PE8 | · · | PE9 (LCD_EN) |
* (SCK)PA5 | · · | PA6(MISO) (BTN_ENC) PB1 | · · | PE7 (BEEPER) |
*  ̄ ̄  ̄ ̄ |
* EXP2 EXP1 |
* ---------------------------------------------------------------------------------------------
*/
//
// LCDs and Controllers
//
#if HAS_SPI_LCD
#define BEEPER_PIN PE7
#define BTN_ENC PB1
#if ENABLED(CR10_STOCKDISPLAY)
#define LCD_PINS_RS PE12
#define BTN_EN1 PE9
#define BTN_EN2 PE10
#define LCD_PINS_ENABLE PE13
#define LCD_PINS_D4 PE11
#else
#define LCD_PINS_RS PE8
#define BTN_EN1 PC5
#define BTN_EN2 PB0
#define SD_DETECT_PIN PC4
#define LCD_SDSS PA4
#define LCD_PINS_ENABLE PE9
#define LCD_PINS_D4 PE10
#if ENABLED(ULTIPANEL)
#define LCD_PINS_D5 PE11
#define LCD_PINS_D6 PE12
#define LCD_PINS_D7 PE13
#endif
#endif
// Alter timing for graphical display
#if HAS_GRAPHICAL_LCD
#ifndef ST7920_DELAY_1
#define ST7920_DELAY_1 DELAY_NS(96)
#endif
#ifndef ST7920_DELAY_2
#define ST7920_DELAY_2 DELAY_NS(48)
#endif
#ifndef ST7920_DELAY_3
#define ST7920_DELAY_3 DELAY_NS(600)
#endif
#endif
#endif // HAS_SPI_LCD