Firmware2/Marlin/pins_AZTEEG_X3.h
2017-05-17 04:23:06 -05:00

101 lines
2.6 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* AZTEEG_X3 Arduino Mega with RAMPS v1.4 pin assignments
*/
#ifndef __AVR_ATmega2560__
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
#endif
#if HOTENDS > 2 || E_STEPPERS > 2
#error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue."
#endif
#define BOARD_NAME "Azteeg X3"
#if !PIN_EXISTS(CASE_LIGHT) // doesn't already exist so OK to change the definition coming
#define OK_TO_CHANGE_CASE_LIGHT // in from from the include file
#endif
#include "pins_RAMPS_13.h"
//
// Servos
//
#undef SERVO0_PIN
#undef SERVO1_PIN
#define SERVO0_PIN 44 // SERVO1 port
#define SERVO1_PIN 55 // SERVO2 port
//
// LCD / Controller
//
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#undef DOGLCD_A0
#undef DOGLCD_CS
#undef BTN_ENC
#define DOGLCD_A0 31
#define DOGLCD_CS 32
#define BTN_ENC 12
#undef STAT_LED_RED_PIN
#undef STAT_LED_BLUE_PIN
#define STAT_LED_RED_PIN 64
#define STAT_LED_BLUE_PIN 63
#else
#define STAT_LED_RED_PIN 6
#define STAT_LED_BLUE_PIN 11
#endif
//
// Misc
//
#if ENABLED(OK_TO_CHANGE_CASE_LIGHT) && STAT_LED_RED_PIN == 6
#undef STAT_LED_RED_PIN
#undef CASE_LIGHT_PIN
#define CASE_LIGHT_PIN 6 // open collector FET driver
#endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board
#undef SPINDLE_LASER_ENABLE_PIN
#undef SPINDLE_DIR_PIN
#if ENABLED(SPINDLE_LASER_ENABLE)
#undef SDA // use EXP3 header
#undef SCL
#if SERVO0_PIN == 7
#undef SERVO0_PIN
#def SERVO0_PIN 11
#define SPINDLE_LASER_PWM_PIN 7 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 21
#endif