107 lines
2.9 KiB
C++
107 lines
2.9 KiB
C++
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* Copypaste of SAMD51 HAL developed by Giuliano Zaro (AKA GMagician)
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#ifdef ARDUINO_ARCH_ESP32
|
|
|
|
#include "../../inc/MarlinConfig.h"
|
|
|
|
#if EITHER(MKS_MINI_12864, FYSETC_MINI_12864_2_1)
|
|
|
|
#include <U8glib-HAL.h>
|
|
#include "../shared/HAL_SPI.h"
|
|
#include "HAL.h"
|
|
#include "SPI.h"
|
|
|
|
#if ENABLED(SDSUPPORT)
|
|
#include "../../sd/cardreader.h"
|
|
#if ENABLED(ESP3D_WIFISUPPORT)
|
|
#include "sd_ESP32.h"
|
|
#endif
|
|
#endif
|
|
|
|
static SPISettings spiConfig;
|
|
|
|
|
|
#ifndef LCD_SPI_SPEED
|
|
#ifdef SD_SPI_SPEED
|
|
#define LCD_SPI_SPEED SD_SPI_SPEED // Assume SPI speed shared with SD
|
|
#else
|
|
#define LCD_SPI_SPEED SPI_FULL_SPEED // Use full speed if SD speed is not supplied
|
|
#endif
|
|
#endif
|
|
|
|
uint8_t u8g_eps_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {
|
|
static uint8_t msgInitCount = 2; // Ignore all messages until 2nd U8G_COM_MSG_INIT
|
|
|
|
#if ENABLED(PAUSE_LCD_FOR_BUSY_SD)
|
|
if (card.flag.saving || card.flag.logging || TERN0(ESP3D_WIFISUPPORT, sd_busy_lock == true)) return 0;
|
|
#endif
|
|
|
|
if (msgInitCount) {
|
|
if (msg == U8G_COM_MSG_INIT) msgInitCount--;
|
|
if (msgInitCount) return -1;
|
|
}
|
|
|
|
switch (msg) {
|
|
case U8G_COM_MSG_STOP: break;
|
|
|
|
case U8G_COM_MSG_INIT:
|
|
OUT_WRITE(DOGLCD_CS, HIGH);
|
|
OUT_WRITE(DOGLCD_A0, HIGH);
|
|
OUT_WRITE(LCD_RESET_PIN, HIGH);
|
|
u8g_Delay(5);
|
|
spiBegin();
|
|
spiInit(LCD_SPI_SPEED);
|
|
break;
|
|
|
|
case U8G_COM_MSG_ADDRESS: /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
|
|
WRITE(DOGLCD_A0, arg_val ? HIGH : LOW);
|
|
break;
|
|
|
|
case U8G_COM_MSG_CHIP_SELECT: /* arg_val == 0 means HIGH level of U8G_PI_CS */
|
|
WRITE(DOGLCD_CS, arg_val ? LOW : HIGH);
|
|
break;
|
|
|
|
case U8G_COM_MSG_RESET:
|
|
WRITE(LCD_RESET_PIN, arg_val);
|
|
break;
|
|
|
|
case U8G_COM_MSG_WRITE_BYTE:
|
|
spiSend((uint8_t)arg_val);
|
|
break;
|
|
|
|
case U8G_COM_MSG_WRITE_SEQ:
|
|
uint8_t *ptr = (uint8_t*) arg_ptr;
|
|
while (arg_val > 0) {
|
|
spiSend(*ptr++);
|
|
arg_val--;
|
|
}
|
|
break;
|
|
}
|
|
return 1;
|
|
}
|
|
|
|
#endif // EITHER(MKS_MINI_12864, FYSETC_MINI_12864_2_1)
|
|
|
|
#endif // ARDUINO_ARCH_ESP32
|