Firmware2/Marlin/pins_MEGATRONICS_3.h
esenapaj f41c60d4a4 Follow-up the PR #4955, etc
・More ANALOG NUMBERING to Analog Input
・Add comment header to all the section of all the pins files

・Sort sections as follows:
1. Some special definitions (USBCON, LARGE_FLASH, etc)
2. Servos
3. Limit Switches
4. Z Probe
5. Steppers
6. Temperature Sensors
7. Heaters / Fans
8. Misc. Functions
9. LCD / Controller

・Move MAX6675_SS into "Temperature Sensors" section
・Adjust spacing
2016-10-10 14:22:43 +09:00

171 lines
3.9 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* MegaTronics v3.0 pin assignments
*/
#ifndef __AVR_ATmega2560__
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif
#define MEGATRONICS_31
#if ENABLED(MEGATRONICS_31)
#define BOARD_NAME "Megatronics v3.1"
#else
#define BOARD_NAME "Megatronics v3.0"
#endif
#define LARGE_FLASH true
//
// Servos
//
#define SERVO0_PIN 46 // AUX3-6
#define SERVO1_PIN 47 // AUX3-5
#define SERVO2_PIN 48 // AUX3-4
#define SERVO3_PIN 49 // AUX3-3
//
// Limit Switches
//
#define X_MIN_PIN 37
#define X_MAX_PIN 40
#define Y_MIN_PIN 41
#define Y_MAX_PIN 38
#define Z_MIN_PIN 18
#define Z_MAX_PIN 19
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 19
#endif
#define SLED_PIN -1
//
// Steppers
//
#define X_STEP_PIN 58
#define X_DIR_PIN 57
#define X_ENABLE_PIN 59
#define Y_STEP_PIN 5
#define Y_DIR_PIN 17
#define Y_ENABLE_PIN 4
#define Z_STEP_PIN 16
#define Z_DIR_PIN 11
#define Z_ENABLE_PIN 3
#define E0_STEP_PIN 28
#define E0_DIR_PIN 27
#define E0_ENABLE_PIN 29
#define E1_STEP_PIN 25
#define E1_DIR_PIN 24
#define E1_ENABLE_PIN 26
#define E2_STEP_PIN 22
#define E2_DIR_PIN 60
#define E2_ENABLE_PIN 23
//
// Temperature Sensors
//
#if TEMP_SENSOR_0 == -1
#define TEMP_0_PIN 11 // Analog Input
#else
#define TEMP_0_PIN 15 // Analog Input
#endif
#if TEMP_SENSOR_1 == -1
#define TEMP_1_PIN 10 // Analog Input
#else
#define TEMP_1_PIN 13 // Analog Input
#endif
#if TEMP_SENSOR_2 == -1
#define TEMP_2_PIN 9 // Analog Input
#else
#define TEMP_2_PIN 12 // Analog Input
#endif
#if TEMP_SENSOR_BED == -1
#define TEMP_BED_PIN 8 // Analog Input
#else
#define TEMP_BED_PIN 14 // Analog Input
#endif
//
// Heaters / Fans
//
#define HEATER_0_PIN 2
#define HEATER_1_PIN 9
#define HEATER_2_PIN 8
#define HEATER_BED_PIN 10
#define FAN_PIN 6
#define FAN1_PIN 7
//
// Misc. Functions
//
#define SDSS 53
#define LED_PIN 13
#define PS_ON_PIN 12
//
// LCD / Controller
//
#define BEEPER_PIN 61
#define BTN_EN1 44
#define BTN_EN2 45
#define BTN_ENC 33
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define LCD_PINS_RS 56 // CS chip select / SS chip slave select
#define LCD_PINS_ENABLE 51 // SID (MOSI)
#define LCD_PINS_D4 52 // SCK (CLK) clock
#define SD_DETECT_PIN 35
#else
#define LCD_PINS_RS 32
#define LCD_PINS_ENABLE 31
#define LCD_PINS_D4 14
#define LCD_PINS_D5 30
#define LCD_PINS_D6 39
#define LCD_PINS_D7 15
#define SHIFT_CLK 43
#define SHIFT_LD 35
#define SHIFT_OUT 34
#define SHIFT_EN 44
#if ENABLED(MEGATRONICS_31)
#define SD_DETECT_PIN 56
#else
#define SD_DETECT_PIN -1
#endif
#endif