Firmware2/Marlin/Makefile

428 lines
13 KiB
Makefile

# Sprinter Arduino Project Makefile
#
# Makefile Based on:
# Arduino 0011 Makefile
# Arduino adaptation by mellis, eighthave, oli.keller
# Marlin adaption by Daid
#
# This has been tested with Arduino 0022.
#
# This makefile allows you to build sketches from the command line
# without the Arduino environment (or Java).
#
# Detailed instructions for using the makefile:
#
# 1. Modify the line containg "ARDUINO_INSTALL_DIR" to point to the directory that
# contains the Arduino installation (for example, under Mac OS X, this
# might be /Applications/arduino-0012).
#
# 2. Modify the line containing "UPLOAD_PORT" to refer to the filename
# representing the USB or serial connection to your Arduino board
# (e.g. UPLOAD_PORT = /dev/tty.USB0). If the exact name of this file
# changes, you can use * as a wildcard (e.g. UPLOAD_PORT = /dev/tty.usb*).
#
# 3. Set the line containing "MCU" to match your board's processor.
# Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth
# or Diecimila have the atmega168. If you're using a LilyPad Arduino,
# change F_CPU to 8000000. If you are using Gen7 electronics, you
# probably need to use 20000000. Either way, you must regenerate
# the speed lookup table with create_speed_lookuptable.py.
#
# 4. Type "make" and press enter to compile/verify your program.
#
# 5. Type "make upload", reset your Arduino board, and press enter to
# upload your program to the Arduino board.
#
# Note that all settings are set with ?=, this means you can override them
# from the commandline with "make HARDWARE_MOTHERBOARD=71" for example
# This defined the board you are compiling for (see Configuration.h for the options)
HARDWARE_MOTHERBOARD ?= 11
# Arduino source install directory, and version number
ARDUINO_INSTALL_DIR ?= ../../arduino-0022
ARDUINO_VERSION ?= 22
# You can optionally set a path to the avr-gcc tools. Requires a trailing slash. (ex: /usr/local/avr-gcc/bin)
AVR_TOOLS_PATH ?=
#Programmer configuration
UPLOAD_RATE ?= 115200
AVRDUDE_PROGRAMMER ?= arduino
UPLOAD_PORT ?= /dev/arduino
#Directory used to build files in, contains all the build files, from object files to the final hex file.
BUILD_DIR ?= applet
############################################################################
# Below here nothing should be changed...
# Here the Arduino variant is selected by the board type
# HARDWARE_VARIANT = "arduino", "Sanguino", "Gen7", ...
# MCU = "atmega1280", "Mega2560", "atmega2560", "atmega644p", ...
#Gen7
ifeq ($(HARDWARE_MOTHERBOARD),10)
HARDWARE_VARIANT ?= Gen7
MCU ?= atmega644
F_CPU ?= 20000000
else ifeq ($(HARDWARE_MOTHERBOARD),11)
HARDWARE_VARIANT ?= Gen7
MCU ?= atmega644p
F_CPU ?= 20000000
else ifeq ($(HARDWARE_MOTHERBOARD),12)
HARDWARE_VARIANT ?= Gen7
MCU ?= atmega644p
F_CPU ?= 20000000
else ifeq ($(HARDWARE_MOTHERBOARD),13)
HARDWARE_VARIANT ?= Gen7
MCU ?= atmega1284p
F_CPU ?= 20000000
#RAMPS
else ifeq ($(HARDWARE_MOTHERBOARD),3)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),33)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),34)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
#Duemilanove w/ ATMega328P pin assignment
else ifeq ($(HARDWARE_MOTHERBOARD),4)
HARDWARE_VARIANT ?= arduino
HARDWARE_SUB_VARIANT ?= standard
MCU ?= atmega328p
#Gen6
else ifeq ($(HARDWARE_MOTHERBOARD),5)
HARDWARE_VARIANT ?= Gen6
MCU ?= atmega644p
else ifeq ($(HARDWARE_MOTHERBOARD),51)
HARDWARE_VARIANT ?= Gen6
MCU ?= atmega644p
#Sanguinololu
else ifeq ($(HARDWARE_MOTHERBOARD),6)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
else ifeq ($(HARDWARE_MOTHERBOARD),62)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
else ifeq ($(HARDWARE_MOTHERBOARD),63)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
else ifeq ($(HARDWARE_MOTHERBOARD),65)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
else ifeq ($(HARDWARE_MOTHERBOARD),66)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
#Ultimaker
else ifeq ($(HARDWARE_MOTHERBOARD),7)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),71)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega1280
#Teensylu
else ifeq ($(HARDWARE_MOTHERBOARD),8)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
else ifeq ($(HARDWARE_MOTHERBOARD),81)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
else ifeq ($(HARDWARE_MOTHERBOARD),82)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb646
#Gen3+
else ifeq ($(HARDWARE_MOTHERBOARD),9)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
#Megatronics
else ifeq ($(HARDWARE_MOTHERBOARD),70)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
#Alpha OMCA board
else ifeq ($(HARDWARE_MOTHERBOARD),90)
HARDWARE_VARIANT ?= SanguinoA
MCU ?= atmega644
#Final OMCA board
else ifeq ($(HARDWARE_MOTHERBOARD),91)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
#Rambo
else ifeq ($(HARDWARE_MOTHERBOARD),301)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
endif
# Be sure to regenerate speed_lookuptable.h with create_speed_lookuptable.py
# if you are setting this to something other than 16MHz
# Set to 16Mhz if not yet set.
F_CPU ?= 16000000
# Arduino containd the main source code for the Arduino
# Libraries, the "hardware variant" are for boards
# that derives from that, and their source are present in
# the main Marlin source directory
ifeq ($(HARDWARE_VARIANT), arduino)
HARDWARE_DIR = $(ARDUINO_INSTALL_DIR)/hardware
else
ifeq ($(shell [ $(ARDUINO_VERSION) -ge 100 ] && echo true), true)
HARDWARE_DIR = ../ArduinoAddons/Arduino_1.x.x
else
HARDWARE_DIR = ../ArduinoAddons/Arduino_0.xx
endif
endif
HARDWARE_SRC = $(HARDWARE_DIR)/$(HARDWARE_VARIANT)/cores/arduino
TARGET = $(notdir $(CURDIR))
# VPATH tells make to look into these directory for source files,
# there is no need to specify explicit pathnames as long as the
# directory is added here
VPATH = .
VPATH += $(BUILD_DIR)
VPATH += $(HARDWARE_SRC)
ifeq ($(HARDWARE_VARIANT), arduino)
VPATH += $(ARDUINO_INSTALL_DIR)/libraries/LiquidCrystal
VPATH += $(ARDUINO_INSTALL_DIR)/libraries/SPI
else
VPATH += $(HARDWARE_DIR)/libraries/LiquidCrystal
VPATH += $(HARDWARE_DIR)/libraries/SPI
endif
ifeq ($(HARDWARE_VARIANT), arduino)
HARDWARE_SUB_VARIANT ?= mega
VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/variants/$(HARDWARE_SUB_VARIANT)
else
HARDWARE_SUB_VARIANT ?= standard
VPATH += $(HARDWARE_DIR)/$(HARDWARE_VARIANT)/variants/$(HARDWARE_SUB_VARIANT)
endif
SRC = wiring.c \
wiring_analog.c wiring_digital.c \
wiring_pulse.c \
wiring_shift.c WInterrupts.c
CXXSRC = WMath.cpp WString.cpp Print.cpp Marlin_main.cpp \
MarlinSerial.cpp Sd2Card.cpp SdBaseFile.cpp SdFatUtil.cpp \
SdFile.cpp SdVolume.cpp motion_control.cpp planner.cpp \
stepper.cpp temperature.cpp cardreader.cpp ConfigurationStore.cpp \
watchdog.cpp
CXXSRC += LiquidCrystal.cpp ultralcd.cpp SPI.cpp Servo.cpp Tone.cpp
#Check for Arduino 1.0.0 or higher and use the correct sourcefiles for that version
ifeq ($(shell [ $(ARDUINO_VERSION) -ge 100 ] && echo true), true)
CXXSRC += main.cpp
else
SRC += pins_arduino.c main.c
endif
FORMAT = ihex
# Name of this Makefile (used for "make depend").
MAKEFILE = Makefile
# Debugging format.
# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
DEBUG = stabs
OPT = s
DEFINES ?=
# Program settings
CC = $(AVR_TOOLS_PATH)avr-gcc
CXX = $(AVR_TOOLS_PATH)avr-g++
OBJCOPY = $(AVR_TOOLS_PATH)avr-objcopy
OBJDUMP = $(AVR_TOOLS_PATH)avr-objdump
AR = $(AVR_TOOLS_PATH)avr-ar
SIZE = $(AVR_TOOLS_PATH)avr-size
NM = $(AVR_TOOLS_PATH)avr-nm
AVRDUDE = avrdude
REMOVE = rm -f
MV = mv -f
# Place -D or -U options here
CDEFS = -DF_CPU=$(F_CPU) ${addprefix -D , $(DEFINES)}
CXXDEFS = $(CDEFS)
ifeq ($(HARDWARE_VARIANT), Teensy)
CDEFS += -DUSB_SERIAL
SRC += usb.c pins_teensy.c
CXXSRC += usb_api.cpp
endif
# Add all the source directories as include directories too
CINCS = ${addprefix -I ,${VPATH}}
CXXINCS = ${addprefix -I ,${VPATH}}
# Compiler flag to set the C Standard level.
# c89 - "ANSI" C
# gnu89 - c89 plus GCC extensions
# c99 - ISO C99 standard (not yet fully implemented)
# gnu99 - c99 plus GCC extensions
#CSTANDARD = -std=gnu99
CDEBUG = -g$(DEBUG)
CWARN = -Wall -Wstrict-prototypes
CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct \
-fshort-enums -w -ffunction-sections -fdata-sections \
-DARDUINO=$(ARDUINO_VERSION)
ifneq ($(HARDWARE_MOTHERBOARD),)
CTUNING += -DMOTHERBOARD=${HARDWARE_MOTHERBOARD}
endif
#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
CEXTRA = -fno-use-cxa-atexit
CFLAGS := $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CEXTRA) $(CTUNING)
CXXFLAGS := $(CDEFS) $(CINCS) -O$(OPT) -Wall $(CEXTRA) $(CTUNING)
#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs
LDFLAGS = -lm
# Programming support using avrdude. Settings and variables.
AVRDUDE_PORT = $(UPLOAD_PORT)
AVRDUDE_WRITE_FLASH = -U flash:w:$(BUILD_DIR)/$(TARGET).hex:i
AVRDUDE_FLAGS = -D -C $(ARDUINO_INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf \
-p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
-b $(UPLOAD_RATE)
# Define all object files.
OBJ = ${patsubst %.c, $(BUILD_DIR)/%.o, ${SRC}}
OBJ += ${patsubst %.cpp, $(BUILD_DIR)/%.o, ${CXXSRC}}
OBJ += ${patsubst %.S, $(BUILD_DIR)/%.o, ${ASRC}}
# Define all listing files.
LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
# Combine all necessary flags and optional flags.
# Add target processor to flags.
ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
ALL_CXXFLAGS = -mmcu=$(MCU) $(CXXFLAGS)
ALL_ASFLAGS = -mmcu=$(MCU) -x assembler-with-cpp $(ASFLAGS)
# set V=1 (eg, "make V=1") to print the full commands etc.
ifneq ($V,1)
Pecho=@echo
P=@
else
Pecho=@:
P=
endif
# Default target.
all: sizeafter
build: $(BUILD_DIR) elf hex
# Creates the object directory
$(BUILD_DIR):
$P mkdir -p $(BUILD_DIR)
elf: $(BUILD_DIR)/$(TARGET).elf
hex: $(BUILD_DIR)/$(TARGET).hex
eep: $(BUILD_DIR)/$(TARGET).eep
lss: $(BUILD_DIR)/$(TARGET).lss
sym: $(BUILD_DIR)/$(TARGET).sym
# Program the device.
# Do not try to reset an arduino if it's not one
upload: $(BUILD_DIR)/$(TARGET).hex
ifeq (${AVRDUDE_PROGRAMMER}, arduino)
stty hup < $(UPLOAD_PORT); true
endif
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
ifeq (${AVRDUDE_PROGRAMMER}, arduino)
stty -hup < $(UPLOAD_PORT); true
endif
# Display size of file.
HEXSIZE = $(SIZE) --target=$(FORMAT) $(BUILD_DIR)/$(TARGET).hex
ELFSIZE = $(SIZE) --mcu=$(MCU) -C $(BUILD_DIR)/$(TARGET).elf; \
$(SIZE) $(BUILD_DIR)/$(TARGET).elf
sizebefore:
$P if [ -f $(BUILD_DIR)/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_BEFORE); $(HEXSIZE); echo; fi
sizeafter: build
$P if [ -f $(BUILD_DIR)/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); echo; fi
# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
COFFCONVERT=$(OBJCOPY) --debugging \
--change-section-address .data-0x800000 \
--change-section-address .bss-0x800000 \
--change-section-address .noinit-0x800000 \
--change-section-address .eeprom-0x810000
coff: $(BUILD_DIR)/$(TARGET).elf
$(COFFCONVERT) -O coff-avr $(BUILD_DIR)/$(TARGET).elf $(TARGET).cof
extcoff: $(TARGET).elf
$(COFFCONVERT) -O coff-ext-avr $(BUILD_DIR)/$(TARGET).elf $(TARGET).cof
.SUFFIXES: .elf .hex .eep .lss .sym
.PRECIOUS: .o
.elf.hex:
$(Pecho) " COPY $@"
$P $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
.elf.eep:
-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
--change-section-lma .eeprom=0 -O $(FORMAT) $< $@
# Create extended listing file from ELF output file.
.elf.lss:
$(OBJDUMP) -h -S $< > $@
# Create a symbol table from ELF output file.
.elf.sym:
$(NM) -n $< > $@
# Link: create ELF output file from library.
$(BUILD_DIR)/$(TARGET).elf: $(OBJ) Configuration.h
$(Pecho) " CXX $@"
$P $(CC) $(ALL_CXXFLAGS) -Wl,--gc-sections -o $@ -L. $(OBJ) $(LDFLAGS)
$(BUILD_DIR)/%.o: %.c Configuration.h Configuration_adv.h $(MAKEFILE)
$(Pecho) " CC $<"
$P $(CC) -MMD -c $(ALL_CFLAGS) $< -o $@
$(BUILD_DIR)/%.o: $(BUILD_DIR)/%.cpp Configuration.h Configuration_adv.h $(MAKEFILE)
$(Pecho) " CXX $<"
$P $(CXX) -MMD -c $(ALL_CXXFLAGS) $< -o $@
$(BUILD_DIR)/%.o: %.cpp Configuration.h Configuration_adv.h $(MAKEFILE)
$(Pecho) " CXX $<"
$P $(CXX) -MMD -c $(ALL_CXXFLAGS) $< -o $@
# Target: clean project.
clean:
$(Pecho) " RM $(BUILD_DIR)/*"
$P $(REMOVE) $(BUILD_DIR)/$(TARGET).hex $(BUILD_DIR)/$(TARGET).eep $(BUILD_DIR)/$(TARGET).cof $(BUILD_DIR)/$(TARGET).elf \
$(BUILD_DIR)/$(TARGET).map $(BUILD_DIR)/$(TARGET).sym $(BUILD_DIR)/$(TARGET).lss $(BUILD_DIR)/$(TARGET).cpp \
$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
$(Pecho) " RMDIR $(BUILD_DIR)/"
$P rm -rf $(BUILD_DIR)
.PHONY: all build elf hex eep lss sym program coff extcoff clean depend sizebefore sizeafter
# Automaticaly include the dependency files created by gcc
-include ${wildcard $(BUILD_DIR)/*.d}