235 lines
7.4 KiB
C
235 lines
7.4 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
#if NOT_TARGET(__AVR_ATmega644P__, __AVR_ATmega1284P__)
|
|
#error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'"
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "Zonestar ZMIB_V2"
|
|
#define BOARD_WEBSITE_URL "https://www.aliexpress.com/item/32957490744.html"
|
|
|
|
#define IS_ZMIB_V2
|
|
|
|
/**
|
|
* ZMIB pin assignments
|
|
*
|
|
* The ZMIB board needs a bootloader installed before Marlin can be uploaded.
|
|
* If you don't have a chip programmer you can use a spare Arduino plus a few
|
|
* electronic components to write the bootloader.
|
|
*
|
|
* See http://www.instructables.com/id/Burn-Arduino-Bootloader-with-Arduino-MEGA/
|
|
*/
|
|
|
|
/**
|
|
* PIN: 0 Port: B0 HEATER_0_PIN
|
|
* PIN: 1 Port: B1 HEATER_BED_PIN
|
|
* PIN: 2 Port: B2 EXP1_4(BTN_EN2)
|
|
* PIN: 3 Port: B3 V1: SD_DETECT_PIN
|
|
* PIN: 3 Port: B3 V2: EXP1_6
|
|
* PIN: 4 Port: B4 SDSS
|
|
* PIN: 4 Port: B4 V1: EXP1_6
|
|
* PIN: 5 Port: B5 AVR_MOSI_PIN
|
|
* . MOSI_PIN
|
|
* PIN: 6 Port: B6 AVR_MISO_PIN
|
|
* . EXP1_9(MISO_PIN)
|
|
* PIN: 7 Port: B7 AVR_SCK_PIN
|
|
* . EXP1_10(SCK_PIN)
|
|
* PIN: 8 Port: D0 RXD
|
|
* PIN: 9 Port: D1 TXD
|
|
* PIN: 10 Port: D2 EXP1_8
|
|
* PIN: 11 Port: D3 EXP1_7
|
|
* PIN: 12 Port: D4 EXP1_5(BTN_EN1)
|
|
* PIN: 13 Port: D5 Z_MIN_PIN
|
|
* PIN: 14 Port: D6 E1_DIR_PIN
|
|
* PIN: 15 Port: D7 E1_STEP_PIN
|
|
* PIN: 16 Port: C0 Z_DIR_PIN
|
|
* PIN: 17 Port: C1 Z_STEP_PIN
|
|
* PIN: 18 Port: C2 Y_MIN_PIN
|
|
* PIN: 19 Port: C3 Y_DIR_PIN
|
|
* PIN: 20 Port: C4 Y_STEP_PIN
|
|
* PIN: 21 Port: C5 X_MIN_PIN
|
|
* PIN: 22 Port: C6 X_DIR_PIN
|
|
* PIN: 23 Port: C7 X_STEP_PIN
|
|
* PIN: 24 Port: A7 X_ENABLE_PIN
|
|
* Y_ENABLE_PIN
|
|
* Z_ENABLE_PIN
|
|
* E0_ENABLE_PIN
|
|
* E1_ENABLE_PIN
|
|
* PIN: 25 Port: A6 FIL_RUNOUT_PIN
|
|
* PIN: 26 Port: A5 E0_DIR_PIN
|
|
* PIN: 27 Port: A4 E0_STEP_PIN
|
|
* PIN: 28 Port: A3 FAN_PIN
|
|
* PIN: 29 Port: A2 EXP1_3(BTN_ENC)
|
|
* ADC_KEY_PIN
|
|
* PIN: 30 Port: A1 TEMP_0_PIN
|
|
* PIN: 31 Port: A0 TEMP_BED_PIN
|
|
*/
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_MIN_PIN 21
|
|
#define Y_MIN_PIN 18
|
|
|
|
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
|
|
#define Z_MIN_PIN 25
|
|
#else
|
|
#define Z_MIN_PIN 13
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN 23
|
|
#define X_DIR_PIN 22
|
|
#define X_ENABLE_PIN 24
|
|
|
|
#define Y_STEP_PIN 20
|
|
#define Y_DIR_PIN 19
|
|
#define Y_ENABLE_PIN 24
|
|
|
|
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
|
|
#define Z_STEP_PIN 27
|
|
#define Z_DIR_PIN 26
|
|
#else
|
|
#define Z_STEP_PIN 17
|
|
#define Z_DIR_PIN 16
|
|
#endif
|
|
|
|
#define Z_ENABLE_PIN 24
|
|
|
|
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
|
|
#define E0_STEP_PIN 15
|
|
#define E0_DIR_PIN 14
|
|
#else
|
|
#define E0_STEP_PIN 27
|
|
#define E0_DIR_PIN 26
|
|
#endif
|
|
|
|
#define E0_ENABLE_PIN 24
|
|
|
|
#define E1_STEP_PIN 15
|
|
#define E1_DIR_PIN 14
|
|
#define E1_ENABLE_PIN 24
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN 1 // Analog Input
|
|
#define TEMP_BED_PIN 0 // Analog Input
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN 0
|
|
#define HEATER_BED_PIN 1
|
|
#define FAN_PIN 28
|
|
#define FAN1_PIN -1
|
|
|
|
//
|
|
//filament run out sensor
|
|
//
|
|
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
|
|
#define FIL_RUNOUT_PIN 13
|
|
#else
|
|
#define FIL_RUNOUT_PIN 25 // Z-MIN
|
|
#endif
|
|
|
|
//
|
|
// SD card
|
|
//
|
|
#if ENABLED(SDSUPPORT)
|
|
#define SDSS 4
|
|
#endif
|
|
#define SD_DETECT_PIN -1
|
|
|
|
/*===================================================
|
|
* ZMIB Version 1 - EXP1 Connector
|
|
* MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V
|
|
* SCK(D7) RX1(D10) SCS(D4) ENB(D2) GND
|
|
*===================================================
|
|
* ZMIB Version 2 - EXP1 Connector
|
|
* MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V
|
|
* SCK(D7) RX1(D10) SCS(D3) ENB(D2) GND
|
|
*===================================================
|
|
* LCD 128x64
|
|
*==================================================*/
|
|
|
|
#if ENABLED(ZONESTAR_12864LCD)
|
|
//
|
|
// LCD 128x64
|
|
//
|
|
#define LCDSCREEN_NAME "ZONESTAR_12864LCD"
|
|
#define FORCE_SOFT_SPI
|
|
//#define LCD_SDSS 11
|
|
#define LCD_PINS_RS 11 // ST7920_CS_PIN LCD_PIN_RS (PIN4 of LCD module)
|
|
#ifdef IS_ZMIB_V2
|
|
#define LCD_PINS_ENABLE 3 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module)
|
|
#else
|
|
#define LCD_PINS_ENABLE 4 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module)
|
|
#endif
|
|
#define LCD_PINS_D4 10 // ST7920_CLK_PIN LCD_PIN_ENABLE (PIN6 of LCD module)
|
|
|
|
// Alter timing for graphical display
|
|
#define ST7920_DELAY_1 DELAY_2_NOP
|
|
#define ST7920_DELAY_2 DELAY_2_NOP
|
|
#define ST7920_DELAY_3 DELAY_2_NOP
|
|
|
|
#elif EITHER(ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306)
|
|
//
|
|
// OLED 128x64
|
|
//
|
|
#define LCDSCREEN_NAME "ZONESTAR 12864OLED"
|
|
#define FORCE_SOFT_SPI
|
|
#ifdef IS_ZMIB_V2
|
|
#define LCD_PINS_RS 3 // RESET
|
|
#else
|
|
#define LCD_PINS_RS 4 // RESET
|
|
#endif
|
|
#define LCD_PINS_DC 10 // DC
|
|
#define DOGLCD_CS 11 // CS
|
|
#if ENABLED(OLED_HW_IIC)
|
|
#error "Oops! can't choose HW IIC for ZMIB board!!"
|
|
#elif ENABLED(OLED_HW_SPI)
|
|
// HW SPI
|
|
#define DOGLCD_A0 LCD_PINS_DC // A0 = DC
|
|
#else
|
|
// SW SPI
|
|
#define DOGLCD_A0 LCD_PINS_DC // A0 = DC
|
|
#define DOGLCD_MOSI AVR_MOSI_PIN // SDA
|
|
#define DOGLCD_SCK AVR_SCK_PIN // SCK
|
|
#endif
|
|
|
|
#endif
|
|
|
|
//
|
|
// All the above are also RRDSC with rotary encoder
|
|
//
|
|
#if IS_RRD_SC
|
|
#define BTN_EN1 2
|
|
#define BTN_EN2 12
|
|
#define BTN_ENC 29
|
|
#define BEEPER_PIN -1
|
|
#define KILL_PIN -1
|
|
#endif
|