Firmware/Marlin/pins_ANET_10.h

276 lines
11 KiB
C
Raw Normal View History

2017-06-10 07:12:18 +02:00
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Anet V1.0 board pin assignments
*/
/**
* Rev B 16 JUN 2017
*
* 1) no longer uses Sanguino files to define some of the pins
* 2) added pointers to useable Arduino IDE extensions
*
*/
/**
* The standard Arduino IDE extension (board manager) for this board
* is located at https://github.com/SkyNet3D/anet-board.
*
* Installation instructions are on that page.
*
* After copying the files to the appropriate location, restart Arduino and
* you'll see "Anet V1.0" and "Anet V1.0 (Optiboot)" in the boards list.
*
* "Anet V1.0" uses the bootloader that was installed on the board when
* it shipped from the factory.
*
* "Anet V1.0 (Optiboot)" frees up another 3K of FLASH. You'll need to burn
* a new bootloader to the board to be able to automatically download a
* compiled image.
*
*/
/**
* Another usable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
/**
* To burn a new bootloader:
*
* 1. Connect your programmer to the board.
* 2. In the Arduino IDE select the board and then select the programmer.
* 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
* 4. The programmer is no longer needed. Remove it.
*/
/**
* Additional info:
*
* Anet Schematics - https://github.com/ralf-e/ANET-3D-Board-V1.0
* Wiring RRDFG Smart Controller - http://www.thingiverse.com/thing:2103748
* SkyNet3D Anet software development - https://github.com/SkyNet3D/Marlin/
* Anet Users / Skynet SW on Facebook - https://www.facebook.com/skynet3ddevelopment/
*
* Many thanks to Hans Raaf (@oderwat) for developing the Anet-specific software and supporting the Anet community.
2018-02-18 04:43:47 +01:00
*/
2017-06-10 07:12:18 +02:00
#ifndef __AVR_ATmega1284P__
2018-05-19 00:20:54 +02:00
#error "Oops! Make sure you have 'Anet V1.0', 'Anet V1.0 (Optiboot)' or 'Sanguino' selected in the 'Tools -> Boards' menu and ATmega1284P selected in 'Tools -> Processor' menu."
2017-06-10 07:12:18 +02:00
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "Anet"
#endif
//
// Limit Switches
//
#define X_STOP_PIN 18
#define Y_STOP_PIN 19
#define Z_STOP_PIN 20
//
// Steppers
//
#define X_STEP_PIN 15
#define X_DIR_PIN 21
#define X_ENABLE_PIN 14
#define Y_STEP_PIN 22
#define Y_DIR_PIN 23
#define Y_ENABLE_PIN 14
#define Z_STEP_PIN 3
#define Z_DIR_PIN 2
#define Z_ENABLE_PIN 26
#define E0_STEP_PIN 1
#define E0_DIR_PIN 0
#define E0_ENABLE_PIN 14
//
// Temperature Sensors
//
2018-03-28 19:26:44 +02:00
#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder)
#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed)
2017-06-10 07:12:18 +02:00
//
// Heaters / Fans
//
2018-03-28 19:26:44 +02:00
#define HEATER_0_PIN 13 // (extruder)
#define HEATER_BED_PIN 12 // (bed)
2017-06-10 07:12:18 +02:00
#define FAN_PIN 4
//
// Misc. Functions
//
#define SDSS 31
#define LED_PIN -1
/**
* LCD / Controller
*
* Only the following displays are supported:
* ZONESTAR_LCD
2017-06-10 07:12:18 +02:00
* ANET_FULL_GRAPHICS_LCD
* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
*/
2017-06-10 07:12:18 +02:00
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#define LCD_SDSS 28
#if ENABLED(ADC_KEYPAD)
#define SERVO0_PIN 27 // free for BLTouch/3D-Touch
#define LCD_PINS_RS 28
#define LCD_PINS_ENABLE 29
#define LCD_PINS_D4 10
#define LCD_PINS_D5 11
#define LCD_PINS_D6 16
#define LCD_PINS_D7 17
#define BTN_EN1 -1
#define BTN_EN2 -1
#define BTN_ENC -1
#define ADC_KEYPAD_PIN 1
2017-06-10 07:12:18 +02:00
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) || ENABLED(ANET_FULL_GRAPHICS_LCD)
// Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics
// display using an adapter board // https://go.aisler.net/benlye/anet-lcd-adapter/pcb
// See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748
#define SERVO0_PIN 29 // free for BLTouch/3D-Touch
#define BEEPER_PIN 17
#define LCD_PINS_RS 27
#define LCD_PINS_ENABLE 28
#define LCD_PINS_D4 30
#define BTN_EN1 11
#define BTN_EN2 10
#define BTN_ENC 16
2018-03-17 08:37:14 +01:00
#ifndef ST7920_DELAY_1
#define ST7920_DELAY_1 DELAY_NS(0)
2018-03-17 08:37:14 +01:00
#endif
#ifndef ST7920_DELAY_2
#define ST7920_DELAY_2 DELAY_NS(63)
2018-03-17 08:37:14 +01:00
#endif
#ifndef ST7920_DELAY_3
#define ST7920_DELAY_3 DELAY_NS(125)
2018-03-17 08:37:14 +01:00
#endif
2017-09-27 04:19:32 +02:00
#define STD_ENCODER_PULSES_PER_STEP 4
#define STD_ENCODER_STEPS_PER_MENU_ITEM 1
2017-06-10 07:12:18 +02:00
#endif
#else
#define SERVO0_PIN 27
2017-06-10 07:12:18 +02:00
#endif // ULTRA_LCD && NEWPANEL
/**
* ====================================================================
* =============== Alternative RepRapDiscount Wiring ==================
* ====================================================================
*
* An alternative wiring scheme for the RepRapDiscount Full Graphics Display is
* published by oderwat on Thingiverse at https://www.thingiverse.com/thing:2103748.
*
* Using that adapter requires changing the pin definition as follows:
* #define SERVO0_PIN 27 // free for BLTouch/3D-Touch
2017-06-10 07:12:18 +02:00
* #define BEEPER_PIN 28
* #define LCD_PINS_RS 30
* #define LCD_PINS_ENABLE 29
* #define LCD_PINS_D4 17
*
* The BLTouch pin becomes LCD:3
*/
/**
* ====================================================================
* ===================== LCD PINOUTS ==================================
* ====================================================================
*
* Anet V1.0 controller | ZONESTAR_LCD | ANET_FULL_ | RepRapDiscount Full | Thingiverse RepRap wiring
2017-06-10 07:12:18 +02:00
* physical logical alt | | GRAPHICS_LCD | Graphics Display Wiring | http://www.thingiverse
* pin pin functions | | | | .com/thing:2103748
*------------------------------------------------------------------------------------------------------------------------
* ANET-J3.1 8 *** | N/A | J3_TX *** | |
* ANET-J3.2 9 *** | N/A | J3_RX *** | |
* ANET-J3.3 6 MISO | N/A | MISO *** | EXP2.1 MISO | EXP2.1 MISO
* ANET-J3.4 +5V | N/A | +5V | |
* ANET-J3.5 7 SCK | N/A | SCK *** | EXP2.2 SCK | EXP2.2 SCK
* ANET-J3.6 5 MOSI | N/A | MOSI *** | EXP2.6 MOSI | EXP2.6 MOSI
* ANET-J3.7 !RESET | N/A | button | EXP2.8 panel button | EXP2.8 panel button
* ANET-J3.8 GND | N/A | GND | EXP2.9 GND | EXP2.9 GND
* ANET-J3.9 4 Don't use | N/A | N/C | |
* ANET-J3.10 +3.3V | N/A | +3.3V *** | |
* | | | |
* | | | |
* ANET-LCD.1 GND | GND | GND | EXP1.9 GND | EXP1.9 GND
* ANET-LCD.2 +5V | +5V | +5V | EXP1.10 +5V | EXP1.10 +5V
* ANET-LCD.3 27 A4 | N/C * | LCD_PINS_RS | EXP1.4 LCD_PINS_RS | EXP2.4 SDSS or N/C *
* ANET-LCD.4 10 | LCD_PINS_D4 | BTN_EN2 | EXP2.3 BTN_EN2 | EXP2.3 BTN_EN2
* ANET-LCD.5 28 A3 | LCD_PINS_RS | LCD_PINS_ENABLE | EXP1.3 LCD_PINS_ENABLE | EXP1.1 BEEPER_PIN
* ANET-LCD.6 11 | LCD_PINS_D5 | BTN_EN1 | EXP2.5 BTN_EN1 | EXP2.5 BTN_EN1
* ANET-LCD.7 29 A2 | LCD_PINS_ENABLE | N/C * | EXP2.4 SDSS or N/C * | EXP1.3 LCD_PINS_ENABLE
* ANET-LCD.8 16 SCL | LCD_PINS_D6 | BTN_ENC | EXP1.2 BTN_ENC | EXP1.2 BTN_ENC
* ANET-LCD.9 30 A1 | ADC_KEYPAD_PIN ** | LCD_PINS_D4 | EXP1.5 LCD_PINS_D4 | EXP1.4 LCD_PINS_RS
* ANET-LCD.10 17 SDA | LCD_PINS_D7 | BEEPER_PIN | EXP1.1 BEEPER_PIN | EXP1.5 LCD_PINS_D4
*
* N/C * - if not connected to the LCD can be used for BLTouch servo input
* ** - analog pin -WITHOUT a pullup
* *** - only connected to something if the Bluetooth module is populated
*/
/**
* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
* physical pin function
* EXP1.1 BEEPER
* EXP1.2 BTN_ENC
* EXP1.3 LCD_PINS_ENABLE
* EXP1.4 LCD_PINS_RS
* EXP1.5 LCD_PINS_D4
* EXP1.6 LCD_PINS_D5 (not used)
* EXP1.7 LCD_PINS_D6 (not used)
* EXP1.8 LCD_PINS_D7 (not used)
* EXP1.9 GND
* EXP1.10 VCC
*
*
* EXP2.1 MISO
* EXP2.2 SCK
* EXP2.3 BTN_EN2
* EXP2.4 SDSS
* EXP2.5 BTN_EN1
* EXP2.6 MOSI
* EXP2.7 SD_DETECT_PIN
* EXP2.8 button
* EXP2.9 GND
* EXP2.10 NC
*/