Firmware2/Marlin/src/pins/pins_GT2560_V3.h

145 lines
3.3 KiB
C
Raw Normal View History

2018-09-27 21:13:15 +02:00
/**
* Marlin 3D Printer Firmware
2019-02-12 22:06:53 +01:00
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
2018-09-27 21:13:15 +02:00
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* GT2560 V3.0 pin assignment
*/
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
2018-09-27 21:13:15 +02:00
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "GT2560 V3.0"
#endif
2019-01-26 23:16:21 +01:00
//
// Servos
//
#define SERVO0_PIN 11 //13 untested 3Dtouch
2018-09-27 21:13:15 +02:00
//
// Limit Switches
//
#define X_MIN_PIN 24
#define X_MAX_PIN 22
#define Y_MIN_PIN 28
#define Y_MAX_PIN 26
#define Z_MIN_PIN 30
#define Z_MAX_PIN 32
2019-02-05 05:52:41 +01:00
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 32
#endif
2019-01-31 04:10:56 +01:00
//
// Runout Sensor
//
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN 66
#endif
#ifndef FIL_RUNOUT2_PIN
#define FIL_RUNOUT2_PIN 67
#endif
//
// Power Recovery
//
#define POWER_LOSS_PIN 69 // Pin to detect power loss
#define POWER_LOSS_STATE LOW
2018-09-27 21:13:15 +02:00
//
// Steppers
//
#define X_STEP_PIN 37
#define X_DIR_PIN 39
#define X_ENABLE_PIN 35
#define Y_STEP_PIN 31
#define Y_DIR_PIN 33
#define Y_ENABLE_PIN 29
#define Z_STEP_PIN 25
#define Z_DIR_PIN 23
#define Z_ENABLE_PIN 27
#define E0_STEP_PIN 46
#define E0_DIR_PIN 44
#define E0_ENABLE_PIN 12
#define E1_STEP_PIN 49
#define E1_DIR_PIN 47
#define E1_ENABLE_PIN 48
//
// Temperature Sensors
//
#define TEMP_0_PIN 11 // Analog Input
#define TEMP_1_PIN 9 // Analog Input
#define TEMP_2_PIN 1 // Analog Input
#define TEMP_BED_PIN 10 // Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 10
#define HEATER_1_PIN 3
#define HEATER_2_PIN 1
#define HEATER_BED_PIN 4
#define FAN_PIN 9
2019-02-05 05:52:41 +01:00
//#define FAN1_PIN 8
//#define FAN2_PIN 7
2018-09-27 21:13:15 +02:00
//
// Misc. Functions
//
#define SD_DETECT_PIN 38
#define SDSS 53
#define LED_PIN 6
#define PS_ON_PIN 12
2019-02-05 05:52:41 +01:00
#define SUICIDE_PIN 54 // This pin must be enabled at boot to keep power flowing
2018-09-27 21:13:15 +02:00
#ifndef CASE_LIGHT_PIN
2019-02-05 05:52:41 +01:00
#define CASE_LIGHT_PIN 6 // 21
2018-09-27 21:13:15 +02:00
#endif
//
// LCD Controller
//
#define BEEPER_PIN 18
#define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 16
#define LCD_PINS_D5 21
#define LCD_PINS_D6 5
#define LCD_PINS_D7 36
#if ENABLED(NEWPANEL)
#define BTN_EN1 42
#define BTN_EN2 40
#define BTN_ENC 19
#endif