Firmware2/Marlin/src/inc/Conditionals_LCD.h

/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */
#pragma once

/**
 * Conditionals_LCD.h
 * Conditionals that need to be set before Configuration_adv.h or pins.h
 */

// MKS_LCD12864A/B is a variant of MKS_MINI_12864
#if EITHER(MKS_LCD12864A, MKS_LCD12864B)
  #define MKS_MINI_12864
#endif

/**
 * General Flags that may be set below by specific LCDs
 *
 *  DOGLCD                : Run a Graphical LCD through U8GLib (with MarlinUI)
 *  IS_ULTIPANEL          : Define LCD_PINS_D5/6/7 for direct-connected "Ultipanel" LCDs
 *  IS_ULTRA_LCD          : Ultra LCD, not necessarily Ultipanel.
 *  IS_RRD_SC             : Common RRD Smart Controller digital interface pins
 *  IS_RRD_FG_SC          : Common RRD Full Graphical Smart Controller digital interface pins
 *  U8GLIB_ST7920         : Most common DOGM display SPI interface, supporting a "lightweight" display mode.
 *  U8GLIB_SH1106         : SH1106 OLED with I2C interface via U8GLib
 *  IS_U8GLIB_SSD1306     : SSD1306 OLED with I2C interface via U8GLib
 *  U8GLIB_SSD1309        : SSD1309 OLED with I2C interface via U8GLib
 *  U8GLIB_ST7565_64128N  : ST7565 128x64 LCD with SPI interface via U8GLib
 *  U8GLIB_LM6059_AF      : LM6059 with Hardware SPI via U8GLib
 */
#if EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)

  #define MINIPANEL

#elif ENABLED(YHCB2004)

  #define IS_ULTIPANEL 1

#elif ENABLED(CARTESIO_UI)

  #define DOGLCD
  #define IS_ULTIPANEL 1

#elif EITHER(DWIN_MARLINUI_PORTRAIT, DWIN_MARLINUI_LANDSCAPE)

  #define IS_DWIN_MARLINUI 1
  #define IS_ULTIPANEL 1

#elif ENABLED(ZONESTAR_LCD)

  #define HAS_ADC_BUTTONS 1
  #define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
  #define ADC_KEY_NUM 8
  #define IS_ULTIPANEL 1

  // This helps to implement HAS_ADC_BUTTONS menus
  #define REVERSE_MENU_DIRECTION
  #define ENCODER_PULSES_PER_STEP 1
  #define ENCODER_STEPS_PER_MENU_ITEM 1
  #define ENCODER_FEEDRATE_DEADZONE 2

#elif ENABLED(ZONESTAR_12864LCD)
  #define DOGLCD
  #define IS_RRD_SC 1
  #define U8GLIB_ST7920

#elif ENABLED(ZONESTAR_12864OLED)
  #define IS_RRD_SC 1
  #define U8GLIB_SH1106

#elif ENABLED(ZONESTAR_12864OLED_SSD1306)
  #define IS_RRD_SC 1
  #define IS_U8GLIB_SSD1306

#elif ENABLED(RADDS_DISPLAY)
  #define IS_ULTIPANEL 1
  #define ENCODER_PULSES_PER_STEP 2

#elif ANY(miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864)

  #define DOGLCD
  #define IS_ULTIPANEL 1

  #if ENABLED(miniVIKI)
    #define U8GLIB_ST7565_64128N
  #elif ENABLED(VIKI2)
    #define U8GLIB_ST7565_64128N
  #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
    #define U8GLIB_LM6059_AF
  #elif ENABLED(AZSMZ_12864)
    #define U8GLIB_ST7565_64128N
  #endif

#elif ENABLED(OLED_PANEL_TINYBOY2)

  #define IS_U8GLIB_SSD1306
  #define IS_ULTIPANEL 1

#elif ENABLED(RA_CONTROL_PANEL)

  #define LCD_I2C_TYPE_PCA8574
  #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
  #define IS_ULTIPANEL 1

#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)

  #define DOGLCD
  #define U8GLIB_ST7920
  #define IS_ULTIPANEL 1

#elif ENABLED(MKS_12864OLED)

  #define IS_RRD_SC 1
  #define U8GLIB_SH1106

#elif ENABLED(MKS_12864OLED_SSD1306)

  #define IS_RRD_SC 1
  #define IS_U8GLIB_SSD1306

#elif ENABLED(FYSETC_242_OLED_12864)

  #define IS_RRD_SC 1
  #define U8GLIB_SH1106

  #define LED_CONTROL_MENU
  #define NEOPIXEL_LED
  #undef NEOPIXEL_TYPE
  #define NEOPIXEL_TYPE       NEO_RGB
  #if NEOPIXEL_PIXELS < 3
    #undef NEOPIXELS_PIXELS
    #define NEOPIXEL_PIXELS     3
  #endif
  #ifndef NEOPIXEL_BRIGHTNESS
    #define NEOPIXEL_BRIGHTNESS 127
  #endif

  #if ENABLED(PSU_CONTROL)
    #define LED_BACKLIGHT_TIMEOUT 10000
  #endif

#elif ANY(FYSETC_MINI_12864_X_X, FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1, FYSETC_GENERIC_12864_1_1)

  #define FYSETC_MINI_12864
  #define DOGLCD
  #define IS_ULTIPANEL 1
  #define LED_COLORS_REDUCE_GREEN
  #if ENABLED(PSU_CONTROL) && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1)
    #define LED_BACKLIGHT_TIMEOUT 10000
  #endif

  // Require LED backlighting enabled
  #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
    #define RGB_LED
  #elif ENABLED(FYSETC_MINI_12864_2_1)
    #define LED_CONTROL_MENU
    #define NEOPIXEL_LED
    #undef NEOPIXEL_TYPE
    #define NEOPIXEL_TYPE       NEO_RGB
    #if NEOPIXEL_PIXELS < 3
      #undef NEOPIXELS_PIXELS
      #define NEOPIXEL_PIXELS     3
    #endif
    #ifndef NEOPIXEL_BRIGHTNESS
      #define NEOPIXEL_BRIGHTNESS 127
    #endif
    //#define NEOPIXEL_STARTUP_TEST
  #endif

#elif ENABLED(ULTI_CONTROLLER)

  #define IS_ULTIPANEL 1
  #define U8GLIB_SSD1309
  #define LCD_RESET_PIN LCD_PINS_D6 //  This controller need a reset pin
  #define ENCODER_PULSES_PER_STEP 2
  #define ENCODER_STEPS_PER_MENU_ITEM 2

#elif ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602)

  #define IS_RRD_SC 1
  #define LCD_WIDTH 16
  #define LCD_HEIGHT 2

#elif EITHER(TFTGLCD_PANEL_SPI, TFTGLCD_PANEL_I2C)

  #define IS_TFTGLCD_PANEL 1
  #define IS_ULTIPANEL 1                    // Note that IS_ULTIPANEL leads to HAS_WIRED_LCD

  #if ENABLED(SDSUPPORT) && DISABLED(LCD_PROGRESS_BAR)
    #define LCD_PROGRESS_BAR
  #endif
  #if ENABLED(TFTGLCD_PANEL_I2C)
    #define LCD_I2C_ADDRESS           0x27  // Must be equal to panel's I2C slave addres
  #endif
  #define LCD_USE_I2C_BUZZER                // Enable buzzer on LCD, used for both I2C and SPI buses (LiquidTWI2 not required)
  #define STD_ENCODER_PULSES_PER_STEP 2
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 1
  #define LCD_WIDTH                   20    // 20 or 24 chars in line
  #define LCD_HEIGHT                  10    // Character lines
  #define LCD_CONTRAST_MIN            127
  #define LCD_CONTRAST_MAX            255
  #define DEFAULT_LCD_CONTRAST        250
  #define CONVERT_TO_EXT_ASCII        // Use extended 128-255 symbols from ASCII table.
                                      // At this time present conversion only for cyrillic - bg, ru and uk languages.
                                      // First 7 ASCII symbols in panel font must be replaced with Marlin's special symbols.

#elif ENABLED(CR10_STOCKDISPLAY)

  #define IS_RRD_FG_SC 1
  #define BOARD_ST7920_DELAY_1 DELAY_NS(125)
  #define BOARD_ST7920_DELAY_2 DELAY_NS(125)
  #define BOARD_ST7920_DELAY_3 DELAY_NS(125)

#elif ANY(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER, ANET_FULL_GRAPHICS_LCD, ANET_FULL_GRAPHICS_LCD_ALT_WIRING, BQ_LCD_SMART_CONTROLLER, K3D_FULL_GRAPHIC_SMART_CONTROLLER)

  #define IS_RRD_FG_SC 1

#elif ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)

  #define IS_RRD_SC 1   // RepRapDiscount LCD or Graphical LCD with rotary click encoder

#elif ENABLED(K3D_242_OLED_CONTROLLER)

  #define IS_RRD_SC 1
  #define U8GLIB_SSD1309

#endif

// ST7920-based graphical displays
#if ANY(IS_RRD_FG_SC, LCD_FOR_MELZI, SILVER_GATE_GLCD_CONTROLLER)
  #define DOGLCD
  #define U8GLIB_ST7920
  #define IS_RRD_SC 1
#endif

// ST7565 / 64128N graphical displays
#if EITHER(MAKRPANEL, MINIPANEL)
  #define IS_ULTIPANEL 1
  #define DOGLCD
  #if ENABLED(MAKRPANEL)
    #define U8GLIB_ST7565_64128N
  #endif
#endif

#if ENABLED(IS_U8GLIB_SSD1306)
  #define U8GLIB_SSD1306
#endif

#if ENABLED(OVERLORD_OLED)
  #define IS_ULTIPANEL 1
  #define U8GLIB_SH1106
  /**
   * PCA9632 for buzzer and LEDs via i2c
   * No auto-inc, red and green leds switched, buzzer
   */
  #define PCA9632
  #define PCA9632_NO_AUTO_INC
  #define PCA9632_GRN         0x00
  #define PCA9632_RED         0x02
  #define PCA9632_BUZZER
  #define PCA9632_BUZZER_DATA { 0x09, 0x02 }

  #define ENCODER_PULSES_PER_STEP     1 // Overlord uses buttons
  #define ENCODER_STEPS_PER_MENU_ITEM 1
#endif

// 128x64 I2C OLED LCDs - SSD1306/SSD1309/SH1106
#if ANY(U8GLIB_SSD1306, U8GLIB_SSD1309, U8GLIB_SH1106)
  #define HAS_U8GLIB_I2C_OLED 1
  #define IS_ULTRA_LCD 1
  #define DOGLCD
#endif

/**
 * SPI Ultipanels
 */

// Basic Ultipanel-like displays
#if ANY(ULTIMAKERCONTROLLER, IS_RRD_SC, G3D_PANEL, RIGIDBOT_PANEL, PANEL_ONE, U8GLIB_SH1106)
  #define IS_ULTIPANEL 1
#endif

// Einstart OLED has Cardinal nav via pins defined in pins_EINSTART-S.h
#if ENABLED(U8GLIB_SH1106_EINSTART)
  #define DOGLCD
  #define IS_ULTIPANEL 1
#endif

// TFT Compatibility
#if ANY(FSMC_GRAPHICAL_TFT, SPI_GRAPHICAL_TFT, TFT_320x240, TFT_480x320, TFT_320x240_SPI, TFT_480x320_SPI, TFT_LVGL_UI_FSMC, TFT_LVGL_UI_SPI)
  #define IS_LEGACY_TFT 1
  #define TFT_GENERIC
  #warning "Don't forget to update your TFT settings in Configuration.h."
#endif

#if ANY(FSMC_GRAPHICAL_TFT, TFT_320x240, TFT_480x320, TFT_LVGL_UI_FSMC)
  #define TFT_INTERFACE_FSMC
#elif ANY(SPI_GRAPHICAL_TFT, TFT_320x240_SPI, TFT_480x320_SPI, TFT_LVGL_UI_SPI)
  #define TFT_INTERFACE_SPI
#endif

#if EITHER(FSMC_GRAPHICAL_TFT, SPI_GRAPHICAL_TFT)
  #define TFT_CLASSIC_UI
#elif ANY(TFT_320x240, TFT_480x320, TFT_320x240_SPI, TFT_480x320_SPI)
  #define TFT_COLOR_UI
#elif EITHER(TFT_LVGL_UI_FSMC, TFT_LVGL_UI_SPI)
  #define TFT_LVGL_UI
#endif

// FSMC/SPI TFT Panels (LVGL)
#if ENABLED(TFT_LVGL_UI)
  #define HAS_TFT_LVGL_UI 1
  #define SERIAL_RUNTIME_HOOK 1
#endif

// FSMC/SPI TFT Panels
#if ENABLED(TFT_CLASSIC_UI)
  #define TFT_SCALED_DOGLCD 1
#endif

#if TFT_SCALED_DOGLCD
  #define DOGLCD
  #define IS_ULTIPANEL 1
  #define DELAYED_BACKLIGHT_INIT
#elif HAS_TFT_LVGL_UI
  #define DELAYED_BACKLIGHT_INIT
#endif

// Color UI
#if ENABLED(TFT_COLOR_UI)
  #define HAS_GRAPHICAL_TFT 1
  #define IS_ULTIPANEL 1
#endif

/**
 * I2C Panels
 */

#if EITHER(LCD_SAINSMART_I2C_1602, LCD_SAINSMART_I2C_2004)

  #define LCD_I2C_TYPE_PCF8575
  #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander

  #if ENABLED(LCD_SAINSMART_I2C_2004)
    #define LCD_WIDTH 20
    #define LCD_HEIGHT 4
  #endif

#elif ENABLED(LCD_I2C_PANELOLU2)

  // PANELOLU2 LCD with status LEDs, separate encoder and click inputs

  #define LCD_I2C_TYPE_MCP23017
  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
  #define LCD_USE_I2C_BUZZER   // Enable buzzer on LCD (optional)
  #define IS_ULTIPANEL 1

#elif ENABLED(LCD_I2C_VIKI)

  /**
   * Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
   *
   * This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
   * Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
   * Note: The pause/stop/resume LCD button pin should be connected to the Arduino
   *       BTN_ENC pin (or set BTN_ENC to -1 if not used)
   */
  #define LCD_I2C_TYPE_MCP23017
  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
  #define LCD_USE_I2C_BUZZER   // Enable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
  #define IS_ULTIPANEL 1

  #define ENCODER_FEEDRATE_DEADZONE 4

  #define STD_ENCODER_PULSES_PER_STEP 1
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 2

#elif ENABLED(G3D_PANEL)

  #define STD_ENCODER_PULSES_PER_STEP 2
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 1

#elif ANY(IS_RRD_SC, miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864, OLED_PANEL_TINYBOY2, BQ_LCD_SMART_CONTROLLER, LCD_I2C_PANELOLU2)

  #define STD_ENCODER_PULSES_PER_STEP 4
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 1

#endif

#if EITHER(LCD_I2C_TYPE_MCP23017, LCD_I2C_TYPE_MCP23008) && DISABLED(NO_LCD_DETECT)
  #define DETECT_I2C_LCD_DEVICE 1
#endif

#ifndef STD_ENCODER_PULSES_PER_STEP
  #if ENABLED(TOUCH_SCREEN)
    #define STD_ENCODER_PULSES_PER_STEP 2
  #else
    #define STD_ENCODER_PULSES_PER_STEP 5
  #endif
#endif
#ifndef STD_ENCODER_STEPS_PER_MENU_ITEM
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 1
#endif
#ifndef ENCODER_PULSES_PER_STEP
  #define ENCODER_PULSES_PER_STEP STD_ENCODER_PULSES_PER_STEP
#endif
#ifndef ENCODER_STEPS_PER_MENU_ITEM
  #define ENCODER_STEPS_PER_MENU_ITEM STD_ENCODER_STEPS_PER_MENU_ITEM
#endif
#ifndef ENCODER_FEEDRATE_DEADZONE
  #define ENCODER_FEEDRATE_DEADZONE 6
#endif

// Shift register panels
// ---------------------
// 2 wire Non-latching LCD SR from:
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
#if ENABLED(FF_INTERFACEBOARD)
  #define SR_LCD_3W_NL    // Non latching 3 wire shift register
  #define IS_ULTIPANEL 1
#elif ENABLED(SAV_3DLCD)
  #define SR_LCD_2W_NL    // Non latching 2 wire shift register
  #define IS_ULTIPANEL 1
#elif ENABLED(ULTIPANEL)
  #define IS_ULTIPANEL 1
#endif

#if EITHER(IS_ULTIPANEL, ULTRA_LCD)
  #define IS_ULTRA_LCD 1
#endif

#if EITHER(IS_ULTIPANEL, REPRAPWORLD_KEYPAD)
  #define IS_NEWPANEL 1
#endif

#if EITHER(ZONESTAR_LCD, REPRAPWORLD_KEYPAD)
  #define IS_RRW_KEYPAD 1
  #ifndef REPRAPWORLD_KEYPAD_MOVE_STEP
    #define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  #endif
#endif

// Aliases for LCD features
#if ANY(DGUS_LCD_UI_ORIGIN, DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_HIPRECY,DGUS_LCD_UI_MKS)
  #define HAS_DGUS_LCD 1
#endif

// Extensible UI serial touch screens. (See src/lcd/extui)
#if ANY(HAS_DGUS_LCD, MALYAN_LCD, TOUCH_UI_FTDI_EVE, ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON, NEXTION_TFT)
  #define IS_EXTUI 1
  #define EXTENSIBLE_UI
#endif

// Aliases for LCD features
#if EITHER(IS_ULTRA_LCD, EXTENSIBLE_UI)
  #define HAS_DISPLAY 1
#endif

#if IS_ULTRA_LCD
  #define HAS_WIRED_LCD 1
  #if ENABLED(DOGLCD)
    #define HAS_MARLINUI_U8GLIB 1
  #elif IS_TFTGLCD_PANEL
    // Neither DOGM nor HD44780. Fully customized interface.
  #elif DISABLED(HAS_GRAPHICAL_TFT)
    #define HAS_MARLINUI_HD44780 1
  #endif
#endif

#if ANY(HAS_DISPLAY, DWIN_CREALITY_LCD, GLOBAL_STATUS_MESSAGE)
  #define HAS_STATUS_MESSAGE 1
#endif

#if IS_ULTIPANEL && DISABLED(NO_LCD_MENUS)
  #define HAS_LCD_MENU 1
#endif

#if HAS_MARLINUI_U8GLIB
  #ifndef LCD_PIXEL_WIDTH
    #define LCD_PIXEL_WIDTH 128
  #endif
  #ifndef LCD_PIXEL_HEIGHT
    #define LCD_PIXEL_HEIGHT 64
  #endif
#endif

/**
 *  Multi-Material-Unit supported models
 */
#define PRUSA_MMU1             1
#define PRUSA_MMU2             2
#define PRUSA_MMU2S            3
#define EXTENDABLE_EMU_MMU2   12
#define EXTENDABLE_EMU_MMU2S  13

#ifdef MMU_MODEL
  #define HAS_MMU 1
  #if MMU_MODEL == PRUSA_MMU1
    #define HAS_PRUSA_MMU1 1
  #elif MMU_MODEL % 10 == PRUSA_MMU2
    #define HAS_PRUSA_MMU2 1
  #elif MMU_MODEL % 10 == PRUSA_MMU2S
    #define HAS_PRUSA_MMU2 1
    #define HAS_PRUSA_MMU2S 1
  #endif
  #if MMU_MODEL >= EXTENDABLE_EMU_MMU2
    #define HAS_EXTENDABLE_MMU 1
  #endif
#endif

#undef PRUSA_MMU1
#undef PRUSA_MMU2
#undef PRUSA_MMU2S
#undef EXTENDABLE_EMU_MMU2
#undef EXTENDABLE_EMU_MMU2S

/**
 * Extruders have some combination of stepper motors and hotends
 * so we separate these concepts into the defines:
 *
 *  EXTRUDERS    - Number of Selectable Tools
 *  HOTENDS      - Number of hotends, whether connected or separate
 *  E_STEPPERS   - Number of actual E stepper motors
 *  E_MANUAL     - Number of E steppers for LCD move options
 */
#if EXTRUDERS
  #define HAS_EXTRUDERS 1
  #if EXTRUDERS > 1
    #define HAS_MULTI_EXTRUDER 1
  #endif
  #define E_AXIS_N(E) AxisEnum(E_AXIS + E_INDEX_N(E))
#else
  #undef EXTRUDERS
  #define EXTRUDERS 0
  #undef SINGLENOZZLE
  #undef SWITCHING_EXTRUDER
  #undef SWITCHING_NOZZLE
  #undef MIXING_EXTRUDER
  #undef HOTEND_IDLE_TIMEOUT
  #undef DISABLE_E
#endif

#if ENABLED(SWITCHING_EXTRUDER)   // One stepper for every two EXTRUDERS
  #if EXTRUDERS > 4
    #define E_STEPPERS    3
  #elif EXTRUDERS > 2
    #define E_STEPPERS    2
  #else
    #define E_STEPPERS    1
  #endif
  #if DISABLED(SWITCHING_NOZZLE)
    #define HOTENDS       E_STEPPERS
  #endif
#elif ENABLED(MIXING_EXTRUDER)
  #define E_STEPPERS      MIXING_STEPPERS
  #define E_MANUAL        1
  #if MIXING_STEPPERS == 2
    #define HAS_DUAL_MIXING 1
  #endif
#elif ENABLED(SWITCHING_TOOLHEAD)
  #define E_STEPPERS      EXTRUDERS
  #define E_MANUAL        EXTRUDERS
#elif HAS_PRUSA_MMU2
  #define E_STEPPERS 1
#endif

// No inactive extruders with SWITCHING_NOZZLE or Průša MMU1
#if ENABLED(SWITCHING_NOZZLE) || HAS_PRUSA_MMU1
  #undef DISABLE_INACTIVE_EXTRUDER
#endif

// Průša MMU1, MMU(S) 2.0 and EXTENDABLE_EMU_MMU2(S) force SINGLENOZZLE
#if HAS_MMU
  #define SINGLENOZZLE
#endif

#if EITHER(SINGLENOZZLE, MIXING_EXTRUDER)         // One hotend, one thermistor, no XY offset
  #undef HOTENDS
  #define HOTENDS       1
  #undef HOTEND_OFFSET_X
  #undef HOTEND_OFFSET_Y
#endif

#ifndef HOTENDS
  #define HOTENDS EXTRUDERS
#endif
#ifndef E_STEPPERS
  #define E_STEPPERS EXTRUDERS
#endif
#ifndef E_MANUAL
  #define E_MANUAL EXTRUDERS
#endif

/**
 * Number of Linear Axes (e.g., XYZ)
 * All the logical axes except for the tool (E) axis
 */
#ifndef LINEAR_AXES
  #define LINEAR_AXES XYZ
#endif
#if LINEAR_AXES >= XY
  #define HAS_Y_AXIS 1
  #if LINEAR_AXES >= XYZ
    #define HAS_Z_AXIS 1
  #endif
#endif

/**
 * Number of Logical Axes (e.g., XYZE)
 * All the logical axes that can be commanded directly by G-code.
 * Delta maps stepper-specific values to ABC steppers.
 */
#if HAS_EXTRUDERS
  #define LOGICAL_AXES INCREMENT(LINEAR_AXES)
#else
  #define LOGICAL_AXES LINEAR_AXES
#endif

/**
 * DISTINCT_E_FACTORS is set to give extruders (some) individual settings.
 *
 * DISTINCT_AXES is the number of distinct addressable axes (not steppers).
 *  Includes all linear axes plus all distinguished extruders.
 *  The default behavior is to treat all extruders as a single E axis
 *  with shared motion and temperature settings.
 *
 * DISTINCT_E is the number of distinguished extruders. By default this
 *  well be 1 which indicates all extruders share the same settings.
 *
 * E_INDEX_N(E) should be used to get the E index of any item that might be
 *  distinguished.
 */
#if ENABLED(DISTINCT_E_FACTORS) && E_STEPPERS > 1
  #define DISTINCT_AXES (LINEAR_AXES + E_STEPPERS)
  #define DISTINCT_E E_STEPPERS
  #define E_INDEX_N(E) (E)
#else
  #undef DISTINCT_E_FACTORS
  #define DISTINCT_AXES LOGICAL_AXES
  #define DISTINCT_E 1
  #define E_INDEX_N(E) 0
#endif

#if HOTENDS
  #define HAS_HOTEND 1
  #ifndef HOTEND_OVERSHOOT
    #define HOTEND_OVERSHOOT 15
  #endif
  #if HOTENDS > 1
    #define HAS_MULTI_HOTEND 1
    #define HAS_HOTEND_OFFSET 1
  #endif
#else
  #undef PID_PARAMS_PER_HOTEND
#endif

// Helper macros for extruder and hotend arrays
#define HOTEND_LOOP() for (int8_t e = 0; e < HOTENDS; e++)
#define ARRAY_BY_EXTRUDERS(V...) ARRAY_N(EXTRUDERS, V)
#define ARRAY_BY_EXTRUDERS1(v1) ARRAY_N_1(EXTRUDERS, v1)
#define ARRAY_BY_HOTENDS(V...) ARRAY_N(HOTENDS, V)
#define ARRAY_BY_HOTENDS1(v1) ARRAY_N_1(HOTENDS, v1)

/**
 * Default hotend offsets, if not defined
 */
#if HAS_HOTEND_OFFSET
  #ifndef HOTEND_OFFSET_X
    #define HOTEND_OFFSET_X { 0 } // X offsets for each extruder
  #endif
  #ifndef HOTEND_OFFSET_Y
    #define HOTEND_OFFSET_Y { 0 } // Y offsets for each extruder
  #endif
  #ifndef HOTEND_OFFSET_Z
    #define HOTEND_OFFSET_Z { 0 } // Z offsets for each extruder
  #endif
#endif

/**
 * Disable unused SINGLENOZZLE sub-options
 */
#if DISABLED(SINGLENOZZLE)
  #undef SINGLENOZZLE_STANDBY_TEMP
#endif
#if !BOTH(HAS_FAN, SINGLENOZZLE)
  #undef SINGLENOZZLE_STANDBY_FAN
#endif

// Switching extruder has its own servo?
#if ENABLED(SWITCHING_EXTRUDER) && (DISABLED(SWITCHING_NOZZLE) || SWITCHING_EXTRUDER_SERVO_NR != SWITCHING_NOZZLE_SERVO_NR)
  #define DO_SWITCH_EXTRUDER 1
#endif

/**
 * The BLTouch Probe emulates a servo probe
 * and uses "special" angles for its state.
 */
#if ENABLED(BLTOUCH)
  #ifndef Z_PROBE_SERVO_NR
    #define Z_PROBE_SERVO_NR 0
  #endif
  #ifdef DEACTIVATE_SERVOS_AFTER_MOVE
    #warning "BLTOUCH requires DEACTIVATE_SERVOS_AFTER_MOVE to be to disabled. Undefining DEACTIVATE_SERVOS_AFTER_MOVE. Please update your Configuration.h file."
    #undef DEACTIVATE_SERVOS_AFTER_MOVE
  #endif

  // Always disable probe pin inverting for BLTouch
  #if Z_MIN_PROBE_ENDSTOP_INVERTING
    #warning "BLTOUCH requires Z_MIN_PROBE_ENDSTOP_INVERTING set to false. Resetting Z_MIN_PROBE_ENDSTOP_INVERTING to false. Please update your Configuration.h file."
    #undef Z_MIN_PROBE_ENDSTOP_INVERTING
    #define Z_MIN_PROBE_ENDSTOP_INVERTING false
  #endif

  #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
    #if Z_MIN_ENDSTOP_INVERTING
      #warning "BLTOUCH requires Z_MIN_ENDSTOP_INVERTING set to false. Resetting Z_MIN_ENDSTOP_INVERTING to false. Please update your Configuration.h file."
      #undef Z_MIN_ENDSTOP_INVERTING
      #define Z_MIN_ENDSTOP_INVERTING false
    #endif
  #endif
#endif

/**
 * Set a flag for a servo probe (or BLTouch)
 */
#ifdef Z_PROBE_SERVO_NR
  #define HAS_Z_SERVO_PROBE 1
#endif
#if ANY(HAS_Z_SERVO_PROBE, SWITCHING_EXTRUDER, SWITCHING_NOZZLE)
  #define HAS_SERVO_ANGLES 1
#endif
#if !HAS_SERVO_ANGLES
  #undef EDITABLE_SERVO_ANGLES
#endif

/**
 * Set flags for enabled probes
 */
#if ANY(HAS_Z_SERVO_PROBE, FIX_MOUNTED_PROBE, NOZZLE_AS_PROBE, TOUCH_MI_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, SOLENOID_PROBE, SENSORLESS_PROBING, RACK_AND_PINION_PROBE)
  #define HAS_BED_PROBE 1
#endif

/**
 * Fill in undefined Filament Sensor options
 */
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
  #if NUM_RUNOUT_SENSORS >= 1
    #ifndef FIL_RUNOUT1_STATE
      #define FIL_RUNOUT1_STATE FIL_RUNOUT_STATE
    #endif
    #ifndef FIL_RUNOUT1_PULLUP
      #define FIL_RUNOUT1_PULLUP FIL_RUNOUT_PULLUP
    #endif
    #ifndef FIL_RUNOUT1_PULLDOWN
      #define FIL_RUNOUT1_PULLDOWN FIL_RUNOUT_PULLDOWN
    #endif
  #endif
  #if NUM_RUNOUT_SENSORS >= 2
    #ifndef FIL_RUNOUT2_STATE
      #define FIL_RUNOUT2_STATE FIL_RUNOUT_STATE
    #endif
    #ifndef FIL_RUNOUT2_PULLUP
      #define FIL_RUNOUT2_PULLUP FIL_RUNOUT_PULLUP
    #endif
    #ifndef FIL_RUNOUT2_PULLDOWN
      #define FIL_RUNOUT2_PULLDOWN FIL_RUNOUT_PULLDOWN
    #endif
  #endif
  #if NUM_RUNOUT_SENSORS >= 3
    #ifndef FIL_RUNOUT3_STATE
      #define FIL_RUNOUT3_STATE FIL_RUNOUT_STATE
    #endif
    #ifndef FIL_RUNOUT3_PULLUP
      #define FIL_RUNOUT3_PULLUP FIL_RUNOUT_PULLUP
    #endif
    #ifndef FIL_RUNOUT3_PULLDOWN
      #define FIL_RUNOUT3_PULLDOWN FIL_RUNOUT_PULLDOWN
    #endif
  #endif
  #if NUM_RUNOUT_SENSORS >= 4
    #ifndef FIL_RUNOUT4_STATE
      #define FIL_RUNOUT4_STATE FIL_RUNOUT_STATE
    #endif
    #ifndef FIL_RUNOUT4_PULLUP
      #define FIL_RUNOUT4_PULLUP FIL_RUNOUT_PULLUP
    #endif
    #ifndef FIL_RUNOUT4_PULLDOWN
      #define FIL_RUNOUT4_PULLDOWN FIL_RUNOUT_PULLDOWN
    #endif
  #endif
  #if NUM_RUNOUT_SENSORS >= 5
    #ifndef FIL_RUNOUT5_STATE
      #define FIL_RUNOUT5_STATE FIL_RUNOUT_STATE
    #endif
    #ifndef FIL_RUNOUT5_PULLUP
      #define FIL_RUNOUT5_PULLUP FIL_RUNOUT_PULLUP
    #endif
    #ifndef FIL_RUNOUT5_PULLDOWN
      #define FIL_RUNOUT5_PULLDOWN FIL_RUNOUT_PULLDOWN
    #endif
  #endif
  #if NUM_RUNOUT_SENSORS >= 6
    #ifndef FIL_RUNOUT6_STATE
      #define FIL_RUNOUT6_STATE FIL_RUNOUT_STATE
    #endif
    #ifndef FIL_RUNOUT6_PULLUP
      #define FIL_RUNOUT6_PULLUP FIL_RUNOUT_PULLUP
    #endif
    #ifndef FIL_RUNOUT6_PULLDOWN
      #define FIL_RUNOUT6_PULLDOWN FIL_RUNOUT_PULLDOWN
    #endif
  #endif
  #if NUM_RUNOUT_SENSORS >= 7
    #ifndef FIL_RUNOUT7_STATE
      #define FIL_RUNOUT7_STATE FIL_RUNOUT_STATE
    #endif
    #ifndef FIL_RUNOUT7_PULLUP
      #define FIL_RUNOUT7_PULLUP FIL_RUNOUT_PULLUP
    #endif
    #ifndef FIL_RUNOUT7_PULLDOWN
      #define FIL_RUNOUT7_PULLDOWN FIL_RUNOUT_PULLDOWN
    #endif
  #endif
  #if NUM_RUNOUT_SENSORS >= 8
    #ifndef FIL_RUNOUT8_STATE
      #define FIL_RUNOUT8_STATE FIL_RUNOUT_STATE
    #endif
    #ifndef FIL_RUNOUT8_PULLUP
      #define FIL_RUNOUT8_PULLUP FIL_RUNOUT_PULLUP
    #endif
    #ifndef FIL_RUNOUT8_PULLDOWN
      #define FIL_RUNOUT8_PULLDOWN FIL_RUNOUT_PULLDOWN
    #endif
  #endif
#endif // FILAMENT_RUNOUT_SENSOR

// Homing to Min or Max
#if X_HOME_DIR > 0
  #define X_HOME_TO_MAX 1
#elif X_HOME_DIR < 0
  #define X_HOME_TO_MIN 1
#endif
#if Y_HOME_DIR > 0
  #define Y_HOME_TO_MAX 1
#elif Y_HOME_DIR < 0
  #define Y_HOME_TO_MIN 1
#endif
#if Z_HOME_DIR > 0
  #define Z_HOME_TO_MAX 1
#elif Z_HOME_DIR < 0
  #define Z_HOME_TO_MIN 1
#endif
#if I_HOME_DIR > 0
  #define I_HOME_TO_MAX 1
#elif I_HOME_DIR < 0
  #define I_HOME_TO_MIN 1
#endif
#if J_HOME_DIR > 0
  #define J_HOME_TO_MAX 1
#elif J_HOME_DIR < 0
  #define J_HOME_TO_MIN 1
#endif
#if K_HOME_DIR > 0
  #define K_HOME_TO_MAX 1
#elif K_HOME_DIR < 0
  #define K_HOME_TO_MIN 1
#endif

/**
 * Conditionals based on the type of Bed Probe
 */
#if HAS_BED_PROBE
  #if DISABLED(NOZZLE_AS_PROBE)
    #define HAS_PROBE_XY_OFFSET 1
  #endif
  #if DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) && !BOTH(DELTA, SENSORLESS_PROBING)
    #define HAS_CUSTOM_PROBE_PIN 1
  #endif
  #if Z_HOME_TO_MIN && (!HAS_CUSTOM_PROBE_PIN || ENABLED(USE_PROBE_FOR_Z_HOMING))
    #define HOMING_Z_WITH_PROBE 1
  #endif
  #ifndef Z_PROBE_LOW_POINT
    #define Z_PROBE_LOW_POINT -5
  #endif
  #if ENABLED(Z_PROBE_ALLEN_KEY)
    #define PROBE_TRIGGERED_WHEN_STOWED_TEST 1 // Extra test for Allen Key Probe
  #endif
  #if MULTIPLE_PROBING > 1
    #if EXTRA_PROBING > 0
      #define TOTAL_PROBING (MULTIPLE_PROBING + EXTRA_PROBING)
    #else
      #define TOTAL_PROBING MULTIPLE_PROBING
    #endif
  #endif
#else
  // Clear probe pin settings when no probe is selected
  #undef Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  #undef USE_PROBE_FOR_Z_HOMING
#endif

#if Z_HOME_TO_MAX
  #define HOME_Z_FIRST // If homing away from BED do Z first
#endif

/**
 * Conditionals based on the type of Bed Leveling
 */
#if ENABLED(AUTO_BED_LEVELING_UBL)
  #undef LCD_BED_LEVELING
  #if ENABLED(DELTA)
    #define UBL_SEGMENTED 1
  #endif
#endif
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT)
  #define ABL_PLANAR 1
#endif
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  #define ABL_USES_GRID 1
#endif
#if ANY(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_3POINT)
  #define HAS_ABL_NOT_UBL 1
#endif
#if ANY(AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL, MESH_BED_LEVELING)
  #define HAS_MESH 1
#endif
#if EITHER(AUTO_BED_LEVELING_UBL, AUTO_BED_LEVELING_3POINT)
  #define NEEDS_THREE_PROBE_POINTS 1
#endif
#if EITHER(HAS_ABL_NOT_UBL, AUTO_BED_LEVELING_UBL)
  #define HAS_ABL_OR_UBL 1
  #if DISABLED(PROBE_MANUALLY)
    #define HAS_AUTOLEVEL 1
  #endif
#endif
#if EITHER(HAS_ABL_OR_UBL, MESH_BED_LEVELING)
  #define HAS_LEVELING 1
  #if DISABLED(AUTO_BED_LEVELING_UBL)
    #define PLANNER_LEVELING 1
  #endif
#endif
#if !HAS_LEVELING
  #undef RESTORE_LEVELING_AFTER_G28
  #undef ENABLE_LEVELING_AFTER_G28
  #undef G29_RETRY_AND_RECOVER
#endif
#if !HAS_LEVELING || EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
  #undef PROBE_MANUALLY
#endif
#if ANY(HAS_BED_PROBE, PROBE_MANUALLY, MESH_BED_LEVELING)
  #define PROBE_SELECTED 1
#endif

#ifdef GRID_MAX_POINTS_X
  #define GRID_MAX_POINTS ((GRID_MAX_POINTS_X) * (GRID_MAX_POINTS_Y))
  #define GRID_LOOP(A,B) LOOP_L_N(A, GRID_MAX_POINTS_X) LOOP_L_N(B, GRID_MAX_POINTS_Y)
#endif

// Slim menu optimizations
#if ENABLED(SLIM_LCD_MENUS)
  #define BOOT_MARLIN_LOGO_SMALL
#endif

/**
 * CoreXY, CoreXZ, and CoreYZ - and their reverse
 */
#if EITHER(COREXY, COREYX)
  #define CORE_IS_XY 1
#endif
#if EITHER(COREXZ, COREZX)
  #define CORE_IS_XZ 1
#endif
#if EITHER(COREYZ, COREZY)
  #define CORE_IS_YZ 1
#endif
#if CORE_IS_XY || CORE_IS_XZ || CORE_IS_YZ
  #define IS_CORE 1
#endif
#if IS_CORE
  #if CORE_IS_XY
    #define CORE_AXIS_1 A_AXIS
    #define CORE_AXIS_2 B_AXIS
    #define NORMAL_AXIS Z_AXIS
  #elif CORE_IS_XZ
    #define CORE_AXIS_1 A_AXIS
    #define NORMAL_AXIS Y_AXIS
    #define CORE_AXIS_2 C_AXIS
  #elif CORE_IS_YZ
    #define NORMAL_AXIS X_AXIS
    #define CORE_AXIS_1 B_AXIS
    #define CORE_AXIS_2 C_AXIS
  #endif
  #define CORESIGN(n) (ANY(COREYX, COREZX, COREZY) ? (-(n)) : (n))
#elif ENABLED(MARKFORGED_XY)
  // Markforged kinematics
  #define CORE_AXIS_1 A_AXIS
  #define CORE_AXIS_2 B_AXIS
  #define NORMAL_AXIS Z_AXIS
#endif

#if ANY(MORGAN_SCARA, MP_SCARA, AXEL_TPARA)
  #define IS_SCARA 1
  #define IS_KINEMATIC 1
#elif ENABLED(DELTA)
  #define IS_KINEMATIC 1
#else
  #define IS_CARTESIAN 1
  #if !IS_CORE
    #define IS_FULL_CARTESIAN 1
  #endif
#endif

#if DISABLED(DELTA)
  #undef DELTA_HOME_TO_SAFE_ZONE
#endif

// This flag indicates some kind of jerk storage is needed
#if EITHER(CLASSIC_JERK, IS_KINEMATIC)
  #define HAS_CLASSIC_JERK 1
#endif

#if DISABLED(CLASSIC_JERK)
  #define HAS_JUNCTION_DEVIATION 1
#endif

// E jerk exists with JD disabled (of course) but also when Linear Advance is disabled on Delta/SCARA
#if ENABLED(CLASSIC_JERK) || (IS_KINEMATIC && DISABLED(LIN_ADVANCE))
  #define HAS_CLASSIC_E_JERK 1
#endif

//
// Serial Port Info
//
#ifdef SERIAL_PORT_2
  #define HAS_MULTI_SERIAL 1
  #ifdef SERIAL_PORT_3
    #define NUM_SERIAL 3
  #else
    #define NUM_SERIAL 2
  #endif
#elif defined(SERIAL_PORT)
  #define NUM_SERIAL 1
#else
  #define NUM_SERIAL 0
  #undef BAUD_RATE_GCODE
#endif
#if SERIAL_PORT == -1 || SERIAL_PORT_2 == -1 || SERIAL_PORT_3 == -1
  #define HAS_USB_SERIAL 1
#endif
#if SERIAL_PORT_2 == -2
  #define HAS_ETHERNET 1
#endif

#if ENABLED(DWIN_CREALITY_LCD)
  #define SERIAL_CATCHALL 0
  #ifndef LCD_SERIAL_PORT
    #define LCD_SERIAL_PORT 3 // Creality 4.x board
  #endif
#endif

// Fallback Stepper Driver types that don't depend on Configuration_adv.h
#ifndef X_DRIVER_TYPE
  #define X_DRIVER_TYPE  A4988
#endif
#ifndef X2_DRIVER_TYPE
  #define X2_DRIVER_TYPE A4988
#endif
#ifndef Y_DRIVER_TYPE
  #define Y_DRIVER_TYPE  A4988
#endif
#ifndef Y2_DRIVER_TYPE
  #define Y2_DRIVER_TYPE A4988
#endif
#ifndef Z_DRIVER_TYPE
  #define Z_DRIVER_TYPE  A4988
#endif
#ifndef Z2_DRIVER_TYPE
  #define Z2_DRIVER_TYPE A4988
#endif
#ifndef Z3_DRIVER_TYPE
  #define Z3_DRIVER_TYPE A4988
#endif
#ifndef Z4_DRIVER_TYPE
  #define Z4_DRIVER_TYPE A4988
#endif
#if E_STEPPERS <= 0
  #undef E0_DRIVER_TYPE
#elif !defined(E0_DRIVER_TYPE)
  #define E0_DRIVER_TYPE A4988
#endif
#if E_STEPPERS <= 1
  #undef E1_DRIVER_TYPE
#elif !defined(E1_DRIVER_TYPE)
  #define E1_DRIVER_TYPE A4988
#endif
#if E_STEPPERS <= 2
  #undef E2_DRIVER_TYPE
#elif !defined(E2_DRIVER_TYPE)
  #define E2_DRIVER_TYPE A4988
#endif
#if E_STEPPERS <= 3
  #undef E3_DRIVER_TYPE
#elif !defined(E3_DRIVER_TYPE)
  #define E3_DRIVER_TYPE A4988
#endif
#if E_STEPPERS <= 4
  #undef E4_DRIVER_TYPE
#elif !defined(E4_DRIVER_TYPE)
  #define E4_DRIVER_TYPE A4988
#endif
#if E_STEPPERS <= 5
  #undef E5_DRIVER_TYPE
#elif !defined(E5_DRIVER_TYPE)
  #define E5_DRIVER_TYPE A4988
#endif
#if E_STEPPERS <= 6
  #undef E6_DRIVER_TYPE
#elif !defined(E6_DRIVER_TYPE)
  #define E6_DRIVER_TYPE A4988
#endif
#if E_STEPPERS <= 7
  #undef E7_DRIVER_TYPE
#elif !defined(E7_DRIVER_TYPE)
  #define E7_DRIVER_TYPE A4988
#endif

// Fallback axis inverting
#ifndef INVERT_X_DIR
  #define INVERT_X_DIR false
#endif
#if HAS_Y_AXIS && !defined(INVERT_Y_DIR)
  #define INVERT_Y_DIR false
#endif
#if HAS_Z_AXIS && !defined(INVERT_Z_DIR)
  #define INVERT_Z_DIR false
#endif
#if LINEAR_AXES >= 4 && !defined(INVERT_I_DIR)
  #define INVERT_I_DIR false
#endif
#if LINEAR_AXES >= 5 && !defined(INVERT_J_DIR)
  #define INVERT_J_DIR false
#endif
#if LINEAR_AXES >= 6 && !defined(INVERT_K_DIR)
  #define INVERT_K_DIR false
#endif
#if HAS_EXTRUDERS && !defined(INVERT_E_DIR)
  #define INVERT_E_DIR false
#endif

/**
 * This setting is also used by M109 when trying to calculate
 * a ballpark safe margin to prevent wait-forever situation.
 */
#ifndef EXTRUDE_MINTEMP
  #define EXTRUDE_MINTEMP 170
#endif

/**
 * TFT Displays
 *
 * Configure parameters for TFT displays:
 *  - TFT_DEFAULT_ORIENTATION
 *  - TFT_DRIVER
 *  - TFT_WIDTH
 *  - TFT_HEIGHT
 *  - TFT_INTERFACE_(SPI|FSMC)
 *  - TFT_COLOR
 *  - GRAPHICAL_TFT_UPSCALE
 */
#if ENABLED(MKS_TS35_V2_0)          // ST7796
  #define TFT_DEFAULT_DRIVER ST7796
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY)
  #define TFT_RES_480x320
  #define TFT_INTERFACE_SPI
#elif ENABLED(ANET_ET5_TFT35)       // ST7796
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY)
  #define TFT_RES_480x320
  #define TFT_INTERFACE_FSMC
#elif ENABLED(ANET_ET4_TFT28)       // ST7789
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_Y)
  #define TFT_RES_320x240
  #define TFT_INTERFACE_FSMC
#elif ENABLED(MKS_ROBIN_TFT24)      // ST7789
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_Y)
  #define TFT_RES_320x240
  #define TFT_INTERFACE_FSMC
#elif ENABLED(MKS_ROBIN_TFT28)      // ST7789
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_Y)
  #define TFT_RES_320x240
  #define TFT_INTERFACE_FSMC
#elif ENABLED(MKS_ROBIN_TFT32)      // ST7789
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_Y)
  #define TFT_RES_320x240
  #define TFT_INTERFACE_FSMC
#elif ENABLED(MKS_ROBIN_TFT35)      // ILI9488
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_X | TFT_INVERT_Y)
  #define TFT_RES_480x320
  #define TFT_INTERFACE_FSMC
#elif ENABLED(MKS_ROBIN_TFT43)
  #define TFT_DRIVER SSD1963
  #define TFT_DEFAULT_ORIENTATION 0
  #define TFT_RES_480x272
  #define TFT_INTERFACE_FSMC
#elif ENABLED(MKS_ROBIN_TFT_V1_1R)  // ILI9328 or R61505
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_X | TFT_INVERT_Y)
  #define TFT_RES_320x240
  #define TFT_INTERFACE_FSMC
#elif EITHER(TFT_TRONXY_X5SA, ANYCUBIC_TFT35) // ILI9488
  #define TFT_DRIVER ILI9488
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_X | TFT_INVERT_Y)
  #define TFT_RES_480x320
  #define TFT_INTERFACE_FSMC
#elif ENABLED(LONGER_LK_TFT28)
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_X | TFT_INVERT_Y)
  #define TFT_RES_320x240
  #define TFT_INTERFACE_FSMC
#elif ENABLED(BIQU_BX_TFT70)        // RGB
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY)
  #define TFT_RES_1024x600
  #define TFT_INTERFACE_LTDC
  #if ENABLED(TOUCH_SCREEN)
    #define TFT_TOUCH_DEVICE_GT911
  #endif
#elif ENABLED(TFT_GENERIC)
  #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_X | TFT_INVERT_Y)
  #if NONE(TFT_RES_320x240, TFT_RES_480x272, TFT_RES_480x320)
    #define TFT_RES_320x240
  #endif
  #if NONE(TFT_INTERFACE_FSMC, TFT_INTERFACE_SPI)
    #define TFT_INTERFACE_SPI
  #endif
#endif

#if ENABLED(TFT_RES_320x240)
  #define TFT_WIDTH  320
  #define TFT_HEIGHT 240
  #define GRAPHICAL_TFT_UPSCALE 2
#elif ENABLED(TFT_RES_480x272)
  #define TFT_WIDTH  480
  #define TFT_HEIGHT 272
  #define GRAPHICAL_TFT_UPSCALE 2
#elif ENABLED(TFT_RES_480x320)
  #define TFT_WIDTH  480
  #define TFT_HEIGHT 320
  #define GRAPHICAL_TFT_UPSCALE 3
#elif ENABLED(TFT_RES_1024x600)
  #define TFT_WIDTH  1024
  #define TFT_HEIGHT 600
  #define GRAPHICAL_TFT_UPSCALE 4
#endif

// FSMC/SPI TFT Panels using standard HAL/tft/tft_(fsmc|spi|ltdc).h
#if ENABLED(TFT_INTERFACE_FSMC)
  #define HAS_FSMC_TFT 1
  #if TFT_SCALED_DOGLCD
    #define HAS_FSMC_GRAPHICAL_TFT 1
  #elif HAS_TFT_LVGL_UI
    #define HAS_TFT_LVGL_UI_FSMC 1
  #endif
#elif ENABLED(TFT_INTERFACE_SPI)
  #define HAS_SPI_TFT 1
  #if TFT_SCALED_DOGLCD
    #define HAS_SPI_GRAPHICAL_TFT 1
  #elif HAS_TFT_LVGL_UI
    #define HAS_TFT_LVGL_UI_SPI 1
  #endif
#elif ENABLED(TFT_INTERFACE_LTDC)
  #define HAS_LTDC_TFT 1
  #if TFT_SCALED_DOGLCD
    #define HAS_LTDC_GRAPHICAL_TFT 1
  #elif HAS_TFT_LVGL_UI
    #define HAS_TFT_LVGL_UI_LTDC 1
  #endif
#endif

#if ENABLED(TFT_COLOR_UI)
  #if TFT_HEIGHT == 240
    #if ENABLED(TFT_INTERFACE_SPI)
      #define TFT_320x240_SPI
    #elif ENABLED(TFT_INTERFACE_FSMC)
      #define TFT_320x240
    #endif
  #elif TFT_HEIGHT == 320
    #if ENABLED(TFT_INTERFACE_SPI)
      #define TFT_480x320_SPI
    #elif ENABLED(TFT_INTERFACE_FSMC)
      #define TFT_480x320
    #endif
  #elif TFT_HEIGHT == 272
    #if ENABLED(TFT_INTERFACE_SPI)
      #define TFT_480x272_SPI
    #elif ENABLED(TFT_INTERFACE_FSMC)
      #define TFT_480x272
    #endif
  #elif TFT_HEIGHT == 600
    #if ENABLED(TFT_INTERFACE_LTDC)
      #define TFT_1024x600_LTDC
    #endif
  #endif
#endif

#if EITHER(TFT_320x240, TFT_320x240_SPI)
  #define HAS_UI_320x240 1
#elif EITHER(TFT_480x320, TFT_480x320_SPI)
  #define HAS_UI_480x320 1
#elif EITHER(TFT_480x272, TFT_480x272_SPI)
  #define HAS_UI_480x272 1
#elif defined(TFT_1024x600_LTDC)
  #define HAS_UI_1024x600 1
#endif
#if ANY(HAS_UI_320x240, HAS_UI_480x320, HAS_UI_480x272)
  #define LCD_HEIGHT TERN(TOUCH_SCREEN, 6, 7)   // Fewer lines with touch buttons onscreen
#elif HAS_UI_1024x600
  #define LCD_HEIGHT TERN(TOUCH_SCREEN, 12, 13) // Fewer lines with touch buttons onscreen
#endif

// This emulated DOGM has 'touch/xpt2046', not 'tft/xpt2046'
#if ENABLED(TOUCH_SCREEN)
  #if NONE(TFT_TOUCH_DEVICE_GT911, TFT_TOUCH_DEVICE_XPT2046)
    #define TFT_TOUCH_DEVICE_XPT2046          // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
  #endif
  #if ENABLED(TFT_TOUCH_DEVICE_GT911)         // GT911 Capacitive touch screen such as BIQU_BX_TFT70
    #undef TOUCH_SCREEN_CALIBRATION
    #undef TOUCH_CALIBRATION_AUTO_SAVE
  #endif
  #if !HAS_GRAPHICAL_TFT
    #undef TOUCH_SCREEN
    #if ENABLED(TFT_CLASSIC_UI)
      #define HAS_TOUCH_BUTTONS 1
      #if ENABLED(TFT_TOUCH_DEVICE_GT911)
        #define HAS_CAP_TOUCH_BUTTONS 1
      #else
        #define HAS_RES_TOUCH_BUTTONS 1
      #endif
    #endif
  #endif
#endif

// XPT2046_** Compatibility
#if !(defined(TOUCH_CALIBRATION_X) || defined(TOUCH_CALIBRATION_Y) || defined(TOUCH_OFFSET_X) || defined(TOUCH_OFFSET_Y) || defined(TOUCH_ORIENTATION))
  #if defined(XPT2046_X_CALIBRATION) && defined(XPT2046_Y_CALIBRATION) && defined(XPT2046_X_OFFSET) && defined(XPT2046_Y_OFFSET)
    #define TOUCH_CALIBRATION_X  XPT2046_X_CALIBRATION
    #define TOUCH_CALIBRATION_Y  XPT2046_Y_CALIBRATION
    #define TOUCH_OFFSET_X       XPT2046_X_OFFSET
    #define TOUCH_OFFSET_Y       XPT2046_Y_OFFSET
    #define TOUCH_ORIENTATION    TOUCH_LANDSCAPE
  #endif
#endif

#if ANY(USE_XMIN_PLUG, USE_YMIN_PLUG, USE_ZMIN_PLUG, USE_XMAX_PLUG, USE_YMAX_PLUG, USE_ZMAX_PLUG)
  #define HAS_ENDSTOPS 1
  #define COORDINATE_OKAY(N,L,H) WITHIN(N,L,H)
#else
  #define COORDINATE_OKAY(N,L,H) true
#endif

/**
 * LED Backlight INDEX END
 */
#if defined(NEOPIXEL_BKGD_INDEX_FIRST) && !defined(NEOPIXEL_BKGD_INDEX_LAST)
  #define NEOPIXEL_BKGD_INDEX_LAST NEOPIXEL_BKGD_INDEX_FIRST
#endif