🐛 Fix Longer3D STM32 boot, add Maple test (#22473)

This commit is contained in:
Tanguy Pruvot 2021-08-04 08:14:54 +02:00 committed by Scott Lahteine
parent ac64d6915f
commit 2b2a8355c9
9 changed files with 1299 additions and 9 deletions

View File

@ -61,7 +61,7 @@ jobs:
- STM32F103RC_fysetc
- STM32F103RC_meeb
- jgaurora_a5s_a1
- STM32F103VE_longer
- STM32F103VE_longer_maple
#- mks_robin_maple
- mks_robin_lite
- mks_robin_pro
@ -75,6 +75,7 @@ jobs:
- STM32F103RE_btt
- STM32F103RE_btt_USB
- STM32F103RET6_creality
- STM32F103VE_longer
- STM32F407VE_black
- STM32F401VE_STEVAL
- BIGTREE_BTT002

View File

@ -99,12 +99,19 @@
// Avoid nozzle heat and fan start before serial init
#define BOARD_OPENDRAIN_MOSFETS
#define BOARD_PREINIT() { \
#define BOARD_INIT_OD_PINS() { \
OUT_WRITE_OD(HEATER_0_PIN, 0); \
OUT_WRITE_OD(HEATER_BED_PIN, 0); \
OUT_WRITE_OD(FAN_PIN, 0); \
}
#ifdef MAPLE_STM32F1
// Only Maple Framework allow that early
#define BOARD_PREINIT BOARD_INIT_OD_PINS
#else
#define BOARD_INIT BOARD_INIT_OD_PINS
#endif
//
// PWM for a servo probe
// Other servo devices are not supported on this board!

View File

@ -0,0 +1,289 @@
/*
*******************************************************************************
* Copyright (c) 2020, STMicroelectronics
* All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
*******************************************************************************
* Automatically generated from STM32F103V(F-G)Tx.xml
*/
#include "Arduino.h"
#include "PeripheralPins.h"
/* =====
* Note: Commented lines are alternative possibilities which are not used per default.
* If you change them, you will have to know what you do
* =====
*/
//*** ADC ***
#ifdef HAL_ADC_MODULE_ENABLED
WEAK const PinMap PinMap_ADC[] = {
{PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
//{PA_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0
//{PA_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0
{PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
//{PA_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1
//{PA_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1
{NC, NP, 0}
};
#endif
//*** DAC ***
#if defined(STM32F103xE) || defined(STM32F103xG)
#ifdef HAL_DAC_MODULE_ENABLED
WEAK const PinMap PinMap_DAC[] = {
//{PA_4, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // DAC_OUT1
//{PA_5, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // DAC_OUT2
{NC, NP, 0}
};
#endif
#endif
//*** I2C ***
#ifdef HAL_I2C_MODULE_ENABLED
WEAK const PinMap PinMap_I2C_SDA[] = {
{PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)},
{NC, NP, 0}
};
WEAK const PinMap PinMap_I2C_SCL[] = {
{PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)},
{NC, NP, 0}
};
#endif
//*** PWM ***
#ifdef HAL_TIM_MODULE_ENABLED
WEAK const PinMap PinMap_PWM[] = {
#if 0
{PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM2_CH1
//{PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 1, 0)}, // TIM2_CH1
#if defined(STM32F103xE) || defined(STM32F103xG)
//{PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM5_CH1
#endif
{PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM2_CH2
//{PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 2, 0)}, // TIM2_CH2
#if defined(STM32F103xE) || defined(STM32F103xG)
//{PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM5_CH2
#endif
{PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM2_CH3
//{PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 3, 0)}, // TIM2_CH3
#if defined(STM32F103xE) || defined(STM32F103xG)
//{PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM5_CH3
#endif
#ifdef STM32F103xG
//{PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM9_CH1
#endif
//{PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 4, 0)}, // TIM2_CH4
#if defined(STM32F103xE) || defined(STM32F103xG)
//{PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM2_CH4
{PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM5_CH4
#else
{PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM2_CH4
#endif
#if defined(STM32F103xG)
//{PA_3, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM9_CH2
#endif
{PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM3_CH1
#if defined(STM32F103xG)
//{PA_6, TIM13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM13_CH1
#endif
{PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 1, 1)}, // TIM1_CH1N
//{PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM3_CH2
//{PA_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 1)}, // TIM8_CH1N
#if defined(STM32F103xG)
//{PA_7, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM14_CH1
#endif
{PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM1_CH1
//{PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 1, 0)}, // TIM1_CH1
{PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM1_CH2
//{PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 2, 0)}, // TIM1_CH2
{PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM1_CH3
//{PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 3, 0)}, // TIM1_CH3
{PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM1_CH4
//{PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 4, 0)}, // TIM1_CH4
{PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 1, 0)}, // TIM2_CH1
//{PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 1, 0)}, // TIM2_CH1
//{PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 2, 1)}, // TIM1_CH2N
{PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM3_CH3
//{PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 3, 0)}, // TIM3_CH3
#if defined(STM32F103xE) || defined(STM32F103xG)
//{PB_0, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 1)}, // TIM8_CH2N
#endif
{PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 3, 1)}, // TIM1_CH3N
//{PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM3_CH4
//{PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 4, 0)}, // TIM3_CH4
#if defined(STM32F103xE) || defined(STM32F103xG)
//{PB_1, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 1)}, // TIM8_CH3N
#endif
{PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 2, 0)}, // TIM2_CH2
//{PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 2, 0)}, // TIM2_CH2
{PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 1, 0)}, // TIM3_CH1
{PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 2, 0)}, // TIM3_CH2
{PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM4_CH1
{PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM4_CH2
{PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM4_CH3
#if defined(STM32F103xG)
//{PB_8, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM10_CH1
#endif
{PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM4_CH4
#if defined(STM32F103xG)
//{PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM11_CH1
#endif
{PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 3, 0)}, // TIM2_CH3
//{PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 3, 0)}, // TIM2_CH3
{PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 4, 0)}, // TIM2_CH4
//{PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 4, 0)}, // TIM2_CH4
{PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 1)}, // TIM1_CH1N
{PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 1)}, // TIM1_CH2N
#if defined(STM32F103xG)
//{PB_14, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM12_CH1
#endif
{PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 1)}, // TIM1_CH3N
#if defined(STM32F103xG)
//{PB_15, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM12_CH2
#endif
{PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 1, 0)}, // TIM3_CH1
#if defined(STM32F103xE) || defined(STM32F103xG)
//{PC_6, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM8_CH1
#endif
{PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 2, 0)}, // TIM3_CH2
#if defined(STM32F103xE) || defined(STM32F103xG)
//{PC_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM8_CH2
#endif
{PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 3, 0)}, // TIM3_CH3
//{PC_8, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM8_CH3
{PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 4, 0)}, // TIM3_CH4
#if defined(STM32F103xE) || defined(STM32F103xG)
//{PC_9, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM8_CH4
#endif
{PD_12, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM4_ENABLE, 1, 0)}, // TIM4_CH1
{PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM4_ENABLE, 2, 0)}, // TIM4_CH2
{PD_14, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM4_ENABLE, 3, 0)}, // TIM4_CH3
{PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM4_ENABLE, 4, 0)}, // TIM4_CH4
#if defined(STM32F103xG)
{PE_5, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM9_ENABLE, 1, 0)}, // TIM9_CH1
{PE_6, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM9_ENABLE, 2, 0)}, // TIM9_CH2
#endif
{PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 1, 1)}, // TIM1_CH1N
{PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 1, 0)}, // TIM1_CH1
{PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 2, 1)}, // TIM1_CH2N
{PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 2, 0)}, // TIM1_CH2
{PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 3, 1)}, // TIM1_CH3N
{PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 3, 0)}, // TIM1_CH3
{PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_ENABLE, 4, 0)}, // TIM1_CH4
#endif // if 0
{NC, NP, 0}
};
#endif
//*** SERIAL ***
#ifdef HAL_UART_MODULE_ENABLED
WEAK const PinMap PinMap_UART_TX[] = {
{PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
{PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
//{PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
{NC, NP, 0}
};
WEAK const PinMap PinMap_UART_RX[] = {
{PA_3, USART2, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)},
{PA_10, USART1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)},
//{PB_11, USART3, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)},
{NC, NP, 0}
};
WEAK const PinMap PinMap_UART_RTS[] = {
{NC, NP, 0}
};
WEAK const PinMap PinMap_UART_CTS[] = {
{NC, NP, 0}
};
#endif
//*** SPI ***
WEAK const PinMap PinMap_SPI_MOSI[] = {
{PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
//{PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
{NC, NP, 0}
};
WEAK const PinMap PinMap_SPI_MISO[] = {
{PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
//{PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
{NC, NP, 0}
};
WEAK const PinMap PinMap_SPI_SCLK[] = {
{PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
//{PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
{NC, NP, 0}
};
WEAK const PinMap PinMap_SPI_SSEL[] = {
//{PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
//{PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)},
{NC, NP, 0}
};
//*** No CAN ***
#ifdef HAL_CAN_MODULE_ENABLED
WEAK const PinMap PinMap_CAN_RD[] = {
{NC, NP, 0}
};
WEAK const PinMap PinMap_CAN_TD[] = {
{NC, NP, 0}
};
#endif
//*** No ETHERNET ***
//*** No QUADSPI ***
//*** USB ***
#ifdef HAL_PCD_MODULE_ENABLED
WEAK const PinMap PinMap_USB[] = {
{PA_11, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_NONE)}, // USB_DM
{PA_12, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_NONE)}, // USB_DP
{NC, NP, 0}
};
#endif
//*** No USB_OTG_FS ***
//*** No USB_OTG_HS ***
//*** SD ***
#if defined(STM32F103xE) || defined(STM32F103xG)
#ifdef HAL_SD_MODULE_ENABLED
WEAK const PinMap PinMap_SD[] = {
//{PB_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D4
//{PB_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D5
//{PC_6, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D6
//{PC_7, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D7
{PC_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D0
{PC_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D1
{PC_10, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D2
{PC_11, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D3
{PC_12, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_NONE)}, // SDIO_CK
{PD_2, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_NONE)}, // SDIO_CMD
{NC, NP, 0}
};
#endif
#endif

View File

@ -0,0 +1,32 @@
/* SYS_WKUP */
#if defined(PWR_WAKEUP_PIN1) && defined(HAL_PWR_MODULE_ENABLED) && !defined(HAL_PWR_MODULE_ONLY)
#error PA0 is used by thermal sensor, disable low power wake with -DHAL_PWR_MODULE_ONLY
SYS_WKUP1 = PA_0,
#endif
#ifdef PWR_WAKEUP_PIN2
SYS_WKUP2 = NC,
#endif
#ifdef PWR_WAKEUP_PIN3
SYS_WKUP3 = NC,
#endif
#ifdef PWR_WAKEUP_PIN4
SYS_WKUP4 = NC,
#endif
#ifdef PWR_WAKEUP_PIN5
SYS_WKUP5 = NC,
#endif
#ifdef PWR_WAKEUP_PIN6
SYS_WKUP6 = NC,
#endif
#ifdef PWR_WAKEUP_PIN7
SYS_WKUP7 = NC,
#endif
#ifdef PWR_WAKEUP_PIN8
SYS_WKUP8 = NC,
#endif
/* USB */
#ifdef USBCON
#warning USB feature is not required with a CH340 chip
USB_DM = PA_11,
USB_DP = PA_12,
#endif

View File

@ -0,0 +1,348 @@
/**
******************************************************************************
* @file hal_conf_custom.h for Longer3D STM32F103VE board
* @brief Overrides HAL default configuration file.
******************************************************************************
*/
#pragma once
#ifdef __cplusplus
extern "C" {
#endif
/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
/* ########################## Module Selection ############################## */
/**
* @brief Include the default list of modules to be used in the HAL driver
* and manage module deactivation
*/
#include "stm32yyxx_hal_conf.h"
#ifdef HAL_PWR_MODULE_ENABLED
#undef HAL_PWR_MODULE_ENABLED // only way to disable it
#endif
#if defined(HAL_PWR_MODULE_ENABLED) && !defined(HAL_PWR_MODULE_ONLY)
#define HAL_PWR_MODULE_ONLY // disable low power & PA0 wakeup pin (its T°c pin)
#endif
#ifndef HAL_IWDG_MODULE_ENABLED
#define HAL_IWDG_MODULE_ENABLED // USE_WATCHDOG
#endif
#ifdef HAL_PCD_MODULE_ENABLED
#warning No direct STM32 USB pins on Longer3D board
#undef HAL_PCD_MODULE_ENABLED // USB Device
#endif
#ifdef HAL_HCD_MODULE_ENABLED
#warning No direct STM32 USB pins on Longer3D board
#undef HAL_HCD_MODULE_ENABLED // USB Host
#endif
#ifndef HAL_USART_MODULE_ENABLED
//#define HAL_USART_MODULE_ENABLED // Useless.... UART_MODULE do it
#endif
#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
#undef HAL_CAN_LEGACY_MODULE_ENABLED
#endif
#ifdef HAL_CAN_MODULE_ENABLED
#undef HAL_CAN_MODULE_ENABLED
#endif
#ifdef HAL_DAC_MODULE_ENABLED
#undef HAL_DAC_MODULE_ENABLED
#endif
#ifdef HAL_RTC_MODULE_ENABLED
#undef HAL_RTC_MODULE_ENABLED
#endif
#ifndef HAL_EXTI_MODULE_ENABLED
#define HAL_EXTI_MODULE_ENABLED // for ENDSTOP_INTERRUPTS_FEATURE
#endif
/**
* @brief List of modules in the framework (first ones enabled by default)
*/
//#define HAL_MODULE_ENABLED
//#define HAL_ADC_MODULE_ENABLED
//#define HAL_CORTEX_MODULE_ENABLED
//#define HAL_DAC_MODULE_ENABLED
//#define HAL_DMA_MODULE_ENABLED
//#define HAL_FLASH_MODULE_ENABLED
//#define HAL_GPIO_MODULE_ENABLED
//#define HAL_I2C_MODULE_ENABLED
//#define HAL_PCD_MODULE_ENABLED
//#define HAL_PWR_MODULE_ENABLED
//#define HAL_RCC_MODULE_ENABLED
//#define HAL_RTC_MODULE_ENABLED
//#define HAL_SD_MODULE_ENABLED
//#define HAL_SPI_MODULE_ENABLED
//#define HAL_SRAM_MODULE_ENABLED
//#define HAL_TIM_MODULE_ENABLED
//#define HAL_UART_MODULE_ENABLED
//#define HAL_CAN_MODULE_ENABLED
//#define HAL_CAN_LEGACY_MODULE_ENABLED
//#define HAL_CEC_MODULE_ENABLED
//#define HAL_CRC_MODULE_ENABLED
//#define HAL_ETH_MODULE_ENABLED
//#define HAL_EXTI_MODULE_ENABLED
//#define HAL_HCD_MODULE_ENABLED
//#define HAL_I2S_MODULE_ENABLED
//#define HAL_IRDA_MODULE_ENABLED
//#define HAL_IWDG_MODULE_ENABLED
//#define HAL_NAND_MODULE_ENABLED
//#define HAL_NOR_MODULE_ENABLED
//#define HAL_PCCARD_MODULE_ENABLED
//#define HAL_SMARTCARD_MODULE_ENABLED
//#define HAL_USART_MODULE_ENABLED
//#define HAL_WWDG_MODULE_ENABLED
//#define HAL_MMC_MODULE_ENABLED
/* ########################## Oscillator Values adaptation ####################*/
/**
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
* This value is used by the RCC HAL module to compute the system frequency
* (when HSE is used as system clock source, directly or through the PLL).
*/
#ifndef HSE_VALUE
#define HSE_VALUE 8000000U // Value of the External oscillator in Hz (8 MHz)
#endif
#ifndef HSE_STARTUP_TIMEOUT
#define HSE_STARTUP_TIMEOUT 100U // Time out for HSE start up, in ms
#endif
/**
* @brief Internal High Speed oscillator (HSI) value.
* This value is used by the RCC HAL module to compute the system frequency
* (when HSI is used as system clock source, directly or through the PLL).
*/
#ifndef HSI_VALUE
#define HSI_VALUE 8000000U // Value of the Internal oscillator in Hz
#endif
/**
* @brief Internal Low Speed oscillator (LSI) value.
*/
#ifndef LSI_VALUE
#define LSI_VALUE 40000U // LSI Typical Value in Hz
#endif /*!< Value of the Internal Low Speed oscillator in Hz
The real value may vary depending on the variations
in voltage and temperature. */
/**
* @brief External Low Speed oscillator (LSE) value.
* This value is used by the UART, RTC HAL module to compute the system frequency
*/
#ifndef LSE_VALUE
#define LSE_VALUE 32768U // Value of the External Low Speed oscillator in Hz
#endif
#ifndef LSE_STARTUP_TIMEOUT
#define LSE_STARTUP_TIMEOUT 50U // No 32.7KHz LSE on this board, reduced to avoid delays
#endif
/* Tip: To avoid modifying this file each time you need to use different HSE,
=== you can define the HSE value in your toolchain compiler preprocessor. */
/* ########################### System Configuration ######################### */
/**
* @brief This is the HAL system configuration section
*/
#ifndef VDD_VALUE
#define VDD_VALUE 3300U // Value of VDD in mv
#endif
#ifndef TICK_INT_PRIORITY
#define TICK_INT_PRIORITY 0x00U // tick interrupt priority
#endif
#ifndef USE_RTOS
#define USE_RTOS 0U
#endif
#ifndef PREFETCH_ENABLE
#define PREFETCH_ENABLE 1U
#endif
#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
/* ################## SPI peripheral configuration ########################## */
/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
* Activated: CRC code is present inside driver
* Deactivated: CRC code cleaned from driver
*/
#if !defined(USE_SPI_CRC)
#define USE_SPI_CRC 0
#endif
/* Includes ------------------------------------------------------------------*/
/**
* @brief Include module's header file
*/
#ifdef HAL_RCC_MODULE_ENABLED
#include "stm32f1xx_hal_rcc.h"
#endif /* HAL_RCC_MODULE_ENABLED */
#ifdef HAL_GPIO_MODULE_ENABLED
#include "stm32f1xx_hal_gpio.h"
#endif /* HAL_GPIO_MODULE_ENABLED */
#ifdef HAL_EXTI_MODULE_ENABLED
#include "stm32f1xx_hal_exti.h"
#endif /* HAL_EXTI_MODULE_ENABLED */
#ifdef HAL_DMA_MODULE_ENABLED
#include "stm32f1xx_hal_dma.h"
#endif /* HAL_DMA_MODULE_ENABLED */
#ifdef HAL_ETH_MODULE_ENABLED
#include "stm32f1xx_hal_eth.h"
#endif /* HAL_ETH_MODULE_ENABLED */
#ifdef HAL_CAN_MODULE_ENABLED
#include "stm32f1xx_hal_can.h"
#endif /* HAL_CAN_MODULE_ENABLED */
#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
#include "Legacy/stm32f1xx_hal_can_legacy.h"
#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
#ifdef HAL_CEC_MODULE_ENABLED
#include "stm32f1xx_hal_cec.h"
#endif /* HAL_CEC_MODULE_ENABLED */
#ifdef HAL_CORTEX_MODULE_ENABLED
#include "stm32f1xx_hal_cortex.h"
#endif /* HAL_CORTEX_MODULE_ENABLED */
#ifdef HAL_ADC_MODULE_ENABLED
#include "stm32f1xx_hal_adc.h"
#endif /* HAL_ADC_MODULE_ENABLED */
#ifdef HAL_CRC_MODULE_ENABLED
#include "stm32f1xx_hal_crc.h"
#endif /* HAL_CRC_MODULE_ENABLED */
#ifdef HAL_DAC_MODULE_ENABLED
#include "stm32f1xx_hal_dac.h"
#endif /* HAL_DAC_MODULE_ENABLED */
#ifdef HAL_FLASH_MODULE_ENABLED
#include "stm32f1xx_hal_flash.h"
#endif /* HAL_FLASH_MODULE_ENABLED */
#ifdef HAL_SRAM_MODULE_ENABLED
#include "stm32f1xx_hal_sram.h"
#endif /* HAL_SRAM_MODULE_ENABLED */
#ifdef HAL_NOR_MODULE_ENABLED
#include "stm32f1xx_hal_nor.h"
#endif /* HAL_NOR_MODULE_ENABLED */
#ifdef HAL_I2C_MODULE_ENABLED
#include "stm32f1xx_hal_i2c.h"
#endif /* HAL_I2C_MODULE_ENABLED */
#ifdef HAL_I2S_MODULE_ENABLED
#include "stm32f1xx_hal_i2s.h"
#endif /* HAL_I2S_MODULE_ENABLED */
#ifdef HAL_IWDG_MODULE_ENABLED
#include "stm32f1xx_hal_iwdg.h"
#endif /* HAL_IWDG_MODULE_ENABLED */
#ifdef HAL_PWR_MODULE_ENABLED
#include "stm32f1xx_hal_pwr.h"
#endif /* HAL_PWR_MODULE_ENABLED */
#ifdef HAL_RTC_MODULE_ENABLED
#include "stm32f1xx_hal_rtc.h"
#endif /* HAL_RTC_MODULE_ENABLED */
#ifdef HAL_PCCARD_MODULE_ENABLED
#include "stm32f1xx_hal_pccard.h"
#endif /* HAL_PCCARD_MODULE_ENABLED */
#ifdef HAL_SD_MODULE_ENABLED
#include "stm32f1xx_hal_sd.h"
#endif /* HAL_SD_MODULE_ENABLED */
#ifdef HAL_NAND_MODULE_ENABLED
#include "stm32f1xx_hal_nand.h"
#endif /* HAL_NAND_MODULE_ENABLED */
#ifdef HAL_SPI_MODULE_ENABLED
#include "stm32f1xx_hal_spi.h"
#endif /* HAL_SPI_MODULE_ENABLED */
#ifdef HAL_TIM_MODULE_ENABLED
#include "stm32f1xx_hal_tim.h"
#endif /* HAL_TIM_MODULE_ENABLED */
#ifdef HAL_UART_MODULE_ENABLED
#include "stm32f1xx_hal_uart.h"
#endif /* HAL_UART_MODULE_ENABLED */
#ifdef HAL_USART_MODULE_ENABLED
#include "stm32f1xx_hal_usart.h"
#endif /* HAL_USART_MODULE_ENABLED */
#ifdef HAL_IRDA_MODULE_ENABLED
#include "stm32f1xx_hal_irda.h"
#endif /* HAL_IRDA_MODULE_ENABLED */
#ifdef HAL_SMARTCARD_MODULE_ENABLED
#include "stm32f1xx_hal_smartcard.h"
#endif /* HAL_SMARTCARD_MODULE_ENABLED */
#ifdef HAL_WWDG_MODULE_ENABLED
#include "stm32f1xx_hal_wwdg.h"
#endif /* HAL_WWDG_MODULE_ENABLED */
#ifdef HAL_PCD_MODULE_ENABLED
#include "stm32f1xx_hal_pcd.h"
#endif /* HAL_PCD_MODULE_ENABLED */
#ifdef HAL_HCD_MODULE_ENABLED
#include "stm32f1xx_hal_hcd.h"
#endif /* HAL_HCD_MODULE_ENABLED */
#ifdef HAL_MMC_MODULE_ENABLED
#include "stm32f1xx_hal_mmc.h"
#endif /* HAL_MMC_MODULE_ENABLED */
#define assert_param(expr) ((void)0U)
#ifdef __cplusplus
}
#endif

View File

@ -0,0 +1,189 @@
/*
******************************************************************************
**
** File : LinkerScript.ld
**
** Author : Auto-generated by STM32CubeIDE
**
** Abstract : Linker script for STM32F103V(8/B/C/E/F/GTx Device from STM32F1 series
** 64/128/256/512/768/1024Kbytes FLASH
** 20/20/48/64/64/96/96Kbytes RAM
**
** Set heap size, stack size and stack location according
** to application requirements.
**
** Set memory bank area and size if external memory is used.
**
** Target : STMicroelectronics STM32
**
** Distribution: The file is distributed as is without any warranty
** of any kind.
**
*****************************************************************************
** @attention
**
** <h2><center>&copy; COPYRIGHT(c) 2019 STMicroelectronics</center></h2>
**
** Redistribution and use in source and binary forms, with or without modification,
** are permitted provided that the following conditions are met:
** 1. Redistributions of source code must retain the above copyright notice,
** this list of conditions and the following disclaimer.
** 2. Redistributions in binary form must reproduce the above copyright notice,
** this list of conditions and the following disclaimer in the documentation
** and/or other materials provided with the distribution.
** 3. Neither the name of STMicroelectronics nor the names of its contributors
** may be used to endorse or promote products derived from this software
** without specific prior written permission.
**
** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
**
*****************************************************************************
*/
/* Entry Point */
ENTRY(Reset_Handler)
/* Highest address of the user mode stack */
_estack = 0x20000000 + LD_MAX_DATA_SIZE; /* end of "RAM" Ram type memory */
_Min_Heap_Size = 0x200; /* required amount of heap */
_Min_Stack_Size = 0x400; /* required amount of stack */
/* Memories definition */
MEMORY
{
RAM (xrw) : ORIGIN = 0x20000000, LENGTH = LD_MAX_DATA_SIZE
FLASH (rx) : ORIGIN = 0x8000000 + LD_FLASH_OFFSET, LENGTH = LD_MAX_SIZE - LD_FLASH_OFFSET
}
/* Sections */
SECTIONS
{
/* The startup code into "FLASH" Rom type memory */
.isr_vector :
{
. = ALIGN(4);
KEEP(*(.isr_vector)) /* Startup code */
. = ALIGN(4);
} >FLASH
/* The program code and other data into "FLASH" Rom type memory */
.text :
{
. = ALIGN(4);
*(.text) /* .text sections (code) */
*(.text*) /* .text* sections (code) */
*(.glue_7) /* glue arm to thumb code */
*(.glue_7t) /* glue thumb to arm code */
*(.eh_frame)
KEEP (*(.init))
KEEP (*(.fini))
. = ALIGN(4);
_etext = .; /* define a global symbols at end of code */
} >FLASH
/* Constant data into "FLASH" Rom type memory */
.rodata : {
. = ALIGN(4);
*(.rodata) /* .rodata sections (constants, strings, etc.) */
*(.rodata*) /* .rodata* sections (constants, strings, etc.) */
. = ALIGN(4);
} >FLASH
.ARM.extab : {
. = ALIGN(4);
*(.ARM.extab* .gnu.linkonce.armextab.*)
. = ALIGN(4);
} >FLASH
.ARM : {
. = ALIGN(4);
__exidx_start = .;
*(.ARM.exidx*)
__exidx_end = .;
. = ALIGN(4);
} >FLASH
.preinit_array : {
. = ALIGN(4);
PROVIDE_HIDDEN (__preinit_array_start = .);
KEEP (*(.preinit_array*))
PROVIDE_HIDDEN (__preinit_array_end = .);
. = ALIGN(4);
} >FLASH
.init_array : {
. = ALIGN(4);
PROVIDE_HIDDEN (__init_array_start = .);
KEEP (*(SORT(.init_array.*)))
KEEP (*(.init_array*))
PROVIDE_HIDDEN (__init_array_end = .);
. = ALIGN(4);
} >FLASH
.fini_array : {
. = ALIGN(4);
PROVIDE_HIDDEN (__fini_array_start = .);
KEEP (*(SORT(.fini_array.*)))
KEEP (*(.fini_array*))
PROVIDE_HIDDEN (__fini_array_end = .);
. = ALIGN(4);
} >FLASH
/* Used by the startup to initialize data */
_sidata = LOADADDR(.data);
/* Initialized data sections into "RAM" Ram type memory */
.data : {
. = ALIGN(4);
_sdata = .; /* create a global symbol at data start */
*(.data) /* .data sections */
*(.data*) /* .data* sections */
. = ALIGN(4);
_edata = .; /* define a global symbol at data end */
} >RAM AT> FLASH
/* Uninitialized data section into "RAM" Ram type memory */
. = ALIGN(4);
.bss : {
/* This is used by the startup in order to initialize the .bss secion */
_sbss = .; /* define a global symbol at bss start */
__bss_start__ = _sbss;
*(.bss)
*(.bss*)
*(COMMON)
. = ALIGN(4);
_ebss = .; /* define a global symbol at bss end */
__bss_end__ = _ebss;
} >RAM
/* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
._user_heap_stack : {
. = ALIGN(8);
PROVIDE ( end = . );
PROVIDE ( _end = . );
. = . + _Min_Heap_Size;
. = . + _Min_Stack_Size;
. = ALIGN(8);
} >RAM
/* Remove information from the compiler libraries */
/DISCARD/ : {
libc.a ( * )
libm.a ( * )
libgcc.a ( * )
}
.ARM.attributes 0 : { *(.ARM.attributes) }
}

View File

@ -0,0 +1,249 @@
/*
*******************************************************************************
* Copyright (c) 2019, STMicroelectronics
* All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
*******************************************************************************
*/
#include "pins_arduino.h"
#ifdef __cplusplus
extern "C" {
#endif
// Digital PinName array
const PinName digitalPin[] = {
PA_0, //D0
PA_1, //D1
PA_2, //D2
PA_3, //D3
PA_4, //D4
PA_5, //D5
PA_6, //D6
PA_7, //D7
PA_8, //D8
PA_9, //D9
PA_10, //D10
PA_11, //D11
PA_12, //D12
PA_13, //D13
PA_14, //D14
PA_15, //D15
PB_0, //D16
PB_1, //D17
PB_2, //D18
PB_3, //D19
PB_4, //D20
PB_5, //D21
PB_6, //D22
PB_7, //D23
PB_8, //D24
PB_9, //D25
PB_10, //D26
PB_11, //D27
PB_12, //D28
PB_13, //D29
PB_14, //D30
PB_15, //D31
PC_0, //D32
PC_1, //D33
PC_2, //D34
PC_3, //D35
PC_4, //D36
PC_5, //D37
PC_6, //D38
PC_7, //D39
PC_8, //D40
PC_9, //D41
PC_10, //D42
PC_11, //D43
PC_12, //D44
PC_13, //D45
PC_14, //D46
PC_15, //D47
PD_0, //D48
PD_1, //D49
PD_2, //D50
PD_3, //D51
PD_4, //D52
PD_5, //D53
PD_6, //D54
PD_7, //D55
PD_8, //D56
PD_9, //D57
PD_10, //D58
PD_11, //D59
PD_12, //D60
PD_13, //D61
PD_14, //D62
PD_15, //D63
PE_0, //D64
PE_1, //D65
PE_2, //D66
PE_3, //D67
PE_4, //D68
PE_5, //D69
PE_6, //D70
PE_7, //D71
PE_8, //D72
PE_9, //D73
PE_10, //D74
PE_11, //D75
PE_12, //D76
PE_13, //D77
PE_14, //D78
PE_15, //D79
};
// Analog (Ax) pin number array
const uint32_t analogInputPin[] = {
0, // A0, PA0
1, // A1, PA1
2, // A2, PA2
3, // A3, PA3
4, // A4, PA4
5, // A5, PA5
6, // A6, PA6
7, // A7, PA7
16, // A8, PB0
17, // A9, PB1
32, // A10, PC0
33, // A11, PC1
34, // A12, PC2
35, // A13, PC3
36, // A14, PC4
37, // A15, PC5
};
/******************************************************************************/
/* PLL (clocked by HSE) used as System clock source */
/******************************************************************************/
static bool SetSysClock_PLL_HSE(bool bypass)
{
RCC_OscInitTypeDef RCC_OscInitStruct = {};
RCC_ClkInitTypeDef RCC_ClkInitStruct = {};
RCC_PeriphCLKInitTypeDef PeriphClkInit = {};
bool ret = false;
// Initializes the CPU, AHB and APB busses clocks
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
if (bypass == false) {
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
} else {
RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
}
RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9; // 8Mhz x 9 = 72MHz
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) == HAL_OK) {
// Initializes the CPU, AHB and APB busses clocks
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
| RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) == HAL_OK) {
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC | RCC_PERIPHCLK_USB;
PeriphClkInit.AdcClockSelection = RCC_ADCPCLK2_DIV6;
PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5; // 72/1.5 = 48MHz
#ifndef USBCON
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC;
#endif
if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) == HAL_OK) {
ret = true;
}
}
}
return ret;
}
/******************************************************************************/
/* PLL (clocked by HSI) used as System clock source (64MHz max) */
/******************************************************************************/
bool SetSysClock_PLL_HSI(void)
{
RCC_OscInitTypeDef RCC_OscInitStruct = {};
RCC_ClkInitTypeDef RCC_ClkInitStruct = {};
RCC_PeriphCLKInitTypeDef PeriphClkInit = {};
bool ret = false;
// Initializes the CPU, AHB and APB busses clocks
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI_DIV2; // 4 MHz
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL12; // 48 MHz
#ifndef USBCON
// When the HSI is used as a PLL clock input, the maximum
// system clock frequency that can be achieved is 64 MHz.
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL16; // 64 MHz, stay close to 72 for delay()
#endif
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) == HAL_OK) {
// Initializes the CPU, AHB and APB busses clocks
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
| RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
// FLASH_LATENCY_1 may cause boot loops
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) == HAL_OK) {
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC | RCC_PERIPHCLK_USB;
PeriphClkInit.AdcClockSelection = RCC_ADCPCLK2_DIV4;
PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLL; // requires 48 MHz
#ifndef USBCON
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC;// No USB, RTC nor I2S
PeriphClkInit.AdcClockSelection = RCC_ADCPCLK2_DIV6; // 2 4 6 8
#endif
if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) == HAL_OK) {
ret = true;
}
}
}
return ret;
}
void SystemClock_Config(void)
{
/*
* If HSE_VALUE is not 8MHz and you want use it, then:
* - Redefine HSE_VALUE to the correct HSE_VALUE
* - Redefine SystemClock_Config() with the correct settings
*/
#if HSE_VALUE == 8000000U
// 1- Try to start with HSE and external 8MHz xtal
if (SetSysClock_PLL_HSE(false) == false) {
// 2- If fail try to start with HSE and external clock
if (SetSysClock_PLL_HSE(true) == false) {
#endif
// 3- If fail start with HSI clock
if (SetSysClock_PLL_HSI() == false) {
Error_Handler();
}
#if HSE_VALUE == 8000000U
}
}
#endif
}
#ifdef __cplusplus
}
#endif

View File

@ -0,0 +1,175 @@
#pragma once
#ifdef __cplusplus
extern "C" {
#endif // __cplusplus
// STM32F103VET6 | DIGITAL | ANALOG | USART | TWI | SPI | SPECIAL |
//------------------|-------------|---------------|------------|-----------|----------------------|------------|
#define PA0 0 // | | A0 Nozzle T°c | | | | |
#define PA1 1 // | | A1 Bed T°c | | | | |
#define PA2 2 // | | | USART2_TX | | | |
#define PA3 3 // | | DAC_OUT1** | USART2_RX | | | |
#define PA4 4 // | | DAC_OUT2** | | | SPI1_SS*(wired?) | |
#define PA5 5 // | O | | | | SPI1_SCK EEPROM | |
#define PA6 6 // | I | | | | SPI1_MISO EEPROM | |
#define PA7 7 // | O | | | | SPI1_MOSI EEPROM | |
#define PA8 8 // | Od BED | | | | | |
#define PA9 9 // | | | USART1_TX | | | |
#define PA10 10 // | | | USART1_RX | | | |
#define PA11 11 // | I | | | | | USB_DM |
#define PA12 12 // | I | | | | | USB_DP |
#define PA13 13 // | I | | | | | SWD_SWDIO |
#define PA14 14 // | I | | | | | SWD_SWCLK |
#define PA15 15 // | Od FAN | | | | | |
// |-------------|---------------|------------|-----------|----------------------|------------|
#define PB0 16 // | | | | | | |
#define PB1 17 // | | | | | | |
#define PB2 18 // | I+ | | | | | BOOT1 |
#define PB3 19 // | O X_DIR | | | | | |
#define PB4 20 // | O X_STEP | | | | | |
#define PB5 21 // | O X_EN | | | | | |
#define PB6 22 // | O Y_DIR | | | | | |
#define PB7 23 // | O Y_STEP | | | | | |
#define PB8 24 // | O Y_EN | | | | | |
#define PB9 25 // | O Z_DIR | | | | | |
#define PB10 26 // | I+ | | USART3_TX* | TWI2_SCL* | | |
#define PB11 27 // | I+ | | USART3_RX* | TWI2_SDA* | | |
#define PB12 28 // | O TFT | | | | SPI2_SS | TOUCH_CS |
#define PB13 29 // | O TFT | | | | SPI2_SCK | TOUCH_SCK |
#define PB14 30 // | O TFT | | | | SPI2_MISO (bad>MOSI) | TOUCH_MOSI |
#define PB15 31 // | I TFT | | | | SPI2_MOSI (bad>MISO) | TOUCH_MISO |
// |-------------|---------------|------------|-----------|----------------------|------------|
#define PC0 32 // | I E_OUT | | | | | |
#define PC1 33 // | I+ X_MIN | | | | | |
#define PC2 34 // | O LED | | | | | |
#define PC3 35 // | I+ | | | | | |
#define PC4 36 // | O TFT | | | | | TFT RESET |
#define PC5 37 // | O CS1 | | | | for SPI1 EEPROM CS | |
#define PC6 38 // | I TFT | | | | | TOUCH_INT |
#define PC7 39 // | | | | | | |
#define PC8 40 // | x SDIO | | | | | SD_D0 |
#define PC9 41 // | x SDIO | | | | | SD_D1 |
#define PC10 42 // | x SDIO | | | | | SD_D2 |
#define PC11 43 // | x SDIO | | | | | SD_D3 |
#define PC12 44 // | O SDIO | | | | | SD_CLK |
#define PC13 45 // | I | | | | | |
#define PC14 46 // | I+ Y_MAX | | | | | |
#define PC15 47 // | I+ Y_MIN | | | | | |
// |-------------|---------------|------------|-----------|----------------------|------------|
#define PD0 48 // | O TFT | | | | | OSC_IN D2 |
#define PD1 49 // | O TFT | | | | | OSC_OUT D3 |
#define PD2 50 // | O SDIO | | | | | SD_CMD |
#define PD3 51 // | Od NOZZLE | | | | | |
#define PD4 52 // | O TFT | | | | | FSMC_NOE |
#define PD5 53 // | O TFT | | | | | FSMC_NWE |
#define PD6 54 // | I wired?* | | | | | FSMC_NWAIT*|
#define PD7 55 // | O TFT | | | | | FSMC_NE1/CS|
#define PD8 56 // | O TFT | | | | | FSMC_D13 |
#define PD9 57 // | O TFT | | | | | FSMC_D14 |
#define PD10 58 // | O TFT | | | | | FSMC_D15 |
#define PD11 59 // | O TFT | | | | | FSMC_A16 |
#define PD12 60 // | O TFT | | | | | TFT BL |
#define PD13 61 // | Od PWM* | | | | | SERVO0 |
#define PD14 62 // | O TFT | | | | | FSMC_D00 |
#define PD15 63 // | O TFT | | | | | FSMC_D01 |
// |-------------|---------------|------------|-----------|----------------------|------------|
#define PE0 64 // | O Z_STEP | | | | | |
#define PE1 65 // | O Z_EN | | | | | |
#define PE2 66 // | O E0_DIR | | | | | |
#define PE3 67 // | O E0_STEP | | | | | |
#define PE4 68 // | O E0_EN | | | | | |
#define PE5 69 // | I+ Z_MAX | | | | | |
#define PE6 70 // | I+ Z_MIN | | | | | |
#define PE7 71 // | O TFT | | | | | FSMC_D04 |
#define PE8 72 // | O TFT | | | | | FSMC_D05 |
#define PE9 73 // | O TFT | | | | | FSMC_D06 |
#define PE10 74 // | O TFT | | | | | FSMC_D07 |
#define PE11 75 // | O TFT | | | | | FSMC_D08 |
#define PE12 76 // | O TFT | | | | | FSMC_D09 |
#define PE13 77 // | O TFT | | | | | FSMC_D10 |
#define PE14 78 // | O TFT | | | | | FSMC_D11 |
#define PE15 79 // | O TFT | | | | | FSMC_D12 |
//------------------|-------------|---------------|------------|-----------|----------------------|------------|
// This must be a literal
#define NUM_DIGITAL_PINS 80
#define NUM_ANALOG_INPUTS 16 // 2 first are used, but cant be reduced to 2...
// On-board LED pin number
#ifndef LED_BUILTIN
#define LED_BUILTIN PC2
#endif
// On-board user button (not wired)
#ifndef USER_BTN
#define USER_BTN PC13
#endif
// SPI Definition (SPI1 EEPROM)
#define PIN_SPI_SS PC5
#define PIN_SPI_MOSI PA7
#define PIN_SPI_MISO PA6
#define PIN_SPI_SCK PA5
// I2C Definition (Unused)
#define PIN_WIRE_SDA PB11
#define PIN_WIRE_SCL PB10
// Timer Definitions
// Use TIM6/TIM7 when possible as servo and tone don't need GPIO output pin
#ifndef TIMER_TONE
#define TIMER_TONE TIM6
#endif
#ifndef TIMER_SERVO
#define TIMER_SERVO TIM7
#endif
// UART Definitions
// Define here Serial instance number to map on Serial generic name
#define SERIAL_UART_INSTANCE 1
// Default pin used for 'Serial' instance (linked to CH340 USB port)
#define PIN_SERIAL_RX PA10
#define PIN_SERIAL_TX PA9
#define PIN_SERIAL1_RX PA10
#define PIN_SERIAL1_TX PA9
// Default pin used for 'Serial2' instance (connector exists but unsoldered)
#define PIN_SERIAL2_RX PA3
#define PIN_SERIAL2_TX PA2
// Extra HAL modules
#if defined(STM32F103xE)
//#define HAL_DAC_MODULE_ENABLED (unused or maybe for the eeprom write?)
#define HAL_SD_MODULE_ENABLED
#define HAL_SRAM_MODULE_ENABLED
#endif
#ifdef __cplusplus
} // extern "C"
#endif
/*----------------------------------------------------------------------------
* Arduino objects - C++ only
*----------------------------------------------------------------------------*/
#ifdef __cplusplus
// These serial port names are intended to allow libraries and architecture-neutral
// sketches to automatically default to the correct port name for a particular type
// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
// the first hardware serial port whose RX/TX pins are not dedicated to another use.
//
// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
//
// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
//
// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
//
// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
//
// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
// pins are NOT connected to anything by default.
#define SERIAL_PORT_MONITOR Serial1
#define SERIAL_PORT_HARDWARE Serial1
#define SERIAL_PORT_HARDWARE_OPEN Serial2
#endif

View File

@ -330,19 +330,19 @@ upload_protocol = serial
#
[env:STM32F103VE_longer]
platform = ${common_stm32.platform}
lib_deps = ${common.lib_deps}
https://github.com/tpruvot/STM32_Servo_OpenDrain/archive/2.0.zip
extends = stm32_variant
board = genericSTM32F103VE
board_build.variant = MARLIN_F103Vx
board_build.variant = MARLIN_F103VE_LONGER
board_build.rename = project.bin
board_build.offset = 0x10000
board_upload.offset_address = 0x08010000
build_flags = ${stm32_variant.build_flags}
-DMCU_STM32F103VE -DU20 -DTS_V12 -DLED_BUILTIN=PC2 -UPIN_WIRE_SDA
-UPIN_WIRE_SCL -DPIN_WIRE_SDA=PB11 -DPIN_WIRE_SCL=PB10
-DHAL_DAC_MODULE_DISABLED -DHAL_I2S_MODULE_DISABLED
build_unflags = ${stm32_variant.build_unflags}
-DUSBCON -DUSBD_USE_CDC -DHAL_PCD_MODULE_ENABLED
build_flags = ${stm32_variant.build_flags} -DMCU_STM32F103VE -DU20 -DTS_V12
build_unflags = ${stm32_variant.build_unflags} -DUSBCON -DUSBD_USE_CDC -DHAL_PCD_MODULE_ENABLED
extra_scripts = ${stm32_variant.extra_scripts}
monitor_speed = 250000
debug_tool = stlink
#
# TRIGORILLA PRO (STM32F103ZET6)