Poll *all* enabled endstop pins (#15525)

Marlin/src/feature/backlash.cpp

@@ -123,7 +123,7 @@ void Backlash::add_correction_steps(const int32_t &da, const int32_t &db, const
 }
 
 #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
-  #if USES_Z_MIN_PROBE_ENDSTOP
+  #if HAS_CUSTOM_PROBE_PIN
     #define TEST_PROBE_PIN (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
   #else
     #define TEST_PROBE_PIN (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)

Marlin/src/inc/Conditionals_LCD.h

@@ -501,8 +501,8 @@
 #define PROBE_SELECTED (HAS_BED_PROBE || EITHER(PROBE_MANUALLY, MESH_BED_LEVELING))
 
 #if HAS_BED_PROBE
-  #define USES_Z_MIN_PROBE_ENDSTOP DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
+  #define HAS_CUSTOM_PROBE_PIN  DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
-  #define HOMING_Z_WITH_PROBE      (Z_HOME_DIR < 0 && !USES_Z_MIN_PROBE_ENDSTOP)
+  #define HOMING_Z_WITH_PROBE   (Z_HOME_DIR < 0 && !HAS_CUSTOM_PROBE_PIN)
   #ifndef Z_PROBE_LOW_POINT
     #define Z_PROBE_LOW_POINT -5
   #endif

Marlin/src/inc/Conditionals_post.h

@@ -825,12 +825,12 @@
 // Is an endstop plug used for the Z2 endstop or the bed probe?
 #define IS_Z2_OR_PROBE(A,M) ( \
      (Z_MULTI_ENDSTOPS && Z2_USE_ENDSTOP == _##A##M##_) \
-  || (USES_Z_MIN_PROBE_ENDSTOP && Z_MIN_PROBE_PIN == A##_##M##_PIN ) )
+  || (HAS_CUSTOM_PROBE_PIN && Z_MIN_PROBE_PIN == A##_##M##_PIN ) )
 
 // Is an endstop plug used for the Z3 endstop or the bed probe?
 #define IS_Z3_OR_PROBE(A,M) ( \
      (ENABLED(Z_TRIPLE_ENDSTOPS) && Z3_USE_ENDSTOP == _##A##M##_) \
-  || (USES_Z_MIN_PROBE_ENDSTOP && Z_MIN_PROBE_PIN == A##_##M##_PIN ) )
+  || (HAS_CUSTOM_PROBE_PIN && Z_MIN_PROBE_PIN == A##_##M##_PIN ) )
 
 /**
  * Set ENDSTOPPULLUPS for active endstop switches
@@ -1005,7 +1005,7 @@
 #define HAS_Z2_MAX (PIN_EXISTS(Z2_MAX))
 #define HAS_Z3_MIN (PIN_EXISTS(Z3_MIN))
 #define HAS_Z3_MAX (PIN_EXISTS(Z3_MAX))
-#define HAS_Z_MIN_PROBE_PIN (USES_Z_MIN_PROBE_ENDSTOP && PIN_EXISTS(Z_MIN_PROBE))
+#define HAS_Z_MIN_PROBE_PIN (HAS_CUSTOM_PROBE_PIN && PIN_EXISTS(Z_MIN_PROBE))
 #define HAS_CALIBRATION_PIN (PIN_EXISTS(CALIBRATION))
 
 // ADC Temp Sensors (Thermistor or Thermocouple with amplifier ADC interface)

Marlin/src/module/endstops.cpp

@@ -243,7 +243,7 @@ void Endstops::init() {
     #endif
   #endif
 
-  #if USES_Z_MIN_PROBE_ENDSTOP
+  #if HAS_CUSTOM_PROBE_PIN
     #if ENABLED(ENDSTOPPULLUP_ZMIN_PROBE)
       SET_INPUT_PULLUP(Z_MIN_PROBE_PIN);
     #elif ENABLED(ENDSTOPPULLDOWN_ZMIN_PROBE)
@@ -366,7 +366,7 @@ void Endstops::event_handler() {
     ENDSTOP_HIT_TEST_Y();
     ENDSTOP_HIT_TEST_Z();
 
-    #if USES_Z_MIN_PROBE_ENDSTOP
+    #if HAS_CUSTOM_PROBE_PIN
       #define P_AXIS Z_AXIS
       if (TEST(hit_state, Z_MIN_PROBE)) _ENDSTOP_HIT_ECHO(P, 'P');
     #endif
@@ -443,7 +443,7 @@ void _O2 Endstops::M119() {
   #if HAS_Z3_MAX
     ES_REPORT(Z3_MAX);
   #endif
-  #if USES_Z_MIN_PROBE_ENDSTOP
+  #if HAS_CUSTOM_PROBE_PIN
     print_es_state(READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING, PSTR(MSG_Z_PROBE));
   #endif
   #if HAS_FILAMENT_SENSOR
@@ -538,60 +538,52 @@ void Endstops::update() {
    * Check and update endstops
    */
   #if HAS_X_MIN && !X_SPI_SENSORLESS
-    #if ENABLED(X_DUAL_ENDSTOPS)
     UPDATE_ENDSTOP_BIT(X, MIN);
+    #if ENABLED(X_DUAL_ENDSTOPS)
       #if HAS_X2_MIN
         UPDATE_ENDSTOP_BIT(X2, MIN);
       #else
         COPY_LIVE_STATE(X_MIN, X2_MIN);
       #endif
-    #else
-      UPDATE_ENDSTOP_BIT(X, MIN);
     #endif
   #endif
 
   #if HAS_X_MAX && !X_SPI_SENSORLESS
-    #if ENABLED(X_DUAL_ENDSTOPS)
     UPDATE_ENDSTOP_BIT(X, MAX);
+    #if ENABLED(X_DUAL_ENDSTOPS)
       #if HAS_X2_MAX
         UPDATE_ENDSTOP_BIT(X2, MAX);
       #else
         COPY_LIVE_STATE(X_MAX, X2_MAX);
       #endif
-    #else
-      UPDATE_ENDSTOP_BIT(X, MAX);
     #endif
   #endif
 
   #if HAS_Y_MIN && !Y_SPI_SENSORLESS
-    #if ENABLED(Y_DUAL_ENDSTOPS)
     UPDATE_ENDSTOP_BIT(Y, MIN);
+    #if ENABLED(Y_DUAL_ENDSTOPS)
       #if HAS_Y2_MIN
         UPDATE_ENDSTOP_BIT(Y2, MIN);
       #else
         COPY_LIVE_STATE(Y_MIN, Y2_MIN);
       #endif
-    #else
-      UPDATE_ENDSTOP_BIT(Y, MIN);
     #endif
   #endif
 
   #if HAS_Y_MAX && !Y_SPI_SENSORLESS
-    #if ENABLED(Y_DUAL_ENDSTOPS)
     UPDATE_ENDSTOP_BIT(Y, MAX);
+    #if ENABLED(Y_DUAL_ENDSTOPS)
       #if HAS_Y2_MAX
         UPDATE_ENDSTOP_BIT(Y2, MAX);
       #else
         COPY_LIVE_STATE(Y_MAX, Y2_MAX);
       #endif
-    #else
-      UPDATE_ENDSTOP_BIT(Y, MAX);
     #endif
   #endif
 
   #if HAS_Z_MIN && !Z_SPI_SENSORLESS
-    #if Z_MULTI_ENDSTOPS
     UPDATE_ENDSTOP_BIT(Z, MIN);
+    #if Z_MULTI_ENDSTOPS
       #if HAS_Z2_MIN
         UPDATE_ENDSTOP_BIT(Z2, MIN);
       #else
@@ -604,15 +596,11 @@ void Endstops::update() {
           COPY_LIVE_STATE(Z_MIN, Z3_MIN);
         #endif
       #endif
-    #elif ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
-      UPDATE_ENDSTOP_BIT(Z, MIN);
-    #elif Z_HOME_DIR < 0
-      UPDATE_ENDSTOP_BIT(Z, MIN);
     #endif
   #endif
 
   // When closing the gap check the enabled probe
-  #if USES_Z_MIN_PROBE_ENDSTOP
+  #if HAS_CUSTOM_PROBE_PIN
     UPDATE_ENDSTOP_BIT(Z, MIN_PROBE);
   #endif
 
@@ -632,7 +620,7 @@ void Endstops::update() {
           COPY_LIVE_STATE(Z_MAX, Z3_MAX);
         #endif
       #endif
-    #elif !USES_Z_MIN_PROBE_ENDSTOP || Z_MAX_PIN != Z_MIN_PROBE_PIN
+    #elif !HAS_CUSTOM_PROBE_PIN || Z_MAX_PIN != Z_MIN_PROBE_PIN
       // If this pin isn't the bed probe it's the Z endstop
       UPDATE_ENDSTOP_BIT(Z, MAX);
     #endif
@@ -765,7 +753,7 @@ void Endstops::update() {
         #else
           #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
             if (z_probe_enabled) PROCESS_ENDSTOP(Z, MIN);
-          #elif USES_Z_MIN_PROBE_ENDSTOP
+          #elif HAS_CUSTOM_PROBE_PIN
             if (!z_probe_enabled) PROCESS_ENDSTOP(Z, MIN);
           #else
             PROCESS_ENDSTOP(Z, MIN);
@@ -774,7 +762,7 @@ void Endstops::update() {
       #endif
 
       // When closing the gap check the enabled probe
-      #if USES_Z_MIN_PROBE_ENDSTOP
+      #if HAS_CUSTOM_PROBE_PIN
         if (z_probe_enabled) PROCESS_ENDSTOP(Z, MIN_PROBE);
       #endif
     }
@@ -784,7 +772,7 @@ void Endstops::update() {
           PROCESS_TRIPLE_ENDSTOP(Z, Z2, Z3, MAX);
         #elif ENABLED(Z_DUAL_ENDSTOPS)
           PROCESS_DUAL_ENDSTOP(Z, Z2, MAX);
-        #elif !USES_Z_MIN_PROBE_ENDSTOP || Z_MAX_PIN != Z_MIN_PROBE_PIN
+        #elif !HAS_CUSTOM_PROBE_PIN || Z_MAX_PIN != Z_MIN_PROBE_PIN
           // If this pin is not hijacked for the bed probe
           // then it belongs to the Z endstop
           PROCESS_ENDSTOP(Z, MAX);

Marlin/src/module/probe.cpp

@@ -387,7 +387,7 @@ bool set_probe_deployed(const bool deploy) {
   const xy_pos_t old_xy = current_position;
 
   #if ENABLED(PROBE_TRIGGERED_WHEN_STOWED_TEST)
-    #if USES_Z_MIN_PROBE_ENDSTOP
+    #if HAS_CUSTOM_PROBE_PIN
       #define PROBE_STOWED() (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
     #else
       #define PROBE_STOWED() (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)

Marlin/src/pins/pins.h

@@ -904,7 +904,7 @@
 //
 // Disable unused endstop / probe pins
 //
-#if !USES_Z_MIN_PROBE_ENDSTOP
+#if !HAS_CUSTOM_PROBE_PIN
   #undef Z_MIN_PROBE_PIN
   #define Z_MIN_PROBE_PIN    -1
 #endif

Marlin/src/pins/sam/pins_RURAMPS4D_11.h

@@ -118,7 +118,7 @@
 //#define E3_MS2_PIN         ?
 //#define E3_MS3_PIN         ?
 
-#if USES_Z_MIN_PROBE_ENDSTOP
+#if HAS_CUSTOM_PROBE_PIN
   #define Z_MIN_PROBE_PIN  49
 #endif
 

Marlin/src/pins/sam/pins_RURAMPS4D_13.h

@@ -106,7 +106,7 @@
   #define E2_CS_PIN        61
 #endif
 
-#if USES_Z_MIN_PROBE_ENDSTOP
+#if HAS_CUSTOM_PROBE_PIN
   #define Z_MIN_PROBE_PIN  49
 #endif