Commit Graph

795 Commits

Author SHA1 Message Date
Scott Lahteine
bc50db9cf6 Implement PID_ADD_EXTRUSION_RATE 2015-09-12 07:53:20 -05:00
Scott Lahteine
fabf3ae4a0 Add final Z raise after Delta probe 2015-09-12 07:23:24 -05:00
Shane Francis
4c8330c15c Trim Adjustments for Delta Configurations 2015-09-03 01:05:33 -05:00
Scott Lahteine
962120d1d2 Fix spacing in some conditional blocks 2015-08-27 20:59:09 -05:00
Richard Wackerbarth
20b4772155 Create DEBUG_LEVELING_FEATURE 2015-08-27 20:52:08 -05:00
Scott Lahteine
194f98ff95 Debug messages for homing and leveling 2015-08-27 20:52:08 -05:00
Richard Wackerbarth
6292d9e815 Rename ENABLE_AUTO_BED_LEVELING
With the introduction of the #if ENABLED(…)

reads better than
2015-08-27 20:52:08 -05:00
Christian Lefrançois
9897a9147c Update ABL comments (PR#95)
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
2015-08-26 05:51:38 -05:00
Scott Lahteine
23d742bf06 Don't free the stack array plane_equation_coefficients (PR#83) 2015-08-16 06:53:24 -05:00
Scott Lahteine
e3b1e08777 Patch G30 to use raise_z_for_servo (PR#73) 2015-08-15 21:47:04 -05:00
Scott Lahteine
a1eb90d5c0 Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET 2015-08-12 21:26:32 -05:00
Scott Lahteine
91122277f4 Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes 2015-08-12 21:26:25 -05:00
AnHardt
5707a2c3d5 indexindexIntoAB is only vald for !DELTA 2015-08-11 17:32:11 -05:00
AnHardt
d8860f9ad9 Alway end at the same point
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
2015-08-11 17:32:11 -05:00
AnHardt
4ca8f4a9a7 Always zigzag
Use the shortest way between probing-points.
2015-08-11 17:32:11 -05:00
AnHardt
3d23424121 Add array indexIntoAB[xx][yy]
and use it.
2015-08-11 17:32:11 -05:00
AnHardt
e2d69f66b2 Make Z_PROBE a Z_MIN_PROBE (PR#65)
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.

Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX  check for the probe in update_endstops().

Using an delta related idea of @clefranc from #61,
extended to the general change for all setups.

Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
2015-08-11 14:41:36 -05:00
Richard Wackerbarth
9d8cc24abf Continue from the line following the M999 (PR#60)
If the printer is going to accept the M999,
then it should continue from that line number.
2015-08-08 08:08:02 -05:00
Scott Lahteine
46453905d6 Apply remaining ENABLED/DISABLED conditionals 2015-08-03 16:04:48 -05:00
Richard Wackerbarth
b227d8c128 Supply a VERSION in a short form for displays
The long descriptor will still be available in M115
2015-08-03 08:21:09 -05:00
AnHardt
4f46df5dab Make bootscreen configurable for the graphic displays
Saves about 473 byte of progmem and 28 bytes of RAM.
2015-08-03 07:13:00 -05:00
Scott Lahteine
b4abb0ae7f Apply ENABLED / DISABLED to Marlin core files (PR#2558) 2015-07-31 01:03:58 -05:00
Scott Lahteine
9d151bb61b servo_endstop_angles -> servo_endstop_angle 2015-07-30 23:35:57 -05:00
Scott Lahteine
1f63293624 servo_endstops -> servo_endstop_id 2015-07-30 23:35:57 -05:00
Scott Lahteine
ed4a6371ad Add HAS_SERVO_ENDSTOPS to simplify conditonals 2015-07-30 23:35:57 -05:00
Scott Lahteine
ae9274be05 Fix minor compiler warnings in for loops 2015-07-30 23:31:58 -05:00
Scott Lahteine
4a58e447a1 Add array size to servo_endstop_angles (PR#2553) 2015-07-30 23:27:38 -05:00
AnHardt
d03f037a92 Get rid of malloc() and free() (PR#2549)
Just the minimal changes to qr_solve.cpp and .h to get rid of malloc() and free().

Saves about 656 bytes of progmem (library-code)
and 22 bytes for static variables.

Should use exactly the same amount of stack as it did before on the heap.
2015-07-30 17:50:31 -05:00
Scott Lahteine
3b2b2313ff Combine if block related to SERVO_ENDSTOPS 2015-07-30 16:39:05 -05:00
Scott Lahteine
0af2a80e06 Make SERVO_ENDSTOP_ANGLES 2-dimensional 2015-07-30 16:38:56 -05:00
Scott Lahteine
9f48798ffd Replace ENABLED with DEFINED for SERVO_ENDSTOPS (PR#2542) 2015-07-30 07:55:29 -05:00
Richard Wackerbarth
ae00fad75b Rename as M100 2015-07-27 20:31:59 -05:00
Richard Wackerbarth
a401d738df There is an echo in here 2015-07-27 20:31:59 -05:00
Richard Wackerbarth
ed7d45e8f5 Memory watcher 2015-07-27 20:31:59 -05:00
Scott Lahteine
bea6739774 Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527) 2015-07-27 20:24:33 -05:00
Scott Lahteine
e4c01f1c7e Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507) 2015-07-26 20:40:27 -05:00
Scott Lahteine
e2957df05c Shorthand for do_blocking_move_to 2015-07-24 22:07:41 -05:00
Scott Lahteine
819c5b9b50 Adjust comment on Z adjustment 2015-07-24 22:07:41 -05:00
Scott Lahteine
5a7356b6fc Patch for G29 final Z position
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
2015-07-24 22:07:41 -05:00
AnHardt
088e09e052 Add forgotten Marlin_main.cpp 2015-07-24 22:04:49 -05:00
Scott Lahteine
b116c096bd Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512)
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
2015-07-24 22:00:25 -05:00
Scott Lahteine
469843427d Reduce code in gcode_M81 (PR#2497) 2015-07-23 08:14:00 -05:00
Scott Lahteine
c66955aaf9 Mark unchanging arrays as const (PR#2494)
The compiler may be able to optimize if it knows an array won’t be
changing.
2015-07-22 21:37:37 -05:00
Scott Lahteine
278aa15301 Add COUNT macro and apply 2015-07-22 18:16:05 -05:00
Scott Lahteine
aac2b9aa9d Reduce code in gcode_M84 (PR#2492)
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
2015-07-22 17:22:01 -05:00
Scott Lahteine
e83eac312e Move plan_arc next to prepare_move 2015-07-19 16:18:46 -05:00
Scott Lahteine
5c5936508d G2/G3 Arcs for Delta
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
2015-07-19 16:18:46 -05:00
Scott Lahteine
3b23ccd366 Patch servos code for move
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
2015-07-19 11:24:23 -07:00
Patrick Bogen
fba4e6241b Specify print format for reporting invalid tmp_extruder (PR#2465) 2015-07-18 16:40:01 -05:00
AnHardt
d15d869267 Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464)
to make clear - it's not a question but an order.
2015-07-18 10:27:21 -05:00
Scott Lahteine
f209b755a5 Move the Z probe as far as needed to trigger the switch (PR#2461) 2015-07-16 20:02:44 -05:00
Scott Lahteine
0f1df62389 Fixup comments in code_seen 2015-07-16 16:40:52 -05:00
Scott Lahteine
2945eb6650 Call code_seen only once per parameter 2015-07-16 16:40:52 -05:00
Scott Lahteine
db23b9b184 Minor tweak to M204 code (PR#2457) 2015-07-16 16:35:13 -05:00
Scott Lahteine
81d42406b7 Move braces in homeaxis to prevent a hanging else (PR#2451) 2015-07-16 10:25:54 -05:00
AnHardt
ed6598adf5 Corrected Bed Height vs. Bed Topology for verbosity > 3
and cleaned out some tabs.

Everything else is a rebased PR#2017 as proposed by @CptanPanic
2015-07-15 19:51:40 -05:00
brian
62302ceb9e Add calculation of difference between auto-correct bed level plane, and measured topo map. 2015-07-15 19:51:40 -05:00
AnHardt
49609f6c14 Activate the new servo.move() function
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
2015-07-15 17:39:43 -05:00
Scott Lahteine
87a872e103 Use st_get_position_mm where possible (PR#2411) 2015-07-12 22:15:54 -05:00
Scott Lahteine
2e0da8abdc Allow N to take a negative argument (PR@2402) 2015-07-12 22:14:25 -05:00
Scott Lahteine
447dbd6fa5 Add STEPPER_RESET_PIN support 2015-07-11 16:04:11 -05:00
Scott Lahteine
6b1b8cb2b3 Also nullify spaces before the checksum asterisk (PR#2409) 2015-07-10 09:03:07 -05:00
Scott Lahteine
4e9d658141 Prevent a hanging SERIAL_ECHO_START in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
6b494c1535 Use disable_all_heaters in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
15190d40df Add extra EOL after M111 2015-07-07 06:59:10 -05:00
AnHardt
d421f5250d Correct the sign of zprobe_zoffset for G29 (PR#@391)
Sign flipped with #2167.
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
2015-07-07 06:55:33 -05:00
Scott Lahteine
52fcc743ab Replace "target" with "destination" in M600 (PR#2374)
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
2015-07-04 05:55:25 -05:00
AnHardt
23c8c5348f Z-height fix V2b (PR#2351)
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
2015-07-02 20:30:40 -05:00
Todd Swindoll
a111fbbd0a z-probe offset fix (PR#2361)
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
2015-07-02 20:28:07 -05:00
Scott Lahteine
9682ed455e Fix comment on M83, add comment to prepare_move 2015-06-28 08:20:19 -05:00
AnHardt
36746143a1 Correct output of M48 (PR#2336)
n_samples is an uint8_t .
Got printouts like:
50 of 2  ...
2015-06-27 06:08:40 -05:00
Scott Lahteine
f6ca5a8da8 Allow "M110 N123" without a checksum 2015-06-26 18:13:54 -05:00
Scott Lahteine
aaad65ff5d Include a comment documenting M110 2015-06-26 18:13:54 -05:00
Scott Lahteine
862c72b030 Put the mandatory test of gcode_N first 2015-06-26 18:13:54 -05:00
Scott Lahteine
30976f9773 Allow M110 to handle a second N argument 2015-06-26 18:13:53 -05:00
Scott Lahteine
5ccb1c9e7d Use millis for M600 audio feedback interval 2015-06-25 20:45:03 -05:00
Scott Lahteine
fb16a83b8a Cleanup M600 documentation comments 2015-06-25 20:45:03 -05:00
Scott Lahteine
97ec224d72 Replace target with destination in M600 2015-06-25 20:45:03 -05:00
Scott Lahteine
4ce9ddbb74 Check the temperature before filament change 2015-06-25 20:45:03 -05:00
AnHardt
722829b058 Move buzzing code to buzzr.h & buzzer.cpp (PR#2307)
at least the lcd independent part from Marlin_main.cpp.
2015-06-22 22:31:48 -04:00
schlotzz
1e9cf905c7 Enable ZigZag AutoBedLeveling on Deltas (PR#2273)
ZigZag has been disabled by fault due to do_topography_map
2015-06-15 20:26:25 -05:00
AnHardt
6ab7b560af Rework buzzing (PR#2296)
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.

Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.

All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.

To do: Check the conditions for the BEEPER-pin in all pin-files.
2015-06-15 06:13:26 -05:00
Scott Lahteine
29122db2fa Fix ULTRA_LCD spelling in HAS_LCD_BUZZ 2015-06-15 06:12:34 -05:00
Scott Lahteine
e2a4a83586 Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281) 2015-06-12 22:39:35 -05:00
MagoKimbra
eb81982fcd Fix error next command in autotune (PR#2274)
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
2015-06-12 07:10:38 -05:00
AnHardt
55b23c896a Optimise out_of_range_error() (PR#2265)
by avoiding the strncopy()
2015-06-12 02:20:40 -05:00
AnHardt
45642b7fe8 Respect DISABLE_AXIS settings (PR#2216)
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
2015-06-11 11:35:05 -05:00
Scott Lahteine
962b107341 Prevent current_command_args from bypassing nul (PR#2270) 2015-06-09 16:07:10 -05:00
Scott Lahteine
ff6081be3a Parse N[0-9]+[ ]* differently (PR #2263)
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
2015-06-08 17:06:49 -05:00
Scott Lahteine
96a3fba8ac Reverse the sign of zprobe_zoffset
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
2015-06-08 05:09:27 -05:00
paclema
8d295547be * Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button. 2015-06-06 19:45:45 -05:00
Richard Wackerbarth
ad09d6a60f 3 Step Allen Key Probe 2015-06-06 17:48:27 -05:00
AnHardt
e400fce271 Merge pull request #2221 from MagoKimbra/Dryrun
Insert Debug DRYRUN Repetier Host compatible
2015-06-03 12:30:48 +02:00
AnHardt
c3fe6e61ae Merge pull request #2229 from AnHardt/position-out-of-range
Fix out_of_range_error()
2015-06-03 09:46:22 +02:00
AnHardt
d1f4471000 Merge pull request #2146 from Wackerbarth/Versioning
Versioning
2015-06-02 18:31:21 +02:00
AnHardt
17b0ec84ed Fix out_of_range_error()
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
2015-06-02 11:50:32 +02:00
AnHardt
35af5ef23e Merge pull request #2225 from Wurstnase/naming
consistency name for multiplier
2015-06-02 10:18:22 +02:00
wurstnase
e7e964432b consistency name for multiplier
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
2015-06-01 22:33:22 +02:00
MagoKimbra
76306f9073 Insert Debug DRYRUN Repetier Host compatible 2015-06-01 18:34:45 +02:00
MagoKimbra
881146bc22 Fix problem Width Cura 2015-06-01 17:25:32 +02:00