MPCNC/Firmware2
1
0
Fork 0
Code Issues 1 Pull Requests Releases Wiki Activity
6,584 Commits 1 Branch 0 Tags 129 MiB
d08867986e
Commit Graph

1627 Commits

Author SHA1 Message Date
Florian Heilmann
d08867986e Add autotemp capabilities to M104 
This allows M104 to pass the F and B parameters to enable autotemp as well
 2016-11-17 11:28:19 -06:00
Scott Lahteine
2330619da0 Merge pull request #5191 from petrzjunior/const 
Replace const bool with #define for consistency
 2016-11-17 03:37:32 -06:00
Petr Zahradník junior
d7ce5d271b
Replace const bool with #define for consistency 2016-11-16 18:55:21 +01:00
Scott Lahteine
5d23e52d75 Merge pull request #5228 from thinkyhead/rc_keep_last_mix 
Fix DIRECT_MIXING_IN_G1 to preserve the previous mix
 2016-11-15 19:12:01 -06:00
Scott Lahteine
99b0c1fe56 Fix DIRECT_MIXING_IN_G1 to preserve the previous mix 2016-11-15 16:12:26 -06:00
Scott Lahteine
410657b050 Fix G30 with limits, print correct probe XY 2016-11-15 14:10:28 -06:00
Scott Lahteine
665b7f3893 Merge pull request #5212 from thinkyhead/rc_mixing_faster 
Store mix factors as reciprocals and multiply
 2016-11-12 18:47:11 -06:00
Scott Lahteine
60cc9342a4 Merge pull request #5188 from thinkyhead/rc_extended_host_support 
Extended host support: M155 Auto temp report, M115 capabilities
 2016-11-12 15:38:06 -06:00
Scott Lahteine
f663220e87 Store Mix factors as reciprocals and multiply 2016-11-12 15:19:18 -06:00
Scott Lahteine
b31a07e261 Stateful M355 with separate P parameter 2016-11-09 03:28:18 -06:00
Scott Lahteine
3c9a838651 Extended capabilities report in M115 2016-11-09 02:32:58 -06:00
Scott Lahteine
68b866b5dd Add M155 - Auto-report temperature with interval 2016-11-09 02:32:58 -06:00
Scott Lahteine
75bfde9945 M155=>M260, M156=>M261 2016-11-08 17:54:54 -06:00
Scott Lahteine
dcfd7c69e8 Merge pull request #5163 from nzinov/RCBugFix 
Improve G30 probing command - add optional arguments
 2016-11-07 11:37:13 -06:00
Scott Lahteine
e765eebfb0 Patch spacing in bilinear grid report 2016-11-07 04:08:25 -06:00
Nikolay Zinov
dea00bbcf1 improve G30 probing 
Add optional parameters
X, Y for probe point
S sets stowing on and off
 2016-11-05 13:22:45 +03:00
Scott Lahteine
176aeafc19 Don't define bilinear_line_to_destination on kinematic setups 2016-11-03 14:10:07 -05:00
Scott Lahteine
236853df22 Corrections to bilinear_line_to_destination 
- Allow more than 9x9 probe points
- Account for the probe starting position
 2016-11-03 04:43:59 -05:00
Scott Lahteine
0115e495fe Fix up Dual X switch blocks 2016-11-02 21:38:50 -05:00
Scott Lahteine
2495ab7af2 Make dual_x_carriage_mode an enumeration 2016-11-02 21:38:49 -05:00
Scott Lahteine
d6c36f5bb9 Fix Z raise with DXC_AUTO_PARK_MODE 2016-11-02 21:36:50 -05:00
Scott Lahteine
0c79553fc5 Cast int to AxisEnum for some accessors 2016-11-02 17:42:24 -05:00
Scott Lahteine
adbf1f7dca Add M355 to the GCodes list. 2016-11-02 16:43:52 -05:00
Scott Lahteine
63efc10599 Merge pull request #5134 from thinkyhead/rc_bilinear_split_lines 
Split cartesian moves on grid boundaries with bilinear ABL
 2016-11-02 16:14:55 -05:00
Scott Lahteine
ee5b8d6dc8 Split moves on grid boundaries with bilinear ABL on cartesian 2016-11-01 08:25:47 -05:00
Scott Lahteine
66744a6076 Merge pull request #5133 from thinkyhead/rc_M355_case_light 
M355 Case light
 2016-11-01 07:51:27 -05:00
Scott Lahteine
955d14acb0 Patch photo pin code style 2016-11-01 06:30:14 -05:00
Stanley
ab3f966f5f Case light G-code M355 
implemented G-Code M355 into Marlin
 2016-11-01 06:30:14 -05:00
Sebastianv650
f9bea7968f BugFix for incorrect E-speed calculation 
The extrusion speed was wrong due to a not high enough precision of
esteps to XY steps, therefore now the target float values are used to
calculate the ratio between XY movement and extrusion speed.
The e_speed_multiplier8 was replaced by an absolute multiplier called
abs_adv_steps_multiplier8, therefore one multiplication and bitshift can
be saved inside the stepper ISR. Due to this, also extruder_advance_k is
better suited inside the planner and not the stepper files any more.
 2016-11-01 08:08:47 +01:00
Scott Lahteine
ff3a8ca0d1 Use NUM_DIGITAL_PINS instead of custom DIO_COUNT 2016-10-31 08:08:03 -05:00
Scott Lahteine
04a1fac029 Some cleanup to M43 2016-10-31 08:08:03 -05:00
Bob-the-Kuhn
c7f1f0dae6 Add endstop monitor & make pins report pretty 2016-10-31 08:08:02 -05:00
Scott Lahteine
396434a445 Fix compiler warning in M145 2016-10-28 20:57:36 -05:00
Scott Lahteine
07bfc45df8 Adjust spacing in gcode_M149 2016-10-28 20:57:36 -05:00
Scott Lahteine
1a2310c494 Make LCD preheat vars an array to reduce code size 2016-10-28 20:57:36 -05:00
Scott Lahteine
50ee749082 Centralize click-handling in the LCD loop 2016-10-28 20:57:21 -05:00
Scott Lahteine
47ad97c35e Merge pull request #5109 from thinkyhead/rc_eeprom_M218_tool_offset 
Save hotend_offset array (M218) in EEPROM
 2016-10-28 20:08:29 -05:00
Scott Lahteine
67ab54185b Save hotend_offset array (M218) in EEPROM 2016-10-28 18:45:23 -05:00
MagoKimbra
dfcdbb437b Fix Command M420 2016-10-28 20:53:48 +02:00
Scott Lahteine
c34dbfb248 Merge pull request #5072 from thinkyhead/rc_preset_auto_fans 
Add predefined AUTO_FAN_PINs to pins files
 2016-10-27 17:12:11 -05:00
Scott Lahteine
c4c53856a4 Merge pull request #5094 from esenapaj/Fix-for-the-PR-#5088 
Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL)
 2016-10-26 21:51:18 -05:00
esenapaj
d5a5042d23 Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL) 2016-10-27 10:32:20 +09:00
Scott Lahteine
3f94b15cef Fix bilinear grid constraints 
Followup to #5090
 2016-10-26 18:11:26 -05:00
Scott Lahteine
ada935de87 Allow TEMP_STAT_LEDS with only one LED defined 2016-10-26 17:51:26 -05:00
Scott Lahteine
f0d673561f Fix for bilinear grid outside bounds 2016-10-26 05:00:03 -05:00
Scott Lahteine
1ba1ec0db9 Handle M108 in M1 also with ULTIPANEL 2016-10-25 23:25:47 -05:00
Greg Cormier
f0aed9dac7 Fix #4995 - M48/G29 on CoreXY maybe others? 2016-10-22 20:45:13 -04:00
Scott Lahteine
3544c3632f Merge pull request #5062 from thinkyhead/rc_warnings_fix 
Warnings fixed redux
 2016-10-22 12:21:36 -05:00
Josef Pavlik
0bd66807b2 fixed warning: extra ; 2016-10-22 11:12:29 -05:00
Scott Lahteine
5f5a55a0de Add a ZERO macro to clear arrays 2016-10-22 10:07:18 -05:00