Scott Lahteine
182c8d7f8f
Dyze High Temp Thermistor Support
2016-07-10 17:59:05 -07:00
Scott Lahteine
1026e5b071
Replace PLA/ABS preheating with generic
2016-07-09 18:06:51 -07:00
Petr Zahradnik
e282d69f63
Print job timer comment changed
2016-07-09 17:57:54 -07:00
Scott Lahteine
683975cf90
Fix spelling in a config comment
2016-06-28 16:49:13 -07:00
Scott Lahteine
10da7ac86c
Combine Z raise before/after options
2016-06-26 13:56:30 -07:00
Scott Lahteine
03c70c1990
SERVO_DEACTIVATION_DELAY => SERVO_DELAY
2016-06-23 14:33:29 -07:00
Scott Lahteine
bd01592816
Goodbye MECHANICAL_PROBE
2016-06-22 17:13:33 -07:00
Scott Lahteine
b590a7dee0
Make Z_RAISE_BETWEEN_PROBINGS a more general option
2016-06-22 14:00:44 -07:00
Scott Lahteine
d50539583a
Make XY_PROBE_SPEED a general probe option
2016-06-22 03:04:47 -07:00
Scott Lahteine
2798499b71
XY_TRAVEL_SPEED => XY_PROBE_SPEED
2016-06-22 02:45:25 -07:00
Scott Lahteine
b0e47608e6
Merge pull request #4108 from esenapaj/Fix-for-PR-#4093
...
Fix for PR #4093 (Make Z Probe options independent of ABL), etc
2016-06-21 18:12:08 -07:00
esenapaj
d583ea852d
Standardize format description of Panel
2016-06-21 20:51:27 +09:00
esenapaj
aa6d35bd49
Move code block of probe to appropriate position
2016-06-21 20:36:46 +09:00
esenapaj
740fb2ce39
Adjust spacing
2016-06-21 19:37:45 +09:00
Scott Lahteine
19fe93a5a9
Clean up configs for Z_MIN_PROBE_REPEATABILITY_TEST
2016-06-21 03:10:46 -07:00
Scott Lahteine
3996242e9d
Allow Z_MIN_PROBE_REPEATABILITY_TEST solo
2016-06-21 01:56:40 -07:00
Scott Lahteine
9beb3f2f5e
Merge pull request #4097 from thinkyhead/rc_fil_runout_cleanup
...
FIL_RUNOUT_INVERTING false by default
2016-06-19 19:46:14 -07:00
Scott Lahteine
f215b30932
Merge pull request #4093 from thinkyhead/rc_probe_without_abl
...
Make Z Probe options independent of ABL
2016-06-19 19:44:25 -07:00
Scott Lahteine
dfbf8b3c2c
FIL_RUNOUT_INVERTING false by default
2016-06-19 19:25:26 -07:00
Scott Lahteine
de12228758
Make Z Probe options independent of ABL
2016-06-19 18:47:27 -07:00
Scott Lahteine
f8c278ce4d
Cartesio UI display option in all configs
2016-06-19 17:39:46 -07:00
Scott Lahteine
bd4ec727e7
Merge pull request #4066 from thinkyhead/rc_M851_with_probe
...
Make M851 standard with a bed probe
2016-06-17 17:32:55 -07:00
Scott Lahteine
fc56a547d1
Rename movement section to motion
2016-06-17 15:19:43 -07:00
Scott Lahteine
1000563d80
Make M851 standard with a bed probe
2016-06-17 15:19:42 -07:00
Scott Lahteine
47ce810f52
Remove support for XY servo endstops
2016-06-17 14:19:17 -07:00
Scott Lahteine
02e5dad29a
Include Croatian in language listings
2016-06-16 16:18:26 -07:00
João Brázio
8ccd97e7cc
Updated all example configuration files
2016-06-12 00:36:15 +01:00
Reid Rankin
16212432c9
G20/21 and M149 support, and code_value() refactor
...
This is an update of MarlinDev PR #196 .
G20/21: support for switching input units between millimeters and
inches.
M149: support for changing input temperature units.
In support of these changes, code_value() and code_value_short() are
replaced with an array of functions which handle converting to the
proper types and/or units.
2016-06-08 16:51:10 -07:00
Scott Lahteine
cd441ce652
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-06-03 17:38:03 -07:00
Scott Lahteine
db0fd021d0
Z raise options independent of ABL so G28 can use them
2016-06-02 16:56:49 -07:00
Scott Lahteine
28fb1f8994
Tweak #endif comment for ABL GRID
2016-06-02 16:56:49 -07:00
Scott Lahteine
a0b000d752
Support for SAV_3DGLCD OLED LCD controller
2016-05-31 14:41:16 -07:00
Edward Patel
92a27c37b3
MBL: Apply https://github.com/MarlinFirmware/Marlin/pull/3903 to example_configurations
2016-05-30 09:50:11 +02:00
Scott Lahteine
fe3122774a
Merge pull request #3806 from thinkyhead/rc_coreyz_support
...
Support for COREYZ. Fixes for COREXY, COREXZ
2016-05-26 18:50:43 -07:00
Scott Lahteine
89e630b2fb
Merge pull request #3808 from thinkyhead/rc_singlenozzle
...
SINGLENOZZLE
2016-05-23 15:52:19 -07:00
Scott Lahteine
95fee8ca81
Add option for CoreYZ kinematics
2016-05-23 13:58:40 -07:00
Scott Lahteine
c5130fd23b
Additional instructions for controller reverse options
2016-05-20 18:14:50 -07:00
Scott Lahteine
69abfef82e
Add "SINGLENOZZLE" extruder option
2016-05-20 15:45:11 -07:00
Scott Lahteine
1a6c72cb57
Apply to the rest of the configs
2016-05-20 11:52:27 -07:00
João Brázio
f9a62f6a8e
Added PRINTJOB_TIMER_AUTOSTART section to example config files
2016-05-14 15:22:45 -07:00
Scott Lahteine
f13c4a9ec4
Merge pull request #3720 from jbrazio/feature/host-keepalive
...
Removes the DISABLE from HOST_KEEPALIVE
2016-05-14 14:39:31 -07:00
Scott Lahteine
14cd0f4c92
Merge pull request #3740 from thinkyhead/rc_lcd_home_options
...
Individual Axis Homing LCD menu items
2016-05-12 11:59:46 -07:00
João Brázio
09150cae79
Individual Axis Homing LCD menu items
2016-05-11 19:28:19 -07:00
Scott Lahteine
4dc4e2063f
Add REVERSE_ENCODER_DIRECTION option
2016-05-11 15:39:28 -07:00
João Brázio
85b2c80838
Updated example configurations
2016-05-11 01:45:49 +01:00
João Brázio
5373ac6373
Updated example configurations
2016-05-10 13:42:00 +01:00
esenapaj
212b17d510
Fix for PR #3526(Configuration.h LCD & SDCard s...
...
Fix for PR #3526(Configuration.h LCD & SDCard section rewrite)
It removes duplicated BQ_LCD_SMART_CONTROLLER.
2016-05-03 21:35:02 +09:00
esenapaj
2fa4bc344c
Some clean-up for example configuration files
...
Some clean-up for example configuration files
Follow-up and fix the PR #3253(Make the Autotune item(s) in the LCD menu optional):
・Update forgotten file(Felix/Configuration_DUAL.h)
Follow-up the PR #3526(Configuration.h LCD & SDCard section rewrite):
・Add section of RigidBot Panel to RepRapWorld/Megatronics/Configuration.h
Follow-up the PR #3576(Z Safe Homing for all):
・Adjust spacing
Follow-up and fix the PR #3625(Print job statistics):
・Update forgotten file(Felix/Configuration_DUAL.h)
・Remove ambiguous character "f" in top of RigidBot/Configuration.h
2016-05-02 21:16:00 +09:00
Scott Lahteine
c3ef9993b9
Merge pull request #3625 from jbrazio/feature/print-counter
...
Print job statistics
2016-04-29 15:31:14 -07:00
João Brázio
e34f4653ef
Fixed a typo on the configuration files
2016-04-29 23:13:59 +01:00
João Brázio
27088e356f
Updated example configuration files
2016-04-29 23:13:59 +01:00
Scott Lahteine
924285afa6
Merge pull request #3641 from thinkyhead/rc_reverse_menu_doc
...
Correct the REVERSE_MENU_DIRECTION comment
2016-04-28 20:28:46 -07:00
Scott Lahteine
f1b00eb12b
Correct the REVERSE_MENU_DIRECTION comment
2016-04-28 20:27:17 -07:00
Scott Lahteine
0c11566f42
Replace LANGUAGE_INCLUDE with LCD_LANGUAGE
2016-04-27 20:06:40 -07:00
Scott Lahteine
259794c0be
Make DISPLAY_CHARSET_HD44780 a single setting
2016-04-27 20:06:40 -07:00
João Brázio
7de0161204
Updated example config files
2016-04-24 05:21:17 +01:00
Scott Lahteine
0c2aa92b07
Z Safe Homing for all
...
The `Z_SAFE_HOMING` feature is coupled with probes and not leveling, so
make it available for general use.
2016-04-20 17:04:52 -07:00
Scott Lahteine
339b5b3e34
Patch more configs with new changes
2016-04-16 19:35:02 -07:00
Scott Lahteine
a8e4d7c135
Merge pull request #3477 from alephobjects/BedTempHysteresis
...
Implementation of M190 bed temp hysteresis
2016-04-15 16:20:58 -07:00
Scott Lahteine
1cc622b167
Fix minor spelling in comments
2016-04-14 20:06:59 -07:00
Scott Lahteine
de8c0baf8b
Update some comments in Configuration.h
2016-04-14 16:41:20 -07:00
gralco
69c00aea4c
Include bed hysteresis setting in the example configs
2016-04-14 08:03:38 -06:00
Scott Lahteine
f8e10ff1d8
Merge pull request #3491 from thinkyhead/rc_mechanical_probe
...
Support for "mechanical probe" with Allen Key as a special case
2016-04-13 20:55:14 -07:00
Scott Lahteine
7eb476597f
Update some comments in Configuration.h
2016-04-13 20:34:42 -07:00
esenapaj
2eb1b102f8
Support for "mechanical probe" with Allen Key as a special case
2016-04-13 20:34:12 -07:00
Scott Lahteine
2eca8d63b3
Add DEFAULT_KEEPALIVE_INTERVAL setting
2016-04-07 19:25:56 -07:00
Scott Lahteine
e5771346a4
Drop DISABLE_M(IN|AX)_ENDSTOPS, replace with individual endstop flags
2016-04-02 16:39:23 -07:00
Scott Lahteine
ffe054c129
Fix comment about host keepalive interval
2016-04-01 17:28:08 -07:00
Scott Lahteine
1a79b13b7a
FILAMENT_SENSOR -> FILAMENT_WIDTH_SENSOR
2016-03-29 20:54:31 -07:00
Scott Lahteine
53cc6cca46
Formalize some dependencies on PIDTEMPBED
2016-03-25 23:50:28 -07:00
Scott Lahteine
4b31c67dce
Add PID_AUTOTUNE_MENU option
2016-03-25 19:31:56 -07:00
Scott Lahteine
0da744b7b0
Further cleanup of comments, partial Doxygen-style
...
Following up on #3231
2016-03-25 00:45:56 -07:00
jbrazio
5e5d250832
Added gplv3 header to all Marlin files
2016-03-24 18:01:20 +00:00
Scott Lahteine
da9d4c4caf
Merge pull request #3206 from esenapaj/patch-5
...
Follow-up the PR #3082 , etc
2016-03-24 00:20:25 -07:00
esenapaj
fc75e6f92d
Follow-up the PR #3082 , etc
...
Follow-up the PR #3082
Follow-up the commit 143ad74b0f5ba0
2016-03-22 20:22:01 +09:00
esenapaj
22299c13c1
Change link to the document
...
documentation/LCDLanguageFont.md moved to http://www.marlinfirmware.org/ at commit 12d0983757http://www.marlinfirmware.org/ isn't working.
2016-03-22 19:58:41 +09:00
Scott Lahteine
be08eb6153
Merge pull request #3194 from jbrazio/feature/add-pt_pt-utf8
...
Add pt_pt-utf8 language pack and fix some minor compiler warnings
2016-03-20 17:42:45 -07:00
Scott Lahteine
d1ff7959b7
Merge pull request #3188 from esenapaj/patch-1
...
follow-up the commit b82d91e
2016-03-20 17:39:52 -07:00
Scott Lahteine
1cc316f1fd
Merge pull request #3082 from thinkyhead/updated_2820
...
This is quite comprehensive. If probes are disabled in any case when they shouldn't be, I'm sure we will hear about it soon.
2016-03-20 17:10:38 -07:00
jbrazio
1aa531a3db
Missing coma comment correction for all config files
2016-03-20 23:21:45 +00:00
jbrazio
68dda08fff
Added pt_pt-utf8 language pack; Fixed some minor compiler warnings; Harmonize file suffix for the current existing UTF8 language packs; Updated all configuration files to reflect the new language packs
2016-03-20 23:14:24 +00:00
esenapaj
468df96b0f
follow-up the commit b82d91e
...
follow-up the commit b82d91eca6
2016-03-20 20:57:14 +09:00
Scott Lahteine
32f75749e4
Merge pull request #3117 from Blue-Marlin/thermal-protection
...
Improve the descriptions for THERMAL_PROTECTION
2016-03-19 23:41:05 -07:00
esenapaj
37eaa1406b
follow-up the PR #3180
2016-03-20 15:33:02 +09:00
esenapaj
198d5d56fd
follow-up the PR #3183
2016-03-20 13:58:05 +09:00
Blue-Marlin
3166aed087
Improve the descriptions for THERMAL_PROTECTION
2016-03-19 14:08:59 +01:00
AnHardt
3f45a1acf9
Check probes only when deployed
...
Aim: Test probes in update_endstops only when activated
Changes:
Configurations
Add define for FIX_MOUNTED_PROBE to handle the situation where formerly ENDSTOPS_ONLY_FOR_HOMING had to be set, or lowering the nozzle below Z_PROBE_OFFSET_FROM_EXTRUDER could give an "endstop hit" message.
Add define for Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to indicate a common situation, that we have a probe but it is connected to an endstop pin
Add some comments
Shift some entries to have related things together.
Conditionals.h
We have a probe (HAS_Z_MIN_PROBE) if one of the pins is defined AND one of the probes is defined.
SanityCheck.h
Add some tests if the probe is connected and if we have defined a probe.
stepper.cpp
Changes to test the probe only when it is deployed (z_probe_is_active).
Test update_endstops() when the probe is deployed.
MarlinMain.cpp
a. set and reset z_probe_is_active in deploy_z_probe(), stow_z_probe() and dock_sled()
b. set and reset z_probe_is_active in the case a z-servo is moved to a defined position. The only remaining unhandled servo move is in M280 where we do not end in a defined position. If you want to handle a probe use M401/402
c. skip deploying/stowing when already deployed/stowed in the dedicated deploy/stow functions.
d. Handle the new FIX_MOUNTED_PROBE in parallel to a servo driven probe/endstop.
To do: In another PR. handle all probes in deploy/stow_z_probe.
Sort out SERVO_LEVELING vs. HAS_SERVO_ENDSTOPS.
2016-03-19 02:00:08 -07:00
Scott Lahteine
7ec7bb31c4
Send a Busy signal to hosts during long processes, wait for input, etc
...
If Marlin is blocking the serial input or command queue for any length
of time (for example more than 2 seconds), it needs to send a message
to serial out to inform the host that it is busy. Marlin should only
send these messages out when busy, and preferably not when trying to
print formatted output.
2016-03-18 22:38:35 -07:00
Scott Lahteine
d56c6af24e
Merge pull request #3114 from thinkyhead/rc_reverse_lcd_menu
...
Option to reverse the click-wheel direction in menus
2016-03-18 15:39:29 -07:00
Scott Lahteine
b8b51d8da8
Add the REVERSE_MENU_DIRECTION option
2016-03-16 04:02:40 -07:00
Scott Lahteine
cc9968f893
Patch spacing in #3140
2016-03-15 01:18:58 -07:00
Scott Lahteine
1c384930f3
Merge pull request #3140 from thinkyhead/rc_fix_macro_expansion
...
Wrap macros to prevent bad expansions
2016-03-15 00:25:34 -07:00
Scott Lahteine
30c3a21d1f
Merge pull request #3112 from thinkyhead/rc_support_MAX31855
2016-03-13 03:30:48 -07:00
Scott Lahteine
f9ded2a7c4
Wrap macros to prevent bad expansions
2016-03-12 22:38:55 -08:00
Scott Lahteine
27f244ba2c
Support MAX31855 as Temperature Sensor -3
2016-03-10 02:49:54 -08:00
Scott Lahteine
ce639b8b03
Group FILAMENT_SENSOR options together
2016-03-10 02:41:37 -08:00
AnHardt
fd5414c6ea
Z_RAISE_BEFORE_HOMING -> MIN_Z_HEIGHT_FOR_HOMING
...
rebased
corrected spelling
changed to #elif for error
Still with MIN_Z_HEIGHT_FOR_HOMING but con be done with (folder wide) search-replace when we have a better name.
2016-03-08 17:50:23 +01:00
esenapaj2
29e09c7c3e
update example configurations
...
update old comments
update or delete deprecated definitions
complement forgotten updates
adjust spacing
some cosmetic changes
2016-03-07 22:03:33 +09:00
Scott Lahteine
13ef12ad3f
Fix power calculations
...
As suggested by @max-pau in #3073 - #3074
2016-03-06 05:51:59 -08:00
Scott Lahteine
5cba0210f2
Small patch to Z_SAFE_HOMING comment
2016-03-06 05:51:58 -08:00
jbrazio
143ad74db7
Update PROBE_OFFSET_FROM_EXTRUDER comment section in all example config
...
files.
2016-03-06 05:51:58 -08:00
Scott Lahteine
e7cf85b922
Merge pull request #3013 from thinkyhead/esenapaj-patch-1
...
Enhanced #3010 - formal Mesh/Manual dependency
2016-03-06 00:30:02 -08:00
Scott Lahteine
eb85342fd9
Merge pull request #2989 from AnHardt/fix2661
...
Pre home display - Stepper release
2016-03-05 21:30:17 -08:00
Scott Lahteine
772460a7b8
Various minor spelling corrections
...
Redo of #2939 rebased against RCBugFix
2016-03-05 20:41:15 -08:00
AnHardt
615bec2329
Activate warning about possible reduced accuracy by default
...
Renamed `WARN_REDUCED_ACCURACY` to `DISABLE_REDUCED_ACCURACY_WARNING`
Changed the condition for blinking from
```
#if ENABLED(WARN_REDUCED_ACCURACY)
```
to
```
#if DISABLED(DISABLE_REDUCED_ACCURACY_WARNING)
```
2016-02-28 23:20:21 +01:00
AnHardt
4b02f33e69
Distribute config-changes to the other configurations
2016-02-28 23:20:04 +01:00
Scott Lahteine
c2e5c6c12c
Nest Manual Bed Leveling options
...
This formalizes the dependency of MANUAL_BED_LEVELING on
MESH_BED_LEVELING
2016-02-20 20:35:10 -08:00
Scott Lahteine
b19b272172
Update configurations with SPI_SPEED
...
- Include aligned comment about new SDSUPPORT behavior
2016-02-17 14:54:09 -08:00
Scott Lahteine
159ff94afd
Remove obsolete HEATER_BED_DUTY_CYCLE_DIVIDER #2977
2016-02-07 08:02:11 -06:00
Ruwan J Egoda Gamage
b58083b0fa
Getting rid of SDEXTRASLOW, SDSLOW variables.
2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
1b7c443628
Adding SDULTRASLOW variable.
...
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
2016-02-07 07:58:52 -06:00
Richard Wackerbarth
0b429461d5
Back port Cosmetic changes
2015-12-10 07:20:52 -06:00
Richard Wackerbarth
e7b40bbe98
Change link to U8glib source
2015-12-10 06:33:29 -06:00
Scott Lahteine
9b23490f01
Clean up spacing in configs
2015-11-12 00:03:21 -06:00
KiteLab
0ad25c6665
Hint for changed behaviour of SDSUPPORT
2015-09-28 11:07:33 -05:00
Richard Wackerbarth
e01f5e1ef7
Cleanup
2015-09-17 10:44:23 -05:00
Mike Cochrane
5e36b64635
SDEXTRASLOW for some SD card readers (PR#176)
...
Add SDEXTRASLOW which runs the SD card at SPI_QUARTER_SPEED. Quarter speed is needed for RIGIDBOT_PANEL
2015-09-14 07:58:08 -05:00
Richard Wackerbarth
6292d9e815
Rename ENABLE_AUTO_BED_LEVELING
...
With the introduction of the #if ENABLED(…)
reads better than
2015-08-27 20:52:08 -05:00
Christian Lefrançois
9897a9147c
Update ABL comments (PR#95)
...
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
2015-08-26 05:51:38 -05:00
Christian Lefrançois
a7822e3ff7
Some renaming of Z_PROBE to Z_MIN_PROBE (PR#91)
...
* Fix a couple of renames omission and macro expansion errors.
2015-08-20 06:04:46 -05:00
AnHardt
e2d69f66b2
Make Z_PROBE a Z_MIN_PROBE (PR#65)
...
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.
Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX check for the probe in update_endstops().
Using an delta related idea of @clefranc from #61 ,
extended to the general change for all setups.
Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
2015-08-11 14:41:36 -05:00
Scott Lahteine
46453905d6
Apply remaining ENABLED/DISABLED conditionals
2015-08-03 16:04:48 -05:00
Richard Wackerbarth
b227d8c128
Supply a VERSION in a short form for displays
...
The long descriptor will still be available in M115
2015-08-03 08:21:09 -05:00
Richard Wackerbarth
329acc852e
Canonize Option flag USE_AUTOMATIC_VERSION
2015-08-03 08:08:37 -05:00
AnHardt
80f2a20842
Enable bootscreen in all Configurations
2015-08-03 07:13:00 -05:00
Scott Lahteine
1e2deff4fd
Rename BTENABLED to BLUETOOTH
...
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
2015-08-02 22:56:50 -05:00
Scott Lahteine
270c766de2
SDCARDDETECT -> SD_DETECT, added docs
...
- `SD_DETECT_PIN` replaces `SDCARDDETECT`
- `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED`
- Revise the description of `SD_DETECT_INVERTED`
- Add a note about the override of `SD_DETECT_INVERTED` in
`Conditionals.h`
2015-08-02 21:59:41 -05:00
Scott Lahteine
37d1879386
Apply overridables to Configuration files
2015-07-31 00:03:36 -05:00
Scott Lahteine
edaaead7e0
Fix comment about SERVO_ENDSTOP_ANGLES
2015-07-30 23:35:57 -05:00
Scott Lahteine
0af2a80e06
Make SERVO_ENDSTOP_ANGLES 2-dimensional
2015-07-30 16:38:56 -05:00
AnHardt
fd0e81b0c7
Distinguish between BUZZER and SPEAKER (PR#2513)
...
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.
There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker
* replace the PWM based tone()-function again with a on-delay-off-delay loop.
Hopefully the last time I touch the beeper code.
2015-07-24 22:10:04 -05:00
AnHardt
8b876241bd
Some more servo code tweaks
...
Just set up the pin. Don't move to a random position.
Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.
SERVO_LEVELING is the wrong condition to deactivate the servos.
Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
2015-07-24 22:04:49 -05:00
Scott Lahteine
90f8ddfc1e
Apply MINIPANEL to other configs
2015-07-23 22:51:41 -05:00
Scott Lahteine
d85861d296
Move macros, add ENABLED/DISABLED, add includes
2015-07-22 18:16:05 -05:00
Scott Lahteine
129f986ccf
Add COREXZ option to configurations
2015-07-19 16:17:03 -05:00
Scott Lahteine
391386dd94
Update configs for new servo deactivation
2015-07-15 19:13:40 -05:00
Scott Lahteine
c3c605c658
Move note about LiquidTWI2 to Configuration.h (PR#2406)
2015-07-09 05:33:17 -05:00
Scott Lahteine
dc40a5f6e0
Patch up more outdated config lines
2015-06-15 20:20:32 -05:00
Scott Lahteine
a274769f4f
Clean up spacing and comments
...
Also clean up some trailing spaces in a few other sources
2015-06-15 20:20:31 -05:00
Scott Lahteine
d3bce05d54
Fix up spacing for filament sensor values
2015-06-15 20:20:31 -05:00
Scott Lahteine
b4b10a57fe
Fix configurator section directives and values lists
2015-06-15 20:20:31 -05:00
Scott Lahteine
bba14dcbe6
Move Z Safe Homing point to the middle of the movement range
2015-06-15 20:20:31 -05:00
Richard Wackerbarth
58941e543e
ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED removed
...
#defining something just to define something else doesn’t
make sense
If you want SDCARDDETECTINVERTED, just define it yourself.
If the previous code was intended to define, undefined and then again define the term, that code is improper.
2015-06-06 21:44:59 -05:00
Ed Boston
08968c29bb
Adding ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED to Examples
2015-06-06 16:40:32 -05:00
AnHardt
d1f4471000
Merge pull request #2146 from Wackerbarth/Versioning
...
Versioning
2015-06-02 18:31:21 +02:00
Jonathan Bastien-Filiatrault
d46d9d998e
Add maximum bed integral term in example configurations.
2015-05-28 12:51:37 -04:00
Richard Wackerbarth
5ea139fd79
Revised Versioning mechanism
2015-05-25 15:53:14 -05:00
Scott Lahteine
38cc0b93c6
Merge pull request #1874 from AnHardt/Bulgarian
...
Introduction of Bulgarian - language_bg.h
2015-05-22 13:59:50 -07:00
Ed Boston
082ed3beed
Propagate Configuration.h changes
...
Updated all the example Configuration.h files for the new display type.
2015-05-19 14:04:57 -07:00
AnHardt
e353d27430
Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into Bulgarian
2015-05-18 23:56:53 +02:00
Scott Lahteine
2445ae3d3a
Combine thermal runaway and watch-period
...
- Make thermal protection for all hotends and/or bed into simple
switches
- Now enable `WATCH_TEMP_PERIOD` when `THERMAL_PROTECTION_HOTENDS` is
enabled
- Move detailed thermal parameters to `Configuration_adv.h`
- Add sanity checks to warn about old configurations
- Change `WATCH_TEMP_PERIOD` to seconds instead of milliseconds
2015-05-10 22:52:01 -07:00
Scott Lahteine
7f3252eea9
Merge pull request #1999 from paclema/Filrunout_configurable_script
...
Added configurable script for filrunout from configuration.h
2015-05-08 04:39:59 -07:00
Scott Lahteine
181ccc884c
Edit thermal runaway description
2015-05-07 20:46:03 -07:00
paclema
aedd580911
Updated all configuration.h examples
2015-05-03 02:28:43 +02:00
Scott Lahteine
425cd46c12
Merge pull request #1993 from AnHardt/TRP-bed
...
Enable TRP for the bed
2015-04-29 19:44:50 -07:00
AnHardt
514d8ac460
Enable TRP for the bed
...
in all Configurations.
2015-04-29 08:47:01 +02:00
Scott Lahteine
2610b8d047
Enable thermal runaway protection by default
2015-04-28 17:40:29 -07:00
AnHardt
b4b19a6cbd
Merge https://github.com/MarlinFirmware/Marlin into Bulgarian
...
Conflicts:
Marlin/Configuration.h
Marlin/configurator/config/Configuration.h
Marlin/example_configurations/Felix/Configuration.h
Marlin/example_configurations/Felix/Configuration_DUAL.h
Marlin/example_configurations/Hephestos/Configuration.h
Marlin/example_configurations/K8200/Configuration.h
Marlin/example_configurations/SCARA/Configuration.h
Marlin/example_configurations/WITBOX/Configuration.h
Marlin/example_configurations/delta/generic/Configuration.h
Marlin/example_configurations/delta/kossel_mini/Configuration.h
Marlin/example_configurations/makibox/Configuration.h
Marlin/example_configurations/tvrrug/Round2/Configuration.h
Conflicts with my Chinese implementation resolved.
2015-04-28 09:24:32 +02:00
Scott Lahteine
0970102950
Remove obsolete STRING_URL
2015-04-27 21:59:14 -07:00
AnHardt
6cba6bcd82
Add 'cn' to the other 'Configuration.h's
2015-04-27 13:24:51 +02:00
Scott Lahteine
5c29fda167
Add a warning for DISABLE_[XYZ] options
2015-04-25 00:46:33 -07:00
Scott Lahteine
3b97a7d446
Merge pull request #1944 from AnHardt/beep2
...
More Beeper clean up
2015-04-23 17:50:02 -07:00
AnHardt
064f2b37d0
More Beeper clean up.
...
Centralised beep code to lcd_buzz().
From gcode_M300() and lcd_quick_feedback().
Enforced max. duration for M300 to 5 seconds.
Corrected description in 'Configuration.h'
LCD_FEEDBACK_FREQUENCY_HZ 0 gives now a silent delay of
LCD_FEEDBACK_FREQUENCY_DURATION_MS.
2015-04-20 11:11:13 +02:00
Ivan Galvez Junquera
b99e63a7bf
Fixed compilation error "error: stray ‘\357’ in program" in several configuration files.
...
Introduced in commit 697ee2dc
2015-04-17 16:10:58 +02:00
Scott Lahteine
ccbe2c4ea3
Apply CUSTOM_MACHINE_NAME to configurations
...
- Replace “Mendel” with “RepRap”
2015-04-10 21:29:42 -07:00
AnHardt
56fc3a4835
bgr -> bg
...
+ update in documentation
2015-04-09 13:09:18 +02:00
Natealus
585eee6549
Z Probe inverting not present in example configs, causes error
...
The line const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to
invert the logic of the endstop is in the main configuration.h but
wasn't present in the example configuration.h's. Causes a compiling
error with Z Probe enabled. Just added it to all the configs. :)
2015-04-08 18:57:30 -06:00
AnHardt
c5961892e3
Bulgarian for all the Configuration.h's
2015-04-09 01:52:13 +02:00
Scott Lahteine
4788b59300
Thermistor values for configurator
2015-04-08 03:12:21 -07:00
Scott Lahteine
7431ef7e2d
Merge branch 'Development' into dev_version
...
Latest upstream commits
2015-04-07 21:14:00 -07:00
Scott Lahteine
eb6e3886f4
Set version to "1.0.3 dev"
2015-04-07 20:38:43 -07:00
Edward Patel
a9ed39b12d
Moved checks into SanityCheck.h + removed previous added checks.
2015-04-07 22:58:08 +02:00
Edward Patel
002340f32c
Merge branch 'Development-Marlin' into Development
2015-04-07 22:49:12 +02:00
Scott Lahteine
967db181d0
Latest upstream commits
2015-04-06 21:46:18 -07:00
Edward Patel
d27c82a450
Added check for Delta printers in Mesh, #error not yet supported.
2015-04-06 23:03:06 +02:00
Edward Patel
9a093b2e8f
Added #error + mention not to enable ABL and Mesh at the same time
2015-04-06 19:38:59 +02:00
Edward Patel
61de6ecd54
Added change to example Configuration.h's
2015-04-05 04:26:35 +02:00
Scott Lahteine
c065da52ec
Spacing and spelling
2015-04-03 22:54:48 -07:00
Scott Lahteine
e0d4368cb5
Minor code cleanup, move NUM_AXIS out of config
2015-04-03 20:45:24 -07:00
Scott Lahteine
a469d796e1
Add cleanups needed for #1772
2015-04-03 18:14:57 -07:00
Scott Lahteine
0e8182bbf2
Additional pin tests, cleanup
2015-04-03 15:31:35 -07:00
Scott Lahteine
cda4bd4ad9
Correct the comment about M206
2015-03-31 03:20:15 -07:00
Scott Lahteine
ba2c7cb467
Update configs with all the latest
2015-03-30 23:24:33 -07:00
Scott Lahteine
5eff15c409
Merge branch 'Development' into fixup_leveling
...
Latest upstream commits
2015-03-25 21:24:38 -07:00
Scott Lahteine
5261d35737
Fix custom m-code behavior
...
Don’t set CUSTOM_M_CODE_SET_Z_PROBE_OFFSET if there’s no Z probe
2015-03-25 21:20:50 -07:00
AnHardt
94330705c7
Move definition of PIDdT back to temperature.h
...
make it unconditional
remove all definitions in the 'Configuration.h's
remove form 'Conditionals.h'
2015-03-25 11:51:41 +01:00
Scott Lahteine
8db4fd7177
Merge branch 'Development' into planner_oh_planner
...
Latest upstream commits
2015-03-23 22:08:50 -07:00
Scott Lahteine
0d81abe1c9
Merge branch 'Development' into config_testing
...
Latest upstream commits
2015-03-23 21:13:04 -07:00
Scott Lahteine
01740fd9c6
Merge branch 'Development' into planner_oh_planner
...
Latest upstream commits
2015-03-23 21:12:36 -07:00
wurstnase
e6f6c6e3a1
fix bad insertion config again
2015-03-23 08:32:48 +01:00
Scott Lahteine
34a41648ab
Merge branch 'Development' into planner_oh_planner
...
Latest upstream commits
2015-03-22 23:40:29 -07:00
Scott Lahteine
4fbb80567e
Get upstream commits
2015-03-22 23:07:22 -07:00
Scott Lahteine
146501215f
Fix mangled probe_pt calls
...
- Address issue #1669
- Remove the TOPO_ORIGIN configuration setting
2015-03-22 21:45:20 -07:00
Scott Lahteine
88e81a4804
Latest upstream commits, plus fixes
...
- Also add Manual Bed Leveling to the rest of the configs
2015-03-21 16:12:57 -07:00
Scott Lahteine
2c9bd15625
Move LCD items to Conditionals.h
...
- `Conditionals.h` is included twice, setting LCD values the first time
2015-03-21 15:24:57 -07:00
Scott Lahteine
63d5d28085
Merge branch 'Development' into config_testing
...
Latest upstream changes
2015-03-20 04:15:18 -07:00
Scott Lahteine
b6d381f863
Divide up Conditionals to get LCD items early
2015-03-20 02:50:28 -07:00
AnHardt
e85061d20d
Added changes to the 'new' Configuration.h s
2015-03-20 10:36:29 +01:00
Scott Lahteine
670006b919
Remove invariant code from Configurations
...
- Add `Conditionals.h` with calculated configuration values
- Add `SanityCheck.h` with checks for configuration errors
- Remove equivalent code from all configurations
- Move error checks from some sources to `SanityCheck.h` also
- Fix initialization of count_direction in stepper.cpp
2015-03-19 22:22:23 -07:00
Scott Lahteine
a686c9878f
Move TOPO_ORIGIN define to Configuration.h
...
- Addressing issue #1608
2015-03-15 15:49:36 -07:00
chrono
12ec557a75
Added DEFAULT_TRAVEL_ACCELERATION
2015-03-14 10:14:13 +00:00
chrono
1d25d510bc
Upstream Merge Fixes
2015-03-14 09:48:30 +00:00
chrono
d8eeddfb93
Updated DUAL Extruder config, added README and enabled NEWPANEL by default
2015-03-04 09:59:58 +00:00
chrono
7540a81106
Minor fixes
2015-03-02 22:55:00 +01:00
chrono
08bc723a3c
Enable PIDBED
2015-03-02 10:26:42 +00:00
chrono
e487bd642b
Updated PR to streamline integration
2015-03-02 09:49:45 +00:00
