Scott Lahteine
bbc2ee6da1
Don't re-init graphical LCD after boot screen
...
Followup to 13a3fb1acc
2017-11-21 18:21:50 -06:00
GMagician
b96ceb4256
[1.1.x] tool change bad behaviours
...
This PR will address two issues reported in #8492 . Just one is left because I don't know if it is an issue or not
1) when no home is done ("no_move" is set) tool change should never move X & Y because... I don't know where I am...only Z should be adjusted to avoid bed collision if other nozzle is lower than current.
2) Since no move no bed level matrix should be applied
When SWITCHING_NOZZLE is enabled and system is homed there are two movements to go to destination, but first can move Z to older position and then crash on the bed
2017-11-20 16:39:32 -06:00
Scott Lahteine
b6dbc4c5c1
Merge pull request #8426 from SteveGotthardt/bugfixes
...
[1.1.x]Update Anet A8 default values from my Anet A8 experience
2017-11-20 15:12:46 -06:00
Bob-the-Kuhn
12b018e619
Merge pull request #8487 from Bob-the-Kuhn/M43-compatibility-1.1.x
...
[1.1.x] M43 end pin correction/compatibility
2017-11-19 11:01:10 -06:00
Bob-the-Kuhn
9b80e1e04a
change to L for end pin for M43 Toggle command
2017-11-18 13:48:53 -06:00
Scott Lahteine
bf6a1816b4
Display volumetric ratio in terms of E mm
2017-11-18 07:03:18 -06:00
Scott Lahteine
4f05a66ee1
Fixes #8472
2017-11-18 05:14:31 -06:00
Scott Lahteine
622d100c30
No retroactive changes with M851 Z
2017-11-18 03:37:07 -06:00
Scott Lahteine
74997a5251
Fix comment in planner.h
2017-11-18 02:30:41 -06:00
Roxy-3D
50148f7185
Update the UBL Probable Area for Delta's
...
This is a non-intuitive change. @oldmcg says in this post https://github.com/MarlinFirmware/Marlin/issues/7572#issuecomment-340641207 that using DELTA_PRINTABLE_RADIUS is better than DELTA_PROBABLE_RADIUS for setting the probe limits. This is because the automatic probe code checks all locations for being reachable by the probe prior to doing the probe.
2017-11-17 16:41:31 -06:00
Scott Lahteine
8f57a3e28a
Apply coding standards to Max7219 code
2017-11-17 15:33:55 -06:00
Scott Lahteine
2511e869e2
Update Configuration.h
2017-11-16 23:18:55 -06:00
Scott Lahteine
aa612124f2
Merge pull request #8452 from tcm0116/1.1.x-pio_deps
...
[1.1.x] Fix PlatformIO dependencies
2017-11-16 22:54:15 -06:00
Scott Lahteine
eb3bdb7550
Fix FILAMENT_LCD_DISPLAY, disabled state, optimize
2017-11-16 17:46:08 -06:00
Thomas Moore
97c19de8b9
Fix PlatformIO dependencies
2017-11-16 15:16:21 -06:00
Scott Lahteine
4e19c59ab3
Miscellaneous cleanup
2017-11-16 01:18:05 -06:00
Scott Lahteine
9cf5b96971
Fix M503 output for M145
...
Fixes #7978
2017-11-15 04:00:39 -06:00
Scott Lahteine
69a710fef1
Add OV() macro for thermistor tables
2017-11-15 03:20:36 -06:00
Scott Lahteine
d2613ce077
Merge pull request #8432 from thinkyhead/bf1_fix_M32_subroutines
...
[1.1] Fix 'M32 P' subroutines
2017-11-15 02:31:21 -06:00
Scott Lahteine
f2e222b9e8
Merge pull request #8419 from RowanMeara/rm-dithering-1.1.x
...
[1.1.x] Fix Software Fan PWM
2017-11-15 02:29:59 -06:00
Scott Lahteine
a6ee4a0468
Apply SDCARD_SORT_ALPHA changes from 2.0.x
2017-11-15 01:09:13 -06:00
Scott Lahteine
d3b8f30818
Fix M32 P subroutine handling
2017-11-15 01:09:06 -06:00
Scott Lahteine
2390f6d3ab
Cleanup, apply standards to SD lib, cardreader
2017-11-15 01:09:06 -06:00
Scott Lahteine
eacb6b6e8b
Fix parser value handling
2017-11-14 23:23:22 -06:00
Steven Gotthardt
7efffc1548
Update Anet A8 default values from my Anet A8 experience
2017-11-14 10:47:30 -07:00
RowanMeara
10e366ebd7
Change dithering behavior to intended.
2017-11-14 00:36:35 -08:00
Scott Lahteine
95590adf07
Make sure leveled[] is enabled for use
2017-11-14 02:12:20 -06:00
Scott Lahteine
8d06cf7b84
Add M114_DETAIL to Configuration_adv.h
2017-11-14 00:06:35 -06:00
Steven Gotthardt
645b586041
Fix warnings for REPRAPWORLD_KEYPAD
2017-11-13 22:25:17 -06:00
Scott Lahteine
069ec3f9a9
Move Filament Width Sensor to Configuration_adv.h
2017-11-13 21:06:40 -06:00
Scott Lahteine
56035e9965
Move mesh test options under G26 option
2017-11-13 21:06:40 -06:00
Scott Lahteine
d65c99f38b
Drop unused LARGE_FLASH option
2017-11-13 15:47:03 -06:00
Scott Lahteine
90c7d28055
Extrudrboard support for Printrboard Rev.F
2017-11-13 15:47:03 -06:00
Scott Lahteine
8b684637bc
Merge pull request #8397 from RowanMeara/rm-M428-1.1.x
...
[1.1.x] Fix M428
2017-11-13 15:11:36 -06:00
Rowan Meara
d2df00bfca
[1.1.x] Fix compilation warnings ( #8395 )
...
* Fix up Travis CI and compile warnings/errors
* No ULTRA_LCD with REPRAP_DISCOUNT_SMART_CONTROLLER
* No point in setting all the endstop plugs
2017-11-13 04:18:19 -06:00
Scott Lahteine
25ec0fecfa
Apply native workspace fixes to G92, G53-59
2017-11-13 01:53:44 -06:00
RowanMeara
227b96b28b
Fix M428
...
This fixes the old implementation of M428 which was broken, did not
match the website, and made no sense.
2017-11-13 01:34:43 -06:00
Scott Lahteine
a2c013c8c7
Fix LCD pins for Printrboard v1
2017-11-13 00:10:27 -06:00
Scott Lahteine
f27196214b
Fix Printrboard pins for parity with 2.0
2017-11-13 00:03:11 -06:00
Scott Lahteine
aa616cd410
No leveling data in M114 without leveling
2017-11-12 23:06:16 -06:00
Scott Lahteine
5926159890
Fix report_current_position
...
Thanks @RowanMeara!
2017-11-12 22:57:57 -06:00
Roxy-3D
c9f88297b8
Provide more clearance for BL-Touch probe
2017-11-12 13:09:10 -06:00
Scott Lahteine
5cc87abb3a
Merge pull request #8381 from thinkyhead/bf1_native_followup
...
[1.1] Remove offsets from soft endstops, tool change
2017-11-11 23:13:40 -06:00
Scott Lahteine
355dfed437
Coding standard patch of M290
2017-11-11 22:16:13 -06:00
Scott Lahteine
802ae73b13
Turn off laser power pin when PWM goes to 0
2017-11-11 22:02:19 -06:00
Scott Lahteine
549c814e8d
Remove offsets from soft endstops, tool change
2017-11-11 21:28:32 -06:00
Scott Lahteine
564fbc8dec
M290 constrain patch
2017-11-11 20:50:16 -06:00
Scott Lahteine
df44bcc5ae
Use do_blocking_move_to where possible
2017-11-10 20:37:41 -06:00
Scott Lahteine
3293823642
Add pre-calculated planner.e_factor
2017-11-10 20:09:59 -06:00
Scott Lahteine
24b302c001
Fix cold/lengthy extrusion handling
2017-11-10 20:09:59 -06:00
