MPCNC/Firmware
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
8,543 Commits 1 Branch 0 Tags 96 MiB
e792c2b234
Commit Graph

7059 Commits

Author SHA1 Message Date
Scott Lahteine
662105c1b6 ADC sensor fix inspired by 'Evgen2' on Twitter 2017-10-14 02:39:13 -05:00
Scott Lahteine
b8ddae61e2 ubl_state no longer needed 2017-10-14 02:39:13 -05:00
Scott Lahteine
ece14af556 Improve LCD leveling value edits 2017-10-14 02:39:13 -05:00
Scott Lahteine
b07a2aa23c Add HAS_MESH conditional 2017-10-14 02:39:12 -05:00
Scott Lahteine
88857e8028 Move fade_scaling_factor_for_z to Planner 2017-10-14 02:10:46 -05:00
Scott Lahteine
8e808fcadc General cleanup, apply const 2017-10-13 16:13:36 -05:00
Scott Lahteine
da93a272a0 Move leveling_is_active to a macro 2017-10-13 16:11:27 -05:00
Scott Lahteine
3d5b10735f Remove obsolete UBL z_offset 2017-10-13 08:23:01 -05:00
gallynero
94228d4522 Enable change feedrate in delta 
Enable change the relative feedrate on a printing job in delta machines with UBL
 2017-10-12 01:55:51 +02:00
Slawomir Ciunczyk
167058b61f Different NEOPIXEL types 
Changes to support NEOPIXEL LED strips
- Support for different NEOPIXEL as defined in Adafruit_NeoPixel.h
- ability to setup startup brightness
- ability to define sequential/non-sequential transition of color change during heating-up
- additional parameter to M150 P<brightness>
 2017-10-10 01:58:40 -05:00
Scott Lahteine
f835245ee1 Merge pull request #7908 from thinkyhead/bf1_goodbye_legacy_advance 
[1.1.x] Remove legacy ADVANCE feature
 2017-10-10 00:31:39 -05:00
Scott Lahteine
38110e220d Segmented manual moves for kinematics 2017-10-09 23:10:17 -05:00
deram
9239fcf0da Allow UBL G29 and G26 to build without a probe 2017-10-09 18:37:53 -05:00
Scott Lahteine
381ebc043f Add support for ST7565-64128N 
Based on #7447 by @Bob-the-Kuhn
 2017-10-09 17:39:03 -05:00
jmdearras
c7e0a49c94 Add some new LCD displays 
- Original CR-10
- MKS Mini Display
 2017-10-09 17:39:03 -05:00
Scott Lahteine
067622fcc6 Apply some tweaks based on 2.0.x 2017-10-09 17:39:03 -05:00
Scott Lahteine
ae256576e1 Bring configs into parity with 2.0.x 2017-10-09 17:38:39 -05:00
Scott Lahteine
cbfcce09fa Remove legacy ADVANCE feature 2017-10-09 04:27:45 -05:00
Scott Lahteine
a21201a713 LCD filename already concatentated 2017-10-07 15:14:58 -05:00
Scott Lahteine
53f2f188f2 LCD filename already concatenated 2017-10-07 15:11:28 -05:00
Scott Lahteine
a6e95c7d25 Fix display issue with SD_ALPHA_SORT caching 2017-10-07 15:07:05 -05:00
Dave Johnson
97e6663bb3 [1.1.x] Auto-enable DISABLE_REDUCED_ACCURACY_WARNING if HOME_AFTER_DEACTIVATE enabled (#7878) 
* Auto-enable DISABLE_REDUCED_ACCURACY_WARNING if HOME_AFTER_DEACTIVATE enabled

If HOME_AFTER_DEACTIVATE, there is no need to warn on LCD since printer will home prior to starting print.  Saves 60 bytes PROGMEM.
add HD44780 too

* Reduce lines used

* Reduce lines used
 2017-10-07 15:00:56 -05:00
Scott Lahteine
e2ceb1b800 Merge pull request #7632 from GMagician/Wrong-sanitycheck-message-fix 
Addressing #7612
 2017-10-07 02:25:35 -05:00
Scott Lahteine
8c93295d62 Merge pull request #7873 from thinkyhead/bf1_anet_encoder_pulses 
[1.1.x] Fixing ANET encoder pulses
 2017-10-07 01:21:14 -05:00
Phr3d13
c26242a553 Fixing #7833 2017-10-07 00:07:24 -05:00
Scott Lahteine
dac5f20a01 Patch SD file draw bug 2017-10-06 23:53:08 -05:00
Scott Lahteine
b211fa4e1f Remove extra NEWPANEL settings in Conditionals_LCD.h 2017-10-06 17:23:32 -05:00
LVD-AC
355cba4aa7 Fixes for G33 2017-10-06 15:52:53 -05:00
Scott Lahteine
e287e14354 Tweak spacing in utf8_mapper.h 2017-10-06 15:11:27 -05:00
Scott Lahteine
5e63ba970d Merge pull request #7862 from thinkyhead/bf1_mapper_c2c3c4_sk 
[1.1.x] Added Slovak C2C3C4 mapper implementation.
 2017-10-06 14:56:26 -05:00
Roman Moravčík
2a46ab288e Added Slovak C2C3C4 mapper implementation. 2017-10-06 14:40:15 -05:00
Scott Lahteine
7999249a5c Set TEMP_SENSOR_0 to 1 in CR-10 example config 
As pointed out in #7692 by @totalitarian
 2017-10-06 14:29:00 -05:00
Scott Lahteine
0ec9a7f090 Fix xon_xoff_state initialization 2017-10-04 12:10:15 -05:00
Scott Lahteine
a47c5c093d Merge pull request #7459 from ejtagle/xon-xoff-sdxfer 
[1.1.x] XON/XOFF serial handshake (for faster transfers to SD)
 2017-10-02 23:52:41 -05:00
Scott Lahteine
bcb8722513 Fix DUAL_X_CARRIAGE manual move 
Addressing #7745
 2017-10-02 23:28:52 -05:00
Scott Lahteine
4c34b3ad9c Stop redundant E4_IS_TMC2130 current control 2017-10-02 23:10:34 -05:00
Scott Lahteine
1b8b5c4b06 Make prepare_move_to_destination_dualx a full move function 2017-10-02 23:10:18 -05:00
Scott Lahteine
4e19ff75b6 XON/XOFF corrections, tweaks, formatting, etc. 2017-10-02 03:52:42 -05:00
Scott Lahteine
94caabf89a Add XON/XOFF options to example configs 2017-10-02 03:52:41 -05:00
Scott Lahteine
f365448338 Merge pull request #7811 from thinkyhead/bf1_fix_resume_print 
[1.1.x] Fix broken M600 resume_print
 2017-10-01 22:54:34 -05:00
GMagician
8ab426c3a4 Updated all examples configurations 
Forgot to update examples configurations. Done now
 2017-10-01 21:04:12 -05:00
GMagician
33d28c24bf Implementing [FR] #7548 
Added new configuration to inhibit XYZ movements when home is not done
 2017-10-01 21:02:42 -05:00
Scott Lahteine
ac70048945 Only MarlinConfig.h ahead of feature block 2017-10-01 20:55:14 -05:00
MasterPIC
40a4a716e1 Fix filament change bug in resume_print 
Expected behaviour: while (auto)extruding the new filament, the nozzle should not move. It should move (from filament replacement position to printing position) only after the user has confirmed the successful filament replacement and extrusion.

Actual behaviour: while (auto)extruding the new filament, the nozzle moves from filament replacement position back to printing position.
So the extrusion step is mixed with the movement required to go back to the printing position.

The provided code seems to be working but probably a better fix is required.
 2017-10-01 18:42:29 -05:00
Scott Lahteine
802f147686 Remove some excess whitepsace 2017-10-01 18:25:04 -05:00
Scott Lahteine
80a0f935a1 Fix G10-G11 by adding a synchronize 
Based on #7792 by @tcm0116
 2017-09-30 17:46:31 -05:00
MasterPIC
7f8ff0a724 Show leveling status on character LCD 2017-09-27 12:18:41 -05:00
Scott Lahteine
723a34d9c7 Add confirmation to Init EEPROM command 2017-09-27 11:27:47 -05:00
Scott Lahteine
2efd5b119d Add USER_SCRIPT_RETURN option 2017-09-27 11:23:34 -05:00
Scott Lahteine
b105e47cb5 Move SERVO0 pin on GT2560 A+ with BLTOUCH enabled 
Based on #7769
 2017-09-27 10:39:44 -05:00
DecoyPlatypus
41dcbe89dd Fixed ST7920_DELAY typo 
Fixed typo where ST7920_DELAY_2 was being #defined after a check for #ifndef ST7920_DELAY_3
 2017-09-27 03:01:09 -05:00
DecoyPlatypus
70a64355f6 Fixed LCD_FOR_MELZI SanityCheck 
Sanity Check for LCD_FOR_MELZI  would fail with "Please select no more than one LCD controller option" any time #define LCD_FOR_MELZI was enabled in Configuration.h, even if there were no other LCD options enabled.
 2017-09-27 03:01:09 -05:00
Scott Lahteine
e37a1ded0d Increase BABYSTEP_MULTIPLICATOR to 100 
Ideally, it should be calculated based on Z steps per unit so that each
babystep corresponds to around 0.025mm. Smaller than this is largely
insignificant for typical layer heights.
 2017-09-27 00:14:26 -05:00
Scott Lahteine
3e28243076 No need for LCD_PINS_Dn when unused 2017-09-27 00:12:20 -05:00
Scott Lahteine
bbb94b8f68 babystepping tweak 2017-09-27 00:12:20 -05:00
Scott Lahteine
a277b43e30 Fix babystep menu display 2017-09-27 00:12:20 -05:00
Scott Lahteine
8a994fb1b1 Fix encoder pulses for G3D_PANEL 2017-09-27 00:12:20 -05:00
Scott Lahteine
ac2ac99e15 Fix bad logic in autostart 
As pointed out by @marcio-ao in #7638
 2017-09-24 17:52:35 -05:00
Scott Lahteine
c1cc79176c Full-featured Creality configs 2017-09-24 16:52:42 -05:00
Scott Lahteine
f25dccd6d1 Disable BABYSTEP_XY by default in all configs 2017-09-24 16:52:42 -05:00
Scott Lahteine
cd09a83cfa Add size note to SDSORT_LIMIT 2017-09-24 16:52:41 -05:00
Scott Lahteine
9bbc2df217 General code cleanup, spacing 2017-09-24 16:52:41 -05:00
Luc Van Daele
74d430cb97 matrix names update (#7697) 
* matrix names update

* symplified names

* new angle normalization

* ABC

* axis

* least squares

* recalc_delta_settings

* endstop_adj

* 0p

* bug
 2017-09-24 01:45:31 -05:00
Scott Lahteine
9d4d53e2fd Update links to old wiki page 2017-09-23 22:06:45 -05:00
Scott Lahteine
00896f1713 Fix LEVEL_BED_CORNERS (No leveling required) 2017-09-23 22:00:45 -05:00
Scott Lahteine
c3a9e95a5f Define drawmenu items once, in ultralcd.cpp 2017-09-23 22:00:45 -05:00
Scott Lahteine
0afd25a010 Fix caselight compile issues 2017-09-23 22:00:44 -05:00
GMagician
5b87843fae Addressing #7612 
Replaced extruder with hotend
 2017-09-07 19:07:36 +02:00
Scott Lahteine
386b74f8c2 Merge pull request #7593 from marcio-ao/bugfix-1.1.x 
Added option for graphical overlay for Z-offset (Resubmission of #7350 and #7586)
 2017-09-02 00:01:38 -05:00
Tannoo
2a963fb5d1 UBL LCD Bugfixes (#7598) 2017-09-01 16:59:06 -05:00
Marcio Teixeira
d69c5317df Added option for graphical overlay for Z-offset 2017-08-31 14:21:39 -06:00
Scott Lahteine
367e1b54ba Merge pull request #7591 from thinkyhead/bf1_misc_patches 
M111: no args reports current flags
 2017-08-31 15:19:29 -05:00
Scott Lahteine
8a184a526a Marlin: Patch G33, allow M111 to give status 2017-08-31 14:35:00 -05:00
Scott Lahteine
353c23b16e Enforce BED_CENTER_AT_0_0 on Delta, SCARA 2017-08-31 14:34:59 -05:00
Scott Lahteine
898f48e331 CNC workspace planes for G5 
According to LinuxCNC, G5 should throw an error if the current plane mode isn't XY.
 2017-08-31 14:29:29 -05:00
Scott Lahteine
5851c2d36f MAX7219 followup (#7564) 
* Add MAX7219_DEBUG to Travis CI testing

* Tweak config and use standard pin naming for MAX7219_DEBUG

* MAX7219: Apply coding standards, use macros, etc.

* Make code work...
 2017-08-31 11:44:43 -05:00
Scott Lahteine
52073f21c5 Merge pull request #7556 from thinkyhead/bf1_slovak_language 
Slovak UTF-8 translation
 2017-08-27 21:05:53 -05:00
Scott Lahteine
321f98f867 Fix servo delay in Folgertech config 2017-08-27 20:53:27 -05:00
jneilliii
36771e9492 Fixes required for Creality CR-10 2017-08-27 20:39:16 -05:00
Roxy-3D
3f0b38ed5d Add Max7219 LED Matrix Debug Support (#7563) 
* Add Max7219 LED Matrix Debug Support

The Max7219 8x8 LED Matrix's are very helpful for debugging new code.
And for that matter, just trying to maximize printer settings without
causing stuttering.

The displays are very inexpensive (under $2.00 with shipping) and
provide a lot of help when trying to debug complicated code.

* Try to keep Makefile up to date.
 2017-08-25 17:03:07 -05:00
GMagician
0067bb2840 Addressing #7552 
When M405 is used it changes 'volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM]' value. When M406 disables M405 it leaves the value unchanged.
This PR applies 'calculate_volumetric_multipliers' in M406 instead of resetting it to 1.0 because M200 may not be compatible with M405 hence I'm sure to restore anyway with correct value.
 2017-08-25 03:23:16 -05:00
Scott Lahteine
2b12093589 Merge pull request #7532 from thinkyhead/bf1_fan_mux_vben 
New feature: Part-Cooling Fan Multiplexer
 2017-08-25 03:16:40 -05:00
Michal Holes
54d48130f3 Slovak UTF-8 translation 
Slovak UTF-8 translation
 2017-08-23 19:14:35 -05:00
Scott Lahteine
86c024ce98 Organize, document pins.h include lines 2017-08-23 18:33:00 -05:00
Scott Lahteine
c7b07d20f2 Minor patches to pins files 2017-08-23 18:32:59 -05:00
Scott Lahteine
356af7dcb0 Tweak Sanguinololu-related pins files 2017-08-23 18:32:59 -05:00
Scott Lahteine
11a724d8fc Sanguinololu example configuration 2017-08-23 18:32:59 -05:00
Scott Lahteine
e337df2e98 Miscellaneous tweaks to serial outputs, code cleanups 2017-08-23 18:32:58 -05:00
Vben
c0409b85e7 New feature: Part-Cooling Fan Multiplexer 2017-08-18 15:59:04 -05:00
Scott Lahteine
e82e9073d6 Merge pull request #7530 from GMagician/Code-reduction 
Code reduction with some configurations
 2017-08-18 13:57:59 -05:00
GMagician
6127154af3 Fix identation by tab 
There was a tab instead of spaces
 2017-08-18 11:34:55 +02:00
GMagician
b94a1c6b9f Code reduction this some configurations 
When switching noozle and extruder but these operations are done by the same servo in 'setup' function there is a unnecessary call
 2017-08-18 11:11:00 +02:00
GMagician
405a2132f3 #7529 compile fix 
I made an error in previous fix
 2017-08-17 22:04:28 +02:00
GMagician
869d7f3703 #7504 missing part 
#7504 integration has missed this part.
When more than 1 servo is used with bltouch it's impossible to predefine default servo delay for it.
In my original fix I completely removed this part but maybe this is a better compromise
 2017-08-17 21:43:47 +02:00
Scott Lahteine
101ba70517 Merge pull request #7505 from thinkyhead/bf1_anet_1_pio 
Add Anet 1.0 to Platformio.ini
 2017-08-17 00:33:20 -05:00
Vben
4817b39d98 Added new feature for AutoParking Extruder (APE) 2017-08-16 17:33:11 -05:00
Scott Lahteine
6772e33ef6 Use [XY]_CENTER for error correction 
Followup to #7512
 2017-08-16 16:13:09 -05:00
Scott Lahteine
385f1bb9e5 Merge pull request #7504 from thinkyhead/bf1_servo_delays 
Individual servo delays
 2017-08-16 16:05:22 -05:00
Scott Lahteine
2a31c9f2ce Merge pull request #7515 from cdedwards/bugfix-1.1.x 
Fix for G26 spam output
 2017-08-16 16:01:10 -05:00
MTrab
5fa61c0ad3 Add Anet 1.0 to Platformio.ini 
Added env:anet10 to platformio.ini for easy compile and upload to this board
 2017-08-16 15:59:20 -05:00