Commit Graph

378 Commits

Author SHA1 Message Date
Lenbok
0aa833fe6c Chamber temperature monitoring and auto fan control.
This is an initial cut for feedback.

Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?

Chamber temperatures are not reported on the LCD in any way.

When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.

As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
2018-04-06 23:09:44 -05:00
Scott Lahteine
dba26a6d1f Add Continuous Purge feature to Advanced Pause 2018-04-04 20:59:50 -05:00
Scott Lahteine
68b9503b96 MIN_PROBE_EDGE replaces DELTA_PROBEABLE_RADIUS 2018-03-19 02:17:45 -05:00
Scott Lahteine
7b2ea8febe Sync main adv config with recent change 2018-03-15 00:09:23 -05:00
Scott Lahteine
5c81ce2bb8
When STATUS_EXPIRE_SECONDS is 0, hide the position. (#10100)
Some users may prefer to hide the position updates on the `LIGHTWEIGHT_UI` altogether. This leads to an even less cluttered display (it also saves on SPI traffic and one byte of RAM).
2018-03-14 02:44:41 -05:00
Studiodyne
7f8984b500 [1.1] FWRetract Reset (Best way) (#10084) 2018-03-14 01:34:15 -05:00
Scott Lahteine
738a8495ad Improve TMC config organization, naming 2018-03-13 21:43:43 -05:00
Scott Lahteine
a9392c6b27 Set a safe default MINIMUM_STEPPER_PULSE of 2 2018-03-09 03:59:18 -06:00
Scott Lahteine
2d0d5eccd8 Move AUTO_REPORT_SD_STATUS to SDSUPPORT block 2018-03-07 01:58:31 -06:00
Scott Lahteine
fb9de6e787 Add AUTO_REPORT_SD_STATUS feature
For parity with 2.0.x ahead of 1.1.9 release.
2018-03-07 00:06:03 -06:00
Studiodyne
d25f0a5a21 Fix for Fwretract bugfix1.1.x (#9872) 2018-03-01 02:59:42 -06:00
Scott Lahteine
6845f17fb2 Prettify LCD_PROGRESS_BAR options 2018-02-23 19:13:03 -06:00
Scott Lahteine
03da273ea6 Fix LCD_PROGRESS bar
Fix #9208
2018-02-23 13:59:55 -06:00
Sebastianv650
9c65890644 [1.1.x] LIN_ADVANCE v1.5 (#9700) 2018-02-23 00:53:41 -06:00
Scott Lahteine
1c95c13224 Lightweight status screen for ST7920
- This status screen uses the ST7920 character generator to greatly reduce SPI traffic and MCU load when updating the status screen.

- Has been tested with the RepRapDiscount Full Graphics Smart Controller but should work with any LCD that uses an ST7920 or fully compatible controller.
2018-02-22 00:46:25 -06:00
Scott Lahteine
855b188102
Hephestos2 heated bed kit for all (#9756) 2018-02-21 22:26:56 -06:00
Scott Lahteine
2e5a6243df Option to force X or Y to home first when homing the other axis 2018-02-18 01:06:57 -06:00
Scott Lahteine
3a1fedaee6 Update LCD_SET_PROGRESS_MANUALLY in configs 2018-02-17 15:41:20 -06:00
Bob-the-Kuhn
1647db8fad Set CONTROLLER_FAN_PIN example to -1 2018-02-15 21:29:09 -06:00
Scott Lahteine
d89a61bd51 Update DIGIPOT_I2C_MOTOR_CURRENTS comments 2018-02-13 22:56:03 -06:00
Scott Lahteine
4f04f4e6b8 Followup to #9532 2018-02-08 03:39:20 -06:00
jaysonkelly
f8a8711075 I2C position encoders update
Updating I2C position encoders to enable babystepping and Babystep XY when using the ecm microstep correction method. Also changed default method to ECM microstep.
2018-02-08 02:46:12 -06:00
Scott Lahteine
8438a57910 Followup to #9532 2018-02-08 02:05:18 -06:00
Thomas Moore
a471cd26e1 [1.1.x] Enable Z axis and delta sensorless homing (#9532) 2018-02-08 02:02:48 -06:00
Manuel Valentino
652162777b [1.1.x] Fixed wrong information about TMC2208 wiring (#9334) 2018-02-02 04:14:43 -06:00
teemuatlut
923f17328f Add TMC software SPI (#9362) 2018-02-02 03:56:08 -06:00
nhchiu
4a40cf268d Use NEOPIXEL as case light
Add an option to use the NEOPIXEL LED as case light.
2018-01-20 16:57:04 -06:00
Scott Lahteine
8f08e029d8 More up-front option to show SD percentage 2018-01-14 23:30:59 -06:00
Scott Lahteine
d1ce0bc071 M915 Z Axis Calibration 2018-01-09 18:55:08 -06:00
Scott Lahteine
8e82dd0b5b
Merge pull request #8947 from houseofbugs/bugfix-1.1.x
[1.1.x] SLIM_LCD_MENUS option
2017-12-31 00:56:10 -06:00
houseofbugs
a66811a597 A specific option to SLIM_LCD_MENUS 2017-12-31 00:15:24 -06:00
Scott Lahteine
839dd66c3b Synchronize configs with 2.0.x 2017-12-31 00:02:22 -06:00
Thomas Moore
81193e9338 Add M701 / M702 filament load / unload 2017-12-30 19:48:21 -06:00
silentninja1
b12eb33feb Add support for pause and resume action commands on M600 2017-12-25 01:28:17 -06:00
Thomas Moore
59d047c1d7 [1.1.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE (#8864)
* Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE
2017-12-24 23:47:05 -06:00
Scott Lahteine
ab7f1a0608 A single setting to validate filament width 2017-12-19 21:34:30 -06:00
Scott Lahteine
435981056e Option to disable all volumetric extrusion 2017-12-19 20:33:41 -06:00
robpower
59265034ae Extended NanoDLP_Z_Move_Sync feature to G4 and G28, Added optional move_sync for all axis. 2017-12-15 16:05:29 -06:00
teemuatlut
0ac0324af2 [1.1.x] TMC driver update (#8712) 2017-12-15 15:02:39 -06:00
Scott Lahteine
44800e9899 PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING 2017-12-07 16:46:06 -06:00
Scott Lahteine
1f770bb103 Config updates, spacing mainly 2017-11-29 20:57:38 -06:00
Tannoo
e25567a5dd New feature: LED_CONTROL_MENU 2017-11-29 20:57:38 -06:00
Scott Lahteine
fd50f452ff Whitespace cleanup 2017-11-28 17:49:25 -06:00
Scott Lahteine
51d09bb9c9 Tweak BLOCK_BUFFER_SIZE config 2017-11-26 17:33:33 -06:00
Scott Lahteine
c0190eff00 Adapt MESH_EDIT_GFX_OVERLAY for 1.1.x 2017-11-24 15:54:02 -06:00
Rob Power
f8e30f49d7 Add NanoDLP Z movement synchronization option
Implemented synchronization message output for NanoDLP printers (nanodlp.com).
If optional feature is enabled in `Configuration_adv.h`, Marlin will ouput "Z_move_comp" string to serial after completing any G0/G1 Z-axis movements. This feature patched on previous versions(1.0) is used by NanoDLP to synchronize Z-axis movement with projector exposure in DLP stereolithography printers.
2017-11-24 00:32:03 -06:00
Scott Lahteine
8d06cf7b84 Add M114_DETAIL to Configuration_adv.h 2017-11-14 00:06:35 -06:00
Scott Lahteine
069ec3f9a9 Move Filament Width Sensor to Configuration_adv.h 2017-11-13 21:06:40 -06:00
Rowan Meara
094bebcc2d [1.1.x] Update Thermal Protection Documentation (#8282)
* Fix thermal protection documentation.

Even before the recent thermal protection changes, the documentation of
the thermal protection feature in the config files did not match the
implementation.  I fixed the documentation and reconciled the M303
implementation with the documentation.

* Applied documentation changes to sample config files

* Renamed hysteresis to watch_temp_increase

* Added gcodes back into documentation.
2017-11-07 15:52:28 -06:00
Scott Lahteine
bb111b928b Add CNC_COORDINATE_SYSTEMS to configs 2017-11-04 22:30:23 -05:00