Commit Graph

9647 Commits

Author SHA1 Message Date
indazoo
f6bf247302 Add RepRapPro Huxley configuration (#10343) 2018-04-08 00:19:40 -05:00
Scott Lahteine
8e35029f10
Merge pull request #9789 from Lenbok/monitor_chamber_temperature_and_auto_fan
[1.1.x] Monitor chamber temperature, with auto chamber fan control.
2018-04-06 23:52:06 -05:00
Lenbok
0aa833fe6c Chamber temperature monitoring and auto fan control.
This is an initial cut for feedback.

Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?

Chamber temperatures are not reported on the LCD in any way.

When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.

As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
2018-04-06 23:09:44 -05:00
Scott Lahteine
08b09f7a4c Add Chamber Temp options to example configs 2018-04-06 23:09:43 -05:00
Roman Moravčík
151962baf2 Update Slovak language (#10313) 2018-04-06 20:20:40 -05:00
Bob-the-Kuhn
aca2bbbc50 Add TMC software SPI pins to pinsDebug_list.h (#10325) 2018-04-06 20:16:05 -05:00
Scott Lahteine
211544b543 Reset progress bar when print ends
Fix #10330
Based on #10333 by @marcio-ao
2018-04-06 20:12:40 -05:00
GMagician
8e36d00ad0 [1.1.x] Update language_it.h (#10323)
Updated to #10296
2018-04-06 20:07:08 -05:00
Scott Lahteine
e596931aac
Merge pull request #10321 from thinkyhead/bf1_einsy_retro_etc
[1.1.x] Fix TMC2130 DIAG1 active high, Einsy Retro
2018-04-06 00:30:50 -05:00
Scott Lahteine
ed949cc5c1 Added support for Einsy Retro
http://reprap.org/wiki/EinsyRetro
2018-04-05 18:15:58 -05:00
Scott Lahteine
53757444c5 Default active low for TMC2130 DIAG1 (#10294)
- Added sanity check to require endstop inverting with SENSORLESS_HOMING
2018-04-05 18:15:58 -05:00
Scott Lahteine
c46d47f45f Scale feedrate (mm/s to deg/s) for SCARA 2018-04-05 16:17:23 -05:00
Anton Piliugin
bc2fc86993 Update language_ru.h (#10311) 2018-04-05 00:47:02 -05:00
Scott Lahteine
01e100360f
Merge pull request #10176 from noingwhat/1.1.x-Continuous-Purge
[1.1.x] Continuous Purge
2018-04-04 22:50:37 -05:00
Scott Lahteine
dba26a6d1f Add Continuous Purge feature to Advanced Pause 2018-04-04 20:59:50 -05:00
Scott Lahteine
05fc3d7891 Add ADVANCED_PAUSE_CONTINUOUS_PURGE to example configs 2018-04-04 20:53:00 -05:00
Scott Lahteine
7ff70d7adb
Improve heating/cooling LCD messages (#10296) 2018-04-04 19:13:48 -05:00
Scott Lahteine
a7e142460c
MBL should add z_offset regardless of fade (#10307) 2018-04-04 18:27:09 -05:00
GMagician
9d2ef95f1d Additional tool-change fix (#10305)
Followup to #10243
2018-04-04 17:06:25 -05:00
Pavel Peganov
de5f69b285 Add Creality CR-8 configuration (#10285) 2018-04-02 19:58:02 -05:00
Scott Lahteine
829281d016
Merge pull request #10243 from thinkyhead/bf1_tool_change_debug 2018-04-02 19:33:27 -05:00
Scott Lahteine
be098cd42f Z Endstop Servo => Z Probe Servo 2018-04-01 23:54:47 -05:00
Scott Lahteine
2dafc10da3
Merge pull request #10271 from D-side/ender-4-board-id
[1.1.x] Fix Ender 4 compilation, add more AVRs to Makefile
2018-04-01 18:25:35 -05:00
Scott Lahteine
6444ef02e4 Add remaining boards to Makefile 2018-04-01 18:15:52 -05:00
D-side
ab5232c37b Fix Ender 4 / CR-8 compilation
- Assign 243 (like EFB) as Ender-4/CR-8 board ID
- Add to `Makefile`
- Add to `pins.h`
2018-04-01 18:15:52 -05:00
MoellerDi
6b150bfc40 Handle disabled HYBRID_THRESHOLD in EEPROM (#10274) 2018-04-01 16:58:30 -05:00
Scott Lahteine
885ad70c8b Fix likely issue with retract/recover
Addressing #10200
2018-03-31 22:59:48 -05:00
Scott Lahteine
d37cfa327e Note about MKS_MINI_12864 in sanitycheck 2018-03-31 22:51:43 -05:00
Scott Lahteine
040ebd1675 Use lcd_printPGM_utf in more places
Fix #10256
2018-03-31 20:47:20 -05:00
Scott Lahteine
48fa0e6de0 Output ABC for delta stepper counts 2018-03-31 20:12:53 -05:00
Scott Lahteine
c9aa7486ce Use float62 for LCD edit of Z Fade 2018-03-31 20:02:28 -05:00
Scott Lahteine
80b3f8c395 Allow Z_SAFE_HOMING sanity checks to handle floats 2018-03-31 19:00:14 -05:00
Scott Lahteine
712b213b40 Split up tool_change, raise for non-delta too 2018-03-30 16:06:52 -05:00
Scott Lahteine
52750bf362 Simplified leveling-based tool change 2018-03-30 16:06:47 -05:00
Scott Lahteine
0afdec882c For set_z_fade_height use set_bed_leveling_enabled 2018-03-30 16:06:42 -05:00
Scott Lahteine
29b048810c Symmetrical FWRETRACT Z Hop
Do the Z lift normally before setting Z back to its prior value. But do the Z lower using spoofing. This should produce proper symmetrical movement.
2018-03-30 15:47:06 -05:00
Scott Lahteine
0eb1830d85 Change order of inactive stepper disable/enable
This ensures that steppers that share an enable pin will only be disabled for a miniscule time.
2018-03-30 15:10:03 -05:00
Scott Lahteine
f5c980f9cf Clear the "Wait for user" message set by M0/M1
See https://github.com/MarlinFirmware/Marlin/issues/10246#issuecomment-377146936
2018-03-29 17:57:50 -05:00
Scott Lahteine
d36e950547 Temporary workaround for tool-change compile error
Pending a more complete solution to tool-change Z deviation.
2018-03-29 17:57:50 -05:00
Scott Lahteine
df75e9d692 Fix BLTOUCH compile error
Followup to #10249
2018-03-29 17:57:49 -05:00
AnHardt
86c3be7089 No delay in sensorless quick homing (#10253) 2018-03-29 16:09:19 -05:00
Scott Lahteine
575b099e40 Alert users about low Z jerk values 2018-03-28 22:58:41 -05:00
Scott Lahteine
360166f626
Merge pull request #10249 from thinkyhead/bf1_homing_move_adjustments
[1.1.x] Improvements to general and delta homing
2018-03-28 22:05:40 -05:00
Scott Lahteine
b5f1a4141c "G28 Z forbidden" => "Home XY first" 2018-03-28 21:54:20 -05:00
Scott Lahteine
0401f4ce14 Clear sensorless homing in home_delta after first move-to-top 2018-03-28 21:19:14 -05:00
Scott Lahteine
9f3b4d537d Do moves towards endstops differently in do_homing_move 2018-03-28 21:19:14 -05:00
Scott Lahteine
deefd2defa
Wait before turning off PRINTER_EVENT_LEDS at print end (#10247) 2018-03-28 20:32:32 -05:00
Scott Lahteine
1e31b56b0f Fix checksum + card.saving
Followup to #10204
2018-03-28 18:40:36 -05:00
Scott Lahteine
86e58df324 Fix G10/G11 debug logging 2018-03-28 18:40:36 -05:00
Scott Lahteine
3edf9904f4 Fix linear/3-point manual leveling buffer overrun
Fixes #10137
2018-03-28 18:40:36 -05:00