MPCNC/Firmware2
1
0
Fork 0
Code Issues 1 Pull Requests Releases Wiki Activity
2,495 Commits 1 Branch 0 Tags 129 MiB
1fac388664
Commit Graph

369 Commits

Author SHA1 Message Date
daid
53f971095d Revert "Reduce PROGMEM warnings" 2015-01-16 16:48:22 +01:00
Bo Herrmannsen
5151db5c2f Merge pull request #1349 from msutas/patch-2 
Improvement - G29 Option for Not Retracting Servo
 2015-01-15 10:56:31 +01:00
Bo Herrmannsen
ab074dac17 Merge pull request #1344 from grob6000/independent_pid 
Independent PID parameters for each extruder
 2015-01-13 12:10:37 +01:00
Bo Herrmannsen
d4a665694a Merge pull request #1350 from odewdney/Development 
Reduce PROGMEM warnings
 2015-01-13 11:26:50 +01:00
msutas
3a5a6f42fb Corrected the ABL grid option 
G29 E was not retracting the probe on the last probe point when used with ABL grid. Corrected.
 2015-01-12 11:07:46 +02:00
odewdney
538859669d Removing compiler warnings for progmem 2015-01-11 18:14:21 +00:00
grob6000
bf2c923db5 Make multiple PID parameters a config option 
* Adds config parameter `PID_PARAMS_PER_EXTRUDER` - allows single PID
parameters to be used where this would be preferable (e.g. dual
identical extruders)
* When disabled, will use `float Kp, Ki, Kd, Kc;` as before.
Preprocessor macros used to switch between.
* ultralcd.cpp defines extra menus for extra parameters only where
required
* M301 reports `e:xx` only if independent pid parameters enabled
* EEPROM structure still leaves space for 3 extruders worth, when undef
will save single parameter to all extruder positions, but only read the
first
* Switching off saves approx 330 B with no LCD enabled, 2634B with LCD
(RRD) enabled: this is significant.
* LCD modifications should be tested.
 2015-01-11 13:50:17 +11:00
msutas
e0beb98fd3 Improvement - G29 Option for Not Retracting Servo 
This change introduces an improvement to G29 command on Marlin.

Auto bed leveling operation's reliability is based on the repeatability of the Z-probe switch and the servo. This change introduces an option to G29 command. When the G29 command is sent with an "e" option, during auto bed levelling the servo is not retracted between probes which decreases the bias on auto bed levelling resulting from servo.

G29 command does the auto bed probing as it is.

G29 E command engages the servo on first probing point, probes all points and retracts the servo after probing the last point.

Please comment your opinions, test on your printer and check the code on a programmer's perspective. (I am not a good programmer.)
 2015-01-10 17:25:39 +02:00
grob6000
37c7e8300f Independent PID parameters for each extruder 
* Variables Kp, Ki, Kd, Kc now arrays of size EXTRUDERS
* M301 gains (optional, default=0) E parameter to define which
extruder's settings to modify. Tested, works with Repetier Host's EEPROM
config window, albeit only reads/updates settings for E0.
* All Kp, Ki, Kd, Kc parameters saved in EEPROM (version now v14), up to
3 extruders supported (same as Marlin in general)
 2015-01-10 16:35:12 +11:00
Erik van der Zalm
1aade4a8e2 Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into Development 2015-01-09 21:33:29 +01:00
Erik van der Zalm
8a2e84e3f1 Possible fix for FWRETRACT with 0 zlift. 2015-01-09 21:33:02 +01:00
Erik van der Zalm
3a30d45c2e Revert "issue 968 for dev branch" 2015-01-07 23:40:17 +01:00
Dan Royer
9472bbe51d issue 968 for dev branch 
try, try again.

If 'OK' is garbled on sending PC won't receive it.  Both machines will
wait on each other forever.  This resends OK if nothing is heard from PC
for a while to avoid this bad case.
 2015-01-04 12:17:46 -08:00
Bo Herrmannsen
a18b625534 Merge pull request #1261 from wgm4321/Development 
Add Filament menu and add Filament/Retract settings to config store.
 2015-01-02 15:35:29 +01:00
bkubicek
d02daec08f fixed compilation 2014-12-30 08:04:06 +01:00
Bernhard Kubicek
f24c5d82e3 Update Marlin_main.cpp 
fixed minor typo
 2014-12-29 17:17:30 +01:00
Wurstnase
8a6f098cc6 Expand manage_inactivity #1264 
void manage_inactivity(bool ignore_stepper_queue=false)

standard is false so it is not necessary to change additional code. this
change should be better, hopefully nophead like this :)
 2014-12-29 17:07:22 +01:00
Wurstnase
d1995aec7a Rename ignore_blocks_queued 
more speaking name
 2014-12-29 16:47:08 +01:00
Wurstnase
4122de9d17 change filament issue 
make a more general solution
 2014-12-29 16:31:00 +01:00
wgm4321
cb12161191 Add Filament menu and add Filament/Retract settings to config store. 2014-12-28 20:43:14 -05:00
fmalpartida
ec33df0554 Merge branch 'SAV-MkI_merge' into Development 
Tested for SAV MKI and SAV 3D LCD on lewihe.
 2014-12-28 19:54:06 +01:00
alexborro
3afe66bb0c Fix issues #1248, #1240 
- Fixed issue when BAL area probing is shorter than it should be for
grid probing
- Warning when BAL activated with Delta Kinematics
- Fix XY_TRAVEL_SPEED when homing Z axis
 2014-12-28 13:27:39 -02:00
Lukas Obermann
9eb6df17a7 Consider negative Z Offsets when auto bed leveling is active 2014-12-28 12:46:35 +01:00
Denis Chertykov
050ca9ca13 Move initialization of errormagic[] and echomagic[] to Marlin_main.cpp 2014-12-28 09:09:42 +03:00
alexborro
d74aabf259 Revert "Change Auto_Bed_Leveling to Auto_Bed_Compensation" 2014-12-21 10:06:05 -02:00
Bo Herrmannsen
60628864ca Merge pull request #1167 from thinkyhead/sd_freemem 
Use SdFatUtil::FreeRam() for freeMemory() if there
 2014-12-20 18:31:21 +01:00
Bo Herrmannsen
889d7ba218 Merge pull request #1177 from martin-pr/probing_z_speed 
Split do_blocking_move() to XY and Z sections
 2014-12-20 18:30:35 +01:00
Bo Herrmannsen
5e7bd2dc87 Merge pull request #1200 from chertykov/Marlin_v1 
Fix syntax errors in #ifdef
 2014-12-20 18:29:39 +01:00
Denis Chertykov
b086394178 Fix syntax errors in #ifdef. 2014-12-20 19:33:43 +03:00
John Davis
4315c2547a Update Marlin_main.cpp 
Changed level and leveling to compensation (except with "verbose_level" and "lcd_reset_alert_level").
 2014-12-19 17:41:29 -05:00
Bo Herrmannsen
03e489aaad Merge pull request #1197 from foosel/fix/issue_1147 
Fixes commands not being acknowledged in the same order they are received in
 2014-12-19 14:39:05 +01:00
Gina Häußge
acc0e75279 Fixes commands not being acknowledged in the same order they are received 
in

G0 to G3 were previously acknowledged in the get_command method, causing
them to be possibly acknowledged before commands coming after them that
were acknowledged in process_commands.

This patch fixes this, moving the acknowledgement of G0 to G3 to the
process_commands method as well. These commands are therefore no
longer acknowledged when the enter the cmd_buffer but instead only
acknowledged when the enter the plan_buffer.

Guaranteeing that commands are acknowledged in the same order in which
they were received by the firmware allows host software to be able to
track the life cycle of commands and such a better management of the
firmware's serial buffers as well as better internal command processing
and response parsing without having to depend on throwing an epic
amount of regular expressions against each line received back from the
firmware.

Fixes ErikZalm/Marlin#1147
 2014-12-19 14:20:36 +01:00
Scott Lahteine
07c6b5ab71 Using axis constants 2014-12-18 08:13:08 -08:00
Scott Lahteine
0450e83fa5 Use SdFatUtil::FreeRam() for freeMemory() if there 2014-12-17 23:26:52 -08:00
Scott Lahteine
60598b4cdd A few constants where they belong 2014-12-17 23:01:24 -08:00
Martin Prazak
2ef0669b19 Split do_blocking_move() to XY and Z sections to make sure that the Z homing feedrate is not exceeded 2014-12-07 15:31:46 +00:00
Neil Darlow
64139f5e5a Merge https://github.com/ErikZalm/Marlin into Marlin_v1 2014-12-04 21:09:03 +00:00
Scott Lahteine
7562183efc Skip over spaces first 2014-11-28 08:09:28 -08:00
Scott Lahteine
12b51d6060 Ignore S and P if no value >0 is included. 2014-11-26 21:05:11 -08:00
Scott Lahteine
d12b24758a Clear LCD to welcome_msg if not printing 
The welcome message is more appropriate than “resuming print” if
nothing is printing.
 2014-11-26 21:05:11 -08:00
Scott Lahteine
92e21d3ee2 M0-M1 Enhancements 
Allow M0 and M1 to include a message string. Ignore clicks on “Wait for
user” so that the Info Screen stays up.
 2014-11-26 21:05:10 -08:00
Neil Darlow
b81021f475 Merge https://github.com/ErikZalm/Marlin into Marlin_v1 2014-10-21 12:06:56 +01:00
Erik van der Zalm
058e446531 Merge pull request #1037 from filipmu/Filament-Sensor 
Support for a filament diameter sensor
 2014-10-11 22:56:01 +02:00
Erik van der Zalm
b360306881 Merge pull request #1073 from WingTangWong/wing-fix-float-delta 
Wing fix float delta
 2014-10-06 13:41:01 +02:00
Scott Lahteine
f989bd5435 Simple code cleanup. Rename "homeing" to homing. 2014-10-05 13:20:53 -07:00
Neil Darlow
6c5a460e65 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-10-05 12:54:54 +01:00
galexander1
cb4a6dd2dc Merge pull request #1065 from oliasmage/Marlin_v1 
Corrected retract() call for use of auto probe without sled enabled.
 2014-09-19 15:12:09 -04:00
Bracken Dawson
01e9b536cb Fix build for non-sled bed auto levelling 
This function should only be used with sled, not all bed auto
levelling.
 2014-09-19 19:42:32 +01:00
Wing Tang Wong
58eabd21fb Added ifndef 2014-09-16 14:31:58 -07:00
Wing Tang Wong
88d12a762a Added #ifndef DELTA wrapper to float delta 2014-09-16 14:29:44 -07:00
Charles Bell
3b8216bdd1 Corrected #endif and ifdef for Z_PROBE_SLED code. 2014-09-04 16:40:22 -04:00
Charles Bell
37799f70ba Corrected retract() call for use of auto probe without sled enabled. 2014-09-04 14:36:39 -04:00
Neil Darlow
1632e5e38a Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-09-04 12:21:35 +01:00
Erik van der Zalm
018b68a5c4 Merge pull request #976 from cocktailyogi/SCARA_by_Yogi 
Implemented SCARA-Maths
 2014-08-28 16:32:52 +02:00
Erik van der Zalm
9887555192 Merge pull request #998 from darconeous/pull-requests/fwretract 
FWRETRACT fixes
 2014-08-28 16:24:51 +02:00
Erik van der Zalm
68dd5e635e Merge pull request #1024 from oliasmage/Marlin_v1 
Adding Z Probe via sled mounted endstop
 2014-08-28 16:15:54 +02:00
Erik van der Zalm
25069ed4e9 Merge pull request #1031 from Roxy-3DPrintBoard/Z_PROBE_REPEATABILITY-with-correct-Defaults 
Z probe repeatability with correct defaults
 2014-08-28 16:14:10 +02:00
Filip Mulier
62db9848d3 Improvements and bug fixes in sensor delay buffer for filament sensor code 
Improvement to avoid reinitializing delay buffer with every print. Fixed
issues in buffer indexing and memory out of bounds due to floating point
imprecision.  Simplified the code by avoiding conversion to standard
diameter and 1cu mm extrusion, which caused complications in determining
mm extruded.
 2014-08-16 06:50:13 -05:00
Florian Baumann
5908fd5cec Fix reseting CHDK pin to LOW 
chdkActive was set to false regardless of (millis() - chdkHigh) being bigger than the CHDK_DELAY or not. So if (millis() - chdkHigh) wasn't bigger than the delay the first time, the CHDK would never be set back to LOW.

Also, don't return from the function, as there might be other stuff to do, after the CHDK check.
 2014-08-11 14:12:32 +02:00
Roxy-3DPrintBoard
0091865583 Z_PROBE_REPEATABILITY test 
Z_PROBE_REPEATABILITY test for Auto Bed Leveling.
Implemented as M48 with extra user specified options.
Full support at
http://3dprintboard.com/showthread.php?2802-Auto_Bed_Leveling-Z-Probe-Repeatability-code
 2014-08-09 15:37:23 -05:00
Filip Mulier
85649a4549 Real-time filament diameter measurement and control 
This feature allows the printer to read the filament diameter
automatically and adjust the printer in real time.  Added code to read
an analog voltage that represents a filament diameter measurement.  This
measurement is delayed in a ring buffer to compensate for sensors that
are a distance away from the extruder.  The measurement is used to
adjust the volumetric_multiplier for the extruder.  Some additional g
codes (M404, M405, M406, M407) are used to set parameters and turn
on/off the control. g code M221 is updated.  Pins for RAMPS1.4, RAMBO,
and Printrboard are identified for analog input.  The configuration file
is updated with relevant user parameters.
 2014-08-06 19:30:57 -05:00
Charles Bell
d2fcb3ee56 CAB: Added code for Z-probe with Z endstop mounted on a sled. 2014-08-01 11:29:59 -04:00
Neil Darlow
3cd7dbcc45 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-07-30 13:01:52 +01:00
daid
c13a831ea1 Merge pull request #1017 from foosel/fix/checksum_truncation_bug 
Fix for a wrong checksum truncation for certain commands
 2014-07-24 19:41:34 +02:00
Gina Häußge
2d22902d08 Fix for a wrong checksum truncation for certain commands 
Positioning of string terminator to truncate checksum from the commands
M23, M28, M30, M32, M928 and M117 was off by one, causing the last
letter of the actual command to be truncated instead of just the
checksum.

In case of the SD commands this caused checksummed commands targeting
existing files to fail since the last letter of the filename was
truncated.

In case of M117 this caused the last given letter not to be displayed.

This patch fixes the off-by-one error and sets the null terminator
on the exact position of the * starting the checksum instead of the
character before that.
 2014-07-24 12:04:02 +02:00
cocktailyogi
2f4a20257c imported last Marlin changes 2014-07-20 13:49:26 +02:00
daid
aacff0d361 Merge pull request #948 from Dim3nsioneer/Marlin_v1 
Implementation of FW extruder change retract
 2014-07-18 16:10:15 +02:00
Robert Quattlebaum
1fd9a7d476 Fix for FWRETRACT on DELTA printers. 
Fixes #817
 2014-07-09 09:24:26 -07:00
Neil Darlow
3f2c771d90 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-07-07 18:17:15 +01:00
Pablo Clemente
2242a84218 Changed the declaration of the variable to Marlin_main.cpp to fix issue on commit #965 2014-07-01 16:45:03 +02:00
Neil Darlow
6e3406d228 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-07-01 10:27:39 +01:00
Pablo Clemente
d86c3cf43c Changed the type of variable to bool, the name to "cancel_heatup", flags implementation and added this fix to M190 gcode too. 2014-06-30 15:12:13 +02:00
cocktailyogi
f0cab611db optimised some math-code 2014-06-24 18:43:36 +02:00
cocktailyogi
fae7d08698 fixed wrong compiler-option 2014-06-23 18:16:42 +02:00
cocktailyogi
512f2a3136 restore Branch from Backup 
sorry for that
 2014-06-23 17:09:57 +02:00
Pablo Clemente
cd3220d055 Inverted state logic for forced_heating_stop variable 2014-06-13 08:39:58 +02:00
Pablo Clemente
86b4b805d2 Fixed stop print LCD function on M104 2014-06-12 18:43:16 +02:00
Dim3nsioneer
3c927901a4 Implementation of FW extruder change retract 
FW retraction is extended onto swap retraction invoked by 'G10 S1'.
Bookkeeping of the retract state of all extruders allows for having one
extruder fw standard retracted while another extruder is swap retracted.
An LCD menu item for the swap retract and recover length was added.
 2014-06-02 17:02:10 +02:00
neildarlow
efb6d61413 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-05-24 13:08:58 +01:00
nothinman
38192cb5f3 Add M112 description to Marlin_main 2014-05-20 15:20:19 +01:00
nothinman
aed5ec008a Merge pull request #851 from DanNixon/estop 
Implemented M112
 2014-05-19 17:55:34 +01:00
Erik van der Zalm
cfb98ef682 More coverity fixes 2014-05-15 22:09:50 +02:00
Erik van der Zalm
9db9842aea Fixed error found by the free coverity tool (https://scan.coverity.com/) 
===================================================
Hi,

Please find the latest report on new defect(s) introduced to ErikZalm/Marlin found with Coverity Scan.

Defect(s) Reported-by: Coverity Scan
Showing 15 of 15 defect(s)

** CID 59629:  Unchecked return value  (CHECKED_RETURN)
/Marlin_main.cpp: 2154 in process_commands()()

** CID 59630:  Operands don't affect result  (CONSTANT_EXPRESSION_RESULT)
/Applications/Arduino.app/Contents/Resources/Java/hardware/arduino/cores/arduino/Tone.cpp: 319 in tone(unsigned char, unsigned int, unsigned long)()

** CID 59631:  Missing break in switch  (MISSING_BREAK)
/Marlin_main.cpp: 1187 in process_commands()()

** CID 59632:  Missing break in switch  (MISSING_BREAK)
/Marlin_main.cpp: 1193 in process_commands()()

** CID 59633:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 914 in disable_heater()()

** CID 59634:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 913 in disable_heater()()

** CID 59635:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 626 in analog2temp(int, unsigned char)()

** CID 59636:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 620 in analog2temp(int, unsigned char)()

** CID 59637:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 202 in PID_autotune(float, int, int)()

** CID 59638:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 214 in PID_autotune(float, int, int)()

** CID 59639:  Out-of-bounds write  (OVERRUN)
/Marlin_main.cpp: 2278 in process_commands()()

** CID 59640:  Out-of-bounds read  (OVERRUN)
/Marlin_main.cpp: 1802 in process_commands()()

** CID 59641:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 51 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()

** CID 59642:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 45 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()

** CID 59643:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 32 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()

________________________________________________________________________________________________________
*** CID 59629:  Unchecked return value  (CHECKED_RETURN)
/Marlin_main.cpp: 2154 in process_commands()()
2148                 }
2149               #endif
2150             }
2151           }
2152           break;
2153         case 85: // M85
   CID 59629:  Unchecked return value  (CHECKED_RETURN)
   Calling "code_seen" without checking return value (as is done elsewhere 66 out of 67 times).
2154           code_seen('S');
2155           max_inactive_time = code_value() * 1000;
2156           break;
2157         case 92: // M92
2158           for(int8_t i=0; i < NUM_AXIS; i++)
2159           {

________________________________________________________________________________________________________
*** CID 59630:  Operands don't affect result  (CONSTANT_EXPRESSION_RESULT)
/Applications/Arduino.app/Contents/Resources/Java/hardware/arduino/cores/arduino/Tone.cpp: 319 in tone(unsigned char, unsigned int, unsigned long)()
313         else
314         {
315           // two choices for the 16 bit timers: ck/1 or ck/64
316           ocr = F_CPU / frequency / 2 - 1;
317
318           prescalarbits = 0b001;
   CID 59630:  Operands don't affect result  (CONSTANT_EXPRESSION_RESULT)
   "ocr > 65535U" is always false regardless of the values of its operands. This occurs as the logical operand of if.
319           if (ocr > 0xffff)
320           {
321             ocr = F_CPU / frequency / 2 / 64 - 1;
322             prescalarbits = 0b011;
323           }
324

________________________________________________________________________________________________________
*** CID 59631:  Missing break in switch  (MISSING_BREAK)
/Marlin_main.cpp: 1187 in process_commands()()
1181         case 2: // G2  - CW ARC
1182           if(Stopped == false) {
1183             get_arc_coordinates();
1184             prepare_arc_move(true);
1185             return;
1186           }
   CID 59631:  Missing break in switch  (MISSING_BREAK)
   The above case falls through to this one.
1187         case 3: // G3  - CCW ARC
1188           if(Stopped == false) {
1189             get_arc_coordinates();
1190             prepare_arc_move(false);
1191             return;
1192           }

________________________________________________________________________________________________________
*** CID 59632:  Missing break in switch  (MISSING_BREAK)
/Marlin_main.cpp: 1193 in process_commands()()
1187         case 3: // G3  - CCW ARC
1188           if(Stopped == false) {
1189             get_arc_coordinates();
1190             prepare_arc_move(false);
1191             return;
1192           }
   CID 59632:  Missing break in switch  (MISSING_BREAK)
   The above case falls through to this one.
1193         case 4: // G4 dwell
1194           LCD_MESSAGEPGM(MSG_DWELL);
1195           codenum = 0;
1196           if(code_seen('P')) codenum = code_value(); // milliseconds to wait
1197           if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait
1198

________________________________________________________________________________________________________
*** CID 59633:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 914 in disable_heater()()
908          WRITE(HEATER_0_PIN,LOW);
909        #endif
910       #endif
911
912       #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1
913         target_temperature[1]=0;
   CID 59633:  Out-of-bounds write  (OVERRUN)
   Overrunning array "soft_pwm" of 1 bytes at byte offset 1 using index "1".
914         soft_pwm[1]=0;
915         #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1
916           WRITE(HEATER_1_PIN,LOW);
917         #endif
918       #endif
919

________________________________________________________________________________________________________
*** CID 59634:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 913 in disable_heater()()
907        #if defined(HEATER_0_PIN) && HEATER_0_PIN > -1
908          WRITE(HEATER_0_PIN,LOW);
909        #endif
910       #endif
911
912       #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1
   CID 59634:  Out-of-bounds write  (OVERRUN)
   Overrunning array "target_temperature" of 1 2-byte elements at element index 1 (byte offset 2) using index "1".
913         target_temperature[1]=0;
914         soft_pwm[1]=0;
915         #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1
916           WRITE(HEATER_1_PIN,LOW);
917         #endif
918       #endif

________________________________________________________________________________________________________
*** CID 59635:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 626 in analog2temp(int, unsigned char)()
620       if(heater_ttbl_map[e] != NULL)
621       {
622         float celsius = 0;
623         uint8_t i;
624         short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
625
   CID 59635:  Out-of-bounds read  (OVERRUN)
   Overrunning array "heater_ttbllen_map" of 1 bytes at byte offset 1 using index "e" (which evaluates to 1).
626         for (i=1; i<heater_ttbllen_map[e]; i++)
627         {
628           if (PGM_RD_W((*tt)[i][0]) > raw)
629           {
630             celsius = PGM_RD_W((*tt)[i-1][1]) +
631               (raw - PGM_RD_W((*tt)[i-1][0])) *

________________________________________________________________________________________________________
*** CID 59636:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 620 in analog2temp(int, unsigned char)()
614         if (e == 0)
615         {
616           return 0.25 * raw;
617         }
618       #endif
619
   CID 59636:  Out-of-bounds read  (OVERRUN)
   Overrunning array "heater_ttbl_map" of 1 2-byte elements at element index 1 (byte offset 2) using index "e" (which evaluates to 1).
620       if(heater_ttbl_map[e] != NULL)
621       {
622         float celsius = 0;
623         uint8_t i;
624         short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
625

________________________________________________________________________________________________________
*** CID 59637:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 202 in PID_autotune(float, int, int)()
196       {
197          soft_pwm_bed = (MAX_BED_POWER)/2;
198          bias = d = (MAX_BED_POWER)/2;
199        }
200        else
201        {
   CID 59637:  Out-of-bounds write  (OVERRUN)
   Overrunning array "soft_pwm" of 1 bytes at byte offset 1 using index "extruder" (which evaluates to 1).
202          soft_pwm[extruder] = (PID_MAX)/2;
203          bias = d = (PID_MAX)/2;
204       }
205
206
207

________________________________________________________________________________________________________
*** CID 59638:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 214 in PID_autotune(float, int, int)()
208
209      for(;;) {
210
211         if(temp_meas_ready == true) { // temp sample ready
212           updateTemperaturesFromRawValues();
213
   CID 59638:  Out-of-bounds read  (OVERRUN)
   Overrunning array "current_temperature" of 1 4-byte elements at element index 1 (byte offset 4) using index "extruder" (which evaluates to 1).
214           input = (extruder<0)?current_temperature_bed:current_temperature[extruder];
215
216           max=max(max,input);
217           min=min(min,input);
218           if(heating == true && input > temp) {
219             if(millis() - t2 > 5000) {

________________________________________________________________________________________________________
*** CID 59639:  Out-of-bounds write  (OVERRUN)
/Marlin_main.cpp: 2278 in process_commands()()
2272               tmp_extruder = code_value();
2273               if(tmp_extruder >= EXTRUDERS) {
2274                 SERIAL_ECHO_START;
2275                 SERIAL_ECHO(MSG_M200_INVALID_EXTRUDER);
2276               }
2277             }
   CID 59639:  Out-of-bounds write  (OVERRUN)
   Overrunning array "volumetric_multiplier" of 1 4-byte elements at element index 1 (byte offset 4) using index "tmp_extruder" (which evaluates to 1).
2278             volumetric_multiplier[tmp_extruder] = 1 / area;
2279           }
2280           break;
2281         case 201: // M201
2282           for(int8_t i=0; i < NUM_AXIS; i++)
2283           {

________________________________________________________________________________________________________
*** CID 59640:  Out-of-bounds read  (OVERRUN)
/Marlin_main.cpp: 1802 in process_commands()()
1796             int pin_status = code_value();
1797             int pin_number = LED_PIN;
1798             if (code_seen('P') && pin_status >= 0 && pin_status <= 255)
1799               pin_number = code_value();
1800             for(int8_t i = 0; i < (int8_t)sizeof(sensitive_pins); i++)
1801             {
   CID 59640:  Out-of-bounds read  (OVERRUN)
   Overrunning array "sensitive_pins" of 28 2-byte elements at element index 55 (byte offset 110) using index "i" (which evaluates to 55).
1802               if (sensitive_pins[i] == pin_number)
1803               {
1804                 pin_number = -1;
1805                 break;
1806               }
1807             }

________________________________________________________________________________________________________
*** CID 59641:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 51 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
45     }
46
47     LiquidCrystal::LiquidCrystal(uint8_t rs,  uint8_t enable,
48     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
49     {
50       init(1, rs, 255, enable, d0, d1, d2, d3, 0, 0, 0, 0);
   CID 59641:  Uninitialized scalar field  (UNINIT_CTOR)
   Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
51     }
52
53     void LiquidCrystal::init(uint8_t fourbitmode, uint8_t rs, uint8_t rw, uint8_t enable,
54     			 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
55     			 uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
56     {

________________________________________________________________________________________________________
*** CID 59642:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 45 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
39     }
40
41     LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable,
42     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
43     {
44       init(1, rs, rw, enable, d0, d1, d2, d3, 0, 0, 0, 0);
   CID 59642:  Uninitialized scalar field  (UNINIT_CTOR)
   Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
45     }
46
47     LiquidCrystal::LiquidCrystal(uint8_t rs,  uint8_t enable,
48     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
49     {
50       init(1, rs, 255, enable, d0, d1, d2, d3, 0, 0, 0, 0);

________________________________________________________________________________________________________
*** CID 59643:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 32 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
26
27     LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable,
28     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
29     			     uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
30     {
31       init(0, rs, rw, enable, d0, d1, d2, d3, d4, d5, d6, d7);
   CID 59643:  Uninitialized scalar field  (UNINIT_CTOR)
   Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
32     }
33
34     LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t enable,
35     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
36     			     uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
37     {

________________________________________________________________________________________________________
To view the defects in Coverity Scan visit, http://scan.coverity.com/projects/2224?tab=overview
 2014-05-14 21:59:48 +02:00
Neil Darlow
e541323741 Merge https://github.com/ErikZalm/Marlin into Marlin_v1 2014-05-09 15:02:50 +01:00
MyMakibox
21ec6b88c3 Update Marlin_main.cpp 
Added description of autotemp flags to M109
 2014-04-23 17:33:26 +08:00
Neil Darlow
6adbdf42e0 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-04-21 15:10:57 +01:00
whosawhatsis
27d544ac25 Speed up QUICK_HOME feedrate for diagonal move 
Speed up the diagonal move while still keeping each individual axis at
or below its homing feedrate.
 2014-04-19 17:29:20 -07:00
neildarlow
95ad6ec9a1 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-04-12 22:20:45 +01:00
Gabe Rosenhouse
27a7cf9fcf use existing strings 2014-04-07 05:01:48 -05:00
Gabe Rosenhouse
b0aeac117f Adjustable Z probe offset, via custom M-code 2014-04-06 19:45:56 -05:00
Neil Darlow
73b380d8d2 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-04-06 19:15:29 +01:00
nothinman
c23376f2e7 Merge pull request #837 from whosawhatsis/fwretract 
FWRETRACT in mm/s
 2014-04-04 11:47:58 +01:00
nothinman
9a5d23d96f Merge pull request #866 from sakunamary/Marlin_v1 
fix bug for dual extruders not working
 2014-04-02 18:27:42 +01:00
nothinman
303ee67896 Merge pull request #864 from whosawhatsis/M200 
fix bug in M200 with multiple extruders
 2014-04-02 18:26:15 +01:00
Tim
8759508319 fix bug for dual extruders not working 
some guy find that marlin not working good for dual extruders delta .
when type T0 or T1 to active extruder and  E0 or E1  move causing XYZ
motion . so i locales the bugs and fix it , I have dry run the fix.
 2014-04-01 09:26:19 +08:00
whosawhatsis
a65564eef6 fix bug in M200 with multiple extruders 2014-03-30 11:42:22 -07:00
whosawhatsis
aeaf9b9312 fix bug in M200 with multiple extruders 2014-03-30 11:41:57 -07:00
Dan Nixon
f643f4d674 Test and refactor 2014-03-21 20:42:00 +00:00
neildarlow
bbe8fbe13d Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-03-21 18:27:14 +00:00
Dim3nsioneer
3906f27c46 Individual extruder flow rate 
Extension of M221, Tune menu
 2014-03-15 18:09:46 +01:00
Dan Nixon
a38c90ee84 Added estop handling 2014-03-15 15:56:15 +00:00
Dan Nixon
272072fa20 Added M112 2014-03-14 23:19:43 +00:00
whosawhatsis
aab61e63c3 FWRETRACT in mm/s 
Firmware retraction now stores the retract and recover speeds in mm/s
instead of mm/min. This makes it match the units of the maximum
feedrate, and fixes problems with modifying the value via LCD control
panel. From gcode, the values are still taken in mm/min to match the
units of G1 and similar, and they are converted to mm/s before they are
stored.

I also lowered the default retract feedrate to make it less likely to
cause problems for geared extruders when the user hasn’t bothered to
set a reasonable maximum feedrate, though users should be setting both
of these values to suit their hardware.
 2014-03-14 15:17:28 -07:00
blddk
09af1b90b8 Added CHDK support 
Added CHDK support to take pictures instead of doing an IR command, see more about how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 2014-03-10 21:57:08 +01:00
neildarlow
7325d7102e Activate LiquidTWI2 device detection and space-pad LCD status line. 2014-03-03 21:01:27 +00:00
Jim Morris
8ea5665ee2 Merge remote-tracking branch 'origin/Marlin_v1' into add/M665-set-delta-configuration 
Conflicts:
	Marlin/Marlin_main.cpp
 2014-02-26 00:19:28 -08:00
Cylindric
fdce91192e Various typo fixes - only in comments, no code changes. 2014-02-25 10:01:15 +00:00
whosawhatsis
77df0d689a autretract fix 
I made these changes previously, but I can’t find the commit now. This
reapplies the changes to get auto retract working again.

Conflicts:
	Marlin/Configuration_adv.h
	Marlin/Marlin_main.cpp
 2014-02-24 13:24:38 -08:00
Gabe Rosenhouse
174b8d99d5 Simplify 3-point probing using new code only 2014-02-19 21:48:05 -08:00
Gabe Rosenhouse
3b718b816c better documentation 2014-02-19 14:04:37 -08:00
Gabe Rosenhouse
34fd59c370 ABL at any points 2014-02-19 13:18:21 -08:00
alexborro
9fa328e5c8 Merge pull request #793 from MissionSt/use_axis_enums 
Use constants instead of numeric literals
 2014-02-19 10:15:57 -03:00
Gabe Rosenhouse
f308a8af91 update comment 2014-02-19 01:06:24 -08:00
Gabe Rosenhouse
357e31270a Prevent G29 without first homing in X and Y 
If position is unknown, then G29 can be dangerous.
 2014-02-19 00:51:43 -08:00
Gabe Rosenhouse
d2d7d186b5 Use descriptive constants, more 2014-02-19 00:10:17 -08:00
Gabe Rosenhouse
2ccdf4f36d Use descriptive constants instead of numeric literals 2014-02-19 00:02:59 -08:00
daid
46bae30573 Merge pull request #776 from whosawhatsis/fwretract 
Fwretract fixes, cleanup
 2014-02-18 10:39:28 +01:00
Jim Morris
af9395ac2e Add M605 to dynamically set delta configuration 
Save above configs in eeprom
fix docs in createTemperatureLookupMarlin.py
add missing azteegX3pro digipot settings in delta example config
 2014-02-17 20:50:59 -08:00
nothinman
fd42f0d226 Merge pull request #783 from MissionSt/fix/syntax-error 
Fix compile error
 2014-02-17 20:59:43 +00:00
nothinman
96217bf36a Merge pull request #777 from PxT/M114 
Add whitespace to M114 output
 2014-02-17 18:07:47 +00:00
Gabe Rosenhouse
d1c64b9dc4 Fix syntax error introduced in 477b6fa1d 2014-02-17 07:56:19 -08:00
nothinman
d4ba23bc28 Merge pull request #770 from josefpavlik/Marlin_v1 
Marlin v1
 2014-02-17 11:27:05 +00:00
Paul Telford
306588925d Add whitespace to M114 output 2014-02-16 21:01:19 -08:00
whosawhatsis
c43838bb1e disable auto retract by default 
This should make it safe to enable FWRETRACT by default, with
autoretract (which should now be fixed) only enabled by M209. FWRETRACT
should probably now default to enabled (to make G10/G11 and M207-209
available, without changing functionality when they are not used), but
I’ll save that for another pull request/discussion.
 2014-02-16 19:04:54 -08:00
whosawhatsis
99f0e44864 Move FWRETRACT defaults to configuration_adv.h 2014-02-16 19:00:28 -08:00
whosawhatsis
66e3869138 Fix autoretract 
This takes the (now working) G10/G11 code and moves it to a function,
which is called by G10 and G11, and also called by G1 if autoretract is
enabled and a retract/recover move is detected.
 2014-02-16 18:59:04 -08:00
whosawhatsis
2f2459c0db Fix G10/G11 Z-lift 2014-02-16 18:15:34 -08:00
Gabe Rosenhouse
8c5675c290 Use language.h instead of English literals for "bed" 2014-02-16 17:16:00 -08:00
Gabe Rosenhouse
0f7393a13e Refactor 'accurate' auto bed leveling to use probe_pt() 2014-02-16 10:44:15 -08:00
Gabe Rosenhouse
c4fbb44d6d Refactor 3-point auto bed leveling to use probe_pt() 2014-02-16 10:44:08 -08:00
Gabe Rosenhouse
ad2c6488c7 Add probe_pt(), useful for auto bed leveling 2014-02-16 10:38:29 -08:00
Josef Pavlik
477b6fa1df move engaged from lcd console refreshes power off timeout 2014-02-14 12:37:21 +01:00
whosawhatsis
6e43398509 G10/G11 bugfixes 
Previous version was broken by using G92 E0 between retract and recover.
 2014-02-12 13:03:00 -08:00
whosawhatsis
d6c5c503d4 correct feedrate units in comments for M207/M208 2014-02-12 13:02:47 -08:00
whosawhatsis
b5ba5c1465 Merge branch 'Marlin_v1' of https://github.com/whosawhatsis/Marlin into Marlin_v1 2014-02-11 19:06:03 -08:00
whosawhatsis
78e7654601 Keep FWRETRACT values in terms of millimeters when using M200 
for volumetric E units
 2014-02-11 19:05:35 -08:00
whosawhatsis
3f6d44d40b Keep FWRETRACT values in terms of millimeters when using M200 for volumetric E units 2014-02-11 18:50:11 -08:00
Jim Morris
b819fc53ca Add Azteeg X3 Pro as motherboard 68 
Add digipot i2c control for MCP4451
Allow M907 to set i2c digipot currents in amps
Fix Makefile to allow Azteeg motherboards
Fix Makefile to allow Wire libraries only
Add beeper pin for Azteeg X3 Pro
 2014-02-05 01:47:12 -08:00
ErikZalm
e1ae7952eb Merge pull request #743 from Opticalworm/Marlin_v1 
Improved support for panelolu2 encoder and buzzer
 2014-02-03 12:33:10 -08:00
David Forrest
a5f53f0cf3 Heater wattage reporting for M105 using EXTRUDER_WATTS and BED_WATTS 2014-02-03 14:50:28 -05:00
Ronald
8d162e5bd7 Improved support for panelolu2 encoder and buzzer 
I added #define for LCD_FEEDBACK_FREQUENCY_HZ and
LCD_FEEDBACK_FREQUENCY_DURATION_MS  which is used to alter the default
buzzer sound.

When selecting Panelolu2 in configuration.h:
- it automatically sets the correct ENCODER_PULSES_PER_STEP and
ENCODER_STEPS_PER_MENU_ITEM.
- if LCD_USE_I2C_BUZZER is defined it will also set the default
LCD_FEEDBACK_FREQUENCY_HZ and LCD_FEEDBACK_FREQUENCY_DURATION_MS

When selecting the sanguinololu 1284p the following is true:
- its now enables  LARGE_FLASH
- It enables the gcode M300 when the panelolu2 LCD_USE_I2C_BUZZER is
defined
 2014-02-03 07:45:03 +00:00
whosawhatsis
b2c11ba980 Change diameter code to 'D' 
For some reason that I can’t figure out, the decimal is dropped when
using ’S’ for the code.

Also some minor code improvements to M200.
 2014-02-01 18:49:25 -08:00
whosawhatsis
856edfcc0d Fixed math 
This is why I wanted to sleep on the code I wrote while falling asleep
rather than immediately submitting a pull request.
 2014-01-31 08:43:11 -08:00
whosawhatsis
d24df7af2c M200 implementation 2014-01-31 00:54:19 -08:00
whosawhatsis
f08bb8bb6a Previous commit borked. 2014-01-19 22:06:45 -08:00
whosawhatsis
b1f8f492c6 Remove previous_millis_cmd update from extruder runout prevention code 
This seems to defeat the purpose of previous_millis_cmd, preventing the
time elapsed from previous_millis_cmd from ever reaching
max_inactive_time or stepper_inactive_time while the heat was on.
 2014-01-19 19:22:08 -08:00
whosawhatsis
8a5eaa3c9b Fix crash after home bug 
Fixes a bug in the Extruder Runout Prevention feature that caused the
extruder to move back to “current_position” after a move if it was
activated while the move was in progress. For long home moves (which
are longer than the dimensions of the machine’s working area), this
would cause the machine to crash into the far end of its travel after
homing. This usually occurred on the Z axis, which could result in
damage to the machine if you don’t hit the reset button in time.
 2014-01-19 19:11:51 -08:00
Alex Borro
05932e4458 Add Z Probe Offset to EEPROM and Ultra LCD 2014-01-16 18:13:46 -02:00
daid
380144c20f Add Ultiboard2 electronics. With PWM current settings. For the few people that have this new board as experiment in their UM-Original. 2014-01-06 11:05:02 +01:00
fsantini
6ae7f7870d Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into ErikZalm 
Conflicts:
	Marlin/Configuration.h
	Marlin/Marlin_main.cpp
 2013-12-23 12:20:32 +01:00