AnHardt
35af5ef23e
Merge pull request #2225 from Wurstnase/naming
...
consistency name for multiplier
2015-06-02 10:18:22 +02:00
wurstnase
e7e964432b
consistency name for multiplier
...
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
2015-06-01 22:33:22 +02:00
AnHardt
d4c6fc5d0a
Merge pull request #2223 from AnHardt/dualz-semicolon
...
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
2015-06-01 20:15:55 +02:00
AnHardt
0d9d21d15f
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
2015-06-01 19:51:43 +02:00
MagoKimbra
881146bc22
Fix problem Width Cura
2015-06-01 17:25:32 +02:00
fmalpartida
11e3f3375d
Merge commit '764e61708b8e73410c7819d59c4970d7089ca6f5' into bugFixing
...
Updated LCD wiki location.
2015-05-31 21:20:26 +02:00
Alexey Shvetsov
a8670b66a7
Update ru translation
...
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
2015-05-31 20:09:10 +03:00
fmalpartida
93da52d011
Added support for OLED SSD1306 I2C based LCDs.
2015-05-31 18:53:29 +02:00
Wurstnase
9c09967803
Merge pull request #2149 from Wurstnase/enstop_bits
...
faster compare
2015-05-31 16:02:55 +03:00
wurstnase
0f3f7d6835
clean up double endstops
2015-05-31 14:06:13 +02:00
AnHardt
9d2a980bcf
Merge pull request #2170 from thinkyhead/beep_M600_elsewise
...
Slight size reduction by adding idle()
2015-05-30 12:42:32 +02:00
AnHardt
2728dc0606
Merge pull request #2194 from thinkyhead/reduce_strings
...
Redo "invalid extruder" to save 304 bytes
2015-05-30 11:05:08 +02:00
Scott Lahteine
be5236e839
Reduce setTargetedHotend by removing the switch
2015-05-29 18:03:58 -07:00
Scott Lahteine
06f401e7e5
Redo "invalid extruder" to save 264 bytes
...
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
2015-05-28 22:25:28 -07:00
Scott Lahteine
1a882bcc2e
Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands
...
Ignore unknown commands if they start with G, M, or T
2015-05-28 22:03:48 -07:00
Scott Lahteine
a672872717
Merge pull request #2187 from AnHardt/MAX6675M105
...
Print active extruder with M105 for MAX6675
2015-05-28 18:12:48 -07:00
Scott Lahteine
9beed830eb
Drop commented code_is_good lines
2015-05-28 17:53:47 -07:00
Scott Lahteine
068d4a1eb2
Ignore unknown commands if they start with G, M, or T
2015-05-28 17:44:09 -07:00
Scott Lahteine
5824f613ff
Merge pull request #2185 from jothan/bed_integral
...
Separate the maximum integral power for the bed from PID_INTEGRAL_DRI…
2015-05-28 16:32:02 -07:00
Scott Lahteine
c5c9d12630
Merge pull request #2183 from AnHardt/displayinit
...
Initialize the display earlier
2015-05-28 16:29:18 -07:00
Scott Lahteine
ef4becc413
Merge pull request #2188 from AnHardt/FtoN
...
Replace MSG_F? with MSG_N?
2015-05-28 16:18:50 -07:00
Scott Lahteine
0564625757
Update M33 for new gcode parser
2015-05-28 14:17:39 -07:00
AnHardt
f18f689c01
Replace MSG_F? with MSG_N?
...
To avoid double definitions.
I prefer to read N for Number not for Nozzle.
2015-05-28 20:30:23 +02:00
AnHardt
af7e3f5076
Print active extruder with M105 for MAX6675
...
Was omitted when T0 is a MAX6675.
2015-05-28 19:03:16 +02:00
Jonathan Bastien-Filiatrault
d46d9d998e
Add maximum bed integral term in example configurations.
2015-05-28 12:51:37 -04:00
Jonathan Bastien-Filiatrault
e86f2342c0
Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
...
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
2015-05-28 11:48:04 -04:00
AnHardt
f0523b5816
Initialize the display earlier
...
to have it ready to display errors during (temperature)-setup.
2015-05-28 16:08:17 +02:00
Scott Lahteine
790c697c19
Fix DEGREES macro
2015-05-28 00:19:48 -07:00
Scott Lahteine
76b4678f99
Merge pull request #2171 from thinkyhead/gcode_110_is_good
...
M110 is a known command
2015-05-26 21:17:58 -07:00
Scott Lahteine
03d5709b09
M110 is a known command
...
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
2015-05-26 20:31:18 -07:00
Scott Lahteine
d76a01194d
Slight size reduction by adding idle()
2015-05-26 20:08:21 -07:00
AnHardt
da246f5cb1
Activate BED_MINTEMP error.
...
And call _temp_error() directly for ERR_MAXTEMP_BED to avoid the only one time use of bed_max_temp_error().
Includes #2156 .
2015-05-25 13:23:19 +02:00
AnHardt
959da98d8e
Call kill() only once when triggered by a temperature error
...
to avoid stack overflow when called from interrupt.
Some clean up for calls of disable_all_heaters().
'disable_all_heaters()' is called in kill() and again when 'killed' is already set inside _temp_error().
2015-05-25 12:44:03 +02:00
Scott Lahteine
68f6f149d0
Reduce code size with out_of_range_error function
...
- Affects code size when automatic bed leveling is enabled
2015-05-24 20:18:02 -07:00
wurstnase
94120740d8
faster compare
...
!(~(ab)&0x3) and ab == 0x3 are equal
2015-05-23 07:55:15 +02:00
Scott Lahteine
c9141e604a
Merge pull request #2145 from thinkyhead/gcode_folding
...
Indentation in process_commands
2015-05-22 18:47:37 -07:00
Scott Lahteine
b55f8718c3
Indent G90/G91, G92
2015-05-22 17:34:08 -07:00
Scott Lahteine
b0d520b109
Indent G30, G31/G32
2015-05-22 17:33:17 -07:00
Scott Lahteine
ffe27a6225
Indent G29
2015-05-22 17:32:46 -07:00
Scott Lahteine
86083badc2
Indent G4, G10/G11, G28
2015-05-22 17:32:27 -07:00
Scott Lahteine
47d7a9cb5e
Indent G2/G3
2015-05-22 17:31:38 -07:00
Scott Lahteine
350f239d84
Indent G0/G1
2015-05-22 17:31:24 -07:00
Scott Lahteine
672b0c1fd3
Cleanup pins in RAMPS_13_EFB boards
2015-05-22 16:20:54 -07:00
Scott Lahteine
15a2351675
No need for +1 on initial seen_pointer
2015-05-22 15:31:30 -07:00
Scott Lahteine
550dd87b2a
Set seen_pointer before calling code_value
2015-05-22 15:11:48 -07:00
Scott Lahteine
38cc0b93c6
Merge pull request #1874 from AnHardt/Bulgarian
...
Introduction of Bulgarian - language_bg.h
2015-05-22 13:59:50 -07:00
Scott Lahteine
04a1622172
Merge pull request #2127 from Wackerbarth/Kossel_Pro
...
Kossel Pro
2015-05-21 18:43:26 -07:00
Scott Lahteine
81c2ca3e10
Merge pull request #2131 from thinkyhead/bq_is_ramps_13_efb
...
Witbox and Hephestos are RAMPS EFB
2015-05-21 18:39:02 -07:00
Scott Lahteine
f919a2fed1
Merge pull request #2134 from AnHardt/preheat-all
...
Shift call of start_watching_heater() into setTargetHotend()
2015-05-21 18:36:28 -07:00
Scott Lahteine
063881b5bd
Fix a couple of doubled semicolons
2015-05-21 18:15:29 -07:00
