Scott Lahteine
3bc2273ac9
Comment M540
2016-11-21 18:08:00 -06:00
Scott Lahteine
14b74181f5
Merge pull request #5179 from thinkyhead/rc_TMC2130
...
TMC2130 "Silent StepStick" support
2016-11-21 14:10:52 -06:00
Scott Lahteine
bb2114a060
Merge pull request #5264 from thinkyhead/rc_delta_safe_zone
...
Add an option for delta to home to the top
2016-11-21 13:56:44 -06:00
Scott Lahteine
9b96a4a53b
Merge pull request #5246 from thinkyhead/rc_some_cleanup
...
Minor stepper cleanup
2016-11-21 13:55:25 -06:00
Scott Lahteine
3e0376b45e
Reorder M114 and M119 gcode cases
2016-11-21 00:52:19 -06:00
Scott Lahteine
127e21ae00
Extend M122 for all steppers
2016-11-21 00:52:18 -06:00
Moritz
d67c1d825f
Add TMC2130 support
2016-11-21 00:17:45 -06:00
Scott Lahteine
11effeee2c
Add an option for delta to home to the top
2016-11-20 23:12:07 -06:00
Scott Lahteine
87b6b19256
Patch CASE_LIGHT typo
2016-11-18 23:49:12 -06:00
Scott Lahteine
181cdb3cfe
Move GCode list above include lines
2016-11-18 22:24:46 -06:00
Scott Lahteine
eb120e518c
Followup to new endstop interrupts feature
...
- Fix typos, verbiage
- Fix naming of `setup_endstop_interrupts`
- Some formatting, indentation, spacing
2016-11-18 21:53:45 -06:00
Scott Lahteine
832fe284b4
Merge pull request #5184 from AnHardt/endstop_interrupts
...
Introduce endstop interrupts
2016-11-18 20:50:24 -06:00
Scott Lahteine
98600e1433
Minor stepper cleanup
2016-11-18 01:15:57 -06:00
Florian Heilmann
d08867986e
Add autotemp capabilities to M104
...
This allows M104 to pass the F and B parameters to enable autotemp as well
2016-11-17 11:28:19 -06:00
Scott Lahteine
2330619da0
Merge pull request #5191 from petrzjunior/const
...
Replace const bool with #define for consistency
2016-11-17 03:37:32 -06:00
Petr Zahradník junior
d7ce5d271b
Replace const bool with #define for consistency
2016-11-16 18:55:21 +01:00
Scott Lahteine
5d23e52d75
Merge pull request #5228 from thinkyhead/rc_keep_last_mix
...
Fix DIRECT_MIXING_IN_G1 to preserve the previous mix
2016-11-15 19:12:01 -06:00
Scott Lahteine
99b0c1fe56
Fix DIRECT_MIXING_IN_G1 to preserve the previous mix
2016-11-15 16:12:26 -06:00
Scott Lahteine
410657b050
Fix G30 with limits, print correct probe XY
2016-11-15 14:10:28 -06:00
AnHardt
f3eee02596
Introduce endstop interrupts
...
If ENDSTOP_INTERRUPTS_FEATURE is enabled this tries to set up interrupt routines
for all used endstop pins. If this worked without errors, `endstops.update()` is called
only if one of the endstops changed its state.
The new interrupt routines do not really check the endstops and react upon them. All what they
do, is to set a flag if it makes sense to call the endstop test we are used to.
This can be used on:
* ARM (DUE) based boards - all pins can raise interrupts,
* RAMPS - all 6 endstop pins plus some other on EXT-2 can raise interrupts,
* RAMPS based boards - as long the designers did not change the pins for the endstops or at least left enough,
* all boards, if there are enough pins that can raise interrupts, and you are willing/able to swap with pins dedicated to other purpose.
2016-11-15 12:07:41 +01:00
Scott Lahteine
665b7f3893
Merge pull request #5212 from thinkyhead/rc_mixing_faster
...
Store mix factors as reciprocals and multiply
2016-11-12 18:47:11 -06:00
Scott Lahteine
60cc9342a4
Merge pull request #5188 from thinkyhead/rc_extended_host_support
...
Extended host support: M155 Auto temp report, M115 capabilities
2016-11-12 15:38:06 -06:00
Scott Lahteine
f663220e87
Store Mix factors as reciprocals and multiply
2016-11-12 15:19:18 -06:00
Scott Lahteine
b31a07e261
Stateful M355 with separate P parameter
2016-11-09 03:28:18 -06:00
Scott Lahteine
3c9a838651
Extended capabilities report in M115
2016-11-09 02:32:58 -06:00
Scott Lahteine
68b866b5dd
Add M155 - Auto-report temperature with interval
2016-11-09 02:32:58 -06:00
Scott Lahteine
75bfde9945
M155=>M260, M156=>M261
2016-11-08 17:54:54 -06:00
Scott Lahteine
dcfd7c69e8
Merge pull request #5163 from nzinov/RCBugFix
...
Improve G30 probing command - add optional arguments
2016-11-07 11:37:13 -06:00
Scott Lahteine
e765eebfb0
Patch spacing in bilinear grid report
2016-11-07 04:08:25 -06:00
Nikolay Zinov
dea00bbcf1
improve G30 probing
...
Add optional parameters
X, Y for probe point
S sets stowing on and off
2016-11-05 13:22:45 +03:00
Scott Lahteine
176aeafc19
Don't define bilinear_line_to_destination on kinematic setups
2016-11-03 14:10:07 -05:00
Scott Lahteine
236853df22
Corrections to bilinear_line_to_destination
...
- Allow more than 9x9 probe points
- Account for the probe starting position
2016-11-03 04:43:59 -05:00
Scott Lahteine
0115e495fe
Fix up Dual X switch blocks
2016-11-02 21:38:50 -05:00
Scott Lahteine
2495ab7af2
Make dual_x_carriage_mode an enumeration
2016-11-02 21:38:49 -05:00
Scott Lahteine
d6c36f5bb9
Fix Z raise with DXC_AUTO_PARK_MODE
2016-11-02 21:36:50 -05:00
Scott Lahteine
0c79553fc5
Cast int to AxisEnum for some accessors
2016-11-02 17:42:24 -05:00
Scott Lahteine
adbf1f7dca
Add M355 to the GCodes list.
2016-11-02 16:43:52 -05:00
Scott Lahteine
63efc10599
Merge pull request #5134 from thinkyhead/rc_bilinear_split_lines
...
Split cartesian moves on grid boundaries with bilinear ABL
2016-11-02 16:14:55 -05:00
Scott Lahteine
ee5b8d6dc8
Split moves on grid boundaries with bilinear ABL on cartesian
2016-11-01 08:25:47 -05:00
Scott Lahteine
66744a6076
Merge pull request #5133 from thinkyhead/rc_M355_case_light
...
M355 Case light
2016-11-01 07:51:27 -05:00
Scott Lahteine
955d14acb0
Patch photo pin code style
2016-11-01 06:30:14 -05:00
Stanley
ab3f966f5f
Case light G-code M355
...
implemented G-Code M355 into Marlin
2016-11-01 06:30:14 -05:00
Sebastianv650
f9bea7968f
BugFix for incorrect E-speed calculation
...
The extrusion speed was wrong due to a not high enough precision of
esteps to XY steps, therefore now the target float values are used to
calculate the ratio between XY movement and extrusion speed.
The e_speed_multiplier8 was replaced by an absolute multiplier called
abs_adv_steps_multiplier8, therefore one multiplication and bitshift can
be saved inside the stepper ISR. Due to this, also extruder_advance_k is
better suited inside the planner and not the stepper files any more.
2016-11-01 08:08:47 +01:00
Scott Lahteine
ff3a8ca0d1
Use NUM_DIGITAL_PINS instead of custom DIO_COUNT
2016-10-31 08:08:03 -05:00
Scott Lahteine
04a1fac029
Some cleanup to M43
2016-10-31 08:08:03 -05:00
Bob-the-Kuhn
c7f1f0dae6
Add endstop monitor & make pins report pretty
2016-10-31 08:08:02 -05:00
Scott Lahteine
396434a445
Fix compiler warning in M145
2016-10-28 20:57:36 -05:00
Scott Lahteine
07bfc45df8
Adjust spacing in gcode_M149
2016-10-28 20:57:36 -05:00
Scott Lahteine
1a2310c494
Make LCD preheat vars an array to reduce code size
2016-10-28 20:57:36 -05:00
Scott Lahteine
50ee749082
Centralize click-handling in the LCD loop
2016-10-28 20:57:21 -05:00
