MPCNC/Firmware2
1
0
Fork 0
Code Issues 1 Pull Requests Releases Wiki Activity
777 Commits 1 Branch 0 Tags 129 MiB
67710df9f3
Commit Graph

700 Commits

Author SHA1 Message Date
Daid
ca7acbe6d9 Allow specification of which arduino hardware subvariant in Makefile. 2012-12-09 19:19:57 +01:00
Johann Rocholl
33247733e0 Teensylu and Printrboard use different analog pins for thermistors. 2012-12-09 02:19:13 -08:00
Johann Rocholl
621c24a10f AT90USB is only defined after pins.h is included. 2012-12-09 01:40:33 -08:00
Johann Rocholl
6cba11f087 Stop redefining MOTHERBOARD and #define AT90USB instead. Also put #ifndef AT90USB around the HardwareSerial_h trick, so now Printrboard / Brainwave support compiles on Arduino 1.0.2 as well. 2012-12-09 01:32:09 -08:00
Johann Rocholl
4d351b4846 Improved formatting and comments for consistency. 2012-12-08 20:15:53 -08:00
Johann Rocholl
a30007caa4 If fastio.h is not messed up then Teensylu and Printrboard are actually using the same pins. 2012-12-08 19:46:42 -08:00
Johann Rocholl
6aa87a7b67 Use the same fastio.h definition for AT90USB1286/7 and AT90USB646/7. 2012-12-08 15:16:38 -08:00
Johann Rocholl
b1c38d4c82 Avoid compiler warnings (redefined MOTHERBOARD) in Arduino 1.0 and greater. 2012-12-08 11:34:18 -08:00
Johann Rocholl
42e21bb06e Add support for Printrboard (from https://github.com/lincomatic/Marlin) and Brainwave (from https://github.com/metrix/Sprinter). 2012-12-08 10:49:01 -08:00
Johann Rocholl
ce4b5bbeaa Add AT90USB646 support from Sprinter to fastio.h. 2012-12-08 10:45:58 -08:00
Daid
f413aa33b3 Small makefile change, posibility to add defines on the commandline, and fix compiling with watchdog enabled when using the Makefile. 2012-12-08 11:49:53 +01:00
daid303
587154c01b Fix the WATCHPERIOD implementation. It did not work correctly in a multi extruder setup, it did not work after 32 seconds after startup (int16 used as millies timestamp). And it did not work if you gave an M104 or M109 when the target was already around the target setpoint. So on average, it did not work at all. The new implementation should be robust in detecting a failure to heat up. 2012-12-06 10:36:07 +01:00
daid303
1f27870d41 Fix compiling the watchdog error message when the manual reset watchdog is used. 2012-12-06 10:27:50 +01:00
daid303
c5d4225804 Mistake there, not sure why I did that. My bad. 2012-12-05 20:23:13 +01:00
daid303
529748894c Minor changes in the temperature code for some cleanup. 2012-12-05 19:54:01 +01:00
daid303
4e26ecc940 The Partial release message (which does not really tell you anything) overwrites the final print time on the LCD, which is a real shame. So I removed the message. 2012-12-05 19:32:26 +01:00
daid303
c421774422 The Partial release message (which does not really tell you anything) overwrites the final print time on the LCD, which is a real shame. So I removed the message. 2012-12-05 19:32:02 +01:00
daid303
16078e47d4 Fixed #325 2012-12-04 16:27:21 +01:00
daid303
6a9bee27cc Changed the naming of some LCD functions, so the names match better what the function does. Also moved around some prototypes for general cleanup. 2012-12-03 12:52:00 +01:00
daid303
94ea26ff46 Some minor changes on code style. And a bugfix where the counters for positioning in the stepper where wrong depending on compiler settings. (Caused strange values to reported back with M114 and endstop triggers). Also fixed compiling with FWRETRACT enabled. 2012-12-03 12:13:20 +01:00
daid303
6c51fe5039 Fix the bug where the SD percentage calculation is wrong when the file is larger then 42MB 2012-12-03 11:35:36 +01:00
brupje
57429cb9fe Fix for keypad 2012-11-29 21:42:19 +01:00
daid303
97fa2a9c30 Few simple fixes that save RAM, as static strings are stored in RAM by default. 2012-11-28 10:30:34 +01:00
Daid
c94ca24adc Fixed #317 2012-11-24 17:32:30 +01:00
Daid
99e9554edd Some fixes in the Makefile to support Arduino 1.0.0 or higher and added the Rambo. Still needs some more work for the different arduino hardware variants. 2012-11-24 11:46:31 +01:00
Erik vd Zalm
dbbf050005 More rambo fixes 2012-11-21 20:53:56 +01:00
Erik vd Zalm
f934d0ef5b Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1 
Conflicts:
	Marlin/Configuration.h
 2012-11-21 20:36:30 +01:00
Erik vd Zalm
e48dfcc2b3 Tmp copy before merge 2012-11-21 20:29:31 +01:00
Erik vd Zalm
b98fb17fe9 Small FREQUENCY_LIMIT changes 2012-11-21 20:17:44 +01:00
daid
bce67ec2c9 Merge pull request #312 from gege2b/Marlin_v1 
Added french translation
 2012-11-18 13:43:07 -08:00
Gege
9b1d2483a0 I hope last changes to french translation 2012-11-18 22:34:56 +01:00
Gege
b1adc567da Correction to french translation (non-ASCII chars only) 2012-11-18 20:00:41 +01:00
Gege
0807d82af0 Correction to french translation (plain text only) 2012-11-18 19:39:56 +01:00
Erik vd Zalm
5cd7a90b32 Added new temperature lookup table creation tool. This one uses stein hart-hart equations. 
You need 3 temperature resistance:combinations. This gives a better result then using beta.
 2012-11-16 23:51:05 +01:00
gege2b
bb119739b0 Added french translation 2012-11-16 18:38:50 +01:00
daid
df8dd5ac21 Merge pull request #306 from nothinman/Marlin_v1 
Added automatic build numbering.
 2012-11-14 01:59:33 -08:00
MaikStohn
2b7b1e52b1 allow marlin internal 0°C represenation 2012-11-13 14:37:08 +01:00
Martin Lukasik
2f771b3979 Added automatic build numbering. 2012-11-12 21:06:59 +00:00
daid
9bebe9b631 Merge pull request #302 from nothinman/Marlin_v1 
Added Polish translation. Cosmetic changes to English.
 2012-11-12 12:13:30 -08:00
daid303
a2032afa3a Fixed #303 2012-11-12 21:04:07 +01:00
Martin Lukasik
6a55ca8370 Added Polish translation. Cosmetic changes to English. 2012-11-12 15:54:07 +00:00
daid303
8f20562f49 Fix some of the crowded code style. And fixed the conditional. #300 2012-11-12 15:49:40 +01:00
daid303
43018a48c4 Fix for a few -Wextra warnings. 2012-11-12 15:35:28 +01:00
daid303
72586eb30a Solved few warnings. 2012-11-12 09:29:12 +01:00
daid303
7a02ba361c Header multiple include protection should match the filename, not just _ARDUINO_H, which is almost bound to go wrong some day. 2012-11-12 09:24:28 +01:00
daid303
f4a89ec776 SDCARDINSERTED is always defined, and thus we do not need the #ifdefs. 2012-11-12 09:16:27 +01:00
daid303
57834776ad Made the 2nd speed lookup table condition more explicit. 2012-11-11 12:02:48 +01:00
Daid
caa2b25b40 Fix Gen7 compile if you have avr-libc version 1.7.1 or higher. See http://code.google.com/p/arduino/issues/detail?id=604 2012-11-11 11:17:54 +01:00
daid303
a27fef8750 Store the pre-heat constants outside of the ULTIPANEL define, so we can use them when storing EEPROM in a build without the ULTIPANEL. 2012-11-11 11:06:58 +01:00
daid303
789be03b4f Update on makefile, should make it easier to compile for different boards without changing the makefile. (Still missing Arduino 1.x.x support). 2012-11-11 11:05:52 +01:00
daid303
40ce057a3e Fixing issue #297 2012-11-10 14:37:01 +01:00
daid303
625ac81acc Yes, makes sense, lets NOT use the value directly from the configuration define but modify it before setting it. This will not confuse people (including me) at all! 2012-11-09 22:36:31 +01:00
daid303
ffc69537aa Update on some comments, make the MOTHERBOARD list complete again. 2012-11-09 09:10:51 +01:00
daid303
71efcfc648 Most likely fixing issue #295. 2012-11-08 21:08:05 +01:00
daid303
04be9d6001 God damn. Sorry, my mistake, forgot to add this file. 2012-11-07 23:16:43 +01:00
daid303
c17da4b707 Add ConfigurationStore to the Makefile. 2012-11-07 22:43:01 +01:00
daid
ccd9fd0dc3 Merge pull request #292 from jothan/lcdfix 
Lcd fixes
 2012-11-07 13:10:59 -08:00
Jonathan Bastien-Filiatrault
46b9988e26 Search and replace failure. 2012-11-07 16:09:30 -05:00
Jonathan Bastien-Filiatrault
0f73afb0b0 Avoid defining overriding definitions for the RepRapDiscount Smart 
Controller. Remove common definitions. Harmonize declaration order.
 2012-11-07 16:04:28 -05:00
Jonathan Bastien-Filiatrault
36b452c7ac Remove abbrs. 2012-11-07 15:42:18 -05:00
YanFM
332344bd43 Update Marlin/language.h 
Included Portuguese language
 2012-11-07 09:43:13 -02:00
daid303
e6c1cadea0 Set the watchdog to a 4 second timeout, as with 1 second it can timeout during SD card init. 2012-11-07 12:32:17 +01:00
daid
faea7d72b8 Merge pull request #290 from buildrob/Marlin_v1 
Clean up special serial port cases
 2012-11-07 02:00:26 -08:00
daid303
12a4d60e18 Fix the EEPROM storage, no longer inline it at multiple locations, and remove the template. 2012-11-07 10:02:45 +01:00
Jonathan Bastien-Filiatrault
9606f4d04f Include Marlin_main.cpp in source files. 2012-11-06 20:32:48 -05:00
Jonathan Bastien-Filiatrault
3cbaad9288 RepRapDiscount Smart Controller pin definitions. 2012-11-06 20:32:13 -05:00
Robert F-C
99692dc99e Clean up special serial port cases 
Assume SERIAL_PORT 0 if not defined. Collapse un-numbered register
special case. Clarify comments.
 2012-11-07 09:00:21 +11:00
daid303
5a998558a9 Update suggested by Robert F-C. #289 2012-11-06 21:04:29 +01:00
daid303
f6ff0ab767 signed/unsigned fixes. 2012-11-06 15:33:49 +01:00
daid303
5d471e0f34 Also reset the PID values to defaults. Fixes #281 2012-11-06 15:21:00 +01:00
daid303
d3ebc34958 Hopefully also support chips with a single UART in MarlinSerial now. 2012-11-06 14:43:36 +01:00
daid303
b6ff45254e Better explain the watchdog "problem" and rename the config define so it explains that the feature belongs to the watchdog. 2012-11-06 13:33:00 +01:00
daid303
7e348fcb5f By mistake enabled the watchdog by default. This should be off by default. 2012-11-06 13:20:08 +01:00
daid303
06b58a9c4f First cleanup. Moved all code to cpp files, so there are no dependencies on pde files. And no more odd requirement to cat files together. (Still need to fix the Makefile). Also cleaned up some defines and made defines upper case as by C coding conventions. 2012-11-06 12:06:41 +01:00
daid
539f3b3fe4 Merge pull request #284 from brackendawson/Marlin_v1 
Use the right pins for Gen7 1.4
 2012-11-06 01:06:24 -08:00
Robert F-C
65c9a0728f Set default serial port back to 0. 2012-11-05 22:15:07 +11:00
Robert F-C
ab9d183024 Make serial port configurable. 
This change makes the choice of serial port configurable so that
wireless capability can be easily added by connecting Bluetooth modules
(such as BlueSmirf or JY-MCU) to the expansion port pins.
 2012-11-05 21:34:27 +11:00
Bracken Dawson
f5631a89e8 Add dummy Emergancy Pin to Gen7 1.4 
Change required after pulling from ErikZalm.
 2012-10-26 22:28:37 +01:00
Bracken Dawson
a4f9e1ebf2 Merge git://github.com/ErikZalm/Marlin into Marlin_v1 2012-10-26 22:20:35 +01:00
Bracken Dawson
2873d67b17 Put bogus temp override back in Gen7 up to 1.3 
Took out the ifdef when I split 1.4 out and forgot to permanently
define it for <=1.3.
 2012-10-26 22:17:26 +01:00
ErikZalm
a7e40b2903 Merge pull request #276 from setar/Marlin_v1 
Fix num of digits on LCD for E and Z axis.
 2012-10-23 09:48:55 -07:00
MaikStohn
6ed02c86be Fixed wrong code (will not even compile when EXTRUDERS>2) 2012-10-23 18:08:43 +02:00
Sergey Taranenko
2a67363e27 Fix ‘prog_uchar’ definition in LiquidCrystalRus.cpp 2012-10-22 11:05:17 +04:00
Sergey Taranenko
205304ddee Merge git://github.com/ErikZalm/Marlin into Marlin_v1 2012-10-22 10:59:27 +04:00
Erik vd Zalm
58bca87c72 fix LCD temp bed artifacts on power up ' B022/0.) -> B022/000 ' 2012-10-21 14:40:06 +02:00
Erik vd Zalm
febeb43197 Revert "fix LCD temp bed artifacts on power up ' B022/0.) -> B022/000 '" 
This reverts commit cb02c2f9d8.
 2012-10-21 14:36:31 +02:00
Sergey Taranenko
8178dec4c3 Fix num of digits on LCD for E and Z axis. 
The number of steps per mm often contains 4 digits before the decimal point and does not require precision greater than 0.1
 2012-10-18 17:45:40 +04:00
ErikZalm
70f57a6844 Merge pull request #273 from setar/Marlin_v1 
fix LCD temp bed artifacts on power up ' B022/0.) -> B022/000 '
 2012-10-17 04:10:18 -07:00
ErikZalm
ff14199e58 Merge pull request #270 from jothan/Marlin_v1 
Create an explicit rule for building applet/Marlin.cpp.
 2012-10-17 04:09:36 -07:00
Daniele Sdei
695938ba3f Italian language support 2012-10-17 12:48:26 +02:00
Sergey Taranenko
cb02c2f9d8 fix LCD temp bed artifacts on power up ' B022/0.) -> B022/000 ' 2012-10-17 10:49:05 +04:00
Jonathan Bastien-Filiatrault
e4a5e333ef Generalize. 2012-10-15 21:34:33 -04:00
Jonathan Bastien-Filiatrault
e10d3136c8 Create an explicit rule for building applet/Marlin.cpp. 
It would seem that the pattern matches do not work when the source
file is created when make is running. The result of this is that it is
necessary to run "make" twice to build the firmware.

This adds an explicit rule without a pattern match for building
applet/Marlin.cpp it corrects the make behaviour at the cost of adding
a little redundancy in the Makefile.
 2012-10-15 21:16:25 -04:00
ErikZalm
9f089756b7 Merge pull request #265 from setar/Marlin_v1 
Added Russian translation
 2012-10-14 14:11:58 -07:00
brupje
326423719f Add support for Megatronics 2012-10-14 14:05:57 +03:00
brupje
d07b6e93d5 Add support for Megatronics 2012-10-14 14:05:12 +03:00
Sergey Taranenko
efcc28d347 Fix check for include LiquidCrystalRus.h 2012-10-13 00:29:34 +04:00
Sergey Taranenko
cfc193cdac Enables support the Cyrillic alphabet for LCD 2012-10-12 19:06:43 +04:00
Sergey Taranenko
24bcc9647d Added Russian translation 2012-10-12 18:33:05 +04:00
Mark Finn
bf7e453d02 Unwanted artifacts from unclean merge of bed-pid tree 2012-10-09 14:47:35 -05:00
ErikZalm
36a746d7d5 Merge pull request #244 from markfinn/pidbed 
PID for heated bed
 2012-10-08 11:15:16 -07:00
elgambitero
df09e2adce Spanish updated 2012-09-26 19:14:07 +02:00
elgambitero
ddf6603d81 Spanish language updated. Bug fixes on dialogs. 2012-09-26 19:11:45 +02:00
elgambitero
4bf8b1aeee fesfas 2012-09-26 19:05:31 +02:00
drakelive
be1e099f1b Union whit Erick version 2012-09-25 19:17:15 +02:00
elgambitero
7afd202b89 New dialogs translated to spanish. Bug fixes. 
Dialogs from M119 translated, and "Set Preheat" dialogs adapted to the
screen size.
 2012-09-25 19:16:57 +02:00
elgambitero
ebc4601185 Some new dialogs translated to Spanish 2012-09-25 19:08:44 +02:00
drakelive
c8ea9b0e58 Merge branch 'Marlin_v1' of https://github.com/Drakelive/Marlin 2012-09-25 18:51:20 +02:00
drakelive
ca7ca4572e primo commit 2012-09-25 18:46:38 +02:00
johnnyr
8016f058bc fix max endstop pins 2012-09-19 13:15:17 -05:00
Mark Finn
d197f8504b clean up and changes from testing 2012-09-17 19:18:50 -05:00
Mark Finn
eb06a886c4 missed 2012-09-17 14:23:49 -05:00
Mark Finn
04631d2250 cleanup for pull 2012-09-17 14:17:24 -05:00
Mark Finn
0a5ad3ab85 move comment to correct place 2012-09-17 08:42:35 -05:00
ZetaPhoenix
8ac5b29e02 Changes to M119 response for easier visual comparison 
Changed to report on individual lines with "TRIGGERED" or "open" instead of "H" or "L" on one line as H&L could be confused with logic levels High and Low which may be wrong if using inverted logic.  Added strings to language.h.

Fixed typo "deu" in English language that was fixed in #134 but got added back in via 9f7f7354f5
 2012-09-16 14:51:24 -07:00
ZetaPhoenix
c6caa45ae2 Limit Switch locations based on MIN/MAX limits and homing direction 
fixes #246
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
Relocated code based on feedback.
 2012-09-15 15:25:49 -07:00
ZetaPhoenix
dc566d654f fixes #246 
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
 2012-09-14 21:48:49 -07:00
ErikZalm
ba898faa7d Merge pull request #249 from gwelchc/patch-2 
Slight modification for byte savings
 2012-09-14 12:13:36 -07:00
ErikZalm
0152ee71a5 Merge pull request #248 from gwelchc/patch-1 
Binary representation for characters in ultraldc.pde
 2012-09-14 12:10:28 -07:00
G. W. C.
6ccbfeb80c Update Marlin/Marlin.pde 
Added function 'setTargetedHotend' that turns into a function an operation repeated 3 times through the M-codes processing.

This modification saves a few bytes that can be used to add support for new commands.
 2012-09-14 16:38:54 +03:00
G. W. C.
c433142abf Update Marlin/ultralcd.pde 
The joris' char drawins are expressed in binary so to show their content's in a more visual fashion.

This is not a code modification as much as a readibility modification.
 2012-09-14 16:29:43 +03:00
andrey-vasilyev
1d389ad3a8 Fix M81 not working reliably on Gen7 
Some discussion of the issue is here http://forums.reprap.org/read.php?181,118329,page=1
 2012-09-13 19:23:48 +04:00
Mark Finn
9698f4ea64 bed pid 
Conflicts:

	Marlin/Configuration.h
 2012-09-12 21:18:59 -05:00
drakelive
e5c39b7c2a commit 2012-09-10 14:25:49 +02:00
ZetaPhoenix
e8c92e0a95 Missing #else in temperature.cpp prevented reading bed temp when TEMP_BED_PIN <7. Thanks to Leland Wallace for helping me track this down via "Sesame Street" coding (what is not like the other) 2012-09-09 16:06:02 -07:00
drake
bf2071871c Merge branch 'Marlin_v1' of https://github.com/Drakelive/Marlin 2012-09-08 23:08:34 +02:00
drake
fc32e20881 first commit 2012-09-08 22:26:23 +02:00
Erik vd Zalm
abf0693e8e Added KILL_PIN -1 to gen7 boards 2012-09-04 08:20:27 +02:00
Erik vd Zalm
47319cf64e Fixed typo in SF arc fix code. 2012-09-03 21:28:31 +02:00
Erik vd Zalm
e358a2d7af Added fix for SF Arc Point fillet procedure 2012-09-02 01:12:49 +02:00
ErikZalm
044a64a1fb Merge pull request #225 from Justblair/Marlin_v1 
Added PDF file containing Menu Tree for documentation purposes.
 2012-09-01 04:41:49 -07:00
Drakelive
d728e35658 Update Marlin/pins.h 2012-08-30 23:36:49 +03:00
tonokip
1c1fddc7ac Added support for the Rambo reprap electronics board. Added Mcodes to set 
motor current and microstepping pins.
 2012-08-30 00:16:57 -07:00
Blair Thompson
dcd3e8a211 Tidy up 2012-08-29 22:53:41 +01:00
Blair Thompson
ddd9d0cfd4 Added PDF file containing Menu Tree for documentation purposes. Source xlsx document included. 2012-08-29 21:08:41 +01:00
Erik vd Zalm
0e58ef6805 Some dialogs are corrected 2012-08-29 21:15:59 +02:00
Erik vd Zalm
0e89022cc3 Correct temptable_55 name. 2012-08-28 19:47:22 +02:00
Bracken Dawson
47d4f55bc0 Fix Gen7 1.4 pinout 
Gen7 1.4 uses very different pin assignments, might as well make a new
section and remove some of the conditionals from each. It's easier to change
your pin assingment this way if like me you don't wire it exactly to plan.
 2012-08-22 23:15:46 +01:00
elgambitero
6cd150842f Update Marlin/language.h 
Some dialogs corrected and Default language set to 1
 2012-08-22 21:46:22 +03:00
elgambitero
299c18596f Update Marlin/language.h 
Some dialogs are corrected
 2012-08-22 21:44:57 +03:00
ErikZalm
b86336c3f5 Merge pull request #221 from daid/Marlin_v1 
Long filename support for LCD display
 2012-08-22 06:30:35 -07:00
daid
b69e75c89a Added long filename support. 2012-08-22 14:49:57 +02:00
stohn
1d224cc031 merged with upstream and FIXED AGAIN bad translation commit 
PLEASE BE MORE CAREFUL WHEN SUBMITTING NEW TRANSLATIONS

When you add new menu items / messages always copy them to ALL
languages (just use english)
 2012-08-22 13:05:42 +02:00
stohn
06c03fe2f0 new method for message for making KILLED message visible 
The cli(); at the start of the kill() function also stops the internal
arduino timer which stops updating of millis() which prevents the
display of the "KILLED." message.
The new function updates the display directly without checking any
timers.
 2012-08-22 12:44:41 +02:00
daid
87ff61a8a6 Fix for #201 2012-08-22 10:54:55 +02:00
Blair Thompson
aacbebbebe Added Menu Options to the Main-> Control->Temperature Submenu that allow the user to set new values for the ABS and PLA preheat function. EEPROM updated so that these settings can also be committed to EEPROM memory. 2012-08-21 23:46:10 +01:00
stohn
31873ec707 changed int to long to overcome overflow of number display 
- related bug reports: Issue #201, Issue #213
 2012-08-21 16:47:39 +02:00
stohn
de0448343f added KILL_PIN support / cleaned up manage_inactivity function definition 2012-08-21 14:48:29 +02:00
stohn
69961dbba3 fixed incorrect menu messages from last commit... 
- removed several multiple definitions of same message
- fixed definition of missing messages in german and spanish
- tweaked german translation (a lot)
- added note about changing and testing this file
 2012-08-21 14:44:20 +02:00
Blair Thompson
6c050b8440 Fixes error introduced at commit aee475aa55 which caused the sketch not to comile for language option 1. Several defines were removed but still referenced in ultralcd.pde 2012-08-20 21:54:47 +01:00