MPCNC/Firmware2
1
0
Fork 0
Code Issues 1 Pull Requests Releases Wiki Activity
4,764 Commits 1 Branch 0 Tags 129 MiB
d7819298ca
Commit Graph

991 Commits

Author SHA1 Message Date
Richard Wackerbarth
20b4772155 Create DEBUG_LEVELING_FEATURE 2015-08-27 20:52:08 -05:00
Scott Lahteine
194f98ff95 Debug messages for homing and leveling 2015-08-27 20:52:08 -05:00
Richard Wackerbarth
6292d9e815 Rename ENABLE_AUTO_BED_LEVELING 
With the introduction of the #if ENABLED(…)

reads better than
 2015-08-27 20:52:08 -05:00
Christian Lefrançois
9897a9147c Update ABL comments (PR#95) 
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
 2015-08-26 05:51:38 -05:00
Scott Lahteine
23d742bf06 Don't free the stack array plane_equation_coefficients (PR#83) 2015-08-16 06:53:24 -05:00
Scott Lahteine
e3b1e08777 Patch G30 to use raise_z_for_servo (PR#73) 2015-08-15 21:47:04 -05:00
Scott Lahteine
a1eb90d5c0 Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET 2015-08-12 21:26:32 -05:00
Scott Lahteine
91122277f4 Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes 2015-08-12 21:26:25 -05:00
AnHardt
5707a2c3d5 indexindexIntoAB is only vald for !DELTA 2015-08-11 17:32:11 -05:00
AnHardt
d8860f9ad9 Alway end at the same point 
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
 2015-08-11 17:32:11 -05:00
AnHardt
4ca8f4a9a7 Always zigzag 
Use the shortest way between probing-points.
 2015-08-11 17:32:11 -05:00
AnHardt
3d23424121 Add array indexIntoAB[xx][yy] 
and use it.
 2015-08-11 17:32:11 -05:00
AnHardt
e2d69f66b2 Make Z_PROBE a Z_MIN_PROBE (PR#65) 
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.

Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX  check for the probe in update_endstops().

Using an delta related idea of @clefranc from #61,
extended to the general change for all setups.

Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
 2015-08-11 14:41:36 -05:00
Richard Wackerbarth
9d8cc24abf Continue from the line following the M999 (PR#60) 
If the printer is going to accept the M999,
then it should continue from that line number.
 2015-08-08 08:08:02 -05:00
Scott Lahteine
46453905d6 Apply remaining ENABLED/DISABLED conditionals 2015-08-03 16:04:48 -05:00
Richard Wackerbarth
b227d8c128 Supply a VERSION in a short form for displays 
The long descriptor will still be available in M115
 2015-08-03 08:21:09 -05:00
AnHardt
4f46df5dab Make bootscreen configurable for the graphic displays 
Saves about 473 byte of progmem and 28 bytes of RAM.
 2015-08-03 07:13:00 -05:00
Scott Lahteine
b4abb0ae7f Apply ENABLED / DISABLED to Marlin core files (PR#2558) 2015-07-31 01:03:58 -05:00
Scott Lahteine
9d151bb61b servo_endstop_angles -> servo_endstop_angle 2015-07-30 23:35:57 -05:00
Scott Lahteine
1f63293624 servo_endstops -> servo_endstop_id 2015-07-30 23:35:57 -05:00
Scott Lahteine
ed4a6371ad Add HAS_SERVO_ENDSTOPS to simplify conditonals 2015-07-30 23:35:57 -05:00
Scott Lahteine
ae9274be05 Fix minor compiler warnings in for loops 2015-07-30 23:31:58 -05:00
Scott Lahteine
4a58e447a1 Add array size to servo_endstop_angles (PR#2553) 2015-07-30 23:27:38 -05:00
AnHardt
d03f037a92 Get rid of malloc() and free() (PR#2549) 
Just the minimal changes to qr_solve.cpp and .h to get rid of malloc() and free().

Saves about 656 bytes of progmem (library-code)
and 22 bytes for static variables.

Should use exactly the same amount of stack as it did before on the heap.
 2015-07-30 17:50:31 -05:00
Scott Lahteine
3b2b2313ff Combine if block related to SERVO_ENDSTOPS 2015-07-30 16:39:05 -05:00
Scott Lahteine
0af2a80e06 Make SERVO_ENDSTOP_ANGLES 2-dimensional 2015-07-30 16:38:56 -05:00
Scott Lahteine
9f48798ffd Replace ENABLED with DEFINED for SERVO_ENDSTOPS (PR#2542) 2015-07-30 07:55:29 -05:00
Richard Wackerbarth
ae00fad75b Rename as M100 2015-07-27 20:31:59 -05:00
Richard Wackerbarth
a401d738df There is an echo in here 2015-07-27 20:31:59 -05:00
Richard Wackerbarth
ed7d45e8f5 Memory watcher 2015-07-27 20:31:59 -05:00
Scott Lahteine
bea6739774 Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527) 2015-07-27 20:24:33 -05:00
Scott Lahteine
e4c01f1c7e Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507) 2015-07-26 20:40:27 -05:00
Scott Lahteine
e2957df05c Shorthand for do_blocking_move_to 2015-07-24 22:07:41 -05:00
Scott Lahteine
819c5b9b50 Adjust comment on Z adjustment 2015-07-24 22:07:41 -05:00
Scott Lahteine
5a7356b6fc Patch for G29 final Z position 
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
 2015-07-24 22:07:41 -05:00
AnHardt
088e09e052 Add forgotten Marlin_main.cpp 2015-07-24 22:04:49 -05:00
Scott Lahteine
b116c096bd Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512) 
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
 2015-07-24 22:00:25 -05:00
Scott Lahteine
469843427d Reduce code in gcode_M81 (PR#2497) 2015-07-23 08:14:00 -05:00
Scott Lahteine
c66955aaf9 Mark unchanging arrays as const (PR#2494) 
The compiler may be able to optimize if it knows an array won’t be
changing.
 2015-07-22 21:37:37 -05:00
Scott Lahteine
278aa15301 Add COUNT macro and apply 2015-07-22 18:16:05 -05:00
Scott Lahteine
aac2b9aa9d Reduce code in gcode_M84 (PR#2492) 
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
 2015-07-22 17:22:01 -05:00
Scott Lahteine
e83eac312e Move plan_arc next to prepare_move 2015-07-19 16:18:46 -05:00
Scott Lahteine
5c5936508d G2/G3 Arcs for Delta 
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
 2015-07-19 16:18:46 -05:00
Scott Lahteine
3b23ccd366 Patch servos code for move 
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
 2015-07-19 11:24:23 -07:00
Patrick Bogen
fba4e6241b Specify print format for reporting invalid tmp_extruder (PR#2465) 2015-07-18 16:40:01 -05:00
AnHardt
d15d869267 Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464) 
to make clear - it's not a question but an order.
 2015-07-18 10:27:21 -05:00
Scott Lahteine
f209b755a5 Move the Z probe as far as needed to trigger the switch (PR#2461) 2015-07-16 20:02:44 -05:00
Scott Lahteine
0f1df62389 Fixup comments in code_seen 2015-07-16 16:40:52 -05:00
Scott Lahteine
2945eb6650 Call code_seen only once per parameter 2015-07-16 16:40:52 -05:00
Scott Lahteine
db23b9b184 Minor tweak to M204 code (PR#2457) 2015-07-16 16:35:13 -05:00
Scott Lahteine
81d42406b7 Move braces in homeaxis to prevent a hanging else (PR#2451) 2015-07-16 10:25:54 -05:00
AnHardt
ed6598adf5 Corrected Bed Height vs. Bed Topology for verbosity > 3 
and cleaned out some tabs.

Everything else is a rebased PR#2017 as proposed by @CptanPanic
 2015-07-15 19:51:40 -05:00
brian
62302ceb9e Add calculation of difference between auto-correct bed level plane, and measured topo map. 2015-07-15 19:51:40 -05:00
AnHardt
49609f6c14 Activate the new servo.move() function 
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
 2015-07-15 17:39:43 -05:00
Scott Lahteine
87a872e103 Use st_get_position_mm where possible (PR#2411) 2015-07-12 22:15:54 -05:00
Scott Lahteine
2e0da8abdc Allow N to take a negative argument (PR@2402) 2015-07-12 22:14:25 -05:00
Scott Lahteine
447dbd6fa5 Add STEPPER_RESET_PIN support 2015-07-11 16:04:11 -05:00
Scott Lahteine
6b1b8cb2b3 Also nullify spaces before the checksum asterisk (PR#2409) 2015-07-10 09:03:07 -05:00
Scott Lahteine
4e9d658141 Prevent a hanging SERIAL_ECHO_START in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
6b494c1535 Use disable_all_heaters in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
15190d40df Add extra EOL after M111 2015-07-07 06:59:10 -05:00
AnHardt
d421f5250d Correct the sign of zprobe_zoffset for G29 (PR#@391) 
Sign flipped with #2167.
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
 2015-07-07 06:55:33 -05:00
Scott Lahteine
52fcc743ab Replace "target" with "destination" in M600 (PR#2374) 
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
 2015-07-04 05:55:25 -05:00
AnHardt
23c8c5348f Z-height fix V2b (PR#2351) 
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
 2015-07-02 20:30:40 -05:00
Todd Swindoll
a111fbbd0a z-probe offset fix (PR#2361) 
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
 2015-07-02 20:28:07 -05:00
Scott Lahteine
9682ed455e Fix comment on M83, add comment to prepare_move 2015-06-28 08:20:19 -05:00
AnHardt
36746143a1 Correct output of M48 (PR#2336) 
n_samples is an uint8_t .
Got printouts like:
50 of 2  ...
 2015-06-27 06:08:40 -05:00
Scott Lahteine
f6ca5a8da8 Allow "M110 N123" without a checksum 2015-06-26 18:13:54 -05:00
Scott Lahteine
aaad65ff5d Include a comment documenting M110 2015-06-26 18:13:54 -05:00
Scott Lahteine
862c72b030 Put the mandatory test of gcode_N first 2015-06-26 18:13:54 -05:00
Scott Lahteine
30976f9773 Allow M110 to handle a second N argument 2015-06-26 18:13:53 -05:00
Scott Lahteine
5ccb1c9e7d Use millis for M600 audio feedback interval 2015-06-25 20:45:03 -05:00
Scott Lahteine
fb16a83b8a Cleanup M600 documentation comments 2015-06-25 20:45:03 -05:00
Scott Lahteine
97ec224d72 Replace target with destination in M600 2015-06-25 20:45:03 -05:00
Scott Lahteine
4ce9ddbb74 Check the temperature before filament change 2015-06-25 20:45:03 -05:00
AnHardt
722829b058 Move buzzing code to buzzr.h & buzzer.cpp (PR#2307) 
at least the lcd independent part from Marlin_main.cpp.
 2015-06-22 22:31:48 -04:00
schlotzz
1e9cf905c7 Enable ZigZag AutoBedLeveling on Deltas (PR#2273) 
ZigZag has been disabled by fault due to do_topography_map
 2015-06-15 20:26:25 -05:00
AnHardt
6ab7b560af Rework buzzing (PR#2296) 
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.

Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.

All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.

To do: Check the conditions for the BEEPER-pin in all pin-files.
 2015-06-15 06:13:26 -05:00
Scott Lahteine
29122db2fa Fix ULTRA_LCD spelling in HAS_LCD_BUZZ 2015-06-15 06:12:34 -05:00
Scott Lahteine
e2a4a83586 Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281) 2015-06-12 22:39:35 -05:00
MagoKimbra
eb81982fcd Fix error next command in autotune (PR#2274) 
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
 2015-06-12 07:10:38 -05:00
AnHardt
55b23c896a Optimise out_of_range_error() (PR#2265) 
by avoiding the strncopy()
 2015-06-12 02:20:40 -05:00
AnHardt
45642b7fe8 Respect DISABLE_AXIS settings (PR#2216) 
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
 2015-06-11 11:35:05 -05:00
Scott Lahteine
962b107341 Prevent current_command_args from bypassing nul (PR#2270) 2015-06-09 16:07:10 -05:00
Scott Lahteine
ff6081be3a Parse N[0-9]+[ ]* differently (PR #2263) 
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
 2015-06-08 17:06:49 -05:00
Scott Lahteine
96a3fba8ac Reverse the sign of zprobe_zoffset 
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
 2015-06-08 05:09:27 -05:00
paclema
8d295547be * Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button. 2015-06-06 19:45:45 -05:00
Richard Wackerbarth
ad09d6a60f 3 Step Allen Key Probe 2015-06-06 17:48:27 -05:00
AnHardt
e400fce271 Merge pull request #2221 from MagoKimbra/Dryrun 
Insert Debug DRYRUN Repetier Host compatible
 2015-06-03 12:30:48 +02:00
AnHardt
c3fe6e61ae Merge pull request #2229 from AnHardt/position-out-of-range 
Fix out_of_range_error()
 2015-06-03 09:46:22 +02:00
AnHardt
d1f4471000 Merge pull request #2146 from Wackerbarth/Versioning 
Versioning
 2015-06-02 18:31:21 +02:00
AnHardt
17b0ec84ed Fix out_of_range_error() 
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
 2015-06-02 11:50:32 +02:00
AnHardt
35af5ef23e Merge pull request #2225 from Wurstnase/naming 
consistency name for multiplier
 2015-06-02 10:18:22 +02:00
wurstnase
e7e964432b consistency name for multiplier 
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
 2015-06-01 22:33:22 +02:00
MagoKimbra
76306f9073 Insert Debug DRYRUN Repetier Host compatible 2015-06-01 18:34:45 +02:00
MagoKimbra
881146bc22 Fix problem Width Cura 2015-06-01 17:25:32 +02:00
AnHardt
9d2a980bcf Merge pull request #2170 from thinkyhead/beep_M600_elsewise 
Slight size reduction by adding idle()
 2015-05-30 12:42:32 +02:00
AnHardt
2728dc0606 Merge pull request #2194 from thinkyhead/reduce_strings 
Redo "invalid extruder" to save 304 bytes
 2015-05-30 11:05:08 +02:00
Scott Lahteine
be5236e839 Reduce setTargetedHotend by removing the switch 2015-05-29 18:03:58 -07:00
Scott Lahteine
06f401e7e5 Redo "invalid extruder" to save 264 bytes 
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
 2015-05-28 22:25:28 -07:00
Scott Lahteine
1a882bcc2e Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands 
Ignore unknown commands if they start with G, M, or T
 2015-05-28 22:03:48 -07:00
Scott Lahteine
a672872717 Merge pull request #2187 from AnHardt/MAX6675M105 
Print active extruder with M105 for MAX6675
 2015-05-28 18:12:48 -07:00
Scott Lahteine
9beed830eb Drop commented code_is_good lines 2015-05-28 17:53:47 -07:00
Scott Lahteine
068d4a1eb2 Ignore unknown commands if they start with G, M, or T 2015-05-28 17:44:09 -07:00
Scott Lahteine
c5c9d12630 Merge pull request #2183 from AnHardt/displayinit 
Initialize the display earlier
 2015-05-28 16:29:18 -07:00
Scott Lahteine
0564625757 Update M33 for new gcode parser 2015-05-28 14:17:39 -07:00
AnHardt
af7e3f5076 Print active extruder with M105 for MAX6675 
Was omitted when T0 is a MAX6675.
 2015-05-28 19:03:16 +02:00
AnHardt
f0523b5816 Initialize the display earlier 
to have it ready to display errors during (temperature)-setup.
 2015-05-28 16:08:17 +02:00
Scott Lahteine
03d5709b09 M110 is a known command 
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
 2015-05-26 20:31:18 -07:00
Scott Lahteine
d76a01194d Slight size reduction by adding idle() 2015-05-26 20:08:21 -07:00
Richard Wackerbarth
5ea139fd79 Revised Versioning mechanism 2015-05-25 15:53:14 -05:00
Scott Lahteine
68f6f149d0 Reduce code size with out_of_range_error function 
- Affects code size when automatic bed leveling is enabled
 2015-05-24 20:18:02 -07:00
Scott Lahteine
b55f8718c3 Indent G90/G91, G92 2015-05-22 17:34:08 -07:00
Scott Lahteine
b0d520b109 Indent G30, G31/G32 2015-05-22 17:33:17 -07:00
Scott Lahteine
ffe27a6225 Indent G29 2015-05-22 17:32:46 -07:00
Scott Lahteine
86083badc2 Indent G4, G10/G11, G28 2015-05-22 17:32:27 -07:00
Scott Lahteine
47d7a9cb5e Indent G2/G3 2015-05-22 17:31:38 -07:00
Scott Lahteine
350f239d84 Indent G0/G1 2015-05-22 17:31:24 -07:00
Scott Lahteine
15a2351675 No need for +1 on initial seen_pointer 2015-05-22 15:31:30 -07:00
Scott Lahteine
550dd87b2a Set seen_pointer before calling code_value 2015-05-22 15:11:48 -07:00
Scott Lahteine
04a1622172 Merge pull request #2127 from Wackerbarth/Kossel_Pro 
Kossel Pro
 2015-05-21 18:43:26 -07:00
Scott Lahteine
f919a2fed1 Merge pull request #2134 from AnHardt/preheat-all 
Shift call of start_watching_heater() into setTargetHotend()
 2015-05-21 18:36:28 -07:00
AnHardt
0c0ace2a04 Remove start_watching_heater() fom M104 and M109 2015-05-22 01:44:50 +02:00
Scott Lahteine
bde9c70d42 Suppress the line mismatch error after M303 2015-05-21 16:27:22 -07:00
Scott Lahteine
50bd7493cc Merge pull request #2108 from thinkyhead/m33_long_filename_host_support 
M33 LONG_FILENAME_HOST_SUPPORT
 2015-05-21 16:22:47 -07:00
Scott Lahteine
4d11b29959 Merge pull request #2113 from thinkyhead/command_sanitizer 
Command sanitizer
 2015-05-21 16:21:58 -07:00
Richard Wackerbarth
735bf2d35f Describe Custom M Code 2015-05-21 08:06:33 -05:00
Scott Lahteine
f39658c822 M120 and M121 are reversed 2015-05-21 00:17:44 -07:00
AnHardt
89d2ee6f13 Make output on display dependant of ULTRA_LCD 2015-05-20 22:03:16 +02:00
AnHardt
f4a93ed997 Add a string parameter to kill() 
Makes the output on the LCD adjustable.
 2015-05-20 20:53:48 +02:00
Scott Lahteine
a0f362c735 Simplify & optimize with current_command_args 2015-05-18 07:08:04 -07:00
Scott Lahteine
adc8fcb77f More parser comments, optimize code_seen, save with goto 2015-05-18 07:08:04 -07:00
Scott Lahteine
c6d8dd19d9 use fetched value 2015-05-18 07:08:04 -07:00
Scott Lahteine
1116e13f5a Further optimization of command parser 2015-05-18 07:08:03 -07:00
Scott Lahteine
3a4c3ab76e Pre-sanitize the command before handling 
- Use a global pointer for the current sanitized command
- Pre-sanitize the current command to bypass `N` and nullify `*`,
removing the need for handlers to bypass, ignore, or nullify these
parts, and reducing overhead for `code_seen`, etc.
- Pre-skip leading whitespace.
- Only look for G, M, T codes at the start of the command.
- Verify that G, M, T codes are followed by command codes.
 2015-05-18 07:06:51 -07:00
Scott Lahteine
0f2c9bacfd M33 LONG_FILENAME_HOST_SUPPORT 2015-05-17 17:36:32 -07:00
Scott Lahteine
3feaef6526 Have G92 set the nozzle position on Delta and SCARA 2015-05-17 17:08:05 -07:00
Scott Lahteine
6c27eaf864 Merge pull request #2101 from thinkyhead/code_style 
Code style and a dangling "else"
 2015-05-17 03:39:08 -07:00
Scott Lahteine
d580a0d186 Use "+=" in plane rotation 2015-05-17 01:51:14 -07:00
Scott Lahteine
2f3a410cb0 Fix a potential hanging "else" bug 2015-05-17 01:50:30 -07:00
Scott Lahteine
b83e3f0905 Combine "Bed X: " strings 2015-05-17 01:49:52 -07:00
Scott Lahteine
7dfb8becdb Adjust some names and types in Marlin_main.cpp 2015-05-17 01:48:51 -07:00
Scott Lahteine
c966aa26ff Comments in Marlin_main.cpp 2015-05-17 01:47:53 -07:00
Scott Lahteine
c54a2ea042 Adjust spacing in Marlin_main.cpp and stepper.* 2015-05-17 01:47:02 -07:00
Scott Lahteine
072625ccad Update headings in Marlin_main.cpp and stepper.cpp 2015-05-17 01:44:53 -07:00
Scott Lahteine
16032f149f Rename to codenum as a consistency 2015-05-16 23:17:35 -07:00
Scott Lahteine
273a4a253f Merge pull request #2096 from thinkyhead/cherry_picking3 
Hide M117 with no LCD
 2015-05-16 21:10:28 -07:00
Scott Lahteine
64825a3d1e Merge pull request #2095 from thinkyhead/cherry_picking2 
Add gcode_line_error to reduce code size
 2015-05-16 21:09:15 -07:00
Scott Lahteine
ca79282eaf Hide M117 with no LCD 2015-05-16 20:59:04 -07:00
Scott Lahteine
ce218cafdb Add gcode_line_error to reduce code size 2015-05-16 20:54:58 -07:00
Scott Lahteine
46d59784ad Rename preocess_command to process_next_command 2015-05-16 20:47:40 -07:00
Scott Lahteine
19166a92e4 Merge pull request #2057 from Wurstnase/serial_wait 
add plan buffer remaining for 'P' and block buffer remaining 'B'
 2015-05-14 04:57:08 -07:00
Scott Lahteine
e97fcafd0e Merge pull request #2076 from thinkyhead/mendel_inverting 
Use MSG_OK in M105
 2015-05-14 04:54:11 -07:00
Scott Lahteine
0f6cd3640b Drop extraneous ok_to_send 2015-05-14 04:38:09 -07:00
Scott Lahteine
0ce355d9e7 Use MSG_OK in M105 2015-05-14 03:33:38 -07:00
Scott Lahteine
7b3acfbb6f Merge pull request #2072 from thinkyhead/better_arc_code 
Consolidate arc code, remove motion_control.*
 2015-05-14 00:27:22 -07:00
Scott Lahteine
68ce419147 Note on segment size 2015-05-13 19:11:36 -07:00
Scott Lahteine
8b92249f18 Bring arc_offset into auto scope 2015-05-13 19:00:46 -07:00
Scott Lahteine
80807b2d71 Consolidate arc code, remove motion_control.* 2015-05-13 18:52:41 -07:00
Scott Lahteine
f65833931d Formatting tweaks 2015-05-13 02:02:19 -07:00
Scott Lahteine
747fd5801c Merge pull request #2055 from thinkyhead/thermal_unified 
Combine thermal runaway and watch-period
 2015-05-12 08:04:29 -07:00
Scott Lahteine
6e5572228d Merge pull request #2064 from thinkyhead/wait_before_g28 
Split up prepare_move by type
 2015-05-12 07:53:11 -07:00
Scott Lahteine
27ad381e25 Allow fractional seconds in G4 and M0 2015-05-12 07:52:08 -07:00
Scott Lahteine
b2bd9aae7c SCARA_SEGMENTS_PER_SECOND 2015-05-12 04:18:15 -07:00
Scott Lahteine
bd20bd5444 Merge pull request #2063 from chris-bo/autobed_sled 
improve sled handling
 2015-05-12 03:29:21 -07:00
Scott Lahteine
9e95ceb3fc Split up prepare_move by type 
- For better encapsulation add inlines for each prepare_move type
- Move controllerFan vars inside the function as statics
- Some formatting cleanup
- Rename `ClearToSend` as `ok_to_send`
 2015-05-12 02:08:20 -07:00
Christian Bohn
f48599f172 add pin definition to some motherboards 2015-05-12 10:02:23 +02:00
Scott Lahteine
b5200e184c Remove extra setup_for_endstop_move 2015-05-12 01:01:53 -07:00
Scott Lahteine
8d814de558 Return void in prevent_dangerous_extrude 2015-05-12 00:55:00 -07:00
Scott Lahteine
367e2eb9f4 Global setup_for_endstop_move 2015-05-12 00:51:22 -07:00
Scott Lahteine
fa951f8a0b Always do st_synchronize() before G28 2015-05-12 00:31:51 -07:00
Christian Bohn
27a3b1d895 disable sled pin by default 2015-05-12 08:51:01 +02:00
Christian Bohn
fb44b53ae3 sled improvements 
- create sled pin definition
- G28 Works with sled
 2015-05-11 23:22:19 +02:00
Wurstnase
46d1932380 add plan buffer remaining for 'P' and block buffer remaining 'B' 2015-05-11 13:04:00 +02:00
Scott Lahteine
8a0dc4d54a Merge pull request #1922 from Wurstnase/serial_wait 
Serial wait
 2015-05-10 23:10:25 -07:00
Wurstnase
526ad82d20 activate advanced_ok and no_timeout 2015-05-11 08:01:51 +02:00
Scott Lahteine
2445ae3d3a Combine thermal runaway and watch-period 
- Make thermal protection for all hotends and/or bed into simple
switches
- Now enable `WATCH_TEMP_PERIOD` when `THERMAL_PROTECTION_HOTENDS` is
enabled
- Move detailed thermal parameters to `Configuration_adv.h`
- Add sanity checks to warn about old configurations
- Change `WATCH_TEMP_PERIOD` to seconds instead of milliseconds
 2015-05-10 22:52:01 -07:00
Scott Lahteine
4097207c75 Merge pull request #2041 from thinkyhead/watch_temp 
More thermal protection
 2015-05-10 21:39:05 -07:00
Scott Lahteine
9b3d4380d3 Only watch the heater that was set 2015-05-10 20:26:45 -07:00
Scott Lahteine
f73f4ce555 Make some z probe and servo code tweaks 2015-05-09 19:11:19 -07:00
Scott Lahteine
54deb9eea3 Enable WATCH_TEMP_PERIOD by default 2015-05-08 22:36:02 -07:00
Wurstnase
0cb87795a3 advanced 'ok' 
ok N(linenumber) P(bufferremaining)
the host can use this to send the data much faster.

Some pseudo code:
If (bufferremaining > 0)  send command
## as long there is free buffer send command

Also
if (linenumber > lastsend - bufferremaining) send command
## as long last linenumber received is bigger than lastsend (host) - last bufferremaining received
 2015-05-08 22:28:51 +02:00
Wurstnase
182e0d99c9 Merge remote-tracking branch 'Marlin8bit/Development' into serial_wait 2015-05-08 21:27:18 +02:00
Scott Lahteine
7f3252eea9 Merge pull request #1999 from paclema/Filrunout_configurable_script 
Added configurable script for filrunout from configuration.h
 2015-05-08 04:39:59 -07:00
Scott Lahteine
79633a74ab Fix MBL compile error 2015-05-06 14:25:13 -07:00
Scott Lahteine
777f2d3820 Merge pull request #2018 from fmalpartida/bugFixing 
Bug corrected: persistent HOMING message when HOME button pressed for homing.
 2015-05-05 00:12:32 -07:00
Scott Lahteine
ecb46de349 Merge pull request #2013 from bq/Fix_lowercase 
Fixed lowercase change missing on commit a22a228b.
 2015-05-04 23:50:56 -07:00
fmalpartida
150a35eff8 Bug corrected: 
Persistent homing message.
Message was declared as an alert, therefore it was persistent.
Updated to message.
 2015-05-04 19:48:49 +02:00
Gina Häußge
ab246ab032 Reverting changes to error messages on serial console 
This reverts the changes done to the error message for line number mismatches done in commit d43cc2dd5f
 2015-05-04 15:03:00 +02:00
Ivan Galvez Junquera
59529b755d Fixed lowercase change missing on commit a22a228b. 
Servo.cpp and Servo.h were changed to lowercase in Makefile but not their actual filenames.
 2015-05-04 09:44:34 +02:00
Scott Lahteine
1f039cde61 Merge pull request #1992 from thinkyhead/too_many_probes 
Stow Z probe on M402 without extra raise
 2015-05-03 20:40:26 -07:00
Scott Lahteine
ca8cec8e8a Merge pull request #1998 from paclema/Filament_runout_fix 
Fixed sintaxis error of filament runout
 2015-04-29 19:53:25 -07:00
Scott Lahteine
d4c74b8f8c Don't apply M428 if an error occurs 
- Also move audio feedback into the command
- Added shorthand for `lcd_buzz` availability
 2015-04-29 19:05:48 -07:00
Scott Lahteine
d065d37822 Add M428 to set home_offset logically 2015-04-29 18:26:16 -07:00
paclema
013a09dbe6 Added configurable script for filrunout form configuration.h 2015-04-29 21:38:40 +02:00
paclema
4dcc0fd55a Fixed sintaxis error of filament runout 2015-04-29 21:32:27 +02:00
Scott Lahteine
ce3caf447b Tweak how homeaxis deploys and stows 2015-04-28 19:17:48 -07:00
Scott Lahteine
a235dca79c Stow z on M402 without extra raise 2015-04-28 19:10:07 -07:00
Scott Lahteine
3688256f86 Merge pull request #1974 from thinkyhead/eeprom_in_gcode 
Make EEPROM reproducible in GCode
 2015-04-27 22:35:41 -07:00
Scott Lahteine
31516e2a3b Merge pull request #1985 from Arengorn/Development 
Update of servo.h
 2015-04-27 22:10:02 -07:00
Scott Lahteine
0f687b5dda Merge branch 'Development' into eeprom_in_gcode 
Latest upstream commits
 2015-04-27 21:47:47 -07:00
Scott Lahteine
28aef684b4 Merge pull request #1957 from Voxel8/sjk/home_y_before_x 
Allow Y to home before X with option in Configuration_adv.h.
 2015-04-27 21:41:14 -07:00
Scott Lahteine
71a0b1a5bb Disable endstops between homing bumps 2015-04-27 21:14:30 -07:00
Scott Lahteine
c36226c4dc Fix homing Z position 
Add `sync_plan_position()` after `axis_is_at_home(axis)` to keep the
planner position in sync when homing.
 2015-04-27 20:55:19 -07:00
Scott Lahteine
ff178d8cf7 Change M421 to take coordinates 
This makes `M421` more amenable for irregular matrices
 2015-04-27 19:48:34 -07:00
Bernardo
ff67ee73fc Update Marlin_main.cpp 
Corrected "servo.h" to "Servo.h" because of the updated filename.
 2015-04-27 23:29:16 -03:00
Steve Kelly
98ca46006c Allow Y to home before X with option in Configuration_adv.h. 
This addresses comments in #1956 and #1079. In particular, this is useful
when both endstops are stationary on a CoreXY system, and the Y axis needs
to be homed before the X so the flags are aligned.
 2015-04-27 16:17:30 -04:00
Scott Lahteine
0fca084ea6 Make EEPROM reproducible in GCode 
With these changes the output of `M503 S0` is all you need to restore
the EEPROM. Building on this it is straightforward to save and restore
the EEPROM state using the SD card or external GCode file.

- Added `M145` to set “heatup states” for the LCD menu
- Added `M420` to toggle Mesh Bed Leveling
- Added `M421` to set a single Mesh coordinate
- Extended `Config_PrintSettings` with added M codes
- Cleaned up some comments here and there
 2015-04-26 20:56:33 -07:00
Scott Lahteine
d43cc2dd5f M111 - Debug Level 
- Add `M111` as a standard option to set the debug level
- Implement `DEBUG_ECHO` in `process_commands`
- Other debug levels (e.g., `DEBUG_DRYRUN`) need more work
 2015-04-26 20:08:45 -07:00
Scott Lahteine
a22a228bcc Rename files to move them in the IDE 2015-04-25 21:04:54 -07:00
Scott Lahteine
0438f0d835 Merge pull request #1924 from thinkyhead/raise_z_for_m401_m402 
Raise Z for M401 and M402
 2015-04-24 22:41:12 -07:00
Scott Lahteine
b275946a52 Merge pull request #1966 from thinkyhead/g4_dwell_message 
G4 shows status message only if no message is set already
 2015-04-24 22:02:37 -07:00
Scott Lahteine
182f2cda35 Minor cleanup of M48 2015-04-24 21:26:36 -07:00
Scott Lahteine
3a6fd912cd Latest upstream commits, merged 2015-04-24 21:14:13 -07:00
Scott Lahteine
3c9e94e035 Merge pull request #1964 from AnHardt/Max6675again 
Add variant for MAX6675 in M104
 2015-04-24 20:44:45 -07:00
Scott Lahteine
56ff46eb8b Improve code_has_value test 2015-04-24 20:43:16 -07:00
Scott Lahteine
ce142afdda G4 shows status message only if no message is set already 
- Address issue raised in #1961
 2015-04-24 20:13:01 -07:00
Scott Lahteine
35e79d56a5 Remove set-coordinate extension of G28 2015-04-24 19:23:12 -07:00
Scott Lahteine
3a74bb5039 Merge pull request #1945 from Wurstnase/max_endstopp 
Max endstopp
 2015-04-24 19:17:38 -07:00
AnHardt
0fed46360c Add variant for MAX6675 in M104 
Else will throw error:
@:0 B@:0
Error:No thermistors - no temperature
[ERROR] Error:No thermistors - no temperature

when no bed is defined
 2015-04-24 16:43:19 +02:00
Scott Lahteine
588ed70d4a Latest upstream commits, merged 2015-04-23 21:18:48 -07:00
Scott Lahteine
0165560333 Apply zprobe_zoffset in axis_is_at_home 
Ensure the probe offset will always be included when homing Z.
 2015-04-23 21:12:38 -07:00
Scott Lahteine
075386e7fe Merge pull request #1959 from thinkyhead/lcd_move_rate 
Include axis parameter to ultralcd's line_to_current
 2015-04-23 21:06:57 -07:00
Scott Lahteine
2558c10c6c Use the slower feedrate for XY axes 2015-04-23 20:06:17 -07:00
Scott Lahteine
64268f3312 Fixup axis_is_at_home a little 2015-04-23 18:16:44 -07:00
Scott Lahteine
996d0a9185 Squish the code down a little 2015-04-23 18:06:36 -07:00
Scott Lahteine
8534bc376c Fix homing of YZ with DUAL_X_CARRIAGE 2015-04-23 17:56:37 -07:00
Scott Lahteine
3b97a7d446 Merge pull request #1944 from AnHardt/beep2 
More Beeper clean up
 2015-04-23 17:50:02 -07:00
Wurstnase
be9e4ceddc fix typo 
c'n'p ftw :/
 2015-04-23 10:35:14 +02:00
unknown
c26d816839 filter any 0 2015-04-22 12:09:57 +02:00
Wurstnase
61ae43f35e v <-> code_value 2015-04-20 23:31:10 +02:00
Wurstnase
da0d91a79b max endstopp 
no user will home to 0 with a max endstopp
 2015-04-20 23:28:46 +02:00
AnHardt
064f2b37d0 More Beeper clean up. 
Centralised beep code to lcd_buzz().
From gcode_M300() and lcd_quick_feedback().

Enforced max. duration for M300 to 5 seconds.

Corrected description in 'Configuration.h'

LCD_FEEDBACK_FREQUENCY_HZ 0 gives now a silent delay of
LCD_FEEDBACK_FREQUENCY_DURATION_MS.
 2015-04-20 11:11:13 +02:00
Wurstnase
92575cecca new timout/add adv_ok 2015-04-20 00:22:40 +02:00
AnHardt
671aaf2dc9 Minor fix for M300 
Corrected wrong order of parameters.
 2015-04-19 13:25:20 +02:00
Scott Lahteine
d931220a65 Tweak comments 2015-04-18 23:12:29 -07:00
Scott Lahteine
47847765e2 Add M410 QuickStop command 2015-04-18 23:07:48 -07:00
Wurstnase
b09a957fce make 'wait' optional and mark as workaround 2015-04-16 21:42:54 +02:00
Scott Lahteine
63b98b8280 Raise Z for M401 and M402 2015-04-16 07:24:33 -07:00
wurstnase
d69da22f7c last_command_time inside get_command() 2015-04-16 16:20:23 +02:00
wurstnase
574e2d856e remove config 2015-04-16 13:07:20 +02:00
paclema
cde5eee2a5 Removed unnecessary comments 2015-04-15 19:01:09 +02:00
paclema
e1b69db6d1 Fixed M48 mismatch between n and P parameter on documentation 2015-04-15 18:17:58 +02:00
Scott Lahteine
e0e68c5cbc Rename servos[] array in Marlin to servo[] 2015-04-14 03:13:25 -07:00
Scott Lahteine
642f6a92bc fix type of code_has_value 2015-04-13 18:02:17 -07:00
Scott Lahteine
17ad80c1e1 Spacing in XYZ_CONSTS 2015-04-13 17:58:47 -07:00
Scott Lahteine
09d60e0128 Naming and code comments 2015-04-13 17:17:36 -07:00
Mehmet Sutas
5a9e45cc4a Fix Syntax Error Filament Runout Statement 2015-04-13 22:37:18 +03:00
Scott Lahteine
ccddc280be Apply three more commits 2015-04-12 22:47:44 -07:00
Scott Lahteine
ac2b23f574 Homing fixes 
- Prevent `Z_SAFE_HOMING` from homing Z twice in some cases
- Allow `G28` with XYZ values of 0 to explicitly set the position
- Don’t add `home_offset` when setting XYZ explicitly in `G28`
- Add `code_has_value` function to check for the presence of a numeric
value (could just test for space or nul to allow other types of values)
 2015-04-11 20:06:48 -07:00
Scott Lahteine
5fe382949b Some G-Codes comment cleanup 2015-04-10 16:16:13 -07:00
Scott Lahteine
8b16ebe705 Break out prevent_dangerous_extrude feature 
- It’s inline here, but could be a macro and duplicated for
`planner.cpp`
 2015-04-09 22:40:37 -07:00
Scott Lahteine
9189cc66ab Fix moves for DELTA for MANUAL_BED_LEVELING 
- Use `line_to_current` in place of `plan_buffer_line`
 2015-04-09 04:32:14 -07:00
Scott Lahteine
2ca099d1e7 Merge pull request #1876 from thinkyhead/cold_extrude 
Catch dangerous extrude before trying several
 2015-04-09 03:21:19 -07:00
Scott Lahteine
a00ebf03d4 Merge pull request #1868 from AnHardt/LCD_STR 
Moved the definitions of the LCD_STR_* to Conditionals.h
 2015-04-09 01:56:23 -07:00
Scott Lahteine
1269c445ab Catch dangerous extrude before trying several 2015-04-09 01:40:48 -07:00
AnHardt
540dbb35e2 And an other MSG_BED in Marlin_main.cpp 2015-04-09 01:16:06 +02:00
AnHardt
14d4419e16 Replaced SERIAL_PROTOCOLPGM(MSG_BED) with SERIAL_PROTOCOLPGM("Bed") 
Resolved some warnings in Marlin_main.cpp regarding compares of signed and unsigned integers by replacing 'int' or 'uint16_t' with 'uint8_t'.
 2015-04-08 23:59:01 +02:00
AnHardt
6a514f3dc9 Aplied HAS_LCD_CONTRAST also to Marlin_main.cpp 
and cleaned typo.
 2015-04-08 13:26:29 +02:00
Scott Lahteine
3162971cd6 current_position not static 2015-04-08 01:05:39 -07:00
Scott Lahteine
27cb90da8b IsStopped / IsRunning inline 2015-04-08 00:56:19 -07:00
Scott Lahteine
e03da4805b Merge pull request #1774 from epatel/Development 
Mesh bed leveling: Added G29 S3 + finer display steps during manual input + bug fix
 2015-04-07 19:24:46 -07:00
Scott Lahteine
f7c4e7e19f Fix G29 not deploying in some instances 2015-04-07 15:38:29 -07:00
Edward Patel
002340f32c Merge branch 'Development-Marlin' into Development 2015-04-07 22:49:12 +02:00
Scott Lahteine
c379f17117 Encapsulate setting of homing_bump_feedrate 2015-04-06 23:21:33 -07:00
Scott Lahteine
d20f42c883 Don't stow the probe until the last grid point! 
- Address Issue #1682 at hash #issuecomment-89756858
 2015-04-06 20:58:09 -07:00
Scott Lahteine
6d084c017f Fix typo in FWRETRACT handler 
Should be `retracting` and not `retract`
 2015-04-06 17:04:22 -07:00
Edward Patel
2f0081bbb5 Compile error fix! Fix for merge artifacts. 2015-04-05 04:16:16 +02:00
Edward Patel
ea10601406 Merge branch 'Development-Marlin' into Development 
Conflicts:
	Marlin/Configuration.h
	Marlin/Marlin_main.cpp
 2015-04-05 04:06:02 +02:00
Scott Lahteine
61f8394361 Compare indices instead of floats for probe actions 2015-04-04 05:01:16 -07:00
Scott Lahteine
0935084141 Fix manage_inactivity 
- Document `manage_inactivity` function
- Allow `EXTRUDER_RUNOUT_PREVENT` to work with all extruders
- Use faster `memcpy` for copying coordinates
 2015-04-03 23:42:50 -07:00
Scott Lahteine
c065da52ec Spacing and spelling 2015-04-03 22:54:48 -07:00
Scott Lahteine
8680b515b0 Fix missing tmp_extruder -> target_extruder 2015-04-03 22:12:49 -07:00
Scott Lahteine
c185912c19 Latest upstream commits, mostly 2015-04-03 21:58:48 -07:00
Scott Lahteine
1e5c18bb14 Add code_value_short and SERIAL_CHAR 2015-04-03 21:43:30 -07:00
Scott Lahteine
84e4edaea7 Add M48 comment for #1794 2015-04-03 19:52:00 -07:00
Scott Lahteine
b98ebd517e disable / enable_all_steppers functions 2015-04-03 19:25:22 -07:00
Scott Lahteine
713953d8c1 Upstream commits, allow no extruder in M105 2015-04-03 19:16:38 -07:00
Scott Lahteine
8f893eb8df Merge pull request #1798 from thinkyhead/fixup_probing 
Fix probe height at G28 start
 2015-04-03 19:03:00 -07:00
Scott Lahteine
dde7e11f8e Merge branch 'Development' into fixup_tr 
Latest upstream commits
 2015-04-03 18:56:52 -07:00
Scott Lahteine
abd7fc36b6 Fix probe height at G28 start 2015-04-03 18:54:55 -07:00
Scott Lahteine
610c8c5471 Merge pull request #1795 from thinkyhead/fixup_probing 
Finish pin tests
 2015-04-03 18:44:44 -07:00
Scott Lahteine
e4934164e4 Merge pull request #1790 from Wurstnase/fix_home_z 
fix feedrate for homing z
 2015-04-03 18:35:09 -07:00
Scott Lahteine
a469d796e1 Add cleanups needed for #1772 2015-04-03 18:14:57 -07:00
Scott Lahteine
c0ca26cd50 Merge branch 'Development' into fixup_probing 
Latest upstream commits
 2015-04-03 18:05:17 -07:00
Scott Lahteine
5c1f08a35f Merge pull request #1772 from croadfeldt/Merge_cleanup 
Z_PROBE_ENDSTOP
 2015-04-03 18:04:31 -07:00
Scott Lahteine
92119d0f7d Static delta[] for SCARA 2015-04-03 16:46:56 -07:00
Scott Lahteine
6b919e14c1 Group all universal variables 2015-04-03 15:45:41 -07:00
Scott Lahteine
21cd2e4fae Merge branch 'Development' into fixup_probing 
Latest upstream commits
 2015-04-03 15:32:15 -07:00
Scott Lahteine
0e8182bbf2 Additional pin tests, cleanup 2015-04-03 15:31:35 -07:00
Wurstnase
45565b680d second wrong feedrate 2015-04-03 18:01:28 +02:00
Wurstnase
581b2aae04 fix feedrate for homing z 
max_feedrate is in mm/s. line_to_destination needs a feedrate in mm/min because there is feedrate/60.
 2015-04-03 16:11:32 +02:00
AnHardt
23cd54755f Fix typo in Marlin_main.cpp 
related to current_position[Z_AXIS] and retract_zlift.

'+ =' -> '+='

Fix for #1786
 2015-04-02 14:50:31 +02:00
Scott Lahteine
e96df67630 Clarify thermal_runaway_protection 
- Add comments documenting `thermal_runaway_protection`
- Add an enum for the thermal runaway states
- Add macros for temperature helper functions
- Fix a glitch with the z probe sled in homeaxis
 2015-04-02 05:10:14 -07:00
Edward Patel
6b91b7b411 Mesh bed leveling: Added G29 S3 + finer steps in manual probing. 
* Use "G29 S3 Xn Yn Zn.nn" to modify bad probed point manually
* Changed manual Z steps from 0.05 to 0.025 and made brought it to Configuration.h
 2015-04-01 21:18:51 +02:00
Chris Roadfeldt
26dc80bf2d Typo fixed... 2015-04-01 13:47:17 -05:00
Chris Roadfeldt
a57862e29f Cleaning up code in prep for merge with upstream. 2015-04-01 11:40:24 -05:00
Chris Roadfeldt
745d9fe1a4 Merge remote-tracking branch 'MarlinFirmware/Development' into Merge_cleanup 
Conflicts:
	Marlin/Marlin_main.cpp
 2015-04-01 10:31:02 -05:00
Scott Lahteine
9593f09b99 Merge pull request #1764 from thinkyhead/probe_leveling 
Fix homing and leveling
 2015-04-01 02:00:39 -07:00
Scott Lahteine
72c7de3570 Cleanup M48 2015-04-01 01:48:45 -07:00