GMagician
7a5b3a1e6a
[1.1.x] Tool change bad behaviour fix
...
Just aligned with version 2.0. Here bug was not present
2017-11-22 23:51:07 +01:00
Scott Lahteine
e2568d7589
Fix delta_safe_distance_from_top
2017-11-22 14:11:04 -06:00
Scott Lahteine
0b1d754e7d
Fix G42
2017-11-22 14:11:04 -06:00
Scott Lahteine
bbc2ee6da1
Don't re-init graphical LCD after boot screen
...
Followup to 13a3fb1acc
2017-11-21 18:21:50 -06:00
GMagician
b96ceb4256
[1.1.x] tool change bad behaviours
...
This PR will address two issues reported in #8492 . Just one is left because I don't know if it is an issue or not
1) when no home is done ("no_move" is set) tool change should never move X & Y because... I don't know where I am...only Z should be adjusted to avoid bed collision if other nozzle is lower than current.
2) Since no move no bed level matrix should be applied
When SWITCHING_NOZZLE is enabled and system is homed there are two movements to go to destination, but first can move Z to older position and then crash on the bed
2017-11-20 16:39:32 -06:00
Bob-the-Kuhn
12b018e619
Merge pull request #8487 from Bob-the-Kuhn/M43-compatibility-1.1.x
...
[1.1.x] M43 end pin correction/compatibility
2017-11-19 11:01:10 -06:00
Bob-the-Kuhn
9b80e1e04a
change to L for end pin for M43 Toggle command
2017-11-18 13:48:53 -06:00
Scott Lahteine
bf6a1816b4
Display volumetric ratio in terms of E mm
2017-11-18 07:03:18 -06:00
Scott Lahteine
622d100c30
No retroactive changes with M851 Z
2017-11-18 03:37:07 -06:00
Thomas Moore
97c19de8b9
Fix PlatformIO dependencies
2017-11-16 15:16:21 -06:00
Scott Lahteine
4e19c59ab3
Miscellaneous cleanup
2017-11-16 01:18:05 -06:00
Scott Lahteine
d3b8f30818
Fix M32 P subroutine handling
2017-11-15 01:09:06 -06:00
Scott Lahteine
95590adf07
Make sure leveled[] is enabled for use
2017-11-14 02:12:20 -06:00
Scott Lahteine
90c7d28055
Extrudrboard support for Printrboard Rev.F
2017-11-13 15:47:03 -06:00
Scott Lahteine
8b684637bc
Merge pull request #8397 from RowanMeara/rm-M428-1.1.x
...
[1.1.x] Fix M428
2017-11-13 15:11:36 -06:00
Rowan Meara
d2df00bfca
[1.1.x] Fix compilation warnings ( #8395 )
...
* Fix up Travis CI and compile warnings/errors
* No ULTRA_LCD with REPRAP_DISCOUNT_SMART_CONTROLLER
* No point in setting all the endstop plugs
2017-11-13 04:18:19 -06:00
Scott Lahteine
25ec0fecfa
Apply native workspace fixes to G92, G53-59
2017-11-13 01:53:44 -06:00
RowanMeara
227b96b28b
Fix M428
...
This fixes the old implementation of M428 which was broken, did not
match the website, and made no sense.
2017-11-13 01:34:43 -06:00
Scott Lahteine
aa616cd410
No leveling data in M114 without leveling
2017-11-12 23:06:16 -06:00
Scott Lahteine
5926159890
Fix report_current_position
...
Thanks @RowanMeara!
2017-11-12 22:57:57 -06:00
Scott Lahteine
5cc87abb3a
Merge pull request #8381 from thinkyhead/bf1_native_followup
...
[1.1] Remove offsets from soft endstops, tool change
2017-11-11 23:13:40 -06:00
Scott Lahteine
355dfed437
Coding standard patch of M290
2017-11-11 22:16:13 -06:00
Scott Lahteine
802ae73b13
Turn off laser power pin when PWM goes to 0
2017-11-11 22:02:19 -06:00
Scott Lahteine
549c814e8d
Remove offsets from soft endstops, tool change
2017-11-11 21:28:32 -06:00
Scott Lahteine
564fbc8dec
M290 constrain patch
2017-11-11 20:50:16 -06:00
Scott Lahteine
df44bcc5ae
Use do_blocking_move_to where possible
2017-11-10 20:37:41 -06:00
Scott Lahteine
3293823642
Add pre-calculated planner.e_factor
2017-11-10 20:09:59 -06:00
Scott Lahteine
24b302c001
Fix cold/lengthy extrusion handling
2017-11-10 20:09:59 -06:00
Thomas Moore
4714fb8fcb
Normalize load/unload length in M600
2017-11-10 19:59:26 -06:00
Scott Lahteine
b0ff3a4c6d
Cleanup around updatePID
2017-11-10 19:17:46 -06:00
LVD-AC
8ce9306b27
PROBE_SELECTED etc.
2017-11-10 19:17:45 -06:00
Scott Lahteine
b6b4bf0959
Merge pull request #8345 from tcm0116/1.1.x-delta_height
...
[1.1.x] Add delta_height variable in lieu of using home_offset
2017-11-09 01:19:48 -06:00
Thomas Moore
658e1ebe5a
Add delta_height variable in lieu of using home_offset
2017-11-08 23:21:02 -06:00
Scott Lahteine
54963cc898
Fix _manual_goto_xy on kinematic systems
2017-11-08 23:18:55 -06:00
Scott Lahteine
ad879a1f90
Clarify some motion code
2017-11-08 23:18:55 -06:00
Scott Lahteine
2559745f54
Tweaks to core motion code
2017-11-08 20:08:20 -06:00
Scott Lahteine
87b655e59e
Fix gcode_get_destination E axis
2017-11-08 12:50:40 -06:00
Roxy-3D
6ee4ba6932
We need motion even with !HAS_MESH ( #8330 )
...
Thank You MagoKimbra !
2017-11-08 09:58:18 -06:00
Scott Lahteine
1d0739d6d1
Patch G33 misuse of PROBE_MANUALLY
2017-11-07 22:28:54 -06:00
Scott Lahteine
5fe15c7f10
Patch abuse of sprintf_P in G33
2017-11-07 17:35:32 -06:00
Scott Lahteine
abb15bc30a
Followup patch for G92
2017-11-07 13:08:38 -06:00
Scott Lahteine
e4466b55b5
Fix G92 for native workspace
2017-11-07 12:27:05 -06:00
Scott Lahteine
26ebeadfaa
Eliminate some compiler warnings
2017-11-06 22:41:27 -06:00
Scott Lahteine
30e4b85587
Fix M118 parameters, with strict guideline
2017-11-06 22:41:27 -06:00
Scott Lahteine
44edffa0a9
Fix SLOW_PWM_HEATERS, issues already patched in 2.0.x
2017-11-06 22:40:44 -06:00
Roxy-3D
12151e62ee
Fix G26's circle drawing... ( #8291 )
...
* Fix G26's circle drawing...
This mostly catches the bugfix-v1.1.x branch up to bugfix-v2.0.0
I'll have to do something similar to get bugfix-v2.0.0 caught up to
bugfix-v1.1.x
* only use planner.leveling_active if appropriate
2017-11-06 18:26:47 -06:00
Scott Lahteine
efc1029226
Update bilinear for native workspace
2017-11-06 17:03:34 -06:00
Scott Lahteine
1b09733e7c
Fix FWRETRACT un-hop
2017-11-05 18:33:10 -06:00
Scott Lahteine
8ab368559a
Implement CNC_COORDINATE_SYSTEMS
2017-11-04 22:30:23 -05:00
Scott Lahteine
91abf07087
Cleanup and fix G33
2017-11-04 22:30:23 -05:00
Scott Lahteine
64f077fd2a
Remove I2CPEM workspace offset
2017-11-04 22:00:45 -05:00
Scott Lahteine
f9f0ee0f21
Update G2/G3 Workspace Planes
2017-11-04 14:35:25 -05:00
Scott Lahteine
640526f0c8
Operate in Native Machine Space
2017-11-03 22:40:30 -05:00
AnHardt
13a3fb1acc
Some cleanup around 'lcd_bootscreen()' and 'lcd_kill_screen()'
...
Move 'lcd_bootscreen()' from `lcd_init()` to 'setup()' where it is cexecute exactly once. Saves 'bool show_bootscreen'.
Move the call of 'lcd_custom_bootscreen()' to the begin of 'lcd_bootscreen()'.
Move the delays into the related functions.
Move the picture loop around 'lcd_kill_screen()' into the function.
2017-11-03 12:16:42 +01:00
Scott Lahteine
343dd1c0b8
Remove G33 trailing whitespace
2017-11-03 04:06:38 -05:00
Luc Van Daele
0e4b6b373d
[1.1.x] G33 magic numbers ( #8173 )
...
* [1.1.x] G33 magic numbers
* oops
* comments
* oops
* warning
* better comment section
* remarks
* extra grids
2017-11-03 03:35:53 -05:00
jmdearras
3e9504d306
Fix case light "off" function ( #8205 )
...
* Fix case light "off" function
It would only turn the light off if brightness was 255
* Update Marlin_main.cpp
2017-11-01 21:17:23 -05:00
Scott Lahteine
4bf0e15653
Allow asterisks in G-Code commands
...
Addressing #6655
2017-10-31 21:14:56 -05:00
GMagician
15be1cb9a9
[1.1.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour ( #8177 )
...
* [1.1.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour
NO_MOTION_BEFORE_HOMING should prevent XYZ movements only when homing is not done.
E axes should be allowed
* Update Marlin_main.cpp
* Update Marlin_main.cpp
* Update Marlin_main.cpp
2017-10-30 22:50:50 -05:00
Scott Lahteine
893092ff7f
Kinematic clamp_to_software_endstops
2017-10-30 16:24:45 -05:00
Scott Lahteine
46ed54cd8e
Include time scale in some planner vars
2017-10-29 18:48:14 -05:00
Scott Lahteine
daa85f71e1
Merge pull request #8123 from thinkyhead/bf1_dual_xyz_endstops
...
[1.1.x] Dual endstops XYZ
2017-10-29 04:36:09 -05:00
Scott Lahteine
318c419f77
Implement support for Dual X and Y endstops
2017-10-29 03:49:45 -05:00
LVD-AC
77cf42588f
(1.1.x) serious bug G33
2017-10-29 00:22:55 +02:00
Luc Van Daele
e64cfb13b8
(1.1.x) auto tune calibration parameters ( #8031 )
...
* auto tune calibration parameters
* solve warnings
* Tweaks to formatting
* review Thinkyhead
* Error
2017-10-26 23:49:20 -05:00
Scott Lahteine
2296d98845
Tweak neopixel self-test
2017-10-26 22:46:11 -05:00
Scott Lahteine
6569b9ba56
Fix FWRETRACT logic, apply common sense
2017-10-26 22:36:41 -05:00
Scott Lahteine
355ebec92d
Fix position sync in M600 pause/resume
2017-10-24 14:41:54 -05:00
Roxy-3D
e9bc9a2ab4
change to better (more clear) names ( #8049 )
...
set_destination_to_current() changed to set_destination_from_current()
set_current_to_destination() changed to set_current_from_destination()
2017-10-21 10:58:17 -05:00
tweichselbaumer
fa44130734
Add M290 babystepping ( #8014 )
...
* Add M290 babystepping
* Allow `Z` for `M290`
* fix spacing
* Support BABYSTEP_XY in M290
* Not just Z
* Extend M290 for BABYSTEP_ZPROBE_OFFSET
* tweak
2017-10-21 03:58:53 -05:00
Luc Van Daele
2a88a3fd33
boolval revised ( #8017 )
2017-10-18 14:19:01 -05:00
studiodyne
e04902f589
Add EXTRA_FAN_SPEED feature
2017-10-16 02:32:30 -05:00
Scott Lahteine
d63d08ef8b
Merge pull request #7948 from gallynero/patch-1
...
Enable change feedrate in delta
2017-10-15 16:28:45 -05:00
Scott Lahteine
5c2ff6ed19
Add Capability BUILD_PERCENT
2017-10-15 03:01:36 -05:00
Scott Lahteine
5f708d47ce
Add LCD_SET_PROGRESS_MANUALLY
2017-10-15 02:21:09 -05:00
Scott Lahteine
060d16d26b
Split the software endstop capability by axis.
...
Based on #7975 and #7979
2017-10-14 17:14:08 -05:00
Scott Lahteine
b8ddae61e2
ubl_state no longer needed
2017-10-14 02:39:13 -05:00
Scott Lahteine
b07a2aa23c
Add HAS_MESH conditional
2017-10-14 02:39:12 -05:00
Scott Lahteine
88857e8028
Move fade_scaling_factor_for_z to Planner
2017-10-14 02:10:46 -05:00
Scott Lahteine
8e808fcadc
General cleanup, apply const
2017-10-13 16:13:36 -05:00
Scott Lahteine
da93a272a0
Move leveling_is_active to a macro
2017-10-13 16:11:27 -05:00
gallynero
94228d4522
Enable change feedrate in delta
...
Enable change the relative feedrate on a printing job in delta machines with UBL
2017-10-12 01:55:51 +02:00
Slawomir Ciunczyk
167058b61f
Different NEOPIXEL types
...
Changes to support NEOPIXEL LED strips
- Support for different NEOPIXEL as defined in Adafruit_NeoPixel.h
- ability to setup startup brightness
- ability to define sequential/non-sequential transition of color change during heating-up
- additional parameter to M150 P<brightness>
2017-10-10 01:58:40 -05:00
jmdearras
c7e0a49c94
Add some new LCD displays
...
- Original CR-10
- MKS Mini Display
2017-10-09 17:39:03 -05:00
LVD-AC
355cba4aa7
Fixes for G33
2017-10-06 15:52:53 -05:00
Scott Lahteine
a47c5c093d
Merge pull request #7459 from ejtagle/xon-xoff-sdxfer
...
[1.1.x] XON/XOFF serial handshake (for faster transfers to SD)
2017-10-02 23:52:41 -05:00
Scott Lahteine
4c34b3ad9c
Stop redundant E4_IS_TMC2130 current control
2017-10-02 23:10:34 -05:00
Scott Lahteine
1b8b5c4b06
Make prepare_move_to_destination_dualx a full move function
2017-10-02 23:10:18 -05:00
Scott Lahteine
4e19ff75b6
XON/XOFF corrections, tweaks, formatting, etc.
2017-10-02 03:52:42 -05:00
Scott Lahteine
f365448338
Merge pull request #7811 from thinkyhead/bf1_fix_resume_print
...
[1.1.x] Fix broken M600 resume_print
2017-10-01 22:54:34 -05:00
GMagician
33d28c24bf
Implementing [FR] #7548
...
Added new configuration to inhibit XYZ movements when home is not done
2017-10-01 21:02:42 -05:00
MasterPIC
40a4a716e1
Fix filament change bug in resume_print
...
Expected behaviour: while (auto)extruding the new filament, the nozzle should not move. It should move (from filament replacement position to printing position) only after the user has confirmed the successful filament replacement and extrusion.
Actual behaviour: while (auto)extruding the new filament, the nozzle moves from filament replacement position back to printing position.
So the extrusion step is mixed with the movement required to go back to the printing position.
The provided code seems to be working but probably a better fix is required.
2017-10-01 18:42:29 -05:00
Scott Lahteine
802f147686
Remove some excess whitepsace
2017-10-01 18:25:04 -05:00
Scott Lahteine
80a0f935a1
Fix G10-G11 by adding a synchronize
...
Based on #7792 by @tcm0116
2017-09-30 17:46:31 -05:00
Scott Lahteine
9bbc2df217
General code cleanup, spacing
2017-09-24 16:52:41 -05:00
Luc Van Daele
74d430cb97
matrix names update ( #7697 )
...
* matrix names update
* symplified names
* new angle normalization
* ABC
* axis
* least squares
* recalc_delta_settings
* endstop_adj
* 0p
* bug
2017-09-24 01:45:31 -05:00
Scott Lahteine
0afd25a010
Fix caselight compile issues
2017-09-23 22:00:44 -05:00
Scott Lahteine
367e1b54ba
Merge pull request #7591 from thinkyhead/bf1_misc_patches
...
M111: no args reports current flags
2017-08-31 15:19:29 -05:00
Scott Lahteine
8a184a526a
Marlin: Patch G33, allow M111 to give status
2017-08-31 14:35:00 -05:00
Scott Lahteine
898f48e331
CNC workspace planes for G5
...
According to LinuxCNC, G5 should throw an error if the current plane mode isn't XY.
2017-08-31 14:29:29 -05:00
