MPCNC/Firmware2
1
0
Fork 0
Code Issues 1 Pull Requests Releases Wiki Activity
1,291 Commits 1 Branch 0 Tags 129 MiB
2ccdf4f36d
Commit Graph

1120 Commits

Author SHA1 Message Date
Alex Borro
5c44f6c434 Bed Heater monitoring in Controller Fan 
In some cases the Bed Heater FET heats up more then stepper drivers, so
this change add the bed monitoring to the controller fan. As soon as the
bed heater is turned on, the controller fan will run as well.
 2013-11-27 23:23:06 -02:00
Alex Borro
b33375d438 Z Axis Safe Homing when using Z Probe 
Recommended for those who are using the Z Probe for Z Homing (as
Z-Endstop)

This feature has two changes:

1) Allow user to choose where the Z Probe will touch the bed when homing
all axis together (G28) by setting below defines:

Z_SAFE_HOMING_X_POINT
Z_SAFE_HOMING_Y_POINT

2) Prevents the user to perform Z Axis Homing when the Z Probe is
outsite bed.
 2013-11-27 22:37:35 -02:00
Alex Borro
35905ea4f9 Allow heaters to stay full On when PWM=127 
In previous version, even with PWM = 127, the system turns the FET off
and then on in the next cycle. This bevavior may increase the FET heat
dissipation.
It was fixed keeping the FET always On when PWM=127.
 2013-11-27 18:13:38 -02:00
Erik van der Zalm
a94e588765 Changed slow buttons behavior. 2013-11-17 17:41:30 +01:00
Erik van der Zalm
69af392554 Added HEATERS_PARALLEL (Request from reifsnyderb) 
This allows a hot end with two heaters and a FET for each heater. This is useful if the FET is not capable of heating two heaters.
 2013-11-17 13:29:02 +01:00
Erik van der Zalm
48a185d004 Fixed compile errors from bad commits. 2013-11-10 16:36:37 +01:00
ErikZalm
24d1f480b6 Merge pull request #647 from shaggythesheep/newfeature-M226 
Implement M226 - GCode Initiated Pause
 2013-11-10 07:27:01 -08:00
ErikZalm
95b41413e6 Merge pull request #641 from hugokernel/master 
M80 - ATX Power On related modification
 2013-11-10 07:26:35 -08:00
ErikZalm
59b96e323e Merge pull request #640 from fmalpartida/SAV-MkI 
Added support for BT on AT90USB devices, corrected LCD bug, added new board and LCD
 2013-11-10 07:26:08 -08:00
ErikZalm
2433ee6fc8 Merge pull request #637 from justuswilhelm/Marlin_v1 
Fix servo control for Melzi v2.0
 2013-11-10 07:22:12 -08:00
ErikZalm
3455a2bac2 Merge pull request #636 from PrintToPeer/Marlin_v1 
Add UUID support to M115 responses.
 2013-11-10 07:21:46 -08:00
Richard Miles
dc887ef99b Implement M226 - GCode Initiated Pause 
Implemented M226 as described here:
http://reprap.org/wiki/G-code#M226:_Gcode_Initiated_Pause

Waits for pin to be become either HIGH, LOW or the inverse of what it
was before. Allows printing to pause until user interaction
 2013-11-09 15:11:58 +00:00
Charles R
c244eb860c If you have a switch on suicide pin, this is useful if you want to 
start another print with suicide feature after a print without
suicide...
 2013-11-04 12:04:04 +01:00
fmalpartida
7b556d2e96 Added BT support on AT90USB devices 
Added AT90USB device BT connectivity support using second UART.
 2013-11-03 19:57:06 +01:00
Kaz Walker
a5e8575829 Add UUID support to M115 responses. 2013-11-01 14:51:50 -06:00
Daniel Benamy
cab84e0e5b Add (correct) missing pin definitions for Y2 
I tested this and it works.
 2013-10-30 22:44:20 -04:00
fmalpartida
5b3f60ea2e Corrected LCD only error 
If only an LCD is defined and no menu or keyboard defined, there is a
compilation error.

Added conditional compilation.
 2013-10-30 21:52:46 +01:00
Justus Perlwitz
62d0b79023 Fix servo control for Melzi 2013-10-30 20:59:58 +01:00
fmalpartida
b5a964fcc5 Initial SAV MkI (RepRap CloneWars board) integration. 
Included support for BT dongle on AT90USB boards.
Added LCD Shift Register LCD control
Included support for RepRap Clone Wars project board (SAV MKI).
 2013-10-30 11:45:32 +01:00
dumle29
f941203172 PS_ON configurable boot state 
Allows the user to select wheter or not the PSU should be turned on or
kept in standby when marlin boots
 2013-10-29 18:44:56 +01:00
whosawhatsis
c79e3967b3 Make G11 not horribly broken 2013-10-24 18:58:42 -07:00
bkubicek
d69822ed51 Fix '#' 
since it can occure in comments.
 2013-10-22 10:34:51 +02:00
bkubicek
2fb2a0a119 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2013-10-22 10:08:21 +02:00
bkubicek
39d88bcccb preparation for hibernation 
If a print is stopped, it would be nice in the future to write a file with the printer state, the filename of the print, and the position within the print.
this file could be read, to continue a previously stopped print.
not finished yet.
 2013-10-22 10:04:08 +02:00
bkubicek
ab965376ff Sub-file calls. 
by overloading M32 it is now possible to execute gcode files from other gcode files, with a fixed recursion level.
This can be used e.g. for having a real start.g and end.g somewhere on the sd card, which are then called from the normal print file.
Another usecase would be to have macro-files for nozzle-change and layerchange.
I have not tested the speedwise performance. The testing was done with pronterface.

syntax:
normal call from sd card will open the new file and continue executing there.
M32 !/path/filename#
this however will call the new file and return to the caller file.
M32 P !/path/filename#
with the optional "S<position>" the  file starting position can be set.
this is for continuing prints from a previous location.
 2013-10-22 10:02:18 +02:00
bkubicek
b2cc27e5ea Added a magic character for sd buffering. 
if a '#' is read now the buffer will be emptied before reading ahead.
This is so one can execute files from within gcode files, without messing the buffer with preread characters from the caller file.
# can not occure in sd files imho, because it should only occure within checksums in ther serial communication.
Yes, thats a lame argument. If you have a better idea please tell me. It has to be a character that one can type
on a keyboard manually.
 2013-10-22 09:54:13 +02:00
Erik van der Zalm
8a08cca0f2 Added temperature status less. 
Hopefully fixed viky button handling without braking other boards
 2013-10-20 12:12:35 +02:00
Erik van der Zalm
667d278f54 Revert "Fix for Viki display" 
This reverts commit 314fd13c39.
 2013-10-20 10:16:46 +02:00
Erik van der Zalm
bf27e79e74 Small BlinkM fix 2013-10-20 10:06:02 +02:00
Erik van der Zalm
87e28c0599 Added ifdefs to blinkm 2013-10-20 09:55:15 +02:00
Erik van der Zalm
24c6b2ab35 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2013-10-20 09:51:58 +02:00
ErikZalm
6a803ba9c5 Merge pull request #590 from timkoster/Marlin_v1 
Added BlinkM support over i2c
 2013-10-20 00:51:35 -07:00
Erik van der Zalm
457d8a0acb Fixed merge conflicts 2013-10-20 09:50:27 +02:00
Alex Borro
6f85a8c7aa Bed auto Leveling change: Raise Z before homing 
- Added "Z_RAISE_BEFORE_HOMING" for raising Z the defined distance
before homing. This is useful to avoid Z-Probe collision when hotend is
near bed.

- Fixed the issue of Z not going bellow Z_PROBE_OFFSET when
"min_software_endstops" is true.
Now the Z_PROBE_OFFSET is not set in Z_MIN_POS, it is added after
homing.
 2013-10-12 17:28:11 -03:00
Alex Borro
dd3086d3f2 Show Temperature ADC values 
If "SHOW_TEMP_ADC_VALUES" is defined in Configuration_adv.h, the M105
command will present, after tradicional temperatures, the ADC value read
from temp sensors. This is great for adjusting thermistor tables with
thermocouple.

From Pronterface you can see the ADC value and compare with a
thermocouple reading.. then you just need to create your own thermistor
table.

Since this merge doesnt change the original information, it doesnt mess
with PC software parsing (tested under Pronterface and Repetier-Host).
 2013-10-12 10:41:23 -03:00
bkubicek
7fad13a1e2 Reverse SD card file name order. 
This is _not_ automatically the cronological, since deleting a file will free
the filesystem descriptor for it, which then will be used by the next file copied on it.
Since this makes the auto0.g file very inaccessible, I put the option back, to have it in the prepare menu.

this should satisfy https://github.com/ErikZalm/Marlin/pull/373

as a reminder, auto0.g will be executed every time after a boot with sd card present and file present.
thereafter, if there is a file auto1.g this will be done. Thats IMHO the best place to put settings, and prepare heating.
I also execute again after each (now again via the prepare menu) before starting a new print/ after a failed one.
It for me 100% replaces any start.gcode form the slicers.
 2013-10-12 13:24:55 +02:00
bkubicek
b832f5b9f6 added delta tower babystepping. Its untested, but hopefully florian horsch will be able to try. 
also, removed some trouble for compilation with corexy.
I think that babystepping is only possible in z for a delta tower.
not sure if it would be usefull to step individual motors on a delta, i don't own one
 2013-10-07 09:14:04 +02:00
bkubicek
c38b0855c8 I think that filament change is ready for the masses. I have tested very often with my ultimaker. 
I strongly vote for it being a single gcode, because otherwise the triggering from the menu is terrible.
 2013-10-06 21:20:26 +02:00
bkubicek
d147a057ac Add the socalled "Babystepping" feature. 
It is a realtime control over the head position via the LCD menu system that works _while_ printing.
Using it, one can e.g. tune the z-position in realtime, while printing the first layer.
Also, lost steps can be manually added/removed, but thats not the prime feature.
Stuff is placed into the Tune->Babystep *

It is not possible to have realtime control via gcode sending due to the buffering, so I did not include a gcode yet. However, it could be added, but it movements will not be realtime then.

Historically, a very similar thing was implemented for the "Kaamermaker" project, while Joris was babysitting his offspring, hence the name.

say goodby to fuddling around with the z-axis.
 2013-10-06 21:14:51 +02:00
Erik van der Zalm
bca353cc12 Fixed duplicate define in fastio.h 2013-10-03 19:24:53 +02:00
Alex Borro
253dfc4bc1 Bed Auto Leveling feature 
Check the Readme for instruction how to enable and configure the feature
 2013-09-29 13:20:06 -03:00
ErikZalm
1bda6bf862 Merge pull request #609 from phq1910/patch-1 
Update Configuration.h
 2013-09-26 11:47:58 -07:00
ErikZalm
c80aac1518 Merge pull request #610 from phq1910/patch-2 
Update pins.h
 2013-09-26 11:47:47 -07:00
Erik van der Zalm
314fd13c39 Fix for Viki display 2013-09-26 20:32:19 +02:00
phq1910
4f7c6dfe35 Update pins.h 
Include Pins cpu Sethi 3D
 2013-09-26 11:40:54 -03:00
phq1910
57173739a1 Update Configuration.h 
Include CPU Sethi 3D
 2013-09-26 11:29:44 -03:00
Erik van der Zalm
0dca49a7c0 Added Azteeg X3 board. 2013-09-24 17:31:16 +02:00
Erik van der Zalm
d8c2c810b4 Added info to the delta configuration files in the configuration.h file 2013-09-23 23:29:46 +02:00
Erik van der Zalm
9bc88f8bab Placed optional ENCODER_PULSES_PER_STEP in the configuration.h file 2013-09-23 23:25:11 +02:00
Erik van der Zalm
3ca1ca6869 Fixed missing ENCODER_PULSES_PER_STEP 2013-09-23 23:18:35 +02:00
Tim Koster
97b0da0c2e Removed #ifndef BLINKM 2013-09-22 10:43:27 +03:00
Tim Koster
61db046b32 Added #ifdef BLINKM around new code. Also refined BlinkM.h. 2013-09-20 10:57:42 +03:00
Richard Miles
77df2ab0e7 Make Y_DUAL_STEPPER_DRIVERS disabled by default 2013-09-17 21:49:44 +01:00
Richard Miles
ed1ab42186 Added Y_DUAL_STEPPER_DRIVERS 
Enables two stepper drivers to be used for the Y axis (useful for
Shapeoko style machines)
Each Y driver can be stepped in either the same way or in opposite
directions, accounting for different hardware setups (leadscrew vs. belt
driven)
 2013-09-17 19:19:20 +01:00
Richard Miles
f4a59e4ce5 Revert "Added Y_DUAL_STEPPER_DRIVERS" 
This reverts commit 7ee275b620.
 2013-09-17 19:05:49 +01:00
Richard Miles
7ee275b620 Added Y_DUAL_STEPPER_DRIVERS 
Enables two stepper drivers to be used for the Y axis (useful for
Shapeoko style machines)
Each Y driver can be stepped either the same way or in opposite
directions, accounting for different hardware setups (leadscrew vs. belt
driven)
 2013-09-17 19:02:00 +01:00
ErikZalm
6a1e980c6d Merge pull request #600 from xoan/Encoder_Pulses_Per_Step 
add ENCODER_PULSES_PER_STEP
 2013-09-14 04:56:45 -07:00
ErikZalm
20076a8bd3 Merge pull request #598 from GDV0/Marlin_v1 
FIx compilation error when enabling SERVO_ENDSTOPS (#591)
 2013-09-14 04:54:19 -07:00
Erik van der Zalm
3626b5ad8b Removed Delta from the default config file. 
Changed EEPROM CHITCHAT behavior. M503 is always enabled.
 2013-09-14 13:50:09 +02:00
Xoan Sampaiño
bf7007d02f add ENCODER_PULSES_PER_STEP 2013-09-13 04:12:51 +02:00
GDV0
f17506c504 FIx compilation error when enabling SERVO_ENDSTOPS (#591) 2013-09-11 23:09:37 +02:00
Martin Lukasik
acd8619809 Fan fix for Panelolu2+Sanguinololu. 2013-09-10 22:10:58 +01:00
George Roberts
595580556c Fixed bug that makes ulticontroller knob backwards introduced Feb 28 2013 by Robert. 
Bug introduced in version 6beb42cdf6.
Robert did a good job of simplifying but messed up this chunk of code.

Looking at working version: 839bef6d5d
it seems there is no case where encrot3 should be defined as 2
because if ULTICONTROLLER is defined then NEWPANEL is also defined.
 2013-09-10 09:56:19 -04:00
Tim Koster
88dfeefca3 Define BlinkM default disabled 2013-09-10 12:32:21 +03:00
Tim Koster
5350faf2a2 Merge https://github.com/timkoster/MarlinBlinkM into Marlin_v1 2013-09-10 12:27:26 +03:00
Tim Koster
7016cc9511 Added BlinkM support over i2c 2013-09-10 12:18:29 +03:00
Tim Koster
3b315b3da0 Added BlinkM support over i2c 2013-09-06 22:25:39 +03:00
Jim Morris
f26f26b7bd Fix the example delta configuration as someone forgot to do it. 2013-09-05 16:36:55 -07:00
Peter Hercek
9aa2229077 add command M666 for adjusting delta printer endstop position 2013-08-28 01:15:20 +02:00
Robert F-C
9547fb9dfb Add duplication and auto-park mode for dual x-carriage support. 2013-08-08 00:10:26 +10:00
Steve Kelly
53614e5144 add pins for rambo lcd 2013-08-03 11:45:53 -05:00
Steve Kelly
b42d24e31e add additional pins to avr2560 for rambo lcd 2013-08-03 11:37:12 -05:00
Nicolas Rossi
b0c8120fcc Added feedrate setting in exemple config for manual moves from panel 2013-08-03 13:09:53 +02:00
Nicolas Rossi
a54fe2d73c Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1 
Conflicts:
	Marlin/Marlin_main.cpp
 2013-08-03 13:05:56 +02:00
ErikZalm
7ea63d08df Merge pull request #565 from iXce/avrdudeconfpath 
Detect OS in Makefile to use the correct avrdude.conf path
 2013-08-02 13:16:07 -07:00
ErikZalm
4187b637a5 Merge pull request #570 from hg42/separate-INVERTING-macros-for-MIN-and-MAX-endstops 
separate INVERTING for MIN and MAX endstops (6 #defines instead of 3)
 2013-08-02 13:15:30 -07:00
ErikZalm
07e7de3600 Merge pull request #569 from hg42/convert-PROTOCOL-macros-from-statements-to-expressions 
convert PROTOCOL macros from statements to (multiple, comma separated) expressions
 2013-08-02 13:13:29 -07:00
Guillaume Seguin
c0c4c97db6 Detect OS in Makefile to use the correct avrdude.conf path 2013-08-01 19:20:27 +02:00
hg42@gmx.net
2ca983568d separate INVERTING for MIN and MAX endstops (6 #defines instead of 3) 2013-08-01 15:06:39 +02:00
hg42@gmx.net
3700f688f5 convert PROTOCOL macros from statements to (multiple, comma separated) expressions 2013-08-01 14:56:39 +02:00
daid
a504c88346 Fix a bug where the PID controllers D action kicks in hard as soon as the PID controller starts. 2013-08-01 14:12:30 +02:00
Nicolas Rossi
394ed08f88 Added feedrate setting for manual moves from panel 2013-07-30 14:33:30 +02:00
Nicolas Rossi
9bf1cf1b22 Pre-calculate diagonal rod length squared 2013-07-30 14:09:21 +02:00
Nicolas Rossi
4623e78ce0 Added Honeywell thermistor 135-104LAF-J01 2013-07-30 14:02:18 +02:00
Brendan-csel
d7f384f680 Skip SD menu refresh if nothing has changed 2013-07-30 14:02:15 +02:00
Brendan-csel
abc8320a68 Save LCD_CLICKED before it is cleared 
The SD card menu was refreshing so slowly that the button interrupt was clearing LCD_CLICKED before the menu items could check it.
 2013-07-30 14:02:13 +02:00
Guillaume Seguin
f4c3135c6d Add Panelolu2 pins for RAMPS1.3 2013-07-30 14:02:11 +02:00
Guillaume Seguin
aae42c68f9 Update French translation in language.h 2013-07-30 14:02:08 +02:00
Guillaume Seguin
4d435c38a6 Add support of LiquidTWI2-based panels to Makefile 
Use LIQUID_TWI2=1 as make argument to enable this support
 2013-07-30 14:02:06 +02:00
Guillaume Seguin
6c42a3a339 Woops, fix logic 2013-07-30 14:02:04 +02:00
Guillaume Seguin
376d8af2c8 Report temperatures for all extruders 2013-07-30 14:02:01 +02:00
ErikZalm
434b6a05c1 Merge pull request #552 from iXce/Marlin_v1 
Report temperatures for all extruders in reply to M105
 2013-07-29 10:39:21 -07:00
ErikZalm
bdc2621119 Merge pull request #561 from Brendan-csel/Marlin_v1 
Fix for Viki LCD issues printing from SD card
 2013-07-29 10:38:17 -07:00
ErikZalm
6965bd4e15 Merge pull request #560 from njprossi/Marlin_v1 
Fixed move from panel for delta bot #557
 2013-07-29 10:37:40 -07:00
ErikZalm
a55b33e613 Merge pull request #559 from iXce/panelolupinsramps13 
Add Panelolu2 pins for RAMPS1.3
 2013-07-29 10:37:03 -07:00
ErikZalm
8b34351537 Merge pull request #558 from iXce/frenchupdate 
Update French translation in language.h
 2013-07-29 10:36:43 -07:00
ErikZalm
735e556724 Merge pull request #555 from iXce/liquidtwi2_makefile 
Add support of LiquidTWI2-based panels to Makefile
 2013-07-29 10:33:54 -07:00
Brendan-csel
d80aecda0a Skip SD menu refresh if nothing has changed 2013-07-29 21:00:29 +12:00
Brendan-csel
be2dea1dc6 Save LCD_CLICKED before it is cleared 
The SD card menu was refreshing so slowly that the button interrupt was clearing LCD_CLICKED before the menu items could check it.
 2013-07-29 20:58:09 +12:00
Nicolas Rossi
55c287a69e Fixed move from panel for delta bot #557 2013-07-28 22:54:37 +02:00
Guillaume Seguin
1902d339b0 Add Panelolu2 pins for RAMPS1.3 2013-07-28 19:19:57 +02:00
Guillaume Seguin
eb23a68e92 Update French translation in language.h 2013-07-28 18:50:47 +02:00
ErikZalm
1561c6df51 Merge pull request #547 from wolfmanjm/delta-configuration 
Setup Default configuration for Deltas if DELTA is defined
 2013-07-24 03:11:36 -07:00
Guillaume Seguin
374bc99fa3 Add support of LiquidTWI2-based panels to Makefile 
Use LIQUID_TWI2=1 as make argument to enable this support
 2013-07-24 12:09:53 +02:00
Jim Morris
ab624eac2a revert COnfiguratiuon to the same as head 2013-07-24 02:57:46 -07:00
Jim Morris
52f79ffeca add an example default configuration for delta style bots 2013-07-24 02:55:52 -07:00
Jim Morris
b9d7ccf1cd Merge remote-tracking branch 'upstream/Marlin_v1' into delta-configuration 
Conflicts:
	Marlin/Marlin_main.cpp
 2013-07-24 02:49:25 -07:00
Guillaume Seguin
d4d1540727 Use -fno-use-cxa-atexit to override gcc --enable-cxa_atexit 2013-07-24 11:19:38 +02:00
Guillaume Seguin
01ed99143c Woops, fix logic 2013-07-23 23:34:42 +02:00
Guillaume Seguin
76841450c8 Only display poweron/poweroff if PS_ON_PIN > -1 2013-07-23 22:28:30 +02:00
Guillaume Seguin
44f327d738 Uniformly reindent language.h 2013-07-23 22:13:40 +02:00
Guillaume Seguin
326d2db025 Update language.h so that all languages compile 
Some strings still need translation, but at least everything compiles.
 2013-07-23 22:11:54 +02:00
Guillaume Seguin
2cb716f513 Run Marlin/language.h through dos2unix 2013-07-23 21:49:37 +02:00
Guillaume Seguin
34da3a0a3f Merge github.com:ErikZalm/Marlin into Marlin_v1 
Conflicts:
	Marlin/language.h
 2013-07-23 21:46:41 +02:00
Guillaume Seguin
18199ff960 Merge github.com:ErikZalm/Marlin into Marlin_v1 2013-07-23 21:33:52 +02:00
Robert F-C
fb5334f428 Fixed compile error when QUICK_HOME is defined. 
As well a couple of minor changes to handling of extruder offset for
dual x-carriage mode.
 2013-07-22 22:46:14 +10:00
Robert F-C
c3568398b5 Disable DUAL_X_CARRIAGE by default 2013-07-20 23:50:30 +10:00
Robert F-C
39cd3dbdbe Remove dual x-carriage functionality that could/should be implemented in slicer 
Also added a couple of missed merge lines in homeaxis() from previous
commit.
 2013-07-20 13:07:50 +10:00
Jim Morris
fb20ceabce enable soft endstops for delta 
disable delta by default
 2013-07-17 16:21:51 -07:00
Jim Morris
d01ee7e7b5 fix zjerk being the same for delta as xy jerk 
add more delta defaults
on delta make second home even slower
 2013-07-17 16:14:07 -07:00
Robert F-C
d7390e13d9 Support dual x-carriage printers 
Dual x-carriage designs offer some substantial improvements for dual
extruder printing.
 2013-07-17 22:44:45 +10:00
Jim Morris
f3aa2a48e7 update max pos 2013-07-17 01:29:51 -07:00
Jim Morris
460751503e Added default configurations for deltas when DELTA is defined 2013-07-17 01:17:27 -07:00
Maik Stohn
9da94c247a fixed bad lcd commit from makr3d 
#elsif does not exist #elif is correct
 2013-07-15 17:34:21 +02:00
Erik van der Zalm
59004023fd Fixed typo 2013-07-15 17:22:56 +02:00
Erik van der Zalm
461dad6e05 Added : M32 - Select file and start SD print (Can be used when printing from SD card) 
Untested
 2013-07-14 22:39:59 +02:00
Erik van der Zalm
c4a2077951 M109 and M190 now wait when cooling down if R is used instead of S. 
M109 S180 waits only when heating.
M109 R180 also waits when cooling.
 2013-07-14 21:10:24 +02:00
ErikZalm
8a2a3ef91d Merge pull request #531 from iXce/Marlin_v1_lcd 
Only clamp panel movements if software endstops are enabled
 2013-07-14 06:50:23 -07:00
Erik van der Zalm
6397b3339c restored configuration.h defaults 2013-07-14 15:49:03 +02:00
Erik van der Zalm
cdaaad3df1 Merge branch 'Marlin_v1' of https://github.com/makr3d/Marlin into makr3d-Marlin_v1 2013-07-14 15:45:49 +02:00
Erik van der Zalm
e3bdefd873 fixed missing #endif 2013-07-14 15:42:53 +02:00
Erik van der Zalm
a5be0c52c6 no message 2013-07-14 15:35:54 +02:00
Michael Mayer
e509cdbeb0 added contrast control function for gLCDs 2013-07-14 15:28:26 +07:00
Michael Mayer
99b7e926e7 added MaKr3d Melzi board 2013-07-14 15:17:55 +07:00
Gabino Lopez
68be33b1fc Update language.h 
I update the spanish Messages, now this compile for spanish language.
 2013-07-04 10:23:00 +02:00
daid
acb3271c9a Merge pull request #534 from xifle/Marlin_v1 
Fixes compiler warning for feedrate deadzone
 2013-07-01 23:41:51 -07:00
xifle
61fe430d4f Should fix compiler warning for feedrate deadzone 2013-07-01 11:10:02 +02:00
Gord Christmas
fde17d5720 Fix for ugly code compilation errors in SERVO_ENDSTOP checks 2013-06-28 08:02:04 -07:00
Guillaume Seguin
aa65c20d1f Only clamp panel movements if software endstops are enabled 2013-06-28 14:18:00 +02:00
Erik van der Zalm
ecf3ab5de4 Added thermistor 60 to configuration.h 2013-06-27 23:25:51 +02:00
Nicolas Rossi
2daa85918e Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1 
Conflicts:
	Marlin/Configuration.h
	Marlin/Marlin_main.cpp
	Marlin/language.h
	Marlin/pins.h
	Marlin/ultralcd.cpp
 2013-06-20 23:59:56 +02:00
Erik van der Zalm
2015989f84 Added DISABLE_MIN_ENDSTOPS 2013-06-18 19:20:26 +02:00
Christian Inci
648d45cfb2 Fix Pin Description Typo 
Reverse 'Bed' and 'Fan' at the RAMPS 33 Description.

Signed-off-by: Christian Inci <chris.pcguy.inci@gmail.com>
 2013-06-16 23:35:33 +02:00
ErikZalm
171719f18c Merge pull request #525 from lajos/ultralcd_pid 
ultralcd.cpp compile errors when !defined(PIDTEMP)
 2013-06-16 00:02:54 -07:00
lajos
b519af4f05 fixed another !defined(PIDTEMP) compile in ultralcd.cpp 2013-06-15 20:49:18 -04:00
lajos
7d03c52511 fixed compile error in ultralcd.cpp when PIDTEMP undefined 2013-06-15 18:09:52 -04:00
lajos
02dee80fa5 added Azteeg X1 motherboard 2013-06-15 16:58:17 -04:00
Henrik Brix Andersen
47dc70e3ec Fix location of avrdude.conf 2013-06-15 09:50:25 +02:00
Henrik Brix Andersen
1d258903bb Allow command line compilation when using BEEPER. 2013-06-15 09:36:55 +02:00
Erik van der Zalm
e34c9981ab Delta disabled by default 2013-06-11 22:33:58 +02:00