MPCNC/Firmware2
1
0
Fork 0
Code Issues 1 Pull Requests Releases Wiki Activity
6,607 Commits 1 Branch 0 Tags 129 MiB
88b38eafd8
Commit Graph

293 Commits

Author SHA1 Message Date
AnHardt
88b38eafd8 Endstop interrupt refinement 
At the start of a move, check if the endstops are already triggered.
The 'change' interrupts will not see a change if already triggered.
 2016-11-19 13:30:49 +01:00
Scott Lahteine
eb120e518c Followup to new endstop interrupts feature 
- Fix typos, verbiage
- Fix naming of `setup_endstop_interrupts`
- Some formatting, indentation, spacing
 2016-11-18 21:53:45 -06:00
AnHardt
f3eee02596 Introduce endstop interrupts 
If ENDSTOP_INTERRUPTS_FEATURE is enabled this tries to set up interrupt routines
for all used endstop pins. If this worked without errors, `endstops.update()` is called
only if one of the endstops changed its state.

The new interrupt routines do not really check the endstops and react upon them. All what they
do, is to set a flag if it makes sense to call the endstop test we are used to.

This can be used on:
* ARM (DUE) based boards - all pins can raise interrupts,
* RAMPS - all 6 endstop pins plus some other on EXT-2 can raise interrupts,
* RAMPS based boards - as long the designers did not change the pins for the endstops or at least left enough,
* all boards, if there are enough pins that can raise interrupts, and you are willing/able to swap with pins dedicated to other purpose.
 2016-11-15 12:07:41 +01:00
Sebastianv650
cdc18f8c22 Remove useless line from stepper ISR 
The flag is already set inside planner.get_current_block(). Doing it
twice isn't making it better..
 2016-11-11 19:35:03 +01:00
Scott Lahteine
00662b8635 Minor babystep cleanup patches 2016-11-03 23:31:45 -05:00
Scott Lahteine
b23d255491 Move macros above Stepper::babystep 2016-11-03 23:31:45 -05:00
Scott Lahteine
cc57d46158 Fix set_position for CoreYZ 2016-11-03 23:31:45 -05:00
Sebastianv650
f9bea7968f BugFix for incorrect E-speed calculation 
The extrusion speed was wrong due to a not high enough precision of
esteps to XY steps, therefore now the target float values are used to
calculate the ratio between XY movement and extrusion speed.
The e_speed_multiplier8 was replaced by an absolute multiplier called
abs_adv_steps_multiplier8, therefore one multiplication and bitshift can
be saved inside the stepper ISR. Due to this, also extruder_advance_k is
better suited inside the planner and not the stepper files any more.
 2016-11-01 08:08:47 +01:00
Scott Lahteine
43df9ace4e Merge pull request #5110 from thinkyhead/rc_z2_min_allowed 
Support Z2 min in M119 report
 2016-10-31 07:59:45 -05:00
Scott Lahteine
75dbb71dd7 Replace block.busy with a block.flag bit 2016-10-30 16:16:28 -05:00
Scott Lahteine
8cebd2a7db Arrange Z2 min before Z2 max 2016-10-29 01:54:19 -05:00
Scott Lahteine
083d41a2c2 Remove redundant estep rate code from LIN_ADVANCE 
As noted by https://github.com/MarlinFirmware/Marlin/pull/4971#issuecomment-252503295
 2016-10-22 02:19:14 -05:00
Scott Lahteine
2cb5df8a56 Merge pull request #4984 from esenapaj/Small-fix-for-PR-#4980 
Small fix for the PR #4980 (LIN_ADVANCE bug fix and optimization)
 2016-10-10 13:30:47 -05:00
Scott Lahteine
f8199b2cc1 Merge pull request #4982 from thinkyhead/rc_abl_bugfix 
Fix planner with kinematics, delta ABL
 2016-10-10 13:24:22 -05:00
esenapaj
cfb5c24bc9 Small fix for the PR #4980 (LIN_ADVANCE bug fix and optimization) 
・Fix a comment about timer
 2016-10-10 07:48:42 +09:00
Scott Lahteine
c5cac486f5 Use a, b, c instead of lx, ly, lz 2016-10-09 14:34:24 -05:00
Scott Lahteine
3752d9aca8 Fix timer comments 2016-10-09 12:11:00 -05:00
Sebastianv650
a448cedbc5 LIN_ADVANCE bug fix and optimization 
.) long to int: Extruder stalls at 10kHz / 20kHz step limits with long.
.) Take the delta_adv_steps calculation out of the step_loops loop. Wasted calculation performance if done inside.
.) >> 2 replaced by 3: Is divide by 8. Reason: Timer 0 runs at 16/8=2MHz, Timer 1 at 16/64=0.25MHz. ==> 2/0.25=8.
 2016-10-09 11:55:02 -05:00
esenapaj
f8df88f271 Move routine of direction signal of ADVANCE and LIN_ADVANCE from Stepper::isr() to Stepper::advance_isr() 2016-10-07 02:01:29 +09:00
Scott Lahteine
ecf7cdde65 Augment planner/stepper getters/setters 2016-09-29 01:27:37 -05:00
Scott Lahteine
5fff8d148b Clean up digital pots and microsteps 2016-09-25 11:16:22 -05:00
Scott Lahteine
cb48292338 Use fastio for literal pins 2016-09-25 06:33:38 -05:00
Scott Lahteine
eabff30e75 Improve MINIMUM_STEPPER_PULSE 2016-09-24 02:23:43 -05:00
Scott Lahteine
cc639d7d9c Less indentation in Stepper::isr 2016-09-23 03:03:14 -05:00
Scott Lahteine
7dec8071b2 Always synchronize in Stepper::set_position 2016-09-23 03:03:14 -05:00
esenapaj
954563d603 Adjust spacing 2016-09-20 19:35:44 +09:00
esenapaj
7e9576dc5b Extend the e_steps[] from int to long for allowing more than 32,767 E steps 
Probably needed for long straight lines when using high microstepping
 2016-09-20 19:35:44 +09:00
esenapaj
b04ed8f9c3 Fix inverted stepper signal of ADVANCED and LIN_ADVANCED 2016-09-20 19:35:44 +09:00
esenapaj
8692748ecd Fix broken direction signal of ADVANCED and LIN_ADVANCED 
Remove a setting proccess of E direction in advance_isr()
 2016-09-20 19:35:44 +09:00
Scott Lahteine
edfaf1c582 Stepper::report_positions patch 2016-09-18 12:58:42 -05:00
Scott Lahteine
6f71bd7372 Merge pull request #4754 from thinkyhead/rc_mixing_regression 
Unify counter_m and counter_M
 2016-09-02 12:27:43 -05:00
Scott Lahteine
9bf78ef465 Fix capitalization of counter_m 2016-09-02 11:31:45 -05:00
Scott Lahteine
42b5616327 Try bool for direction instead of long 2016-09-02 11:28:48 -05:00
Scott Lahteine
d07a913f21 Tweak to stepper advance e_steps update 2016-09-02 02:06:17 -05:00
Scott Lahteine
426f662586 Apply MINIMUM_STEPPER_PULSE in stepper advance_isr 2016-08-30 14:31:48 -05:00
Scott Lahteine
8c7ee4599e Optimize stepper advance_isr 2016-08-30 14:31:48 -05:00
Scott Lahteine
9725bcd099 Minor "optimizations" in stepper ISR 2016-08-30 14:21:43 -05:00
Scott Lahteine
4ec3d1ea58 Add some commentary to stepper ISR 2016-08-30 14:21:15 -05:00
Scott Lahteine
d9bcc7bb45 Set a bool when a stepper block is done 2016-08-30 14:20:48 -05:00
Scott Lahteine
08f717e5f7 Use bit-size typedefs for some stepper vars 2016-08-30 14:19:49 -05:00
Scott Lahteine
759234af60 MINIMUM_STEPPER_PULSE option 2016-08-27 23:58:40 -05:00
Scott Lahteine
a28e15399f Patch stepper.cpp to allow omitting steppers 2016-08-27 20:11:17 -05:00
Scott Lahteine
2f223b8c79 Use ABC and XYZ for "3" 2016-08-21 00:10:08 -05:00
Scott Lahteine
d8f2876753 Replace some float division with multiplication 2016-07-24 13:27:50 -07:00
Scott Lahteine
f8b5749235 Replace division in planner with multiplication 2016-07-24 13:27:49 -07:00
Scott Lahteine
176b9627c7 Some cleanup ahead of BLTOUCH support 2016-07-17 13:55:38 -07:00
Scott Lahteine
05da02f0a2 Implement MIXING_EXTRUDER and SWITCHING_EXTRUDER 2016-07-17 10:53:10 -07:00
Scott Lahteine
4b4a582c4f X_DUAL_STEPPER_DRIVERS implementation 2016-07-11 10:22:19 -07:00
Scott Lahteine
bd491818d6 Reduce storage requirements for strings, make some PGM 2016-06-27 20:36:18 -07:00
Scott Lahteine
61f34eec03 Merge pull request #4125 from jbrazio/bugfix/planner-warning 
Fixes some compiler warnings
 2016-06-22 19:34:37 -07:00