* Make ExtUI respect MAXTEMP limits
- Temperatures are now clamped by MAXTEMP limits rather than arbitrary values.
* Speed up USB init, add status
- Speed up USB initialization
- Show status message if init failed
* Enable status messages for EXTENSIBLE_UI
* Adjust max limit to MAX_TEMP - 15
* Misc. tweaks to formatting, const, etc.
* Remove duplicate calls to PrepareSector
Some flash memory API calls require that a call to `PrepareSector` is done before use. However this call is already made by the LPC1768 framework so the calls in this code are not required.
* Ensure correct alignment of RAM buffer
The LPC176X flash API requires that the RAM buffer used for write operations must be word-aligned. This change ensures that this is the case.
* Add traceback after watchdog timeout
Add the cpability to perform a traceback following a watchdog timeout.
* Enhanced hardware SPI
Allow use of either SSP0 or SSP1.
Ensure that no data is left in I/O buffers after calls to enable sharing of SSP hardware.
* Make flash emulation of eeprom the default
Make use of flash for eeprom storage the default. This means that usage of eeprom will not cause USB drive mount/unmount operations.
* Allow sharing of SD card
SD card I/O operations from the USB stack take place in idle loop, rather than at interrupt time. Allowing sharing of the SPI bus.
New configuration options to allow usage of the SD card to be specified.
* Fix problem with hardware SPI pins
Framework and build platform now located at https://github.com/p3p/pio-framework-arduino-lpc176x and https://github.com/p3p/pio-nxplpc-arduino-lpc176x respectively
fix mkssbase leds
move hardware serial
remove hardware/software serial
Hardware Serial extraction
HardwareSerial ISRs
fix disabled serial2 causing Serial object to link
move usb devices out to framework
separate out adc/pwm peripheral function from hal.cpp
fix includes
remove unused pwm init
move adc
HAL header update
templated filtered adc
LPC1769 platform
- Clean up the API to use a `static` class instance to adhere to Marlin convention
- Add `const` position data access for read/write
- Add Storage capacity to the interface
The current Marlin implementation relies on a timer interrupt to start the ADC conversion and read it. However in some circumstances the interrupt can be delayed resulting in insufficient time being available for the ADC conversion. This results in a bad reading and false temperature fluctuations. These changes make sure that the conversion is complete (by checking the ADC hardware via the HAL) before reading a value.
See: https://github.com/MarlinFirmware/Marlin/issues/11323
Enable the endstop interrupts feature for LPC176x boards. Although Smoothieboard chose to use non-interrupt capable pins for their endstops, and this has been copied by clones, so they can't use it.
* Misc fixes and improvements
- Get rid of most critical sections on the Serial port drivers for AVR and DUE. Proper usage of FIFOs should allow interrupts to stay enabled without harm to queuing and dequeuing.
Also, with 8-bit indices (for AVR) and up to 32-bit indices (for ARM), there is no need to protect reads and writes to those indices.
- Simplify the XON/XOFF logic quite a bit. Much cleaner now (both for AVR and ARM)
- Prevent a race condition (edge case) that could happen when estimating the proper value for the stepper timer (by reading it) and writing the calculated value for the time to the next ISR by disabling interrupts in those critical and small sections of the code - The problem could lead to lost steps.
- Fix dual endstops not properly homing bug (maybe).
* Set position immediately when possible
Use macros that explicitly avoid double-evaluation and can be used for any datatype, replacing `min`, `max`, `abs`, `fabs`, `labs`, and `FABS`.
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
Also simplify logic on all ARM-based interrupts. Now, it is REQUIRED to properly configure interrupt priority. USART should have highest priority, followed by Stepper, and then all others.
