MPCNC/Firmware
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
9,700 Commits 1 Branch 0 Tags 96 MiB
e561ecb5a7
Commit Graph

8040 Commits

Author SHA1 Message Date
Sean
4b36a0a3dc Add acceleration for filament change, load, unload. 
This is useful to achieve a higher movement speed on Bowden extruders.
Also add a slow mode before ramping up to the high speed to make loading easier.
 2018-04-07 23:14:40 -05:00
Scott Lahteine
be0afd71df Add ADVANCED_PAUSE_FEATURE ACCEL options to example configs 2018-04-07 23:14:40 -05:00
Lenbok
0aa833fe6c Chamber temperature monitoring and auto fan control. 
This is an initial cut for feedback.

Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?

Chamber temperatures are not reported on the LCD in any way.

When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.

As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
 2018-04-06 23:09:44 -05:00
Scott Lahteine
08b09f7a4c Add Chamber Temp options to example configs 2018-04-06 23:09:43 -05:00
Roman Moravčík
151962baf2 Update Slovak language (#10313) 2018-04-06 20:20:40 -05:00
Bob-the-Kuhn
aca2bbbc50 Add TMC software SPI pins to pinsDebug_list.h (#10325) 2018-04-06 20:16:05 -05:00
Scott Lahteine
211544b543 Reset progress bar when print ends 
Fix #10330
Based on #10333 by @marcio-ao
 2018-04-06 20:12:40 -05:00
GMagician
8e36d00ad0 [1.1.x] Update language_it.h (#10323) 
Updated to #10296
 2018-04-06 20:07:08 -05:00
Scott Lahteine
ed949cc5c1 Added support for Einsy Retro 
http://reprap.org/wiki/EinsyRetro
 2018-04-05 18:15:58 -05:00
Scott Lahteine
53757444c5 Default active low for TMC2130 DIAG1 (#10294) 
- Added sanity check to require endstop inverting with SENSORLESS_HOMING
 2018-04-05 18:15:58 -05:00
Scott Lahteine
c46d47f45f Scale feedrate (mm/s to deg/s) for SCARA 2018-04-05 16:17:23 -05:00
Anton Piliugin
bc2fc86993 Update language_ru.h (#10311) 2018-04-05 00:47:02 -05:00
Scott Lahteine
dba26a6d1f Add Continuous Purge feature to Advanced Pause 2018-04-04 20:59:50 -05:00
Scott Lahteine
05fc3d7891 Add ADVANCED_PAUSE_CONTINUOUS_PURGE to example configs 2018-04-04 20:53:00 -05:00
Scott Lahteine
7ff70d7adb
Improve heating/cooling LCD messages (#10296) 2018-04-04 19:13:48 -05:00
Scott Lahteine
a7e142460c
MBL should add z_offset regardless of fade (#10307) 2018-04-04 18:27:09 -05:00
GMagician
9d2ef95f1d Additional tool-change fix (#10305) 
Followup to #10243
 2018-04-04 17:06:25 -05:00
Pavel Peganov
de5f69b285 Add Creality CR-8 configuration (#10285) 2018-04-02 19:58:02 -05:00
Scott Lahteine
829281d016
Merge pull request #10243 from thinkyhead/bf1_tool_change_debug 2018-04-02 19:33:27 -05:00
Scott Lahteine
be098cd42f Z Endstop Servo => Z Probe Servo 2018-04-01 23:54:47 -05:00
Scott Lahteine
6444ef02e4 Add remaining boards to Makefile 2018-04-01 18:15:52 -05:00
D-side
ab5232c37b Fix Ender 4 / CR-8 compilation 
- Assign 243 (like EFB) as Ender-4/CR-8 board ID
- Add to `Makefile`
- Add to `pins.h`
 2018-04-01 18:15:52 -05:00
MoellerDi
6b150bfc40 Handle disabled HYBRID_THRESHOLD in EEPROM (#10274) 2018-04-01 16:58:30 -05:00
Scott Lahteine
885ad70c8b Fix likely issue with retract/recover 
Addressing #10200
 2018-03-31 22:59:48 -05:00
Scott Lahteine
d37cfa327e Note about MKS_MINI_12864 in sanitycheck 2018-03-31 22:51:43 -05:00
Scott Lahteine
040ebd1675 Use lcd_printPGM_utf in more places 
Fix #10256
 2018-03-31 20:47:20 -05:00
Scott Lahteine
48fa0e6de0 Output ABC for delta stepper counts 2018-03-31 20:12:53 -05:00
Scott Lahteine
c9aa7486ce Use float62 for LCD edit of Z Fade 2018-03-31 20:02:28 -05:00
Scott Lahteine
80b3f8c395 Allow Z_SAFE_HOMING sanity checks to handle floats 2018-03-31 19:00:14 -05:00
Scott Lahteine
712b213b40 Split up tool_change, raise for non-delta too 2018-03-30 16:06:52 -05:00
Scott Lahteine
52750bf362 Simplified leveling-based tool change 2018-03-30 16:06:47 -05:00
Scott Lahteine
0afdec882c For set_z_fade_height use set_bed_leveling_enabled 2018-03-30 16:06:42 -05:00
Scott Lahteine
29b048810c Symmetrical FWRETRACT Z Hop 
Do the Z lift normally before setting Z back to its prior value. But do the Z lower using spoofing. This should produce proper symmetrical movement.
 2018-03-30 15:47:06 -05:00
Scott Lahteine
0eb1830d85 Change order of inactive stepper disable/enable 
This ensures that steppers that share an enable pin will only be disabled for a miniscule time.
 2018-03-30 15:10:03 -05:00
Scott Lahteine
f5c980f9cf Clear the "Wait for user" message set by M0/M1 
See https://github.com/MarlinFirmware/Marlin/issues/10246#issuecomment-377146936
 2018-03-29 17:57:50 -05:00
Scott Lahteine
d36e950547 Temporary workaround for tool-change compile error 
Pending a more complete solution to tool-change Z deviation.
 2018-03-29 17:57:50 -05:00
Scott Lahteine
df75e9d692 Fix BLTOUCH compile error 
Followup to #10249
 2018-03-29 17:57:49 -05:00
AnHardt
86c3be7089 No delay in sensorless quick homing (#10253) 2018-03-29 16:09:19 -05:00
Scott Lahteine
575b099e40 Alert users about low Z jerk values 2018-03-28 22:58:41 -05:00
Scott Lahteine
360166f626
Merge pull request #10249 from thinkyhead/bf1_homing_move_adjustments 
[1.1.x] Improvements to general and delta homing
 2018-03-28 22:05:40 -05:00
Scott Lahteine
b5f1a4141c "G28 Z forbidden" => "Home XY first" 2018-03-28 21:54:20 -05:00
Scott Lahteine
0401f4ce14 Clear sensorless homing in home_delta after first move-to-top 2018-03-28 21:19:14 -05:00
Scott Lahteine
9f3b4d537d Do moves towards endstops differently in do_homing_move 2018-03-28 21:19:14 -05:00
Scott Lahteine
deefd2defa
Wait before turning off PRINTER_EVENT_LEDS at print end (#10247) 2018-03-28 20:32:32 -05:00
Scott Lahteine
1e31b56b0f Fix checksum + card.saving 
Followup to #10204
 2018-03-28 18:40:36 -05:00
Scott Lahteine
86e58df324 Fix G10/G11 debug logging 2018-03-28 18:40:36 -05:00
Scott Lahteine
3edf9904f4 Fix linear/3-point manual leveling buffer overrun 
Fixes #10137
 2018-03-28 18:40:36 -05:00
Scott Lahteine
8f461568e0 Undo German changes 
See 941e9bd329 (commitcomment-28262166)
 2018-03-28 14:46:42 -05:00
Scott Lahteine
e848bebb10 Fix missing comma in tmc_sgt 
Fixes #10209
 2018-03-28 14:44:30 -05:00
Adrian Cuzman
f84f7e5a38 Require a checksum when writing to SD (#10204) 
When streaming commands to SD with XON/XOFF, errors can occur and cause incomplete commands to be written to the file. This change ensures that only commands with line numbers and checksum will be saved to SD.
 2018-03-28 14:43:41 -04:00
Rob Power
677bd19dbf [1.1.x] NANODLP_Z_SYNC requires linear axes (#10239) 2018-03-28 14:02:58 -04:00
Scott Lahteine
dc05d7fc2b Apply three spaces after pin defines 2018-03-28 12:26:44 -05:00
Thomas Karl Pietrowski
bfdd14be4f bq Hephestos2: Allow bed leveling (#10234) 
* Increases the offset, needed to allow the nozzle to touch the bed
* By default uses an offset of -4. This one is minimally far way from the buildplate and therefore only fine-tuning is needed to set the correct distance.
 2018-03-27 22:06:14 -04:00
Kai
941e9bd329 Update language_de.h (#10216) 
Wrong meaning
 2018-03-25 15:21:26 -04:00
Scott Lahteine
e1f8c97b21
Chinese updates (#10215) 
From #10211 by @yhfudev
 2018-03-25 12:38:08 -04:00
Scott Lahteine
71c05f1b57 Enforce minimum TMC2130 / TMC2208 libs 2018-03-24 15:56:09 -04:00
Scott Lahteine
2c79faede9
Z correction on tool-change for all HAS_MESH (#10198) 2018-03-23 13:11:51 -05:00
Scott Lahteine
94badcbace Use pgm_read_ptr for tables of pointers 2018-03-23 02:17:51 -04:00
Scott Lahteine
2746eb589e Fix size of EEPROM tmc_hybrid_threshold 
Followup to #10101
 2018-03-23 02:04:45 -04:00
teemuatlut
f264228074 [1.1.x] TMC: Match axis label order (#10189) 2018-03-23 01:02:42 -05:00
Roxy-3D
994fdb5179
Get data declarations consistent... 2018-03-22 19:22:49 -05:00
Scott Lahteine
c57545ee08 blocks_queued => has_blocks_queued 2018-03-21 19:08:02 -05:00
Scott Lahteine
647c04def8 Automatically reset stepper timeout in manage_inactivity 
Any code that adds moves to the planner can skip resetting the stepper timeout. We can let `idle` / `manage_inactivity` reset the timer whenever it detects any moves in the planner.
 2018-03-21 19:08:02 -05:00
Roxy-3D
9e987e4971
Correct truncated comment 2018-03-21 16:53:40 -05:00
Scott Lahteine
ba55602462 Tweaks to M915 2018-03-21 05:41:00 -05:00
Scott Lahteine
ec46336df7 For MK2_MULTIPLEXER undef DISABLE_INACTIVE_EXTRUDER 
Fix #10098
 2018-03-21 05:41:00 -05:00
Scott Lahteine
d57adbb88b Trust the bootloader to clear globals 2018-03-21 05:41:00 -05:00
Scott Lahteine
b24099c9d0 Allow G53 to go back to native space 2018-03-21 01:38:41 -05:00
Scott Lahteine
203d3f8f56 UBL G29 parity with 2.0.x 2018-03-21 01:36:16 -05:00
Scott Lahteine
d9e1cbebea Tweak use of move_z_after_probing 2018-03-21 01:36:16 -05:00
Scott Lahteine
e5fbbbc068 Allow no raise after run_z_probe in probe_pt 2018-03-21 01:36:16 -05:00
Scott Lahteine
4eddcf9142 Also suspend keepalive messages with suspend_auto_report 2018-03-21 00:26:00 -05:00
Scott Lahteine
bc01200495
Merge pull request #10101 from thinkyhead/bf1_eeprom_M913 
[1.1.x] More complete Trinamic driver options
 2018-03-20 23:14:10 -05:00
AnHardt
105c81217c Make 2 constants in autotune configurable 
But hidden, since changes are rarely needed.
 2018-03-20 16:39:27 -05:00
AnHardt
3911c38d5e Fix autotune Thermal Protection 
When `THERMAL_PROTECTION_BED` is off but `THERMAL_PROTECTION_HOTENDS` is on, `watch_temp_period` and `watch_temp_increase` are initialized with the values for `THERMAL_PROTECTION_HOTENDS`. Later it is not tested if these values are for the bed or the nozzles.

- Add test.
- Name a constant.

Fix for #10150
 2018-03-20 16:38:38 -05:00
Bob-the-Kuhn
80adb124f7 remove MARLIN line , change to logical pin (#10163) 
delete physical pins from AT90USB
 2018-03-20 16:24:17 -05:00
teemuatlut
8e783e24e8 [1.1.x] TMC: Fix CURRENT_STEP_DOWN (#10169) 2018-03-20 15:15:15 -05:00
Scott Lahteine
8a19bc0c0e Prevent null pointer crash in Endstops::update 
Thanks to Evgeny Kotsuba!
 2018-03-20 04:23:38 -05:00
Scott Lahteine
312bebff9a Add 'I' parameter to M906/M913/M914; 'T' to M906/M913 2018-03-19 22:06:04 -05:00
Scott Lahteine
4995e0ebfa Quiet M906/M913/M914 with axes. Patch for DISTINCT_E_FACTORS. 2018-03-19 22:06:04 -05:00
Scott Lahteine
84bbd018ab Improve Trinamic support in the EEPROM 2018-03-19 22:06:04 -05:00
Scott Lahteine
a03502080e Consolidate smart stepper driver initialization 2018-03-19 22:06:04 -05:00
Scott Lahteine
72776f647b Move _AXIS macro to macros.h 2018-03-19 17:59:59 -05:00
Scott Lahteine
4eb4476ce6
Merge pull request #10153 from thinkyhead/bf1_fewer_options 
[1.1.x] Consolidate 3-point probing, auto delta probe radius
 2018-03-19 04:47:13 -05:00
Scott Lahteine
a66ae52234
Add CorePQ support for BABYSTEPPING (#10074) 2018-03-19 02:51:30 -05:00
Scott Lahteine
68b9503b96 MIN_PROBE_EDGE replaces DELTA_PROBEABLE_RADIUS 2018-03-19 02:17:45 -05:00
Scott Lahteine
cf4e2e507f Consolidate 3-point leveling point options 2018-03-19 01:55:51 -05:00
Scott Lahteine
af3500044a Power off in kill instead of setting PS_ON to input 2018-03-18 20:59:02 -05:00
Scott Lahteine
5793ca42b5 Fix matrix.debug output 2018-03-18 20:03:34 -05:00
Scott Lahteine
07b1ac06a9 More concise tmc_util output, fix a ternary type 2018-03-18 19:10:16 -05:00
Scott Lahteine
bba2a3b906 Prevent lcd_update stack overflow on SD Card change 2018-03-18 18:53:34 -05:00
Scott Lahteine
80c70f33eb Squash UBL G29 postscript comment 2018-03-18 18:35:41 -05:00
Scott Lahteine
d16f443d33
Fix home_delta for SENSORLESS_HOMING (#10144) 2018-03-17 20:52:14 -05:00
Scott Lahteine
f7de05e50c General spacing cleanup 2018-03-17 16:51:34 -05:00
Mitchell Abbott
aef23c9637 [1.1.x] Update X/Y/Z pin assignments for Einsy Rambo (#10131) 2018-03-17 16:40:15 -05:00
Scott Lahteine
7cf2788cc3 Easier override of ST7920 LCD timing 2018-03-17 02:37:24 -05:00
Scott Lahteine
c294613b53 Fix CardReader::getStatus when not printing 2018-03-17 02:37:24 -05:00
Scott Lahteine
6146126b2a Fix SWITCHING_EXTRUDER manual movement 2018-03-16 03:21:56 -05:00
Scott Lahteine
5492f15633 Reduce size of "only one" sanity checks 2018-03-16 02:43:28 -05:00
Scott Lahteine
4d1df2e357 Fix some spelingz 2018-03-16 01:26:38 -05:00